Search Documents

By Bradley V. Johnson

The Bureau of Mines constructed a microminer--a scaled-down (5-by 5- by 11-foot) continuous-mining machine of the drum type with a unique triaxially controlled head--for use in a research program to study the effects of continuous-mining-machine parameters on the generation of respirable dust. This report describes field research with the microminer at the Bureau's Experimental Mine at Bruceton, Pa. Experiments were conducted to determine the effects of depth of cut, rotational speed, and sump and shear rates on the generation of respirable dust. The cutting forces were also monitored and compared with depth of cut. There appears to be a reduction in the amount of respirable dust generated when the depth of cut is increased or rotational is speed lowered, Variation of other machine parameters seems to have little effect on dust generation.

Jan 1, 1975

By James S. Browning

Heavy liquids have been used to separate minerals of different specific gravities for many years.4 5 6 7 8 9/ The method permits substantially quantitative evaluation of a variety of minerals and requires much less time than the usual methods of chemical analysis. This Bureau of Mines investigation was conducted to determine the applicability of heavy liquid mineral separation to the evaluation of certain spodumene and kyanite ores, prepared mixtures, and plant products. After careful standardization of the particular mineral and associated gangue, estimates of chemical analyses could be obtained from results of heavy liquid separations.

Jan 1, 1960

By F. X. Tartaron

Behavior of hard-burned quicklime was compared with that of soft-burned quicklime in an oxygen converter utilizing oxygen blowing in a rotating cylindrical vessel, set at a 30° to 60° angle to the horizontal and operated at a predetermined speed of rotation. Four pairs of tests were made) each comparing hard lime with soft lime. Three of the pairs differed from one another in the quantity of lime employed) and the fourth differed in blowing time, All four pairs showed an increase in yield when soft lime was used. Three of the pairs revealed that the ratio of the oxygen consumed with soft lime to the oxygen consumed with hard lime was the same as the ratio of metal yield with soft lime to the metal yield with hard lime. The fourth pair contained an error and could not be included. Finally, a close inverse relation was found between the combined iron in the slag and the combined lime in the slag, which can be expressed by the equation pct Fe = 52.67 -0,906 (pct CaO).

Jan 1, 1967

By L. B. Berger

Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the dangers of this gas, and frequent now items retort the finding of persons dead or unconscious from the effects of carbon monoxide, yet these accidents continue. Either those warnings are not read, or they are unheeded by people who feel that "It can't happen to me." It can happen to you - carbon monoxide is no respecter of persons, as evidenced by items appearing daily in newspapers all over the country. Carbon monoxide has been a threat to human safety as long as man has used fire to keep himself warm and to cook his food. The burning of any fuel that contains carbon may produce carbon monoxide. This is true of solid fuels such as coal, coke, and wood; of liquid fuels such as oil, gasoline, and kerosene, and of gaseous fuels such as natural or manufactured gas. In the process of combustion the carbon in the fuel unites the chemically with tat oxygen of the air to form carbon dioxide (CO2), however, if the supply of air is not adequate, combustion is incomplete and carbon monoxide (CO) will be formed.

Jan 1, 1943

By John H. Soule

"Although known since 1902, the Capitan iron deposits have not been mined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-45, visited the property; as a result, preliminary sampling of the property was done in 1943.3/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944.4/ Equipment available at that time was limited in the depths that could be reached; and, as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.The following sections note the location and accessibility of the deposits and mention the physical features, climate, labor and living conditions. Property and ownership are outlined, the history and production of the property stated briefly, and the ore deposits are described. The work done by the Bureau of Mines is explained and supported with maps, sections, and assay logs.From March 1, 1944, to June 1, 1944, 179 wagon-drill holes totaling 3,490 feet and 4 test pits totaling 75 feet were completed, and from November 1947 to February 1948 seven churn-drill holes totaling 2,488 feet were drilled and sampled. Metallurgical tests are summarized and referenced.With respect to this report, special acknowledgment is due to J. H. Hedges, chief, Tuscon, Ariz., Branch, Mining Division, and to W. R. Storms, engineer in-charge of the Silver City, N. Mex., field office. Acknowledgment also is due to J. Bruce Clemmer, chief, Tuscon Branch, Metallurgical Division, for analyses done in the last phase of this project, and to Dr. Vincent Kelley of the Federal Geological Survey for his cooperation during this work.The Capitan iron deposits are in secs. 10, 11, 13, 14, and 15, T. 8 S., R. 14 E., central Lincoln County, N. Mex., as shown on figures 1 and 2. The only known large deposit upon which the Bureau did development work lies around the common corner of secs. 10, 11, 14, and 15, as shown in figures 2 and 3, and just southwest of and in the foothills of the Capitan Mountains. This range of mountains trends east and west. The elevation of the highest peak is 10,205 feet.The deposits are reached by traveling on State Highway 48 from Capitan north for 4 miles, to a point just inside the Lincoln National Forest fence and thence due east over a poor dirt road for 1.2 miles. Just over a small wooden bridge, the left-fork is taken, and the poor road is followed to the deposits, a further distance of 1.1 miles (see fig. 1). This road follows the fence to and through the Davis ranch. All the roads from Capitan to the deposits are dirt roads but are impassable only for short periods during and after heavy rain or snow."

Aug 1, 1949

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By Robert W. Smith

[In a certain application it was necessary to compute the incomplete beta function, ß(1/2, p, q), for a certain set of values of p and q. Since the set of p and q values was much more finely spaced than those in any published tables, the authors have decided to make their results available in this report. In connection with this application, the function ß(1/2, p, q) was needed at various points in the p, q plane at intervals of 0.05, 0.05 p = 2q < 10.00. Fletcher, Miller, and Rosenhead3/ state that the only tables available in the desired range are those of Pearson.4/ However, the interval used by Pearson was not small enough for the present application. For this reason, it was decided to calculate the function ß(1/2, p, q) for p = q = 0.05 (0.05) 10.00. This table is published because of the fundamental importance in mathematical analysis of the incomplete beta function.]

Jan 1, 1953

By E. P. Youngman

By a decree of March 14, 1929,5 the President of the Faitian Repub- lic, considering it to be necessary, until the mining legislation of the Republic shall have been revised, to put into effect the mining law of Decem- Der 4, 1860 (relative to mines, diggings, and quarries), by the authority given in article 55 of the Constitution, declared the law of February 14, 1919, to be abrogated and the provisions of the earlier mining law (December 4, 1050) again to be valid. No concessions were granted under the law of 1919. All citations in this paper, unless otherwise designated, refer to the law of 1930.

Jun 1, 1932

By J. J. Forbes

The Coal Mine Inspection Branch of the Health and Safety Division, Bureau of Mines, was established to carry out the provisions in Public Law 49, 77th Congress, H. R. 2082, approved May 7, 1941. The series of major disasters that beset the coal-mining industry in 1940 aroused public interest in mine-safety measures, and the act 18 the direct result of this rekindled interest. Under the provisions of the act, the Secretary of the Interior, acting through the Federal Bureau of Mines, is authorized and empowered to make, or cause to be made, annual or necessary inspections and investigations in coal mines, the products of which regularly enter commerce or the operations of which substantially affect commerce. The principal functions of the Federal coal-mine inspectors are to determine the causes of accidents and occupational diseases in coal mines and then endeavor to eliminate or ameliorate them (1) by revealing, through personal conferences with mine personnel, correspondence, and published reports, the unhealthful and unsafe conditions and practices existing in the mines and (2) by recommending practical means for correcting the conditions observed. The act does not provide any enforcement powers, and therefore compliance with the inspectors&apos; recommendations is not mandatory; it does give Federal coal-mine inspectors the right to enter coal mines for inspection purposes.

Jan 1, 1951

By Donald O. Rausch, Robert H. Merrill, David W. Wisecarver, S. Jackson Hubbard

Results are reported for stress - relief borehole - deformation measurements made in three underground openings near open - pit mines in the Ruth mining district , Nevada . A total of 134 deformation measurements were made in 8 boreholes . These measurements determined the regional stresses in the horizons above , below, and at the elevation of nearby open - pit mine floors ; knowledge of these stress conditions is considered essential information relative to certain aspects in the designing of stable pit slopes . The determinations indicate that the stresses in the district are due to the gravitational load of the overburden in a confined stress field .

Jan 1, 1964

By H. H. Heady

A naphtha obtained by destructive, recycle hydrogenation of crude shale oil, produced by gas-combustion retorting of Colorado oil shale, was found by the Bureau of Mines to contain 49.1 percent paraffins, 20.3 percent cycloparaffins, 7.8 percent olefins, and 22.8 percent aromatics. The naphtha contained only minor amounts of sulfur, nitrogen, and oxygen compounds. Compounds containing less than 5 carbon-atoms per molecule were removed by distillation before analysis. The paraffins where predominantly straight-chain compounds; n-Hexane was present in the largest quantity, and the other straight-chain paraffins decreased in amount as the molecular weight increased. The cycloparaffins, which contained both cyclopentanes and cyclohexanes, were evenly distributed throughout the boiling range. Although the naphtha had been produced by hydrogenation, it contained a small quantity of olefins. Straight-chain olefins with a terminal double bond comprised about two-thirds of these compounds. Among olefins with an internal double bond, those having trans configuration were present in three times the quantity of those in the cis form. In the aromatics all but one of the alkylbenzenes having nine or less carbon-atoms per molecule were identified; toluene was present in the greatest quantity. Only a few of the higher molecular-weight homologs were identified. The composition of the naphtha was computed from analyses of 105 narrow¬boiling distillation fractions. Volume, density, refractive indices, bromine number, and an ultraviolet spectrum were determined on each fraction. From these data the hydrocarbon-group composition of each fraction was estimated. A silica gel adsorption analysis was used to check the values of nearly one-third of the fraction calculated from physical-property data. Mass and infrared spectra were obtained on some fractions for identifying individual compounds or types of compounds, such as terminal olefins.

Jan 1, 1960

By Thomas E. Green

A gas volumetric method was developed for determining metallic aluminum at the 0.01-to 0.3-percent level in 100-gram samples of recycled glass. The method is based on the measurement of the change in gas volume produced by the reaction 2 Al + 2 NaOH + 2 H2O ? 2 NaAl02 + 3 H2 using a simple apparatus assembled from readily available glassware. Apart from sampling errors, the precision of the method is within ±5 percent. A minor modification of the apparatus would extend the method to larger samples or samples of higher metallic aluminum content. Metallic iron and metallic zinc do not interfere at the concentrations found in recycled glass recovered from incinerator residues.

Jan 1, 1971

By T. W. Johnson

The Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has in progress a study or the flow of natural gas through high-pressure transmission lines. A major problem of this study is to compare the deliveries calculated from the gas pipe-line flow formulas commonly used, with the metered deliveries from pipe lines in operation. In order to obtain such comparisons a series of tests has bean made on 25 operating pipe lines in Kansas, Oklahoma, Louisiana, Arkansas, Texas, and California ACKNOWLEDGEMENTS Study of the flow of natural gas through high-pressure transmission lines was made under the general supervision of H. H. Hill, former chief petroleum engineer of the Bureau of. Mines, H. C. Fowler, acting chief petroleum engineer of the Bureau of Mines, N. A. C. Smith, superintendent of the Bureau of Mines Petroleum Experiment Station at Bartlesville, Okla., and T. Brandenthaler, chief of the oil and gas action of the Bartlesville station.

Jan 1, 1929

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau&apos;s data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By BUREAU OF MINES

This report is submitted in accordance with the provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1953 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5043, Part I - Oil From Coal. R. I. 5044, Part II - Oil From Oil Shale. Identical in each report, the introduction summarizes research progress made in 1953 under the entire Synthetic Liquid Fuels program. A free copy of each of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Apr 1, 1954

By F. R. Cattoir

Analytical methods are presented in this paper for determining soluble titanium, total titanium, indicated titanium, and average effective valence in titanium chloride - sodium chloride mixtures. In addition, data are given showing the effects of coarse and fine grinding on the degree of oxidation and average effective valence of such samples. INTRODUCTION The Electrometallurgical Experiment Station at Boulder City, Nev., as part of the Bureau of Mines program to obtain more efficient utilization of our natural resources, has been developing and improving titanium extractive metallurgical methods and techniques since 1945. Numerous reports have been published describing development of the Kroll process,4/ the electrorefining technique,5/ and methods of analyzing titanium sponge.6/

Jan 1, 1957

By J. B. Gayle

The rate of oxidation of coals with nitric acid has been used by earlier investigators4 5 6/ for determining fusain and for studying petrographic composition. These workers accumulated considerable evidence indicating that, for coals ranging from lignite to low-volatile in rank, the method gives values for fusain that agree satisfactorily with those obtained by optical methods. One group5/even concluded that, when discrepancies are noted between results obtained by chemical and microscopic methods, the results based on the oxidation reaction are probably the more reliable. Unfortunately, after concluding that the method was valid, most of these workers apparently lost interest. As a result, no attempt to exploit or apply the method to problems of utilization has been reported. Recent studies of the influence of inert petrographic constituents on the properties of cokes made from various coals7/ have indicated a need for additional means of characterizing coals and blends used for carbonization.

Jan 1, 1960

By R. W. Lowe

1. Reserves are estimated in the Nemo, Sewanee, Wilder, and White Oak beds of Fentress County, Tenn. The Wilder is the only bed being mined commercially and contains the largest known reserves. Eleven lesser known beds are present in the county, but not enough information on them was available for estimating the reserves. 2. Known measured and indicated reserves, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 102 million tons as of January 1, 1955. This total includes 66 million tons in beds 28 inches and more thick.

Jan 1, 1956