Search Documents

By Edward L. Burwell

The Bureau of Mines investigated the use of dilute polymer in brine solutions to increase the efficiency of air in gas flooding model oil reservoirs. Slugs (0.23 pore volume) of 500 ppm polyacrylamide were injected into a model, consisting of a high- and a low-permeability core, that had been previously gas flooded to residual oil. Gas flooding was then resumed. Of the total gas volume injected, the percentage entering the high-permeability zone was greatly reduced after polymer injection but remained unchanged when slugs of water without polymer were used.

Jan 1, 1970

Control shearer-generated airborne respirable dust on longwall mining sections. Approach Previous Bureau studies have shown that using high-pressure water can have a significant impact on the amount of airborne dust released into the face airflow while cleaning and controlling the airflow in the immediate cutting zone. The basic concept to improve the drum water spray system was to utilize high-pressure (1,200 psi) inward-facing drum sprays to improve the dust knockdown efficiency of the spray system and confine the dust to the face area. This system would minimize the exposure of the shearer operator through dust avoidance and decrease face dust levels by suppressing the amount of respirable dust that becomes airborne. System Design In-mine tests were designed to provide information that would permit evaluation of the operation with different spray orientations and water spray pressures. This was achieved by comparison with a conventional baseline wet-cutting system consisting of 26 low-pressure bit sprays, located on the hit blocks to provide pick-point flushing. Total drum water flow was 60 gpm and was maintained continuously throughout all tests. The high-pressure inward-facing drum water spray system consisted of sprays located in each bit block, oriented 15° and 30° toward the face. The inward-facing water spray system was operated at either 800 or 1,200 psi.

Jan 1, 1989

By A. J. Barry

This report presents observations made by Bureau engineers regarding hydraulic-powered roof supports that are currently being used or have been used on nearly all operating longwalls in the United States, A comparative summary of specifications for various types of powered supports with a brief description of the mine conditions has been compiled to enable mining engineers and mine operators to readily evaluate the differences in design data. Some of the support data furnished in the field may vary from those listed in manufacturers' brochures because of the trend to customize various support components to meet specific mine conditions. A method of estimating support requirements for different assumed operating conditions is presented. Similar computations for specific mine conditions may be used to make preliminary estimates of support requirements.

Jan 1, 1969

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all mineral to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of force applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective. A consideration of the possibilities of such a method for crushing led to some experimental work of a preliminary nature, the results of which are embodied in this paper. No systematic program was followed in the work and the results are, therefore, not final and far from complete. The success attained so far, with the mediocre apparatus available seems to warrant a preliminary report, with the expressed hope that the work may be carried on as well-outline program covering such phases as have been impossible to investigate at this time.

Jan 1, 1931

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By C. T. Baroch

This report summarizes cost data accumulated during 15 months of sustained operation of the Bureau of Mines Boulder City (Nev.) titanium plant, which had a capacity of about 1,350 pounds of titanium sponge per day. The plant was constructed during the 1952 fiscal year with funds supplied by the Ordnance Corps, Department of the Army. Its original purpose was to engage in process development work as a continuing phase of the Bureau of Mines policy to seek improvements in producing titanium metal. In early 1953 the Defense Materials Procurement Agency contracted with the Bureau of Mines for producing approximately one-half million pounds of usable ductile titanium sponge. Production began in May 1953, ended in September 1954, and yielded 492,503 pounds of acceptable metal. Operating costs covering this period of operation, with suggested depreciation and administrative costs, are given, as well as outlines of building and equipment capital costs. In addition, miscellaneous economic considerations are discussed, including labor and operating-time schedules.

Jan 1, 1956

By G. R. Peterson

The Bureau of Mines evaluated the potential supply of cobalt from known domestic resources, both as a primary product from some deposits and as a byproduct from others, and found that U.S. production could play an important role in meeting U.S. cobalt needs by the mid-1980's. This production would be of a relatively short duration, however, with production declining significantly before the year 2000. As part of the study, a tonnage-price relationship was developed indicating the quantity of cobalt that could be produced from known cobalt-bearing deposits at various primary commodity prices and at a 15-percent rate of return on the required capital investment. All capital and operating costs are calculated in August 1980 dollars, and commodity prices are based on August 1980 prices. Known U.S. cobalt-bearing deposits which represent the current U.S. cobalt reserve base contain some 310,800 metric tons of cobalt in slightly over 1 billion metric tons of demonstrated mineralized material. Approximately 37 percent of the cobalt contained in the reserve base is considered recoverable using existing technology. Of this quantity, some 87,000 metric tons of cobalt is economically recoverable assuming a cobalt price of $25 per pound, a copper price of $1 per pound, and a lead price of $0.40 per pound. Assuming that the cobalt price decreases to $15 per pound, keeping copper and lead prices constant, the quantity that is considered economically recoverable declines to some 45,700 metric tons. Domestic cobalt consumption in 1979 was 7,900 metric tons (17.4 million pounds). Currently, no primary cobalt is produced from domestic resources, and none has been produced since 1971.

Jan 1, 1981

By Nabil A. Bibawy

An improved method for preparing gravimetric standard gas mixtures of helium-4 in nitrogen has been developed by the U.S. Bureau of Mines. A single-pan 12-kg analytical balance that has a sensitivity of 3 mg is used to prepare the mixture. The balance will accommodate a cylinder having a volume of approximately 4 L that weighs approximately 5 kg. The method has been improved to a precision of ±O.04 pct by performing four successive dilutions, by improved handling of gases in the manifold, and by using an improved analytical method to select high-purity gases.

Jan 1, 1990

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars arc characteristically of the 'fire door" type that is frequently encountered on outside exit doors of many public, and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes arc added to the face equipment machinery for which they arty required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. I. Judy (our consultant), etc:

Jan 1, 1974

Many USBM research and information products are available through the systems or formats listed below: Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone 4. After completing your selection, press the start button on your fax machine. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. CD-ROM: This USBM disk is updated quarterly and sold by GPO's Superintendent of Documents. For information on the latest product, please contact Rodger Wedgeworth, 202/501-9557. Internet/World Wide Web: Text and graphics. Access via PC-based browsing software such as Netscape or Mosaic. Universal Resource Locator (URL) is: http:/www.usbm.gav Internet/Gopher Server: Text and tables only. Using Gopher client software, access via port 70 as follows: gopher.usbm.gav Internet System Administrator: webmaster®usbm.gov (or contact your local System Administrator).

Jan 1, 1995

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,421 samples, representing the products of 131 companies. The samples were collected during June, July, and August, 1953. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1954

By R. D. Dey, V. Castranova, J. M. Antonini, J. A. Blackford Jr.

Alveolar macrophages (AM) exposed to cytokines or bacterial lipopolysaccharide (LPS) produce the free radical nitric oxide (NO·) by an inducible nitric oxide synthase (iNOS). They also release reactive oxygen free radicals following exposure to silica dust. The purpose of the present study was to determine whether NO· is produced by rat AM and/or recruited leukocytes following the intratracheal (IT) instillation of silica. Male Sprague-Dawley rats (175 to 225 g) were IT instilled with either silica dust (10 mg/100 g body wt) or LPS (0.25 mg/100 g body wt). After 24 h, bronchoalveolar lavage cells (BALC) and lavaged lung tissue were assayed for iNOS mRNA. Cell counts of BALC and iNOS-dependent (Nw-nitro-Larginine methyl ester [L-NAME]-inhibitable) chemiluminescence generated by AM were also determined. Northern blot analysis demonstrated that the steady-state levels of BALC iNOS mRNA were significantly increased by 3-fold following IT silica and by 7-fold following IT LPS. Partially enriched fractions of either AM or leukocytes from silica-treated rats both exhibited significantly elevated iNOS mRNA in Northern analysis. iNOS-dependent chemiluminescence was significantly increased in AM by 36-fold following IT silica and by 89-fold following IT LPS. Differential counts of BALC showed that AM numbers did not change in any of the treatments; however, red blood cells increased by 30-fold following IT silica and by 23-fold following IT LPS. Total leukocytes (polymorphonuclear leukocytes plus lymphocytes) increased by 58-fold following IT silica and by 274-fold following IT LPS. The results demonstrate that AM and neutrophils iNOS steady-state mRNA levels, AM iNOS-dependent chemiluminescence, and lavagable red blood cells and leukocytes all increased following IT silica. These findings suggest that NO· production in rat AM and neutrophils is increased in response to silica. NO· has the ability to then combine with superoxide and form a highly reactive toxic species, peroxynitrite, which may be responsible in part for silica-induced lung damage.

Dec 1, 1995

By Lucia Kuizon

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the Diamond Peak area comprising 183,000 acres in the Challis and Targhee National Forests in order to evaluate its identified mineral resources. More than 3,000 mining claims were located in three mining districts between the years 1882 and 1986. Approximately 230 mining claims in and the 150 claims adjacent to the study area were current in 1986, when Bureau of Land Management mining records were researched for this study. A total of 1,270 samples were collected from these sites (30 were for alluvial placer). Results of the investigation help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Lead-, silver-, zinc-, copper-, and gold-bearing minerals occur as veins and replacement bodies in shear and fault zones in Precambrian and Paleozoic calcareous Sedimentary rocks that have been complexly folded and faulted. Total production from the three mining districts in the study area was more than 150,000 tons of ore between 1901 and 1982. Approximately 11,600 tons of subeconomic resources consisting of lead, silver, zinc and copper were identified within the area. Over 37,500 tons of lead and zinc subeconomic resources were identified just outside the area. In addition, lead-, silver-, and zinc-mineral resources were identified at 4 mines within 2 miles of the study area. Iron mineral resources were also identified just outside the area.

Jan 1, 1991

Although alternating-current (a.-c.) power systems and equipment have been used in coal mining for many years, most mines in the United States are powered mainly by direct current (d.-c.). There are several logical reasons for this, but the use of d.-c, equipment is, in most instances, a direct outgrowth of the original practice of using such power for haulage systems. For traction equipment such as the electric trolley locomotive the d.-c. motor has ideal operating characteristics, and thus it has been widely used for haulage locomotive service. The first efforts at electrification of coal mines started with the haulage system and from there branched out to include the many types of electrically powered mining machinery used in the industry today.

Jan 1, 1960

By Donna D. Harbuck

The Bureau of Mines has investigated a process to produce titanium powder directly from titanium salts. If successful, such a process could lower the cost and increase the use of titanium. In this study, K2TiF6, K2TiF3, and TiF3 were reduced with potassium in the temperature range of 650° to 750° C. Under certain conditions, titanium powder 1.6 to 3.3 microns in size was produced. After leaching the product with a 0.1M HCl solution, powder impurities as low as 0.04 pct potassium and 0.28 pct fluorine were obtained. However, oxygen levels of over 1 pct and the frequent formation of insoluble byproducts demonstrate the need for further research to make the powder suitable for powder metallurgy applications.

Jan 1, 2011

By J. C. Judd

The Bureau of Mines investigated the recovery of vanadium, uranium, and phosphorus from low-grade phosphorite ores and concentrate by leach-ing with H2S04. Samples containing 0.12 to 0.23 pct V20S, 0.009 to 0.012 pct U30S and 18 to 30 pct P20S were treated by batch-agitation leaching, roasting followed by acid leaching, salt-roasting followed by acid leaching, and leaching under pressure. Maximum recoveries using leaching alone ranged from 78 to 98 pct of the V20S and 74 to 88 pct of the U30S-Leaching under pressure resulted in extractions of 88 to 95 pct of the V20S and 84 to 89 pct of the U30S. Leaching following roasting--with or without NaCI--produced extractions of 97 to 99 pct of the V20S and 86 to 91 pct of the U30a. Depending on the technique(s) employed, phosphate extractions ranged from 89 to 99 pct. Solvent extraction laboratory tests were conducted to selectively re-cover vanadium and uranium values from acid leach solutions. An average of 95 pct -of the U30a was recovered using di(2-ethylhexyl) phosphoric acid, plus trioctylphosphinic oxide. Essentially all of the V20S was recovered with octylphenyl acid phosphate plus isodecanol. The phosphate remained in the raffinate.

Jan 1, 1986

By A. E. Raddatz

The Federal Bureau of Mines, as part of its goal to minimize undesirable environmental impacts associated with mineral processing, has investigated a soda-smelting technique for processing ilmenite into pig iron and a titanium slag that is suitable for a feed to a sulfate-process titania pigment plant. By this procedure, the generation of ferrous sulfate waste and its associated disposal problem is obviated. Molten titania slag was quenched, water leached, and filtered to yield a sodium titanate intermediate product containing about 70 wt-pct Ti02, 1 wt-pct Fe, and 20 wt-pct Na20. This intermediate product, high-soda titanate (HST), was mixed with H2S04, calcined, quenched, and water leached to produce a low-soda titanate (LST) product that contained only 2 wt-pct Na20. Both the HST and LST were evaluated as feed materials for preparing titania by the sulfate process. About 95 pct of the Ti02 was extracted from HST and LST by digestion in concentrated or 50-wt-pct-H2S204 solutions. About 95 pct of the solubilized Ti02 was subsequently recovered from the titanyl sulfate solutions by hydrolysis. Barren solutions from hydrolysis, containing about 26-wt-pct H2S04, were upgraded by vacuum-thermal evaporation or electrodialysis. The regenerated acid solutions were used to digest additional HST and LST.

Jan 1, 1979

By R. V. Ramani

"The importance of adequate mine ventilation for good health and safety conditions has been recognized since miners first ventured underground. All over the world, governmental actions on mine health and safety arc directly connected with mine atmospheric environments their assessment and control. These governmental actions have been, and continue to be, motivated by the repeated experience that potential threats from inadequate control can evolve, either suddenly or in the long-term, into unpleasant reality, with catastrophic health and safety consequences. These governmental actions arc also an indication of the remarkable professional progress being made in the field of mine ventilation.Surely, no developed country allows underground mines to operate without strong measures for the control of ventilation under legislation specific to the mining industry. In the United States, the federal government's responsibility for mine safety has evolved over the years through a series of legislative actions beginning in 1865 and continuing through 1910, 1941, 1947 and 1952.The passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966 (the 1966 Metal Act), the Federal Coal Mine Health and Safety Act of 1969 (the 1969 Coal Act) and the Federal Mine Safety and Health Amendments Act of 1977 (the 1977 Mine Act) arc the most important milestones in this long legislative history. The 1977 Mine Act adopted many of the stronger features of the Occupational Health and Safety Act of 1970, perhaps the most significant piece of legislation on workers' occupational health and safety in US history.It is worthwhile to ask, ""How far has the United States come in mine ventilation since the enactment of the 1969 Coal Mine Health and Safety Act?"" This Act and its associated regulations defined in great specificity many standards for healthful and safe operation of a mine and. in some cases, what constitutes good ventilation practice."

Nov 1, 1995

By E. H. Denny

"IntroductionOn May 27, 1927, a coal-dust explosion occurred at the Palagua No. 5 mine of the Victor American Fuel Company, Delagua, Colorado, resulting in the loss of even lives and in and in considerable damage to the main slope and to several overcasts the explosion did not extend into the mine working where 125 additional men were employed but escaped uninjured. It is believed that the saving of these 125 men and the evidence of large property loss were due in a large measure to coal-dusting and of other sanity measures taken by the coal company management. A number of features connected with the explosion and mine safety practice seem worth the attention of the mining public and grateful acknowledgment is made to the Victor American Fuel Company for its aid in assembling the data herein contained."

Nov 1, 1927

By Robert H. Merrill

This report summerizes the various studies made to determine the size and support of roofs in the upper shale formation, White Pine Copper Mine, Michigan. These studies were a cooperative effort of the White Pine Copper Company and the Federal Bureau of Mines. Before this investigation, the upper shale formation had been found to contain about 30 to 40 percent of the total mineralization in the ore zones. Investigators estimated that this shale could be economically mined by room-and-pillar methods, provided that the roof would stand over spans of 25 to 32 feet. The problem remained to determine the number of bolts required to safely support these spans. Unbonded fractures in the roof structure of the deposit complicated the use of laboratory methods for determining bolted roof support. Therefore, a method was devised to determine the in-place support which would consider the unbonded fractures. In this method the roofs of 3 rooms with spans of 20, 28, and 36 feet were intentionally overbolted as the rooms were mined. Following stability tests that sometimes exceeded 6 months, the bolts were selectively removed and roof sag, roof strain, and changes in bolt loads were measured concurrently. The number of bolts required for support of these spans was computed from these data.

Jan 1, 1961