Search Documents

By D. C. Dahlin

The Bureau of Mines investigated the Ketchem Dome tin prospect in east-central Alaska to evaluate the tin resource. The studies included field investigations, mineralogical characterization, and concentration of the tin-bearing minerals. The tin mineralization consists of cassiterite (Sn02), which occurs as grains disseminated in a greisen (quartz-mica) matrixo A bulk sample from the largest and best-developed greisen vein exposed at Ketchem Dome contained 0.51 pct Sn. Concentration of the cassiterite by gravity table methods resulted in a product that contained 56 pct of the tin at a grade of 41.4 pct Sn. The mineralization exposed at Ketchem Dome is typical of greisen found in the area and elsewhere in interior Alaska.

Jan 1, 1987

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By G. S. McCaa

Rock-dusting is an. effective means of preventing coal-dust from propagating an explosion in a coal mine, but it will not prevent gas from igniting-explosively and with much attendant damage locally. Ventilation must therefore be effective at all times, regardless of the employment of other explosion-prevention methods, if gas explosions are to be avoided. This paper describes a gas explosion which occurred in as bituminous mine that was well rock-dusted at the point of ignition and which exemplifies the value of rock-dusting, the necessity of maintaining effective ventilation, and the need of permissible rock-dusting machines receiving power from a permissible locomotive. Description of Explosion The mine in which this explosion occurred is developed on a panel system in a practically level seam; the panel entries are driven in pairs, and the air current intakes on the right entry and returns on the left entry. Near the mouth of the intake a door is placed to control the ventilation; board stoppings are placed in crosscuts, except the second from the face, in which a brattice cloth curtain is hung, the last crosscut is left open and line brattices conduct the air current from the last crosscut to the faces. In No. 7 entry the last cross-cut was 152 feet from the face, the line brattice being within 38 feet of this face, and the second crosscut was 250 feet outby the face of the back entry or return. Seven days prior to the explosion the intake and return entries were rock-dusted to within 38 feet of the face, and as the entry had advanced during the week, the rock-dusting was to be extended.

Jan 1, 1929

By David T. Couillard

Task training is increasingly important in mining operations because of the ever-accelerating pace of technological innovations and the concomitant increasing complexity of mining equipment. This Bureau of Mines report describes two successful task training program In use in two open-pit taconite operations in northeastern Minnesota. The programs are different in approach, but both have improved safety and in- creased productivity while lowering costs. Methods of training both before and after passage of the 1977 Mine Safety and Health Act are described, and the impact of this act on task training at each operation is discussed. The report identifies four common principles that have contributed to the success of the two training programs and presents plans each operation has for improving future training through new technology.

Jan 1, 1984

By Richard D. Graves

Pitch from low-temperature carbonization of bituminous coal was hydrogenated at cracking conditions in a continuous bench-scale unit to produce low-molecular-weight oils and tar acids. The pitch contained 15.6 pct benzene-insoluble material, 4.0 pct hexane-soluble oil, and 80.4 pct asphaltene by weight. At 475° C, 7,500 psig, and 1.5 hours residence time, hydrogenation products, based on the weight of pitch, were about 36 pct oil boiling below 325° C, 24 pct hexane-soluble heavy oil, 17 pct asphaltene, 1 pct benzene insolubles, and 12 pct hydrocarbon gases. The yield of tar acids boiling below 250° C was 4.3 pct, and the yields of C6 to C8 paraffins, naphthenes, and aromatics were each less than 1.0 pct. The yield of tar acids was within the range of yields obtained by hydrogenation or high-temperature carbonization of bituminous coal (2 to 5 wt pct). Yields of oil boiling below 325° C increased with increased residence time or temperature. There was little or no effect of residence time on yields of alkali- soluble material which contained tar acids. Yields of hydro-carbon gases increased markedly with an increase in temperature from 475° to 500° C. Lowering the hydrogen pressure to 4,500 psig resulted in yields similar to those obtained at 7,500 psig.

Jan 1, 1962

By S. Gallagher, C. A. Hamrick, A. G. Mayton, R Sonier, R. L. Unger

Introduction Industrial safety professionals recognize that adequate illumination is essential to a safe and productive work environment. The need for effective, lighting in underground coal mines is even greater.1 Designing appropriate lighting systems for these mines is no easy [ ] task because of the unique environment and work procedures encountered in underground coal-mining operations. Miners must depend totally on artificial lighting systems to see. Moreover, the working face is a low-reflectivity and low-contrast environment and is continually advancing or retreating.2 Laboratory mock-ups have been a major part of the process lighting equipment manufacturers must under- go to design an underground machine-mounted lighting system. The mock-ups often have taken considerable time. Furthermore, modifications to a lighting system (using different luminaires with an existing configuration or changing a luminaire's location, orientation, etc.) could require more time with additional mock-ups and laboratory measurements. Understanding the need to improve this situation, the US Bureau of Mines has developed an alternate method for facilitating lighting system mock-ups. A PC-Program (CAP),* with the latest software technology enables users to design, alter, and evaluate under- ground machine-mounted illumination systems. Lux levels and distance are measured as the luminaire is moved incrementally through angular traverses about horizontal and vertical axes. The measurements and angles subsequently are entered into the model. From this input data, three-dimensional isolux or isofootcandle profiles are constructed for luminaires that can be placed at various locations and orientations on a mining machine. As an example, Figure 1 shows a computer display of 21.5 Ix or 2.00 fc profiles for luminaires mounted on a simulated mine-shuttle car. Using this information, the model allows the user to determine the lux level at different locations in space about the shuttle car. How the model calculates illumination During initial development of the CAP model, the isolux profile of the luminaire was determined using the inverse square law (ISL) .3 The method of gathering data comprised recording a single measurement of distance at 21.5 ± 1.21x (2.00 ±11 fc) for angular traverses following 0.09 rad (5 degree) increments. This data was then used to find the illumination in space for any other distance at a given azimuth and elevation using the ISL. Limitations, however, exist with this method.4 The main one is that the ISL assumes a luminaire is a single point source of light, so long as the distance is greater than five times the 1al;gest dimension of the luminous area of the luminaire.5 Also, by using a single measurement to calculate the illumination for a given luminaire in the CAP model a large error could result from an inaccurate measurement.

By R. M. Ray

The Bureau of Mines evaluated five commercial badge-type carbon monoxide dosimeters. Color changes in the badge reagent indicated the presence of carbon, monoxide. Possible effects of ambient conditions on dosimeter response to CO during or after coal mine fires or explosions were studied. Temperature and humidity changes did not change dosimeter sensitivity to CO. Contaminant gases such as CO2, N02, S02, and H2S had effects that varied with brands of dosimeters ranging from no effect to increased sensitivity to CO. Dosimeters tested after 6 months of storage showed an increase in failure rate as high as 25 percent. Tests were conducted to determine the effects on dosimeter time-for-color change caused by observer's sight (colorblind); lighting, and coal dust on dosimeters. No significant effects were observed. Observer variance was the most pronounced factor observed in all tests.

Jan 1, 1975

By R. V. Higgins, A. J. Leighton

A computer program has been devised to calculate the reservoir performance of water floods of complicated well - spacing patterns . The method and program have been tested by calculating the waterflood performance of fivespot patterns using oils of different viscosities and the performance calculations agreed closely with laboratory results . The program on a high - speed digital computer will process the performance prediction in about 1 minute , which is very rapid for a prediction using so much fluid mechanics and nonlinear geometry . The program has been presented in such a way that one may use it as given and save the time required to write and " debug " one of his own . gram processes a complex reservoir analysis , many of the complicated steps are explained in detail , both for the fluid mechanics and the directions for the computer . The subtle features that originally delayed the application of the program to unusual combinations of permeability and viscosity relationships are incorporated and explained

Jan 1, 1963

By L. B. Berger, S. J. Pearce

One phase of Bureau of Mines' work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective. devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus, gas masks, supplied-air respirators. (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks), dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch; approval tests of other types of respiratory protective equipment are conducted by the Health Branch. Both branches are in the Health and Safety Division.

Jun 1, 1950

By Charles Vaught, Richard S. Fowkes, Ronald S. Conti, Barbara Fotta, William J. Wiehagen

The purpose of this study was to determine mine workers' state of fire-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers ' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 1995

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By J. D. Hadden

The Bureau of Mines conducted drilling studies in the Pocahontas No. 3, the Pittsburgh, and a western coalbed to establish the gas migration characteristics for each. Gas pressures in the Pittsburgh coalbed were about 260 lb/in2 and in excess of 550 lb/in2 in the Pocahontas No. 3. Caving in drill holes prevented pressure measurements in the western coalbed. The Pittsburgh coalbed contained intersecting "clay veins" which formed gas pressure cells. Although these geological features hamper mining, they can be used to control the flow of methane into a mine working. Methane control techniques are proposed for the Pittsburgh and Pocahontas No. 3 coalbeds.

Jan 1, 1969

By Chas. G. Maier

The bright annealing of copper is an industrial practice of considerable importance. In connection with this process, equilibrium concentrations of carbon monoxide and dioxide, which may exist in contact with copper and cuprous oxide at elevated temperatures, are of interest. Data obtained at the Pacific Experiment Station of the U. S. Bureau of Mines enable estimates of these equilibrium concentrations to be made in two independent ways. Although the publication of final data on one method can not take place until certain further experimental work is accomplished, repeated requests which the Bureau of Minus has had for data relative to the annealing and deoxidation of copper justify the present preliminary report. This paper deals with the calculation of gas concentrations in the reduction of cuprous oxide, using more scientific data which will be published later, and refers especially to those conditions of temperature and concentration of practical implication, and from which critical limits ensue.

Jan 1, 1929

By Kenneth M. Earl

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the Tapley deposit in an endeavor to find an additional source of copper. There are accounts that many years ago the property had some production; there are several old, inaccessible shafts apparently sunk on a vein in rhyolite or diabase. The waste dumps of these shafts contain considerable sulfides, chiefly pyrite and chalcopyrite. To cut the vein below the old mine workings, the Bureau of Mines? diamond-drilled five holes aggregating 1,204 feet. No significant copper mineralization was found.

Jan 1, 1950

By C. Watson Owings

"The mining Industry in the United States is becoming fully cognizant of the hazards of dust in underground mining as well as in surface plants. The dust problem in metal mines has been brought to focus through knowledge of the harmful effects of dust, especially silica, and through adoption of more or less stringent legislation classifying certain types of pneumoconiosis as occupational diseases. The coal-mining industry is aroused principally by the apparently great increase in the dust-explosion hazard resulting from the rapid growth of mechanized mining. The United States Department of the Interior, through the Safety. Division of the Bureau of Mines, has been requested repeatedly to recommend methods of allaying dust in both coal and metal mines. Methods adequate under hand-mining conditions fail to effect satisfactory reduction of dust in more rapid extraction with modern equipment. Studies of methods and equipment for allaying dust are being conducted in both metal and coal mines. Results of these studies are discussed, and indications of possible means of reducing dust concentrations are presented in the hope that the health and 'safety of men employed in the mining industry may be increasingly safeguarded.DUSTThe term ""dust"" is a common one, and yet the meaning is applied to widely different particle sizes. The general term means ""earth or other matter reduced to fine, dry, and powdery particles."" The root from which the word is derived means ""something that can be blown about by the wind."" As a result of tests on the explosibility of coal, the Federal Bureau of Mines has arbitrarily defined dust as being. ""that which will pass through a 20-mesh screen,"" based upon the fact that particles coarser than 20-mesh have little influence on the development of an explosion of Pittsburgh coal-bed dust. The study of dust, from a health standpoint, has given rise to still another definition of dust, namely,- according to Drinker3/, ""solid particles ranging in size from less than 1 micron to about 150 microns."" A micron is 1/25,400 inch, and 150 microns are approximately 1/1,700 inch. Atmospheric dust usually is considered as 10 microns or less, larger particles not being counted under the microscope in determination of dust concentrations."

Apr 1, 1942

By R. V. Ramani, A. S. C. Owili-eger

List of Numbers

Jan 1, 1974

"Human accidents are caused by production accidents, generally ones (such as derailment of cars, falling rock, etc.) that have occurred numerous times before an employee was actually involved. Prevention of human accidents is, one of the essentials in cutting operation costs, and advocates of safety are studying economics to assist them in their work of preventing accidents.Workman's compensation insurance or compensation for human accidents is a true operating cost, and is the only purely tangible measure available which gives a measurement of the cost of accidents even though, as will be pointed out later, it represents but a portion of the total cost of human accidents.In using premiums paid for compensation insurance as a measure of the cost of accidents, it must be kept in mind that most insurance laws, as pointed out in a former paper (Serial 2590 of the Bureau of Mines) provide a waiting period before compensation for the lost-time wages starts, with the compensation limited to definite percentages of the wages. The waiting period and limited compensation combined tend to limit the amount paid to an injured workman who, if he receives 1/3 of the lost-time wage, will probably have been reimbursed as high as the average injured workman.The total or complete economic cost of human accidents, must include, in addition to compensation paid for lost time, and the portion of the lost-time wage suffered by the workman for which he is not compensated, the additional cost to the company through-(a) temporary decreased production by the breaking down of the morale, etc., (b) the breaking in of a new employee which is admittedly expensive,(c) the increased liability of human and production accidents caused to or by the new employee.Another charge against accidents, which is not included in the compensation payment, is the economic loss through the killing of as workman who has no dependents. Few of the States' laws require any compensation except burial expenses to be paid for fatalities to persons having no dependents. It is estimated by the United States Bureau of Labor Statistics that the economic loss through a fatality is 6000 shifts. If each fatality was compensated for this amount of time and at half-time wages, using an average wage of $5.00 per shift, the compensation for fatality based on the economic loss would be $15,000. but the average actual compensation paid for each fatality is about $3,000."

Jul 1, 1924

By P. J. McDonough

The Bureau of Mines designed and tested a hardware-software system for measuring on-line corrosion rates of materials in a rod mill in operation. Currents ranging from 10-6 to 10-3 A and potentials in I-mV increments were converted to a digital signal. The digitized data were frequency-modulated and transmitted from a rotating ball mill to an FM receiver, where they were decoded by computer and then processed in real time using assembly language software. This design approach would allow accurate measurement and control of systems where signals of small amplitude and large ranges are present.

Jan 1, 1988

By M. Hayashi

The Bureau of Mines conducted laboratory studies on low-grade vanadiferous silicates from the Pumpkin Buttes and Nine Mile Lake deposits of Wyoming to examine techniques for extracting vanadium and uranium. Recovery from low-grade sources such as these could contribute to future vanadium production and reduce reliance on vanadium imports. The Pumpkin Buttes samples contained 0.03 to 0.04 pct V205 and 0.06 to 0.12 pct U308; the Nine Mile Lake samples contained 0.02 to 1.0 pct V205 and 0.06 to 0.19 pct U308" Leaching the Pumpkin Buttes samples for 18 h at 800 C with addition of 200 lb/ton H2S04 resulted in recoverey of 80 pct of the vanadium contained in the samples. The Nine Mile Lake samples were readily leached, yielding 78 to 94 pct of the vanadium after 3 h at 800 C with addition of 100 lb/ton H2S04, A solvent extraction procedure was used to selectively recover urani-um from Pumpkin Buttes and Nine Mile Lake leach solutions and to recover vanadium from the raffinates. In batch shakeout tests, Alamine 336 recovered over 95 pct of the uranium from leach solution adjusted to pH 1. Di-2-ethylhexyl phosphoric acid and Cyanex 272 recovered vanadium from the uranium raffinate after reduction and adjustment to pH 2; vanadium extractions of up to 96 pet and 92 pct, respectively, were achieved.

Jan 1, 1985

By Willard L. Hunter

A series of steel heats, one low-alloy and nine carbon, was made by the Bureau of Mines in a 1-ton arc furnace from ferrous scrap from incinerated refuse, steel cans, and detinned steel cans, both alone and blended with heavy-melting scrap. Two additional control heats, one of carbon steel and one of low-alloy steel, were made from electric furnace heavy-melting scrap to pro-vide comparative data. The steel products were cast into two 4-by 4-inch nominal 50-pound ingots; in most heats, an 8-by 8-inch nominal 7S0-pound ingot was also obtained. Tests of these ingots indicated that reinforcing bars of acceptable quality can be made from urban refuse components such as steel cans.

Jan 1, 1976