Search Documents

By Milford L. Skow

Utilization of domestic ores in the winning of metallurgical alumina requires a convenj.ent method of treating siliceous bauxites and other aluminous materials. In the United states there are only small reserves of high-grade bauxite but considerably larger tonnages of low-grade material. In addition, there are large deposits of high-alumina clays. If these high-silica bauxites or high-alumina clays could be beneficiated, either by are dressing or by chemical dissolution to remove a large proportion of the silica, then the potential reserves of aluminum ores would be increased materially. Faced with a similar situation, the German industry, chiefly dependent on high-grade French bauxites prior to World War II, was compelled during the war to Use lower-grade ores. For desilicating the lower-grade bauxites before the Bayer treatment, a method was developed in which the bauxite was calcined and then given a dilute caustic leach preliminary to the pressure digestion. It was planned to regenerate the caustic by treatment of the desilication liquor with lime. As European bauxites are mineralogically different from those found in this country, preliminary work was undertaken to determine whether this process might be applied to domestic materials. The results of this work, along with a review of the German process, are presented in this report.

Jan 1, 1950

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By Steve W. Webb

The Bureau of Mines is researching a new technology for dewatering clay suspensions that consists of flocculation by high-molecular-weight poly-ethylene oxide (PEO) polymer and subsequent removal of water from the floes via a trommel. The minimum amount of PEO required to dewater the clays depends on the ions adsorbed on the surface of the elay particles. Infrared studies were performed on clays with Li+, NH4+, K+, Mg2+, Ca2+, Ba2+, or 8r2+ adsorbed, with and without adsorbed PEO, to develop data to aid in understanding the dewatering mechanism. Hydroxyl stretching modes between 3,400 and 3,250 em-I, associated with water adsorbed on the clay, showed changes in intensity proportional to the ionic eharge-to-radius ratio; that is, the ionic potential. In addition. a water-bending vibration of adsorbed water at 1,630 cm-1 showed variations associated with water desorption. The data are consistent with changes in adsorption of PEO resulting from variation of the acidity of water coordinated with the exchange ions, induced by the variation in field strength of the ions with the ionic potential.

Jan 1, 1986

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence co-efficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculatlon methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

By Daryl R. Tweeton

The Bureau of Mines compared the effects of surface-active chemicals with those of pure water on core-drilling rock and quartz and on fracturing quartz. The objectives were to determine if these chemicals assist drilling and fracturing rock and if zeta potential control was worth pursuing as an aid to full-scale drilling. All tests were performed in the laboratory. No significant increases in drilling rates were observed for 1 to 10,000 ppm Al (as AlC13) in flushing water when drilling microcline or serpentine, nor for 1 to 10,000 ppm Mg (as MgC12) when drilling microcline or marble. Concentrations near those giving a zero zeta potential were used with microcline and marble. A 50-pct rate increase was observed for drilling quartz in 0.7 ppm oleylammonium acetate, which gave a zero zeta potential. No other concentrations were used. No effect on the tensile strength of quartz thread in 0.05 ppm Al (as AlC13), which gave a zero zeta potential, was observed. Heptanol, reported to give a zero zeta potential on quartz, did not reduce the bending strength of small quartz bars below that in water. These generally negative findings raise doubt about the usefulness of zeta potential control in full-scale drilling. The results, combined with previous studies, suggest that controlling physical properties of drilling fluids, such as viscosity, is more useful than altering chemical properties.

Jan 1, 1976

By Jr. Reed

The only known large deposits of talc in Alabama occur near Winterboro, Talladega County. Preliminary examinations were made, and work by the Bureau of Mines was recommended. The deposits were investigated to determine the amount and grade of talc present and to search for new talc deposits in the general area. Seventy-five holes, totaling 3370.4 feet, were drilled with Government-owned core drills from August 1, 1948, to February 11, 1949, and 27 samples were taken for assay. This report presents the factual data disclosed by drilling and the results of beneficiation of the talc.

Jan 1, 1950

By R. S. McClain

Continuous-circuit flotation and batch-scale precipitation tests were made by the Bureau of Nines to determine rejection of carbon and recovery of fluorine and aluminum compounds from aluminum reduction plant residues, About 40 to 60 pounds each of aluminum fluoride and cryolite are lost for each ton of aluminum produced. Gasoline and turpentine were satisfactory for floating carbon from both fresh water and saturated solution systems. Soluble fluorine and aluminum compounds were recovered by precipitation with sodium aluminate and carbon dioxide. Over 99 percent of the carbon was removed by flotation. Fluorine and aluminum recoveries up to 77 and 63 percent, respectively, were obtained in a combined precipitate and nonfloat product, In the fresh water system the combined product was mostly cryolite with some gibbsite. In the saturated solution system the product was mostly sodium fluoride, some cryolite, and minor amounts of gibbsite.

Jan 1, 1963

By Charles Will Wright

This paper has been written to aid the owner of a small gold mine or prospect in preparing a report on his property for the purpose of interesting capital. If an owner can afford to do so, he should employ a mining engineer of recognized standing and experience to examine and report on his property, but many owners of small -mines and particularly of prospects cannot make the expenditure required for this. Further, many of them do not know how to prepare a description which will cover those features of a deposit on which a potential investor promises his opinion as to its worth. If such an owner is convinced that he possesses an orebody of sufficient grade and size to warrant the required expenditure for a thorough investigation and wishes to present his property to prospective investors, then the following suggestions concerning the proper way to sample his deposit, estimate the tonnage of developed and probable ore, and prepare a report may be of assistance.

Jan 1, 1933

By John Ward Smith

The Bureau of Mines drilled Wyoming Corehole No. 1 in Sweetwater County, Wyo., to sample Green River Formation oil shale. Core obtained was assayed for oil yield to determine richness and stratigraphic distribution of oil shale in the deposit. Oil shale in place at Wyoming No. 1 site represents over 200 million barrels of oil per square mile. Additional data useful in evaluating the deposit, including generalized stratigraphy and mineralogy, detailed lithologic descriptions of the core, rock specific gravity, and bore-hole logs, are presented with the oil-yield data. The sampled Wyoming oil shale resembles Mahogany-zone oil shale in rock properties and gross mineralogy. A statistically derived equation relating shale density to oil yield for the Wyoming deposit compares with a similar relationship valid for the better known Mahogany-zone oil shales in Colorado and Utah. A density log from Wyoming Corehole No. 1 is calibrated for direct oil-yield logging. The alternating rich and lean beds of shale at this site may permit creating the permeability necessary for direct production of shale oil from the shale in place.

Jan 1, 1968

By Irving Hartmann

As part of the continuing effort by the Bureau of Mines to promote mine safety, research work is being conducted at the Experimental coal mine, Bruceton, Pa., on the prevention of coal-mine explosions and on other mine-safety problems. The principal subjects studied during the past 2 years are briefly described in this paper. Although at present these problems are relevant particularly to the mine layout and to high-speed mining practices in numerous American coal mines, it is hoped that the findings will prove interesting and useful also to our European research colleagues. Some of the investigations treated here will be presented in greater detail in forthcoming Bureau of Mines reports. 1. UNDERGROUND STORAGE OF COAL CUTTINGS The seams in mist American bituminous-coal mines are undercut, shear-cut, or top-cut before blasting. The cuttings arc generally loaded out with the balance of the coal. However, in some mines it is not economical to load and remove cuttings from the mine. This applies especially if the cut section of the seam is of appreciably lower grade than the rest of the coal, or if the cut is made partly into an adjacent stratum that is high in incombustible content. In such mines the cuttings are sometimes stored in random heaps in rooms or other areas, along the ribs of mine entries, or in layers on the floor of rooms or entries.

Jan 1, 1956

By Sam McNary

The U.S. Bureau of Mines used the East Fork Pine Creek watershed to conduct a pilot study for an inactive and abandoned mine lands inventory, during which techniques and methodologies would be developed for subsequent inventories. A total of 177 waste dump samples, 191 mill tailings samples, and 36 stream sediment samples were collected. Water samples were collected from 18 sample sites during five sampling events. Waste dump, tailings, and stream sediment samples were analyzed for antimony, arsenic, cadmium, copper, iron, lead, mercury, and zinc. Results indicate a multidisciplinary approach is necessary: disciplines should include geology, geostatistis, geochemistry, geophysics, biology, hydrology, and remote sensing; small prospects do not generally contribute to watershed contamination, major mine and mill sites may contribute metal enriched sediment of metal enriched water; speciation studies and bioavailability studies are important.

Jan 1, 1995

By M. J. Sapko

The U.S. Bureau of Mines has developed a portable meter for measuring the component concentrations in binary dust mixtures whose constituents have different optical reflectivities. The meter has been successfully tested with coal dust-rock dust mixtures taken from coal mines in Europe and the United States and fluorinated-carbon mixtures that change from carbon black to pure white during fluorination. Additional study has also substantiated the theoretical expressions used in the design of the meter.

Jan 1, 2010

By Wm. F. Netzeband

The purpose of this paper is to present to the operators, in other districts a detailed description of the ruining method used and the results obtained to exploiting one of the zinc-lead deposits of the Kansas-Oklahoma-Missouri district. No. 1. mine is located in the heart of the town of Picher in the extreme northeast corner of Oklahoma. HISTORY The first prospect drilling was done at No. 1 mine late in-1914, and shaft sinking was started early in 1915. Sufficient ore was developed to start construction of the mill in April, 1016, Production begin in August, 1916, and the mine s been producing, except for short periods, to the present time. The property was originally a 40-acre tract, but additional properties have been consolidated with the original one until the mine now covers 200 acres.

Jan 1, 1929

By L. B. Pankratzt

The heat capacity of dimo1ybdenum carbide (Mo2C) was measured from 51° to 298° K, and the entropy at 298.15° K was evaluated. Heat content measurements above 298.15° It were conducted for dimolybdenum carbide (M0caY) and monotantalum carbide (TaC). The results were combined with known heats of formation and the 298.15° K entropy for TaC to obtain values of the heat and free energy of formation from 298.15° K to 1,400° K for MoaC and from 298.15°K to 1,800° K for TaC.

Jan 1, 1966

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By T. A. Sullivan

The use of sulfur combined with either sand or waste copper tailings was investigated by the Bureau of Mines as a substitute for a good graded aggregate in asphalt paving materials. The research was part of a utilization program to develop meaningful uses for a projected oversupply of sulfur. Many sections of the country lack good aggregate for paving but do have available sources of sands and sulfur. The development of paving mixtures of desert sands or tailings with sulfur and asphalt was accomplished in the laboratory and tested by laying small paving test sections. Three types of material were studied for use with the sulfur and asphalt. They were (1) a concrete sand similar in gradation to river or beach sands, (2) desert blow sand, and (3) waste copper tailings. Desert blow sand and waste copper tailings are much finer than concrete sand. Mix designs were established for the three types of materials, sulfur, and asphalt used in the paving materials. The best mix designs were as follows, in weight-percent: 80.5 concrete sand, 13.5 sulfur, and 6 asphalt; and 77 either blow sand or tailings, 17 sulfur, and 6 asphalt. Small-scale testing showed that these mixtures were suitable paving materials but would require specialized equipment for transporting and laying. The chemical modification of sulfur to obtain properties that would allow placement of these materials with normal asphalt paving equipment was studied. Results indicate that reacting sulfur with dicyclopentadiene before adding it to the paving mixture was effective in modifying the sand-sulfur-asphalt paving so it could be placed and rolled with conventional equipment.

Jan 1, 1975

By E. G. Davis

Under a memorandum of agreement with Reynolds Metals Co., Richmond, VA, the Bureau of Mines studied the problem of corundum formation on refractory linings in aluminum recycling furnaces. A laboratory test was developed for evaluating refractories in contact with molten recycled aluminum and identifying the mechanism of corundum formation. A test apparatus was designed and constructed to evaluate the performance of refractory samples. Corundum mechanism formation studies indicated that corundum formed on refractories when there is metal penetration. Once corundum forms, it acts as a wick allowing the molten aluminum to move to the surface where it is oxidized, thus causing further growth of the corundum. Phosphoric acid treatment or a spinel mortar coating prevented corundum formation on the 70-and 90-pct-A1203 refractories.

Jan 1, 1988

By R. D. Van Zant

The method for smelting zinc in horizontal retorts developed several centuries ago is still in use. This process consists essentially of the reduction of zinc oxide by carbon at 1,200° to 1,400° C. in a fire-clay retort. The reaction is highly endothermic, and a high radiation loss occurs in transferring the heat of reaction through the fire-clay walls. In recent years, silicon carbide retorts with much better heat-transfer characteristics than fire clay have been supplanting the old retorts. The practical impossibility of recovering the carbon monoxide formed in the reduction causes a large loss of fuel. Intermittent smelting is done in small retorts that are manually charged and discharged, and the furnace crews must be specially trained if efficient results are to be obtained. During the past 20 years several processes have been introduced that have substantially improved the horizontal-retort process. One of these, developed by the New Jersey Zinc Co., consists of a continuous process in which a briquetted mixture of zinc sinter, reducing agent, and binder is coked at 750° to 900° C. and charged into a vertical silicon carbide retort. A supply of displacement air or exhaust combustion gas is introduced at the base of the retort at an appropriate pressure in order to keep the zinc vapor from condensing on the cooled residue in the lower part of the retort. Any .oxidizing constituents in the displacement gas are converted to carbon monoxide by reaction with the carbon in the charge. The spent residue is continuously removed at the bottom of tl1e retort. The chief advantages of this process are said to be increased output per man-day, improved working conditions, high recovery of zinc, increased thermal efficiency, and long retort life.

Jan 1, 1950

By A. U. Miller

Protection against fire is a greater problem at a coal mine, than at an ordinary industrial plant. Generally mines are located in isolated districts and do not have the protection of city fire departments; consequently fire fighting aquipment must be installed by the mining company. Fire protection around a mine is just as essential as it is in the city.. and undoubtedly is more important if the fire should be underground where many lives would be endangered and all means of escape cut off. A surface fire can generally be attacked from any angle, but an underground fire can be attacked only as conditions will permit.. U. S. Bureau of Mines engineers have investigated many serious mine fires that undoubtedly could have been extinguished in incipiency if a fire extinguisher or fire hose and water had been readily available. In past years very little attention was given..to fire fighting equipment and organization around mines, but in recent years three gen a derde hange of opinion among many of those engaged in mining, and nearly all up-to-date mining companies now have some kind of fire protection about their mine Probably the first company in Illinois to install regular fire fighting equipment and effect a fire fighting organization at its mines, was the Madison Coal Corporation, which operates several mines in Illinois. The main office of this company is in Chicago and the general field office is at Glen Carbon, Ill.

Jul 1, 1930

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976