Search Documents

By W. W. Agey

As a result of a field examination made during the Bureau of Mines intensive manganese program, three lots of ore were procured from the famous old Paymaster District, 7 miles from Midway Wells, Imperial County, Calif. This district is an old producer and shipped approximately 10,000 tons of 45-percent manganese ore during World War I. A 2-ton lot of ore was taken of a Bureau engineer from the exposure of a small fissure vein in conglomerate on the Turtle Group of claims; 1 mile east of the Pacific Coast Manganese Corp. claims. The vein material consisted of manganese oxides, calcite, and quartz in fairly coarse association.

Jan 1, 1949

By J. B. Zadra

During the investigations of the occurrence of manganese in the western United States, the Bureau of Mines received a 100-pound sample of manganese ore from the Doyle-Smith property, Yuma County, Ariz. Laboratory tests were made to determine the amenability of this ore to standard ore-dressing methods of concentration to produce a marketable-grade product. The Doyle-Smith claims are in northern Yuma County, within 15 miles of the Artillery Peak deposit. The lot of ore used in the test work was taken from the outcrop of a large, massive, irregular bed of oxide manganese ore found on the claims.

Jan 1, 1952

By W. H. Coghill, B. W. Gandrud, F. D. DeVaney

"The self-fluxing iron ores of Alabama are the foundation of the thriving iron and steel industry of that State. In addition to these deposits of self fluxing ores there are seams containing practically the same percentages of iron but too much silica. These ores at present are valueless, but if they could be concentrated by reducing the silica content, the ore reserves of the Birmingham district would be greatly augmented. A detailed report on the iron-ore deposits of the district, describing the types of ore and their extent, has been published.In forwarding its mineral conservation policies the United States Bureau of Mines has given some attention to the siliceous ores of this district.The low cost of gravity concentration gives this process first rank in the beneficiation of iron ores. For this reason many experimenters have tried to concentrate the Alabama iron ores on tables. In the face of the early failures a new trial has been made and the results have justified the effort.In this work more attention than formerly has been given to the physical, properties of the ores. The removable siliceous gangue is in the form of oolitic grains which ""shell"" out like corn, leaving the hematite as rich high-grade ""slime"" and as clean granular grains. The ""slime concentrate"" may be recovered by well known desliming processes. The oolitic grains and granular hematite are separated on tables."

May 1, 1929

By Stephen P. Holt

During the spring and summer of 1946, the Bureau of Mines put down 8 churn-drill holes and 9 diamond-drill holes, totaling 3,535 feet of bore, at the Blewett zinc-lead deposit in Jo Daviess County, Ill. Attention of the Bureau of Mines was first directed to this deposit by the Illinois State Geological Survey, which had investigated the Blewett mine. In the opinion of the Survey and the Bureau of Mines, the record of production and results of drilling previously done on the property were considered sufficient justification for continuing investigation to the north and south along a projection of the trend. This report describes the work done by the Bureau on this, property and presents the data obtained.

Jan 1, 1948

By Roy L. Wilfong

The linear expansion of high-purity oxides of yttrium, cerium, samarium, europium, and dysprosium was determined by the interferometric method for the temperature range 25° to 1,000° C. Single-crystal magnesium oxide and single-crystal aluminum oxide were used as reference materials. The bulk density and crystal form of the nonreference materials also were determined. The coefficients of linear expansion in the range 25° to 1,000° C were found to be 8.10 x 10-6 for yttria, 12.10 x 10-6 for ceria, 10.81 x 10'6 for samaria (monoclinic), 10.35 x 10-6 for europia (monoclinic), and 8.13 x 10-6 for dysprosia, each given in centimeters per centimeter per degree Centigrade. A detailed investigation of the interferometric technique for measuring thermal expansion in this temperature range was made. The interferometer was found to be a precise tool but only when adequate precautions were taken. These precautions are described.

Jan 1, 1963

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By G. S. Scott, W. J. Huff, G. W. Jones, R. E. Kennedy

"INTRODUCTION This report gives preliminary results of field and laboratory investigations made at the request of the War Production Board relative to causes that have occurred during the last 8 months in acetylene-generat72,r plants in shipyards on the Pacific coast.Six acetylene-generator explosions have occurred in four shipyards. These explosions killed five operators, injured six others, and extensive damage to the plants involved and curtailmnent of vital defense Although the occurrence of acetyiene-generator explosions in other section of the United States is not known, it appears, at least, that if such have occurred, they have caused only minor damage and no loss of lives.The use of acetylene in shipyards on the west coast has expanded tremendously during the past 2 years. These shipbuilding, companies erected aletylene-generatcr equipment, which was soon found to be entirely inadequate to meet the needs of their expanding acetylene requirements for welding, cutting, shrinking, and other purposes, and instances found it necessary to operate their equipment at rates greater than deemed consistent with safe operating practice."

May 1, 1944

By D. Harrington

Part III-B, presented in this circular, completes the series reviewing the literature on effects of breathing dusts with special reference to silicosis; it includes data on the status and cost of compensation for silicosis in the United States and several foreign countries and a summary and general conclusions covering the whole series. Parts I, II, and III-A of the series have been issued as Information Circulars 6935, 6840, 6948 , and 6957; Part I defines and classifies dusts, indicates sources of exposure, and describes the physiological effects of breathing dusts; Part II-A discusses the principal dust factors producing pulmonary pathology and methods of determination of dust in air; Part II-B presents data on the engineering and medical control in the prevention of dust diseases and general recommendations for their control in industry; and Part III-A deals with the economic and legal aspects of dust diseases in industry.

Jan 1, 1936

By Jack E. Fraley

In this Bureau of Mines study, sealants containing mineral wool, cement, etc, were sprayed through dry-process equipment that propels dry material pneumatically to the water-adding nozzle. Advantages over slurry applications include no mixing, no extensive cleanup, and freedom from hardened cement in equipment should power be lost. Sealants with large mineral wool nodules (>l-inch) were sprayable at rates to 900 square feet per hour for 1/2-inch thickness with little dust and smooth material flow through equipment, but they were weak for mine use, Materials containing small wool nodules (1/4-inch) were stronger but tended to plug lines because the nodules were inadequately separated in the shredder. Increasing the dedusting oil also increased line plugging by holding the nodules together in larger lumps. Best results were obtained using a 3/4-inch-nodule wool with cement binder, which provided both smooth flow through the machine and adequate strength.

Jan 1, 1977

By F. J. Wiebelt

Production of small tonnages of asbestos has been reported from 18 California counties; 16 additional counties have occurrences of asbestos. The counties in the northern part of California that have had a recorded production are: Alameda, Amador, Calaveras, Contra Costa, E1 Dorado, Napa, Nevada, Placer, Shasta, Siskiyou, Trinity, and Tuolumne. No deposit in the State has maintained consistent production. Serpentinized peridotites (potential chrysotile-bearing rocks) are widely distributed in the coast ranges, Klamath Mountains, and western foothills of the Sierra Nevada.

Jan 1, 1958

By J. A. Woolf, E. S. Leaver, N. K. Karchmer

"In the cyanidation of silver ore, the need of oxygen is well recognized. Various methods have been introduced for supplying the oxygen. In usual practice, air is the source of oxygen and the methods of application are mechanical.This article gives the results of touts made to show the rate of dissolution of silver from each of the common silver minerals in cyanide solution, under conditions similar to those used in the practical recovery of silver from its ores. The effect of oxygen in aiding the dissolution of the silver from each mineral is also shown by a comparison of the methods of supplying the oxygen. Oxidation by preliminary roasting (500°C.) of each mineral sample gives the maximum extraction of the silver by treatment with cyanide.Each silver mineral5 used in these experiments was as pure as could be obtained from the mineral dealer. In their natural occurrence, silver minerals are not usually free from mineral impurities. They are usually closely associated with other minerals often forming, a complex mixture. The form of crystallization, the proportions, and properties of the diluent that incases or has been dispersed with the silver mineral may decidedly affect the dissolution rate of the silver from each mineral. While the following results should aid in the cyanidation of silver ores, each ore should be studied from the basis of the form and condition of the silver that is to be recovered.All the tests reported in this article were made on synthetic samples, prepared by mixing the particular silver mineral with clean sea sand. Each mineral was ground in an agate mortar to pass 100-mesh before mixing with the sand which had previously been ground in a porcelain pebble mill to 100-mesh. Such proportions of each mineral and the sand were used as to give a head assay of approximately 20 ounces of silver per ton to the synthetic sample.Agitation was carried on in stoppered bottles approximately one-third full of pulp, method apparently supplied all the atmospheric oxygen that would be taken up by the solution under usual conditions, because tests conducted in open bottles did not show increased recovery,"

Jan 1, 1931

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

By F. G. Horino

The Bureau of Mines conducted compressive strength tests on model pillars of selected rock types with each pillar containing a critically oriented plane of weakness. The objective of these tests was to determine if a significant increase in the strength of the model pillar could be obtained by either (1) installing tensioned rock bolts through the pillar and normal to the plane of weakness, or (2) wrapping tensioned steel wire ropes around the pillar at uniformly spaced intervals along the pillar. Equations based on Coulomb's failure criterion are developed to predict uniaxial compressive strength of model pillars that are either rock-bolted or wire-roped. Laboratory compressive strength tests on unbolted and bolted model pillars of sandstone, marble, Indiana limestone, and oil shale containing a plane of weakness oriented at 45° showed that the bolted pillars are stronger than the unbolted pillars by 84, 31, 52, and 28 pct, respectively. Laboratory compres-sive strength tests on nonroped and roped model pillars of Texas limestone, sandstone, and granite containing planes of weakness showed that the roped pillars were stronger than the nonroped pillars by factors ranging from 1.01 to 2.41, depending upon the angle of the plane of weakness and the rock type. Rocks with a low Young's modulus benefited most by the wire-roping technique.

Jan 1, 1971

By R. S. Dean

The possibility of cheap electric power for a number of mining areas in this country has suggested to many the idea of electric smelting of nonferrous ores in small units at or near the mines. The electric smelting of nonferrous ores was tested fairly thoroughly 20 years ago by United States Bureau of Mines and by others, and the fact that it did not achieve continuing workable success in any instance is sufficient proof that it offered no advantages at that time.

Jan 1, 1937

By D. K. Steele

The domestic primary copper industry generates in excess of 600 million t of mining and mineral-processing waste annually. Most of the waste poses negligible environmental threat, but a small fraction, because of toxic or corrosive characteristics, may be subject to regulation under Subtitle C of the Resource Conservation and Recovery Act (RCRA) or other pertinent regulations. Among the wastes generated by various copper producers are flue dusts, slags, refinery-bleed solutions, and. acid-plant wastes. The U.S. Bureau of Mines (USBM) has researched methods to mitigate the environmental threat posed by copper-processing wastes while recovering valuable metals from these materials. Acid-leach processing of flue dusts has been demonstrated feasible along with sulfide treatment of liquid refinery wastes and acid-plant-bleed and gas-cleaning solutions to precipitate dissolved metals. In, addition, the feasibility of removing copper and molybdenum from slag, as well as stabilization of precipitated sulfide wastes by vitrification, have been investigated.

Jan 1, 2010

By T. F. Mitchell, Walter J. Long

"SUMMARYThis report is one of a series giving results of laboratory and pilot-plant investigations of the concentration of western manganese ores begun in December 1940. Data given summarize results of laboratory investigation of three samples of complex oxide manganese ores from the Madeline property, Lake View, and Victory claims, Clallam County (Olympic Peninsula), Wash. The samples represented an extremely intimate and complex association of manga¬nese oxide minerals with silica and iron.Owing to the complex nature of the ores, no effective concentration by ore-dressing methods was possible. No high-grade manganese concentrates were produced and the highest recovery at minimum accountable grade was only 55 percent on one of the ores tested.Since the Clallem County ores did not respond to ore-dressing methods, leaching processes were investigated, results of which are to be published in a separate report.INTRODUCTIONOre-beneficiation tests were conducted on three samples of manganese oxide ere from the Madeline, Lakeview, and Victory claims, Clallam County, Wash. The ores are extremely complex because of the unusually small size of manganese mineral particles, their mode of occurrence, and relationship to the gangue. None of the three ores was amenable to the production of high-grade manganese products by ore-dressing methods."

Dec 1, 1945

By Dean H. Ambrose

Using three-dimensional (3-0) graphics computing to evaluate new technologies for computer-assisted mining systems illustrates how these visual techniques can redefine the way researchers look at raw scientific data. The U.S. Bureau of Mines is using 3-D graphics computing to obtain cheaply, easily, and quickly information about the operation and design of current and proposed mechanical coal and metal-nonmetal mining systems. Bureau engineers developed a graphics simulator for a continuous miner that enables a realistic test for experimental software that controls the functions of a machine. Some of the specific simulated functions of the continuous miner are machine motion, appendage motion, machine position, and machine sensors. The simulator uses data files generated in the laboratory or mine using a computer-assisted mining machine. The data file contains information from a laser-based guidance system and a data acquisition system that records all control commands given to a computer-assisted mining machine. This report documents the first phase in developing the simulator and discusses simulator requirements, features of the initial simulator, and several examples of its application. During this endeavor, Bureau engineers discovered and appreciated the simulator's potential to assist their investigations of machine controls and navigation systems.

Jan 1, 1992

By C. Harry Benedict

This paper, describing the leaching practice at the Calumet and Hecla mills, Lake Linden, Mich., is one of a series on milling methods and costs being published by the United States Bureau of Mines. GENERAL DESCRIPTION The reclamation plant is located along the shores of Torch Lake at a slightly lower level than the concentrator itself. The entire location of the original concentrator, in connection with the present reclamation plant, has been ideal, lore particularly as the leaching and flotation departments are common to both units. After 15 years of operation and with the reclamation sands just a little more than half exhausted it would appear that the remaining life of the deposit could be worked by the present plan, without decided changes or renewals of plant or equipment.

Jan 1, 1930

By Barton K. Cross

The objectives of this effort were to: 1) Develop and validate start-of-shift operational inspection procedures to be used by operators of mobile, self-propelled equipment used in surface mining operations; 2) Evaluate user acceptance of the developed procedures; and 3) Recommend methods and media for presentation of the developed procedures to the user population. Mobile, self-propelled surface mine equipment requiring start-of-shift inspection was identified. Subsystems amenable to operational inspection were identified. The procedures addressing all safety critical subsystems on each equipment type were then developed and validated. The inspection procedures developed were those that could be performed largely from the operator's station. User acceptance was evaluated during on-site data collection visits to surface mines. Representatives of the user population reviewed the procedures and were then interviewed. Recommendations for the methods and media of presentation to the user population were developed from information obtained in: 1) Review and analysis of instructional technology literature applicable to this area; 2) On-site data collection; and 3) Analysis of the working environment and characteristics of the user population.

Jan 1, 1977

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954