Search Documents

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By H. E. Powell

The magnetic susceptibility, the geographical source, and associated minerals are given for 44 copper-, 26 lead-, and 19 zinc-bearing minerals. Of the 44 copper minerals/ all had a susceptibility of less than 15 X 10-6 cgs, and about 20 percent of them were diamagnetic. Of the 26 lead minerals, all had a susceptibility of less than 11 X 10-5 cgs, and almost half of them were diamagnetic. And, of the 19 zinc minerals, all except four had a susceptibility of less than 9 X 10-6 cgs, and about one-fourth of them were diamagnetic.

Jan 1, 1968

By E. C. Westman

Three-dimensional velocity tomograms were generated on a daily basis to image mining-induced changes to the overburden above a longwall mine. The hypothesis was that a coherent redistribution of seismic velocity, due to the development of high-stress zones, could be imaged at the mine scale. Seam depth was 360 m and source location depth varied from 100 to 1000 m. Sixteen geophones were distributed over a 600 by 600 m square area on the surface above the mine. More than 12,500 events were recorded over an 18 day period. The recorded seismicity provided input for the local-earthquake tomography code, SIMULPS. Eighteen tomograms were generated and high-velocity regions correlated well with high abutment stresses. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated. These results indicate that velocity tomography can be used to provide a better understanding of temporal changes within a rock mass, and can potentially be used to produce a better understanding of the mechanisms that lead to unanticipated ground failures.

Jan 1, 2008

By Richard L. Rains

In 1992, the Bureau of Mines evaluated mineral resources of the 34,043-hectare Caribou City and 41,943-hectare Stump Creek study areas in southeastern Idaho. No resources were delineated. The areas had been proposed for wilderness. Rocks underlying the study area are part of the Idaho-Wyoming Thrust Belt. At Caribou Mountain they have been intruded by diorite-monzodiorite. Where the intrusive rocks contact calcareous members of the thrust belt, skarn bodies have formed that host metal deposits. Gold, both placer and lode, occurs in the Caribou City area, and salt occurs in the Stump Creek area. Production records show 73.5 kg (2,363 ounces) of placer gold were produced; however, field studies indicate more than 2,000 kg (67,000 ounces) probably were recovered. Minor amounts of lode gold, silver, and copper were recovered from the hard rock mines. Production of salt from the Stump Creek study area in the 1860's was used by emigrants on the Oregon trail and also shipped to various mining districts for use in silver recovery. Oil and gas were drilled for, but all holes are plugged and abandoned. There are no current leases. Examined workings consisted of 25 adits, 3 shafts, 50 prospect pits, and extensive placer workings all in the northern tip of the Caribou City area, Current BLM records show 168 placer and 146 lode claims; 14 claims are patented.

Jan 1, 1993

By Travis Q. Lyday

The other South Pacific islands included in this chapter extend from Papua New Guinea, east of the Indonesian Province of Irian Jaya on the island of New Guinea, to Fiji, straddling the 180° meridian. A number of islands have been omitted from this chapter owing to the fact that their only mineral production remained insignificant to the economy of the respective country or territory. These islands include the French overseas territories of French Polynesia and Wallis and Futuna Islands; the independent states of Kiribati, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands; and the New Zealand dependency of Niue. The mineral production that did exist in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities used solely for domestic consumption. FIJI Fiji, an archipelago in Melanesia consisting of 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets to the larger mountainous, volcanic islands of Kadavu, Taveuni, Vanua Levu, and Viti Levu, straddles the 180° meridian about 1,800 kilometers south of the Equator. Fiji has been an independent member of the British Commonwealth of Nations since October 10, 1970.

Jan 1, 1988

This sheet explains your audiogram (hearing test) and gives some basic information about protecting your hearing. Keep it so you can refer to it later. What is an audiogram? • An audiogram is often called a “hearing test,” but there’s no pass or fail • It is a written record of your hearing levels • A series of audiograms can track changes in hearing over time • Your hearing threshold levels (the quietest sounds you can hear) are measured in decibels (dB) at different frequencies from low (500 Hz) to high (8000 Hz) Why should I get audiograms? • To measure your hearing ability • To identify hearing problems • To monitor success at maintaining your hearing • To see if noise exposure is affecting your hearing Do I have normal hearing? Compare your hearing threshold levels to this scale: -10 – 25dB Normal hearing 26 – 40 dB Mild loss 41 – 55 dB Moderate loss 56 – 70 dB Moderate/severe loss 71 – 90 dB Severe loss 91 – 100dB Profound loss [ ]

Jan 1, 2008

By William H. Schiffbauer, Timothy Lutz, Michael R. Yenchek

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) participated in an experiment to facilitate the remote control of dozers used on coal stockpiles. The experiment consisted of supplementing the normal sensory cues an operator requires to manipulate the dozer from a remote location. NIOSH provided and tested a vision systems intended to give the operator the ability to operate the dozer safely and efficiently from a remote position. This paper highlights the genesis of the experiment, identifies the contributions of Consol Energy and Caterpillar, and details the NIOSH efforts and successful test results. Keywords-remote-control; vision system; stockpiles; safety

By H. C. Verakis, M. L. Harris, M. J. Sapko, K. L. Cashdollar

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for the Philippines for the period from 1970 through 1981. The work was done through the Bureau of Mines, Minerals Availability Program, under Contract number J01225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) eimber and lumber, 6) fuel, 7) powder and balsting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By J. W. Miller

Depletion of coals most suitable for metallurgical fuel has made necessary a general survey of coking coal reserves in the United States. These investigations were begunn 1948 at the joint request of the Munitions Board, Department of Defense, and a number of coal companies. This report, which is one in a series, by counties, describes the preparation characteristics of the coals of Harlan County, Ky. From these data it is possible to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are chemically suitable under present standards for producing metallurgical coke, (b) Which coals require special and more intensive treatment in preparation than is now practiced; and (c) Which coals cannot be considered to be potential sources of metallurgical fuel regardless of preparation.

Jan 1, 1955

By Robert E. Wood

The temperature dependency of the low-density viscosity coefficients, ?°T, of helium and of nitrogen, 100° to 1,000° K, is correlated with empirical equations, and the temperature and composition dependencies of the low-density viscosity coefficients, ?°T, of helium-nitrogen mixtures are correlated with the Chapman-Enskog expressions by using the Lennard-Jones (6:12) potential function. The residual viscosity, ?T,P - ?°T (the difference between the viscosity of a compressed gas and the dilute gas at a given temperature), was found to be a function of the thermal pressure coefficient, (?P/?T)V, and two parameters, a and 1, which are characteristic of gas composition. The equation ?T, P = ?°T + a [(?P/?T)V]ß represented 1,340 higher pressure experimental viscosity values with a mean absolute deviation of 0.86 percent, and this equation was used to compute viscosities of the gaseous helium-nitrogen system for a range of temperatures and pressures including those encountered in Bureau of Mines helium purification processes and in a crude-helium conservation gas reservoir. Tabular viscosities for helium, nitrogen, and 13 helium-nitrogen mixtures are presented for 110 temperatures, 133° to 740' K, and 49 pressures in the range 1 to 240 atmospheres. The accuracy of the tabulated viscosities varies because correlation parameters were obtained from experimental data of unequal reliability. It is estimated that uncertainties in the computed viscosity values are ±5 percent for the region 325° to 740° K, ±2 percent for the region 183° to 325° K, and ±5 percent for temperatures below 183° K. The latter uncertainty may rise to y10 percent as critical conditions are approached.

Jan 1, 1970

By K. C. Dean

During the investigations of the occurrence of manganese in the Western United States, a Bureau of Mines examining engineer collected samples frame two properties in Beaver County, Utah. As the ores were too low in grade to be acceptable by manufacturers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The Steelville property is about 37 miles southwest of Frisco, Utah. The deposit is an example of manganese occurring as a replacement of limestone in a bedded vein or as layers in limestone associated with shale and rock decomposition products. The Susie Q deposit, about 33 miles southwest of Milford, Utah, is also a tabular replacement deposit in limestone, apparently of limited extent. Test work was done on representative samples of 2-ton lots obtained by the examining 'engineer from each of the properties mentioned.

Jan 1, 1951

By Ch. D. Taylor

Past studies with blowing face ventilation systems have shown that using a machine-mounted scrubber and water sprays can reduced methane levels at the face. The current research was conducted to determine how the sprays and scrubber interact to reduce methane levels, and what spray configurations provide the best face ventilation when used with a scrubber. Testing was conducted in a ventilation test gallery designed to simulate a full-scale mine entry. In the entry, a model mining machine, equipped with a simulated dust scrubber and water spray systems, was located at the face of a 6.1 m (20 ft) box cut. Face ventilation was provided by a blowing curtain located 12.2 m (40 ft) from the face. Methane released from a manifold at the face was measured at six locations near the face to compare the ventilation effectiveness of the spray systems while operating with and without the scrubber. Airflow movement across the face was affected by the spray configuration and scrubber operation. Average face concentrations were lowest when directed sprays were used with the scrubber. Varying the direction of the scrubber exhaust affected face methane levels.

By Gerald T. Homce, James C. Cawley

Arc flash generally refers to the dangerous exposure to thermal energy released by an arcing fault on an electrical power system, and in recent years, arc flash hazards have become a prominent safety issue in many industries. This problem however, has not been effectively addressed in the mining industry. MSHA data for the period 1990 through 2001 attributes 836 injuries to “non-contact electric arc burns”, making it the most common cause of electrical injury in mining. This paper presents results from several elements of a recent NIOSH study of arc flash hazards in mining, and provides information and recommendations that can help reduce these injuries. Characteristics of past arc flash injuries in mining are first outlined, such as the electrical components and work activities involved (based on MSHA data). This is followed by a review of important concepts and terminology needed to understand this hazard. Next, methods for identifying, measuring, and managing arc flash hazards on a power system are covered, with emphasis on recommendations found in NFPA 70E, Standard for Electrical Safety in the Workplace. Finally, results are presented from a detailed arc flash hazard analysis performed on a sample mine electrical power system using IEEE 1584-2004a, focusing on components and locations presenting severe hazards as well as engineering solutions for reducing the risk to personnel. Index terms – electrical arcing, electrical burns, mining, arc flash hazard analysis

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By G. M. Kintz

"Methods and costs of rock-dusting bituminous coal mines have been discussed in various publications by the United States Bureau of Mines and others.3 This paper discusses the present methods and cost of dusting at the Swastika mine of the St. Louis, Rocky Mountain and Pacific Co., Raton, N. M.In the Swastika mine the recommendations of the United States Bureau of Mines with regard to rock-dusting are followed at least as well as in any mine in the States of Wyoming, Colorado, and New Mexico. This mine is located at Swastika, N. M., approximately 4 miles west of the town of Raton and is in the Raton coal seam. The mine is rated as gassy and produces approximately 1,000 tons of coal per day.A mining system known as the ""room-and-pillar with cut-offs"" is used which results in recovery of nearly 100 per cent of the coal. The mine employs approximately 250 men.Ventilation is maintained by a Sirocco fan so arranged that the air current may be reversed and exhausting approximately 130,000 cubic feet of air per minute at 3 inches water gauge. This fan is supplemented by two auxiliary fans for emergency use. Three main entries penetrate the hill in a straight line for approximately 8,000 feet. The haulage is through the center entry, which is also used as the intake in conjunction with a two-compartment concrete-lined shaft located at the end of the entries. The main return for 3,000 feet inby the fan is 12 feet wide and 7 feet high. For this distance the ribs have been reinforced by a wall made of coke-breeze blocks plastered over with cement. Solid concrete blocks are used for the top row of blocks of the wall. Steel 10-inch I-beams spaced 40 inches apart center to center are supported on these solid blocks and thus support the roof. The next 1,000 feet inby has the same area, but the cement blocks extend to the roof, as no crosspieces are needed. The airways are kept clean and well rock-dusted.A rather unique system is used to handle gas feeders along the intake and haulage entries. There these feeders occur in the roof or where gas is apt to collect in high points along the haulage, tin funnels as large as 3 feet in diameter are placed near the roof. From these a 2-inch or other suitable-sized pipe is run into the return through the wall of the nearest break-through. A valve on this pipe line controls the amount of air pulled. These devices keep the high places clear of any gas, even when strong feeders are encountered.Fifteen-ton electric trolley locomotives are used on the main haulage and approximately 30 roller-bearing oars, each having a capacity of approximately 3,000 pounds of coal, compose a trip. All loaded tripe carry steel drags on the last car, and automatic derails are located at advantageous points throughout the mine.All loaded trips are thoroughly sprinkled on the sectional partings and at the main parting. The track is sprinkled every idle day, or if needed, every day; from a large tank mounted on a truck hauled by a motor. Neither nozzle nor spray is used, as these were unsatisfactory. The water leaves the tank. through a 11/2-inch valve and is permitted to flow on the road through a horizontal 11/2-inch T. Water is obtained from filling stations located throughout the mine. It is stated by the officials that the use of this method of sprinkling permits the entire haulage roadbed to be wetted down in two hours."

Mar 1, 1930

By P. Yant, R. R. Sayers, R. D. Lieitch

"PURPOSE OF INVESTIGATIONOf more than 300 bituminous mines examined by Crichton 5 and his assistants in connection with litigation in Indian Creek Valley, Payette County, Pa., only four were found to have alkaline water. That work and many observations from of the authors have shown the general prevalence or acid drainage from bituminous coal mines. In connection with investigations pertinent to coal-mine drainage that are being conducted by the United States Bureau of Mines, it was noted with considerable interest therefore, that a mine in the Thick Freeport bed about 20 miles north of Pittsburgh had no acid water in the workings, As it was thought that this condition might be common to all mines,this condition in this bed most of them were visited, samples of the outflow and from different parts of the mine inside were examined, and such general information as was available was gathered.ACKNOWLEDGMENTSThe authors acknowledge with thanks the courteous assistance of mine officials in connection with collecting the data for this paper, and of the analytical and coal laboratories of the Bureau of Mines for analyses."

Nov 1, 1932

By Jürgen F. Brune, Alex C. Smith, William D. Monaghan

One of the predominant causes of fires in underground coal mines is flame cutting and welding. These fires can lead to major events such as the explosion that occurred on January 22, 2003 in an airshaft being constructed at the McElroy mine. Six contractors were inside the shaft at the time of the explosion and the explosion fatally injured three and seriously injured three [MSHA 2003]. Understanding the root causes of these fires and explosions will help prevent these types of events from occurring in the future. Fires and explosions require fuel, oxygen and an ignition source (heat). These three items are referred to as a fire triangle. The control of these three items in flame cutting and welding operations is required to prevent fires and or explosions. United States Department of Labor, Mine Safety and Health Administration (MSHA) Reports of Investigation (ROI), MSHA Mine Accident, Injury, and Illness Reports, and the MSHA Mining Industry Accident, Injuries Employment, and Production Data Base were analyzed and interviews and observations with mine workers and welders were conducted to determine the root causes of coal mine fires and explosions caused by flame cutting and welding operations. This paper will discuss the root causes and potential means to reduce the number of fires and resulting fatalities and injuries caused by or due to flame cutting and welding.

By G. L. Neumann

Owing to the need for additional sources of supply of both zinc and lead following World War II, the Bureau of Mines investigated many abandoned lead-zinc mines in the eastern United States. A series of shallow veins in south-western St. Lawrence County has long been a subject of speculation. These veins, which average about 4 feet in width and cut across the bedding of the country rock at right angles, are filled with calcite-carrying galena and sphalerite. The deposits have been worked sporadically during the last 115 years. From 1837 to 1852 the Coal Hill, the North, and the Victoria mines near the village of Rossie were at their peak of activity. Other calcite veins were prospected and a small production was realized. The Bureau of Mines began diamond drilling May 1, 1950, under the general supervision of McHenry Mosier, chief, Mining Branch, Bureau of Mines, Region VIII, and under the immediate supervision of the author) who was project engineer, following the preliminary examination by Robert S. Sanford. A total of 3,870.2 feet was drilled in 18 holes on four of the numerous deposits scattered over Macomb and Rossie townships. Drilling was completed September 21, 1950.

Jan 1, 1952

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Ohio County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of-coal in place, are estimated at 365 million short tons as of January 1, 1954. Of this total, 356 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955