Search Documents

By Paul Ross, Harry Burchett, Lou Case, Calvin J. Konya

"The Cumberland River in Harlan, Kentucky has flooded the town for numerous years. TheU.S. Army Corps of Engineers funded a project to divert the river. The project consisted oftunneling through a mountain to divert the river. The approaches to the tunnels requiredcontrolled blasting to create noses to help channel the water and debris into the tunnels.The geologic structure was such that conventional presplitting techniques were notproducing the desired results and were causing severe backbreak. Replacement of the rocknoses with concrete would cost about a million dollars; and therefore it was important tosave them if at all possible. Blasting techniques were developed which allowed the projectto be successfully completed. This paper will discuss the case history of the controlledblasting procedures."

Jan 1, 1993

By Raphael Trousselle, William Reisz

The blasting industry is now well into its second decade of commercial use of electronic detonators. As an increasing number of blasters are introduced to the technology, the benefits are becoming more widely monitored and accepted in many surface blasting operations. However, their use in underground applications is not yet as widely established. This is primarily due to the distinct cost dynamics and processes associated with underground lasting.

Jan 1, 2012

By Lee W. Saperstien

Section 709 of Public Law 95-87, "Surface Mining Control and Reclamation Act of 1977," requests the National Academy of Sciences to determine if the standards of the act are applicable to minerals other than coal. The Academy has established the Committee on Surface Mining and Reclamation to respond to this charge. The committee is, itself, organized to be responsive to the varieties of minerals, environments, mining systems, and locations that are representative of U.S. mining systems. It is not the charge of the committee to write trial legislation, but to indicate whether or not technology, extant or proposed, is available to meet the standards of the law, and at what cost. It is within this set of conditions that the committee will examine blasting.

Jan 1, 1979

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

By Jan Westberg, Roger Holmberg, Bernt Larsson

Over the last couple of decades there has been an increased demand from the market for precision detonators, partly because of a need for better blasting results and partly because of a need for better vibration control. Today's detonators have a pyrotechnical delay element which gives a relatively high time scatter, increasing with the length of the delay time.

Jan 1, 1988

By Allan King

Ammonium Nitrate (AN) is most commonly encountered as either a prilled solid or a highly concentrated aqueous solution, with or without organic ( e.g amine) nitrates. Under certain conditions of fire exposure involving prilled or solid AN, the molten state can be formed. The shock sensitivity of the molten material at temperatures greater than 220 Celsius has been found to be much higher than that of the prilled or solid form. Molten AN can be a precursor to events leading up to explosion of a bulk prill storage pile as a result of fire exposure. The explosion hazards presented by molten AN are a function of two factors; 1) its shock sensitivity and the deflagration to detonation ( DDT ) properties of the molten material, and: 2) the ability of large masses of unfueled prilled AN to be initiated and detonate. This paper presents the results of tests designed to determine the shock initiation and DDT properties of the solid ( prilled ) and molten AN.

Jan 1, 2008

By John T. Watson, Jim Bailey

Increasing public awareness is probably the single most important challenge faced by any blasting contractor today. This increased awareness usually results in an outcry for tighter regulations and restrictions on those in the blasting industry. Those affected do not often understand the dynamics of blasting and are simply fearful of the unknown. This reaction very often results in more regulations and restrictions which frequently fail to address the real problems.

Jan 1, 1990

By Tapan Goswami

The main objective of the blasting phase in a coal mining operation is to maximise the coal recovery. However, coal loss due to blasting is a serious problem. The Australian Coal Association Research Programme (ACARP) reported in 2011 that in Australia one in every ten coal mines is completely wasted due to such losses. Coal is either lost in the spoil, largely due to the blasting operation or becomes diluted and cannot be recovered entirely. The major coal loss mechanisms include losses from the coal seam roof, the floor, the front edge and from dilution. Coal damage and loss mechanisms during cast blasting that have been observed by various authors include: •Excessive cast dragging the coal edge in the cast direction. Movements of this nature are oftenassociated with the formation of trenches. •Spatial movement of overburden where rock shears and moves in a plane above the coal seam,which damages and dilutes the coal. •Rock falling over the coal during the blast often producing indentations in the exposed coal. •The inappropriate use of bulk and initiating explosives that often results in coal damage. •Insufficient stand-off distances from the coal. The Australian coal mining industry has gone a long way towards addressing the coal loss issues since 2011: almost all operations now deploy touch-coal drilling and sporadically use gamma logging for loading overburden. A study was conducted to compare the effectiveness of touch-coal information in which some touch-coal blastholes were drilled on a fixed or random pattern. In another study, some blastholes were drilled to the touch-coal, gamma-logged and mapped to determine stand-off distances. It was found that the coal roof surface created by gamma-logged holes was the most effective option for minimising coal loss. As a result, a variable stand-off distance was found to be the key to minimising losses. This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

By Tapan Goswami

This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

Feb 1, 2020

By Kurt B. Oakes, Brian M. Fortelka

Unimin Corporation operates an underground Silica Sand mine at Guion, AR located in North Central Arkansas. The Silica Sand deposit at Guion is part of the St. Peter Sandstone Formation, which is overlain by a competent dolomitic limestone from the Joachim formation, acting as the roof directly above. Both the St. Peter and the Joachirn Formations are of Middle Ordovician age.

Jan 1, 1999

By Joel Warneke, Cristian Caceres, Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2008

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009

By Sandor Nagy

The Explosive and Blasting Department of the Hungarian Mining Research Institute is responsible for the research and development of industrial applications of explosives. Appropriate explosives technology is developed for each application, including the explosive demolition of structures, which belongs within our charge.

Jan 1, 1977

By Kurt Oakes, John Williams

Placer Dome, US operates the Bald Mountain Mine. The Bald Mountain Mine is a surface operation located in remote northwestern White Pine County in east-central Nevada, approximately midway between Elko and Ely. The mine is in the Newark Valley along the southwestern flank of Bald Mountain a part of the Ruby Mountain range, at an approximate elevation of 7,500 ft (2,286 m). The geology at the Bald Mountain Mine is highly altered, both mineralogically, and structurally. Highwall stability and control have long been an issue at the operation, due largely to the varying geologic conditions. In some blasts as many as seven distinct geologic unconformities exist. These unconformities affect both final high wall integrities, as well as blast fragmentation characteristics. A 60 million ton (54.5 million tonnes) layback expansion of the existing “Top Pit” as well as development of a new satellite pit, “Sage Flats”, is being undertaken. Design final highwall pit slopes have been steepened from the traditional 47º to 55º in order to reduce overall ore-to-waste ratios, thereby improving economic viability for the expansion over the 4.5 year life of the project. With the increased usage of electronic detonators throughout the mining industry, mine operations staff, as well as representatives from the mines explosive supplier felt that an evaluation program incorporating electronic detonators would be warranted. The areas of focus for this evaluation would be resultant highwall pre-split integrities, peak particle velocity measurements (both near field and far field), frequency measurements, loader productivity, and visual interpretation of the results. The mine incorporates 25 ft (7.6 m) benches and uses separate trim blasts in conjunction with production blasts in order to reduce blast effects along final highwalls. Hole diameters in production blasts are 7? ” (200 mm). Typical production blast patterns are 18 ft x 18 ft (5.5 m x 5.5 m), drilled in a square pattern configuration. Shot sizes vary greatly, ranging from 200 holes to as many as 800. Bulk low percentage ANFO/emulsion blends are utilized as the redominant blasting agent. Non-electric dual delay detonators (25 ms/500 ms), with non-electric surface delays are the initiation system utilized in production blasts. Typical production blast design

Jan 1, 2004

By Frank Huber, Ed Fulop, Neil Singh, Ron Elliott, Blair Gohl, Lewis Clarke

This paper covers the successful application of explosive compaction technology for the densification of the foundation soils for the seismic upgrade of the Seymour Falls Dam, Vancouver, BC. The original earthfill embankment constructed during 1958 to 1961 was upgraded in 2004 to 2007 to withstand the effects of a maximum credible earthquake. This paper provides general background information on the theory of the explosive compaction of soils, history of use, geology of the site, project constraints, explosives selection, blast designs, instrumentation used, problems encountered and solutions implemented, and the results achieved.

Jan 1, 2009

By M R. Hettigner, J Nawrocki, C E. Johnson, P G. Cahill

This study evaluates the effects of both short inter-hole and intra-hole delay times on rock fragmentation and throw. Full-scale test blasts were analyzed at a granite quarry in Talbotton, GA. This analysis provides a representative understanding of timing effects on fragmentation in the field, different from previous lab scale studies that negate the effect of geology. Inter-hole delay times between 0 ms and 25 ms were tested on a series of 4 bench blasts and subsequently examined using photographic fragmentation analysis methods.

Jan 1, 2017

By Paul Worsey, Braden Lusk, Seokbin Lim

This paper discusses the theory and experiment involved in the discovery of the mechanisms of Linear Shaped Charges, which are much different from those for Conical Shaped Charges. Linear Shaped Charges (LSC) have been assumed to function in the same manner as Conical Shaped Charges (CSC) in the published literature on the subject. Much work has been done on CSC for military purposes, but there is limited information about the mechanics of LSC. Previous theories have cited the formation of a Monroe Jet as the dominant process. The Monroe Effect describes what happens to a target below the charge following detonation of the charge, and prescribes a fluid jet process for penetration. The fluid jet comprised of the liner material is the cutting device in CSC and has been extensively studied. Recent work at the University of Missouri at Rolla (UMR) cutting concrete with LSC has surprisingly shown that there is not a fluid jet process in LSC. After completing several reinforced concrete penetration tests, minimally deformed copper blades were found in the debris. Initially, the blades were suspected to be misfires or malfunctioned charge remnants. However, results were good and blades were found after every single test. Upon closer inspection, the ribbons were found to be folded copper and they were suspected to be the bottom liner of the LSC. A test series was conducted to verify the new theory by experiment.

Jan 1, 2005

By CVB Cunningham

"The Kuz-Ram model as originally proposed included an error in assuming that the mean fragmentsize predicted by Kuznetsov’s equation was actually the 50% passing size. In 2003 Spathis began discussions on this issue and recommended correcting the equation. The correction produced more fines in the predicted fragmentation, which had been a criticism of some users of the original model. Ouchterlony subsequently showed that the error had, if anything been beneficial, and that the Swebrec function adequately covered the fines. This author shows that the Spathis correction does not assist the fines correction in examples examined, but tends to underestimate coarser fractions. An intrinsic problem of communication between academics and engineers is a root of misunderstanding on both sides, and requires patience by both parties to enable value to arise."

Jan 1, 2016

By Paul Worsey, Gillian Worsey

Description of Project:The basic blasting class underground lab at the Missouri S&T experimental mine in Rolla, o., shows the students how to drill, set up, load, and shoot a shot underground. In this case the shot was part of a new ramp to a second level.

Jan 1, 2014

By Daniel Roy, Chris J. Preston, Ron J. Elliott

This paper discusses the use of pressure transducers in water filled boreholes in conjunction with surface mounted geophones to gather field data for in-situ dynamic rock properties determinations. A high speed collector is used to capture the data in the field. The calculated P and S wave velocities and rock density measurements are used as input into the Blastcalc program where the values of Young`s Modulus and Poissons Ratio are calculated. The rock properties information is used along with geological structural data and explosives properties in a 3-D blast modelling program to calculate predicted fragmentation distribution and other blast performance criteria based on the proposed blast design.

Jan 1, 1996