Search Documents

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

By M. R. Garmsiri

With the environmental issues and water recycling becoming more significant, the development of deep cone thickeners has improved the efficiency of thickening. While deep cones performance is dependent on many factors, the sensitivity of an industrial thickener to each variable factor has not been determined. In this work, four industrial deep cone thickeners, which are used on tailings stream in Shahrebabak Copper Complex, were monitored for a year to analyze the effectiveness of different factors affecting the performance. Feed flow rate, fine fraction of the feed, solids concentration, flocculant dosage and concentration, solids density, pH, temperature and bed height were the factors investigated on the basis of partial R2 and partial correlation. Results indicated that, with positive effect, feed slurry dilution affected the dewatering efficiency most sensitively. With a negative effect, the sensitivity of dewatering efficiency of deep cone thickeners to flocculant dosage was negligible. While, decreasing flocculant solution concentration had a considerable positive effect.

Sep 1, 2012

By D. W. Feng

Thiosulfate leaching has been considered as the most promising alternative to cyanidation for the recovery of gold from ores. The chemistry of the ammonia-thiosulfate-copper system is complicated due to the simultaneous presence of complexing ligands such as ammonia and thiosulfate, the Cu(II)-CU(I) redox couple and the stability of thiosulfate in solution. However, acceptable gold leaching rates can be achieved by maintaining suitable concentrations of thiosulfate, ammonia, cop-per and oxygen in the leach solution. The leaching of gold in thiosulfate solution is an electrochemical reaction involving the oxidation of gold to gold thiosulfate and the reduction of Cu(II) to Cu(I). Previous studies have shown that the reaction rate of gold was much higher in the presence of am-monia thiosulfate than corresponding sodium thiosulfate. This indicates that cations may affect the anodic oxidation of gold in thiosulfate solution. The present study utilises electrochemical tech-niques to study the anodic oxidation of gold in thiosulfate medium in the presence of the different alkali metal and alkaline earth metal ions. It has been shown that the presence of the heavier cations such as potassium, calcium, and caesium enhance the oxidation of gold in thiosulfate solution. Leaching tests also indicated the improved recovery of gold from a sulfide ore with the addition of heavier cations. XPS results demonstrated that the binding energy for gold shifted to lower values in the presence of the heavier cations, indicating the ready formation of ion-pair with gold thiosulfate at the gold surface during adsorption.

Jan 1, 2014

By Peter Ay, Florian Logsch, Satyanarayana Narra

"The traditional lignin separation process from the precipitated suspension creates severe filtration problems by plugging of the filter medium due to the small particle size (20 to 60 µm) of the suspended lignins. The plugging causes further problems in the successive processing of the filter cake. A new lignin separation process has been developed at the Brandenburg University of Technology (BTU) Cottbus as a part of the Research and Development and Demonstration (R & D & D) project "LignoBioFuel". The new developed process separates lignin in the form of granules with diameters ranging from 100 µm to 300 µm. The restrainment of the granule’s size in their successive treatments is expected to result in higher filtration efficiencies and reduction in plugging of filter mediums. To evaluate the filtration efficiency, the filtration resistance of the produced granules as well as the conventional suspensions has been investigated. The results show that there is a 60 to 80 % filtration efficiency increase and around 60 % reduction in plugging of filter mediums with the lignin granules in comparison to the conventional suspensions. Furthermore the successive processing of lignin granules was easier due to their porous structures removing the impurities such as adherent acids and salts. The purity of the separated lignin was measured with their sulphur (reduced from 7 % to 2.7 %) and ash (reduced from 46 % to 0.5 %) contents. The newly developed process has displayed better results in comparison to that of the conventional process. The new process displays high potentials in optimizing and improving the present state of the art treatments and is promising several ecological, economical and environmental improvements."

Jan 1, 2014

By M. C. Harris

"In the flotation process the contact angle is an important indicator of the hydrophobicity of a mineral particle. There is considerable literature showing that the contact angle increases when the chain length of the alkyl group associated with the collector molecule used to render the valuable mineral particle hydrophobic increases. The extent to which an alkyl group interacts with surrounding water molecules is quantified thermodynamically by the excess Gibbs energy. In the present paper it is shown that there exists generally a strong linear relationship between the excess Gibbs energy of the alkyl group associated with the collector and the contact angle. The structure-activity of such alkyl groups is in turn related to the total surface area, molecular volume, the molar volume, molecular weight of the functional groups in the molecule and interaction energies. It is proposed that the demonstrated relationship is indicative of the role which the alkyl group component of the collector, which is attached to the mineral particle, plays in increasing the extent to which water molecules at the surface of the mineral are rejected from the surface thus increasing the contact angle. The relationship between excess Gibbs energy and surface tension is further explored with a view to relating the observations quantitatively to the parameters in the Young equation.INTRODUCTIONThe issue of wettability of materials is of great importance to many industrial applications. Wettability studies usually involve the measurement of contact angles which indicate the degree of wetting when a solid and liquid interact. As is well known the contact angle (O) is the angle between planes tangent to the surfaces of the solid and the liquid at the wetting perimeter which is the zone where the air, water and solid phase merge. When the air bubble attaches to the solid surface there is an increase in the air/solid interface area and a decrease in the solid/water interface area. For attachment to occur the cosine of the contact angle should be less than 1 and this will be promoted if the interfacial surface tension between the air and the solid (? SV) is low. Classically the relationship between these parameters has been expressed through the Young equation (1) for a perfectly flat surface:"

Jan 1, 2018

By Q. W. Jiang

This paper presents a new process for producing industrial magnesium sulphate using waste water from titanium white plant and magnesium oxide from calcinations of magnesite ore as raw materials. With the laboratory experimental equipment, the waste liquid and magnesium dioxide react effectively at ambient temperature and under atmosphere pressure. Via the press filter, a clear liquid predominately containing magnesium sulphate is obtained. It is further evaporated and crystallized by cooling, separated by centrifuge and dried. Consequently a high quality of industrial magnesium sulphate is achieved as the final product. In the course of process, as the majority of valuable component (SO42-) is recovered in the final product, most of impurities from waste acid is being removed into the by- product. With the simple operational process, it is possible for titanium dioxide plant to resolve the environmental problem completely and benefit from the industrial magnesium sulphate product as well. The filter cakes containing valuable elements such as Mg, S, Fe, Mn, V, Ti are by-product proposed to be used for manufacture of agriculture fertilizer particularly for peanut planting.

Jan 1, 2014

By L. Y. Zhang

The metallic sulphides in Jinchuan Mine are relative friable and the gangue minerals suffer of wide secondary change, the overgrinding of metallic sulphides and sliming of gangue minerals are the main cause that makes the mineral separation indexes difficult to improve. So changing the process of grinding, and classification, and optimizing the particle size distribution of grinding product is the key improving the separation performance of Jinchuan nickel and copper ore.

Jan 1, 2014

By A. I. Arol

Bentonite is an important industrial mineral with very wide application areas. Its unique colloidal, swelling, thickening and adsorption properties make it a useful agent in drilling, metal casting, and iron ore pelletizing, environmental, food, cosmetics, pharmaceuticals and many more industries. Because of its swelling property, bentonite suspensions can only be prepared at rather low solid coentrations, i.e. 8-10%. In order to process bentonite in slurries with high solid content, it was thought that a non-polar organic solvent, instead of water, can be used. Not only large amounts of bentonite can be dispersed in organic solvents but also the solvents may be regenerated. The bentonite obtained through such a process must either equal or better properties than those of untreated bentonite. In this study, the effect of organic solvents such as acetone, methyl-ethyl ketone and n-haxane on the main properties of bentonite, such as water adsorption and rheology, was investigated. It was found that bentonite can be dispersed in the mentioned organics in large quantities with no loss of quality. Keywords: bentonite, montmorillonite, water adsorption, industrial minerals

Sep 1, 2012

By Aidan Giblett, Karen McCaffery, Robert Dunne

"A worldwide decline in competency levels of practicing metallurgists over recent decades has become clearly evident and is a common topic of discussion among senior practitioners and professional associations. The associated impacts on the industry are material and include operational inefficiencies, missed optimisation opportunities and suboptimal new plant designs. There are many contributing factors to this condition. Decrease in competency is particularly evident both in regions where imbalance between supply and demand has led to a general reduction in experience levels for comparable roles over time and in emerging regions where a rapid rise in demand for practitioners has occurred in conjunction with rapid economic development and industrialization. The context, depth and breadth of education curricula and levels vary with location such that solutions to the technical competency dilemma may need to be developed specifically for each region with these influences in mind. Delivering, demonstrating and maintaining competencies are a critical requirement of undergraduate training and ongoing professional development. Other factors such as generational and cultural characteristics and expectations, political influences, role requirements and employment reward and recognition systems all play a critical role in determining if core competencies can be effectively developed, applied and subsequently maintained. This paper reviews factors impacting and some common approaches to competency development. The authors’ experiences in the management of professional development efforts within the global industry are reviewed and a blueprint proposed to address industry requirements in this area."

Jan 1, 2014

By R. Singh

The paper presents the results of characterization and beneficiation studies carried out on a lean grade tungsten ore sample from Degana, India. Basically, three different routes, involving gravity separation, magnetic separation, and froth flotation were studied for concentration of the sample by physical and physico-chemical methods. Considering the low recovery by physical methods, efforts were put in to produce a tungsten concentrate by physical methods suitable for subsequent hydrometallurgical recovery of tungsten as ammonium para-tungstate. This strategy proved quite helpful in minimizing the losses of tungsten in tailings. Based upon these studies a novel integrated technological process flow-sheet was developed for the exploitation of lean grade tungsten ore deposit of Degana, India. Keywords: lean tungsten ore, characterization, beneficiation, gravity and magnetic separation, hydrometallurgical extraction, integrated process route

Sep 1, 2012

By Weiran Zuo, Emmy Manlapig, Fengnian Shi

The effect of metalliferous grains on electrical comminution efficiency was investigated by comparative experiments using natural rocks and synthetic samples. The result indicated that the existence of metalliferous grains affects the breakage probability and product size distribution of electrical comminution. On average, metalliferous grains increased the breakage probability of particle in the first pulse discharge by 55% and generated finer product at the coarse end. As a result, particles with metalliferous grains exhibited higher energy efficiency than that without metalliferous grain in electrical comminution. A positive linear relation between product fineness and specific energy in electrical comminution was observed. With the assistance of numerical simulation on the electrical field distribution of ore particle, the role of metalliferous grains in electrical comminution is confirmed and the mechanism of metalliferous grains effect is elucidated. Understanding of the effect of metalliferous grains on electrical comminution is important to evaluate the feasibility of applying electrical comminution to ores with different mineral composition, and to understand the breakage behavior in electrical comminution.

Jan 1, 2014

By M. R. Tavakoli Mohammadi

Novel solvent extraction technologies in recent decades have made attempts to show the problems in applying this method for dilute solutions and find appropriate solutions to overcome them. Improving the equipments performance used in this method for dilute solutions, cause development of usable resources and reduction of operational costs. Furthermore, appropriate conditions provide for using dilute solutions produced in various industries as a new source of valuable elements. Thus, this proposal can be a very good solution for treatment of these solutions and reduce the environmental impacts associated with them. The purpose of this study is to introduce a new method of Column Floto Extraction (CFE), which has been invented in this regard. In this method, using spargers similar to Jameson cell downcomer in floatation process, the organic phase bubble dispersion has been used instead of its drop dispersion in aqueous phase for the two-phase mixture operation. This operation mode has caused a higher extraction percentage of solute in high aqueous to organic ratios due to enhancement of contact area. In this study, in addition to explaining the advantages and features of this method, we have dealt with its design and performance mode.

Sep 1, 2012

By Haghi. Hamed, Javad Vazifeh Mehrabani, Mehdi Sedigh

In this investigation, the possibility of physical separation methods such as attrition scrubbing, hydro-cycloning and also reverse flotation were investigated for silica and calcite removal from relatively low grade kaolin. The head sample was provided by the Iran China Clay Company and the major oxides contained in the head sample were Al2O3, SiO2, CaO and Fe2O3 with grades of 15.07%, 71.05%, 4.35% and 0.52% respectively. The liberation degree of calcite and iron impurities from kaolin particles were over 80% for particles finer than 210µm and 53µm respectively. Attrition scrubbing tests were carried out with scrubber cell of the conventional Denver flotation cell model D-12. Laboratory scale hydro cyclone was applied for the beneficiation of kaolin. Attrition scrubbing tests with control screen of 106µm did not achieve the desirable yield for purification of this kaolin sample, but hydro cyclone experiments resulted in better results. Hydro cyclone with 2.54 cm diameter used and the only variable was the cyclone inlet pressure ranging from 68.65kPa to 98.07kPa. The best inlet pressure was found to be 68.65kPa. Based on the optimized condition, Al2O3 and CaO amount in the hydro-cyclone overflow was 23% and 1.47% respectively. However weight recovery of the overflow in each cyclone experiment was less than 30% and multi stages of hydro-cyclones would have to be applied for higher weight recovery and better yield. All of the flotation tests were carried out in the conventional Denver flotation cell model D-12. Reverse floatation tests for calcite removal were carried out under alkali pH based on full factorial design of variables in 2 levels including one center point. The three parameters tested were collector dosage (gr/ton), pH and depressant dosage (gr/ton). The collected data from flotation tests were analyzed and optimized collector and depressant dosage were 1000 gr/ton and optimized pH was 8.5. Under the above mentioned conditions, calcite removal was about 75% and CaO content in the final product was reduced from 4.35% to 1.33%. However calcite removal will increase to more than 83% if the feed particle size in flotation tests is reduced from 210µm to finer than 53µm. Finally after optimization, the best working condition and possible flow sheet were developed.

Jan 1, 2014

By A. F. Usov

The paper is concerned with an analysis of the experience gained in development of special electro-technical installations applied in electric-pulse destruction of materials. A principle scheme of an electric electric-pulse installation is given, and electric circuit variants of its blocks made on various element bases are discussed. Also assessed are some ideas to further improve the technical and economic characteristics of the equipment.

Jan 1, 2014

By W. Fander, Zhonghan Zhang, T. Choo, J. Enraght-Moony

"This paper describes the mineralogical and metallurgical procedures used to determine the recovery and concentrate grade of heavy oxide minerals occurring in lode deposits. The data produced also provide vital information to the processing engineers, which allows them to develop the most suitable flow sheet for that particular heavy mineral, here called an Economic Oxide Mineral (EOM). It demonstrates how results are interpreted to ensure that the proper process is used at each treatment stage to optimise recovery and to produce the most suitable concentrate at that point. Reference is made to some of the current equipment and techniques that can be used to process EOMs. The paper shows that when assessing the economic potential of a new ore body, or existing ore treatment plant, ore characterisation (OC) is necessary. This is especially true for EOMs such as cassiterite (SnO2), wolframite ((Fe, Mn, WO4,) pyrochlore ((Na,Ca)2Nb2O6(OH,F)), and tantalite (MnTa2O6) where often what seem to be small changes in ore types can have major effects on recovery and concentrate grade. Due to advances in flotation technology scheelite (CaWO4) in some deposits can be less vulnerable to OC variability than other EOM’s. Thorough mineralogical examination is shown to be the fundamental basis of correctly undertaking OC. This is because mineralogical analysis identifies each of the steps required to ensure that all ore types and zones are recognised, and differences explained, and shows the benefit in using reference samples to compare differences in the ores. The OC methods used for EOMs containing metals such as tantalum, tin, tungsten and niobium are similar; if two or more of these EOMs occur in one deposit as separate minerals, then OC will show when and how these minerals should be separated. The OC techniques described for EOMs can also be tailored for other heavy minerals, precious metals and graphite."

Jan 1, 2014

By A. Ekrem Yüce, Gülay Bulut, Feridun Boylu, Vecihi Gürkan, Istanbul Technical University, H. MustafaTarkan

"Nickel sulphide ores subjected to this investigation were taken from Orhaneli district where widespread chromite mineralisation can be occurred. Significant amounts of magnetite and chromite have been existed in the ore together with sulphide and oxide type nickel minerals. Ore sample is constituted about 70% magnetite, 15% sulphide minerals, 5% chromite and iron oxides as well as 10% gangue minerals.According to the chemical analysis results, the representative ore sample contains 1.32% Ni, 10.8% SiO2, 78.4% Fe2O3, 1.3 g/t Ag and 1.0 g/t Au. Mineralogical examinations showed that pentlandite (Fe, Ni)9S8, violarite (Ni, Fe)3S4, millerite NiS and asbolane (Co, Ni)MnO2.(OH)2.1-2H2O were the main nickel minerals and magnetite, chromite, chromium spinals, pyrite, pyrhotite, chalcopyrite, cubanite, goethite, hematite, limonite, rutile, chlorite, talc and serpentine group minerals as associated minerals.The aim of this investigation was to produce valuable nickel concentrates by using gravity separation, magnetic separation and flotation methods. As a results of laboratory scale studies, alternative flow sheets for the production of nickel sulphide concentrate were developed. The related experimental results are given in Table 1."

Jan 1, 2003

By Sergio Castro, Janusz Laskowski

In the flotation in highly concentrated electrolyte solutions not only ionic strength but also chemical composition, flotation pH and mineral properties play an important role. As a result an improvement or depression may be observed. A strong improvement in the floatability of hydrophobic bituminous coals and other inherently hydrophobic minerals is characteristic for the "salt flotation process", which is carried out in concentrated electrolyte solutions at natural pH and without addition of any flotation reagents. However, pH is a key factor when saline and hipersaline waters with hydrolyzing metallic ions are used as process water. In the case of flotation of Cu-Mo sulfide ores in seawater, molybdenite is strongly depressed by the Mg2+ hydrolysis products when pH is raised to depress pyrite. Process water with a high content of Mg2+ and Ca2+ ions, and this also includes seawater, have deleterious effect on the anionic flotation of industrial minerals with fatty acids. The flotation of potash ores is carried out in NaCl-KCl saturated brine (6-7 mole/L of NaCl and KCl) with the use of long-chain amines. Such a high electrolyte concentration changes dramatically the amine Krafft point making the collector insoluble in brine; its mode of action entirely differs from that in conventional flotation processes.

Jan 1, 2014

By C. Kleine

Coal sorting with an x-ray-transmission (XRT) sensor has experienced a lot of development since first described by Jekinson et.al. in 1974. Powerful computers and increasingly sensitive X-ray scintillation counters enabled the development of high-performance sensor-based sorting machines. The first industrial installation of a belt-type XRT-sorting for coal is in operation since 2004. It is upgrading high quality coal from 1% ash to 0.7% ash for cathode production. In comparison to the high quality coal which is treated with a belt-type sorter, the chute type sorter has been successfully optimized for high volume coal treatment of lower quality coals. This project was funded by the German Environmental Fund (Project Nr.244444). In cooperation with the RWTH Aachen University and Isambane Processing, CommodasUltrasort(now Tomra Sorting Solutions) conducted extensive pilot test work under production conditions in 2010 for the destoning of power station coal at Arnot Power Station in South Africa. The experience gained during this pilot test phase led to an optimized, redesigned PRO Secondary XRT Chute sorter which is now in operation at a South African coal mine. This flexible semi-mobile modular destoning plant is treating a size range of -120 mm +30 mm at a throughput of 150 tph. The implementation of this plant not only reduces the ash content, abrasiveness index and sulfur content significantly, but also reduces royalties, water treatment and transport costs.

Sep 1, 2012

By T. Shumba

The solvent extraction section of an old Uranium Plant in the Vaal River region produced a sub-stance called Crud (Chalk River Unidentified Deposit) that formed within the aqueous/organic interface of the settler of the solvent extraction circuit. The crud was deposited together with gold tailings to the tailings dam many years ago. Previous research done on the crud confirmed that ex-posed crud leaches Mn and Ni at concentrations that are well above their acceptable risk limits as well as Zn that leaches at concentrations that are slightly lower than its acceptable risk limit. Soil washing and bioremediation technologies were employed to treat the contaminated soil. Various laboratory test work and the pilot scale studies were conducted in parallel with each other and the results of the laboratory studies were used to determine critical parameters. Four lixiviants, i.e. sulphuric acid, acetic acid, oxalic acid and ethylene diamine acetic acid were tested at three concentration levels i.e. 0.001M, 0.0001M and 0.00001M, respectively. Column tests showed that the leaching of the heavy metals increases as the soil porosity increases. Silica sand was added to increase porosity of the contaminated soil. Highest Mn removal was achieved mainly by sulphuric and oxalic acid at 0.001M at all soil levels. EDTA was significantly efficient in the removal of Ni and Zn. The recovery of heavy metals, particularly Mn, decreased as the depth of sampling in-creased. Heterogeneous bacteria and filamentous organism plate counts were conducted to evaluate the growth of the bacteria and filamentous organisms in the soil. Results showed that more organism growth took place in the bioremediated soil with a fertilizer added to it. The leaching of metals from the soil that was bioremediated in the pilot study was generally higher than the extraction of the metals from the soil that was leached with no bioremediation carried out. The results from this study suggest that the leaching of heavy metals from the contaminated soil is to a large extent dependant on the pH of the leaching solution. By increasing the soil?s porosity and bioremediating the soil, higher extractions of metals were achieved.

Jan 1, 2014

By Mohan Ram

Structural impurities in the crystal lattice of rock phosphate of Indian origin is a great challenge for beneficiation and practically possesses remote scope of upgradation to the desired level for industrial utilization. There is a wide occurrence of rock phosphate in different parts of India with different characteristics viz. siliceous, carbonaceous and ferruginous. The structural cationic replacement in the composition of apatite is due to the exchangeable cations present in the external impurities associated with the rock phosphate ore. The Indian rock phosphate ore from Purulia district, West Bengal is characterized as unusual structural composition due to the exchangeable cation in its composition. The elemental distribution of ore exhibits the disproportionate ratio of P2O5 and CaO which is 5.88: 3.31 in reference to the theoretical composition of P2O5: CaO in apatite which is 4.23: 5.55. The substitution by trivalent Al+++ cations within the structure of apatite in place of divalent Ca++ is found upto 18% and substitution of exchangeable cation in place of PO4 and F ion by CO3/SO4 is found upto 0.1% and OH ions upto 0.2% respectively in a lattice of apatite thereby diluting the grade of rock phosphate and restricting its industrial use even after beneficiation. This paper reveals the unusual compositional features of rock phosphate under study and is a guideline to the mineral industries using such rock phosphate. Keywords: external impurities, exchangeable cation substitution, structural compositional features, electron probe micro analyzer

Sep 1, 2012