Search Documents

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto

"The theoretical technique of computational modeling and the experimental determination of the enthalpy of adsorption of a ligand molecule onto a mineral surface deliver the same output parameters and, therefore, complement each other in investigating the affinity of different ligand types for mineral surfaces.This study ran parallel experimental tests and computational calculations to determine the enthalpy of adsorption of a series of increasing chain length xanthates onto a pyrite surface. The outcomes showed that, while the absolute energy values were different, the trends were similar. Both computational and experimental approaches showed that the extent of the interaction of the xanthate molecule increases with increasing carbon chain length. The computational values were larger than the experimental values, which could be explained, in part, by the addition of water to the computational system, which resulted in a decrease in the heat of adsorption on the (100) surface, compared to the adsorption of the collector in a vacuum. The computational method showed that, in the case of the pyrite (100) surface, the most exothermic reaction was obtained when the two xanthate sulfur atoms bridged two pyrite 5-coordinated iron atoms. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted for each of the C2, C3, C4 and C5 chain length xanthates.The experimentally determined exothermic increase in heat of adsorption for the addition of each CH2 group was found to be -8.17 kJ/mol. The contribution of the thiol head group was -34.9 kJ/mol. Previous studies on self-assembled monolayers have shown that these values are compatible with lateral interactions between CH2 groups and the exclusion of water. This study provides a rigorous experimental and computational approach which is intended to afford confidence in modelled data for the screening of new ligands for flotation processes.INTRODUCTIONComputational modelling is a fast and cost-effective method of screening collector molecules for the efficacy of their adsorption onto mineral surfaces. However, it is desirable to measure the computational outputs against experimental outputs to check for congruency. Computational modelling and experimental microcalorimetry both deliver the same output parameter: the energy of adsorption of the molecule onto the solid surface. These techniques are therefore ideally suited to complement one another in investigating the affinity of the interaction between collector molecules and mineral surfaces."

Jan 1, 2018

By Fengnian Shi

In the current energy-sensitive world, sustainable development in the mineral industry will require new, better and more efficient processes. Novel comminution methods, which offer the prospect of achieving the required outcomes of size reduction and mineral liberation at lower energy consumption, are continually being sought. In the past five years, extensive research using high voltage pulse electrical comminution technology has been carried out at the Julius Kruttschnitt Mineral Research Centre (JKMRC), in collaboration with selFrag AG. The major outcome of this research is the development of the concept of pre-weakening ore particles by electrical comminution procedures to reduce the energy consumption in the downstream grinding circuit. The research has also verified the preferential liberation of valuable minerals by electrical comminution. Given the advantages, several potential applications of electrical comminution in the mineral industry are proposed, including AG/SAG mill feed pre-weakening, pebble treatment, ball mill feed pre-weakening, early recovery of the liberated valuable minerals, crack/micro crack generation for improved leaching, and smelter slag treatment. For the mineral industry to utilize electrical comminution, two emerging issues identified from the research need to be address. They are the energy consumption by electrical comminution in the locked cycle treatment and the facilities scale up necessary to move this technology from the laboratory to the plant. Keywords: high voltage pulses, electrical comminution, energy efficiency, mineral liberation

Sep 1, 2012

By C. Perez

In mineral processing plants it is important to estimate rock composition, size and grindability to improve control of the grinding process. It is well known that variation in ore grindability and size distribution directly affects mills power consumption and throughput. This paper extends a general machine vision approach for on-line estimation of rock mixture composition using color information. Our proposed rock lithological recognition method requires the following steps: division of each image into sub-images, color feature extraction using the Binary Quaternion-Moment-Preserving thresholding technique (BQMP) and support vector machines (SVM) for classification. The BQMP thresholding technique splits the image in two and chooses representatives of each half using the histogram as features. The statistical parameters of the color data can be expressed using the quaternion moments into the representatives. This method can be recursively applied to the sub-images, obtaining 5x2n features in n iterations. Once the feature vector has been computed, each vector is assigned to one of three classes using a classifier. The method was tested on a database containing 20480 sub-images (64x43 pixels) of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets: 15360 sub-images used for training and cross validation and 5120 sub-images used for test. The classification accuracy was compared with a method previously published based on a mixture of principal components analysis (PCA) for color, and wavelet texture analysis (WTA) for texture feature extraction. WTA-PCA approach reached a 76% accuracy in test while our BQMP method reached 90% of classification accuracy using only color features. Experimental results show that our proposed method yields excellent results compared to previously published results. Keywords: rock classification, lithological classification, grindability estimation

Sep 1, 2012

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By N. Acarkan

Beneficiation of the pyrite concentrate of the Kastomonu-Küre (Northern Turkey) copper ore seems to be attractive due to its high Cu, Co, and Zn contents. Pyrite concentrate were used in the experimental studies. Cu, Co, and Zn were recovered from the concentrate by the sulphatizing roasting, leaching and the precipitation using H2S. Sulphatizing roasting experiments were carried out in a rotary furnace and the optimal roasting conditions were found to be at 650°C roasting temperature and 3.0 h roasting period and addition of Na2SO4 of 3 % for the concentrate containing 0.58% Cu, 0.22% Co, and 0.04% Zn. Then, the roasted product was repeatedly leached with 10 g/L H2SO4 solution. Optimal conditions were found to be 60 oC leaching temperature, 2 h leaching period, and 30% pulp density. Leaching efficiencies for Cu and Co were over 99 %. The valuable metals in the pregnant solution were selectively precipitated by H2S as sulfides. Selective precipitation of Cu, Zn, Co was achieved by adjusting the pH and the temperature of the leach solution. Final metal recoveries of 99.20% Cu, 99.40% Co, and 95.60% Zn were attained. The precipitated sulphides are marketable products. Roasting gases with their 15% SO2 content are suitable for the production of H2SO4 and the leach residues can be integrated with the iron ore processing plant as they contain 57.50 % Fe, 17.70% gangue (SiO2, CaO, etc.), 0.04% S, and 0.06% non-ferrous metals.

Jan 1, 2014

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By Graeme Lamson, Rene Dobbe, Merle Kalstrom, Janice Baron, Robert Thorpe, Chris Martin, Snezana Bajic, Amanda Palko

"This paper presents early results from a case study at the Mount Polley porphyry copper mine in British Columbia, Canada. Daily mineralogical data was acquired and reconciled with daily plant assay and recovery balances to interrogate the mineralogical controls on plant performance. After commissioning, the Minesite machine operated smoothly and reliably, creating daily data to generate mineralogical balances around the circuit for a period of several weeks. The key data, on final products were produced within 13 hours of the end of the respective operating period. The resulting information allowed for a greater understanding of the opportunities and limitations of the Mount Polley metallurgy. In this paper, how this information can be used to help long term strategic planning for the operation, as well as mine planning and production forecasting and the fine tuning of day to day mill operations is described. Early data available at the time of preparing this paper indicated that roughly 40% of the sulphide losses, or 32% of total copper losses existed as low grade inclusions in +75 micron tails. This represented the dominant form of long term copper losses, demonstrated repeatedly in the routine analytical data. However, on a day-to-day basis, the amount of copper present as chrysocolla is the major driver behind variations in total copper recovery. The degree to which this influences mill recovery is valuable to the geologist or mine planner. As they are armed with mineral speciation information for future ores, this will allow for improved mine planning, prediction of copper recoveries and production forecasting. The data was also started to find value in the mill by showing what caused sulphide losses. In the roughers, for example, the data showed poor recovery was the result of poor flotation performance and not any changes the speciation of copper sulphides or their liberation characteristics."

Jan 1, 2014

By Yagmur Sirinyurt, Ayhan Ali Sirkeci, Gülay Bulut, Mustafa Özer, Tuncer Acar

"The basic requirement of glass industry for the silica sand is at least 99% SiO2 content. On the other hand, coloring impurities such as Fe and Ti, must be removed. Flotation is the most widely used method for the purification of silica sands from impurities. In this study experimental studies were carried out to reduce Fe content of Mersin (Turkey) district silica sands by flotation. Silica sand sample with a d80 particle size of 1.85 mm was reduced below 0.5 mm in size. Then the size fraction -0.5 +0.106 mm was subjected to flotation tests. In flotation tests, sulfonate-type R801-R825, fatty acid based DER NA 7 (Produced by a Turkish company) and HA110-HA150 a blend of various chemicals produced by Mersin Cam-Is Mining Company (producer of glass raw materials) were used as collectors. Flotation tests showed that sulfonate type R801-R825 collectors provided much better results in acidic medium (pH: 3). The optimum pH value for DER NA, HA150 and HA110 collectors was found to be 7. It was observed that the addition of collector at once caused an increase in the amount of floated product that resulted in a loss of silica to the tailings. In the case of multistage addition of the collector much better selectivity was achieved. As a result of flotation tests conducted under best conditions, a concentrate assaying 0.046% Fe was obtained with a weight percentage of 93.4 when DER NA 7 was used as a collector. In the case of R801-R825 a concentrate was produced with 0.058% Fe content with a yield of 98.4%. On the use of HA150-HA110 the concentrate was produced with 96% weight recovery and 0.052% Fe content."

Jan 1, 2014

By B. P. Baruah

A good deposit of high sulphur coals of tertiary origin is existent in North eastern region of India. These coals are known to have indifferent characteristics in comparison to other Indian coals. The general Physico-chemical characteristics are low ash and high volatile matter, calorific value and sulphur content. Sulphur in these coals (70-95% of organic) is mostly affixed to the structure of the coal. Owing to the stringent environmental regulations, the utilization of these coals has severe limitations due to high sulphur content. In the present investigation, sulphur incorporation in to these coals has been discussed along with possible organic sulphur functionalities. The various desulphurization techniques carried out for removing sulphur from these coals have been discussed. Two step oxidative desulphurization processes has been found to be most efficient for organic sulphur removal along with mineral matter and potential toxic elements. Keywords: oxidative desulfurization, potential toxic elements, sulfur incorporation

Sep 1, 2012

By Gaurav Soni, Roe-Hoan Yoon

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model predictions have been compared with the results of a series of laboratory flotation tests conducted using mono-sized glass beads of different particle sizes and contact angles under different operating conditions. Some of the experiments were conducted using a 1:9 mixtures if hydrophobic silica and hydrophilic magnetite, so that the product graded could be readily determined by simple magnetic separation. The model predictions are in good agreement with the experimental results both in recovery and grade. A computer simulator developed on the basis of the model is capable of designing a preliminary flotation circuit on the basis of feed characteristics, e.g., size-by-liberation data, and the hydrodynamic information on the flotation cells to be incorporated in the circuit.

Jan 1, 2014

By Y. M. Zhu, G. C. Gong

"The influences of citric acid (CA) on the flotation behavior of cassiterite using styrene phosphonic acid (SPA) as the collector were studied via single mineral flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations in this paper. The results of single mineral flotation tests revealed under the conditions that pH=4 and the dosage of SPA 100 mg/L, the recovery of cassiterite reached 76.78%. The addition of 20 mg/L AC decreased the recovery by 12.42% at pH=4. Contact angle measurements demonstrated the adsorption of CA prior to SPA made the cassiterite more hydrophilic. The results of zeta potential determinations and solution chemistry calculations indicated the chemisorption of C6H7O7- and C6H6O72- filled parts of the Sn site on cassiterite surface and prevented the SPA from getting adsorbed. The hydrophilic effect of AC was stronger than the hydrophobic effect of SPA and the flotation of cassiterite was crippled. INTRODUCTION Tin is an important metal which is widely used in medical instruments, marine engineering materials, electronic and electrical devices, welding, weapon manufacturing and organotin compounds industries (Angadi et al., 2015). Cassiterite is the only mineral from which the tin can be extracted, thus it is of great importance to efficiently exploit the cassiterite mineral. Flotation is an indispensable method for the recovery of cassiterite (Li et al., 2015). However, cassiterite is usually in association with many other gangue minerals which are of similar floatability, such as quartz, calcite, fluorite, iron oxide, wolframite, scheelite and tourmaline (Sreevinas, 1997). So some modifiers are necessary in the cassiterite flotation process. The amounts of the modifiers used in the flotation must be judicious and the overmuch modifiers may cripple the recovery of cassiterite (Parsonage et al., 1987). Nevertheless, the research about the effects of the modifiers on the flotation behavior of cassiterite has been rarely reported. In this paper, the influences of citric acid (CA) on the flotation of cassiterite using styrene phosphonic acid (SPA) as the collector were investigated by flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations."

Jan 1, 2018

By Fuqiang Zheng, Shuai Wang, Feng Chen, Yufeng Guo, Guanzhou Qiu, Tao Jiang

"The direct reduced iron powder and Ti-V-rich material was prepared from vanadium titanomagnetite concentrate by solid-state reduction-magnetic separation. The result indicated that under the studied conditions, adding KS can effectively improve the metallization rate of pellets. 2% KS was well mixed with vanadium titanomagnetite concentrate to make the pellets. The green pellet was preheated at 900 ? for 6 min. The preheated pellet was reduced at 1050 ? for 100 min, then crushed and ground to more than 80% was below 0.045 mm. The direct reduced iron powder and Ti-V-rich material were separated from the slurry by wet magnetic separation at 800Gs. The TFe content of magnetic material was 90.63%, and the Fe recovery rate reached 96.53%. The TiO2 and V2O5 contents of Ti-V-rich material were 28.40 % and 1.64 %, respectively. The TiO2 and V2O5 recovery rates were 69.05% and 96.82%, respectively. 1. Introduction The ilmenite and rutile are the main titanium resources which can be used in the present technical level and economic conditions[1,2]. However, with the rapid development of China’s economy, the market demand of titanium products is increasing sharply. The current supply of ilmenite and rutile cannot meet the needs of chemical industry[3]. China is rich in vanadium titanomagnetite concentrate which contains abundant titanium and vanadium resources. The TiO2 and V2O5 content of vanadium titanomagnetite concentrate are usually about 7% and 0.3%, respectively[4]. Because the TiO2 and V2O5 grades are low, it generally requires pre-concentrated to Ti-V-rich material before extracting the titanium and vanadium. Therefore, it is vital to find effective processes for pre-concentrating the titanium and vanadium in vanadium titanomagnetite concentrate. There are many methods[5-13] developed or under development to pre-concentrate Ti-V-rich material from vanadium titanomagnetite concentrate, including the blast furnace process, pre-reduction electric furnace process, to utilized vanadium titanomagnetite concentrate are direct reduction-electric furnace smelting, sodium salt roasting-direct reduction-electric furnace smelting and direct reduction-magnetic separation and so on. The blast furnace process and other methods cannot effectively utilize the titanium and vanadium resource due to the technical or environmental problems[9]. In this study, the vanadium titanomagnetite concentrate was obtained from Panxi region of China, the reserves of which account for 11.6% of vanadium and 35.17% of titanium all over the world[3]. The preparation of direct reduced iron powder and Ti-V-rich material based on reduction-magnetic separation is proposed. The process utilizes a new catalyst for titanium ore reduction in rotary kiln followed by magnetic separation. Using this novel technology, the titanium-vanadium and iron are successfully separated. Compared to the traditional reduction of Ti-bearing ore, the reduction temperature reduced to 1050 ?, leading to higher efficiency, lower energy consumption and investment, and broader applications."

Jan 1, 2018

By Josefin Lannefors, Anders Klingberg, Natalija Gorochovceva

"Development of new anionic collectors becomes more and more important. This can be explained, on the one hand, by the fact that over the years phosphate ores have become more fine grained and complex (example weathered). On the other hand, a development with a focus on sustainability (sustainable development) of new anionic surfactants is required by authorities and society. Within the sustainable development several characteristics of a collector have to be taken into an account: efficiency, selectivity, froth characteristics, environmental profile, raw materials used for the synthesis, manufacturing complexity, stability upon storage, etc.Several anionic surfactants based on ester and amide chemistry were synthesized, characterized and used as flotation agents for calcium phosphate containing ore. The surfactants were used in a formulation together with other anionics, since in a pure form, during the flotation, they did not provide right froth characteristics.A new anionic collector/formulation was developed, that fulfills all above listed requirements."

Jan 1, 2014

By Qingming Feng, Dongbo An, Jinhong Zhang

The application of the geopolymerization of mine tailings as construction materials is hindered by the fact that conventional geopolymerization of mine tailings usually involves a large consumption of alkali, i.e., sodium hydroxide (NaOH), and a long curing time, because of the relatively low reactivity and the high Si/Al ratio of mine tailings when compared to other active resources such as fly ash and clay minerals. The present study is focused on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. We firstly investigate the temperature effect on the alkali activation of mine tailings during geopolymerization. Secondly, the impact of additives, i.e., calcium hydroxide and aluminium oxide, on the compressive strength of samples is studied. Thirdly, different forming pressures have been applied to remove excessive alkali and its impact on samples' strength has been investigated. The results show that a 40 MPa unconfined compressive strength (UCS) can be achieved with the geopolymerization samples after mine tailings are activated by sodium hydroxide at 170°C for 1 hour with the addition of calcium hydroxide and alkali dissolved aluminium oxide, further compressed with a 10 MPa forming pressure and finally cured at 90°C for 3 days. The findings of the present work provide a novel method for the geopolymerization of mine tailings as construction materials.

Jan 1, 2014

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By G. Bulut, Ü. Yenial

"Heavy metals contamination in aqueous systems can be found in a variety of industries, in particularly mining, metal processing, finishing and plating. Water containing more than 0.5 ppm heavy metal considered as a toxic due to harmful effects on health. The major techniques employed for heavy metal removal from industrial wastewaters include precipitation, reduction, ion-exchange, and adsorption. Adsorption is a heavy metal removal method for aqueous systems. As a common adsorbent, activated carbon has been used in treatment but it is ineffective on some elements. Thus, there has been a research for developing highly effective and selective adsorbents. In this study the adsorption of lead and arsenic ions on to coal waste and red mud waste was studied. The experimental parameters were determined as pH, equilibrium time and the initial concentrations, activation by heat treatment and the blend of adsorbents. According to their adsorption capabilities, red mud was found to adsorb lead and arsenic ion with high efficiency but coal waste did not adsorb arsenic ion. However the binary adsorptions of these ions were enhanced the adsorption efficiencies. In addition the blend of coal waste and red mud affected the adsorption efficiency. INTRODUCTION As a result of rapidly developing industry and excessive use of water resources, the need of clean water and wastewater management appear as a problem. Wastewater recycling activities and researches come to the fore for an effective use of wastewater. Recycling of wastewater, which contains heavy metals harmful to the environment and human, is a difficult process. Heavy metals are generally divided into three categories: toxic metals, precious metals, radionuclides. Wastewaters from various industries, containing heavy metals, are the main polluters of water and soil. Although their toxic structures, heavy metals are used extensively in industry as they have technological significance. Usually mining industry, metal industry and industrial organizations produce heavy metal containing wastewaters (Volesky 1990, Ting and Lawson 1991, Bishop 2002)."

Jan 1, 2018

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By Richard A. Williams

The mineral processing community have been amongst the pioneer developers and early adopters of key platform technologies in analytical methods, chemistry, physical separation and advanced modelling. Fundamental research will continue to have a significant impact driven by the continued development of sustainable practices. Major drivers and challenges for change in our industry in the next two decades include: reduction in energy uses in processing; discovery of new energy materials; adoption of green chemistry routes; safeguarding of water resources; and demonstration of adherence to best practice at all times. With increasingly global mining enterprises, the provision of internationally accepted benchmarks for performance will continue to drive the creative process. This lecture highlights major opportunities around a new paradigm of Multi-scale Measurement coupled with Multi-scale Modelling, based on advanced sensors, communications and computing. Connecting real-time measurement sensors with dynamic simulation models opens up new horizons for visualising the process behaviour from an experimental and theoretical basis. Examples are given of the potential of this methodology and its implications for better design.

Jan 1, 2003

By A. An. Mushketov, A. Al. Mushketov, N. A. Sopina

"INTRIDUCTION At present, more and more metallized raw materials with a metallization degree of not less than 80% are used in the smelting of steel. The main quantity of this raw material is produced in furnaces of mine type. Advantages of this type of raw materials for metallurgical processing are low levels of harmful and slag-forming impurities and a high content of metallic iron. At the same time, the cost of smelting raw materials and obtaining high-quality steels are reduced. In addition to the undoubted merits of metallized raw materials, there are high requirements for the quality of iron concentrates, which are the starting material for metallization: the mass fraction of acidic oxides should not exceed 3%; The mass fraction of iron should not be less than 69%, mass fractions of harmful impurities (phosphorus, arsenic, sulfur, copper, etc.) should not exceed 0.02%. These requirements are dictated by the fact that the recovery of burned pellets is carried out by gas in a solid phase. In this case, the empty rock and harmful impurities from the metal are not separated and sent to the steelmaking unit, increasing the heat consumption for heating and worsening the quality of the steel. The combined production of high-quality concentrate and metallized raw materials requires a large capital outlay from the enterprise, which in the future can be compensated for by increased profit from the sale of more expensive marketable products. At present, in the territory of Russia and the CIS countries Lebedinsky mining-and-processing integrated works is the only enterprise that carries out the entire chain of operations for the production of metallized raw materials, starting with the production of high-quality magnetite concentrate with a mass fraction of iron of 69.5% and ending with the production of a metallized product in the form of hot briquetted gland. JSC «SSGPO» is the largest iron-processing enterprise in Kazakhstan, which processes about 40 million tons of ore per year and receives 16 million tons of concentrate per year with a mass fraction of iron 66.0-66.5%. The technological scheme existing at the concentrator of JSC ""SSGPO"" includes the crushing of the feed ore to the size of 20-0 mm; dry magnetic separation operation; three reduction stages to a fineness of 90-95% kl-0.071 mm; operation of desliming, wet magnetic separation and filtration of the concentrate. Dry magnetic separation of the feed ore makes it possible to remove from the process of 19.6% of the tailings with a mass fraction of the total iron 12.5%, of magnetite 2.2%. The first reduction stage is carried out in rod mills with the volume of 40 m3 to a size of -1.6 + 0.0 mm. The first stage of wet magnetic separation is carried out in counterflow magnetic separators PBM-P-150/200L. The magnetic product of the first stage of WMS is classified in hydrocyclones; sands enter the second reduction stage into central discharge ball mill 3600 × 5000. Runoff of mills enter on the second enrichment stage in counterflow magnetic separators PBM-P-150/200L. The magnetic product enters the classification of the second stage, forming a closed cycle. Mass fraction of the class -0.071 + 0 mm in classifications runoff of the second stage is 70-75%. The second stage classifications runoff is transported toWMS-III operation in semi-counter separators PBM-PP-120/300. The magnetic product of the third stage enters the classification of the third stage. Granular residue are transported to the reduction of the third stage into central discharge ball mill 3600 × 5000. The mill runoff enters the third stage of classification, forming a closed cycle. Classifications runoff of the third stage enters on deslimation. Deslimed product is sent for fine screening to the crasher «Derrick» 2SG48-60W-5STK with a cell size of 0.1 mm. Top size of crasher is sent to regrinding. Undersize with a mass fraction of the class -0.071 + 0 mm 90-95% is fed to the wet magnetic separation of WMS-"

Jan 1, 2018

By F. Göktepe

Flotation gases and conditioning of the pulp with them are one of the important parameters of flotation and should be taken into account especially in the flotation of sulphide ores. In this study, flotation of pure chalcopyrite and pyrite samples were investigated with air, oxygen and nitrogen as flotation gas and the effect of conditioning with these three gases also were performed. Flotation gas was introduced for 5min, 10min, 15min and 20 min. For chalcopyrite flotation there was no drastic change in recovery when air, oxygen and nitrogen were used as flotation gas but conditioning the pulp with oxygen for 10 minutes increased the recovery about 8% where pulp potential has been approximately 25 mV with chalcopyrite and 150 mV with platinum electrodes. Conditioning with all three gases decreased the pyrite recovery by about 20% with 20 minutes conditioning. Pulp potential decreased in the presence of nitrogen while conditioning with air and oxygen increased the pulp potential for both electrodes. Generally potential increased for both minerals with oxygenation and aeration time but it was stable or slightly decreased with nitrogenation. Comparison of the gases showed that the different flotation gases do not effect flotation recovery but conditioning the pulp with these gases at pre-flotation effects chalcopyrite and pyrite flotation recovery, most dramatically pyrite.

Jan 1, 2014