Search Documents

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By Sanjay Agarwal

Polymetallic sea nodule is a good source of manganese having 22.3% Mn, 5.4% Fe, 6.14% Si, 1.1% Cu, 1.15% Ni, 0.076% Co & others. These nodules are available in plenty on the sea beds, generated over thousands of years. Nodules mainly consist of manganese dioxide and iron oxide phases and other metals are entrapped in the complex cage of these Mn-Fe oxides phases.World-wide research is going on sea nodules as an alternative future source of many metals, which has led to intensified efforts to develop practical and economical processes for recovery of these metals. Very little attempt has been made world over on manganese extraction from sea nodules. We at CSIR-NML, India have developed a direct reduction smelting process of nodules to recover manganese as Fe-Si-Mn alloy. This alloy is extensively used in the steel industry as deoxidizer and as an alloying element to make different grades of steel. Lab scale experiments were conducted to study the manganese distribution between Fe-Si-Mn alloy and FeO-SiO2-MnO-CaO-Al2O3-MgO slag at different temperatures by varying the basicity of the slag. The direct reduction smelting of nodules is carried out on 1 kg scale in 50 kVA electric arc furnaces to have Cu, Ni and Co alloy and Mn rich slag. This manganese rich slag is further treated in 50 kVA arc furnace to produce Fe-Si-Mn alloy. The composition of Fe-Si-Mn alloy obtained is in the range of Mn: 60-65%, Si: 14-17%, C: 1- 2%, S: 0.03% and the balance iron which is acceptable grade for industrial use. The equilibrium amount of MnO in the final slag is controlled by the temperature of the final melt and the silica, lime, alumina content of the final slag. Increasing the basicity of the slag plays a major role in minimizing the loss of MnO to slag, increasing the amount of SiO2 of the slag, increases the manganese loss in the slag. Increasing the CaO/ Al2O3 ratio of the slag decreases the manganese loss in the slag. Increasing the MgO/CaO ratio of the slag increases the manganese loss in the slag. Thus by adjusting

Sep 1, 2012

By E. N. Levchenko, K. V. Bulatov, G. I. Gazaleeva

"The article highlights the new procedure of choosing special methods of disintegration for very complicated rare ores. Especially, there is a complex approach to criteria of comparing different types of crashing machines. Criteria are as follows: degree of crashing, degree of grinding, degree of slime creation and the new creations criteria for selection. The procedure is tested on tantalium and zelestinium ore. A new methods was shown the preference impact crashing machine MD-7 for zelestinium ore. In product of crashing 0,050 mm size are 9.4 %, 0,005 mm size – 2.5 %.This is gut result, and show the best indexes of slime creation. The check of the proposed new methods was done when comparing the crushing of tantalium ores of the Otboynoe deposit in cone inertial and centrifugal impact crushers and roller press. A research was conducted different crashing machines under laboratory and semi-industrial conditions. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion and degree of crashing showed that the centrifugal impact crusher (CC) and roller press (RP) has the lower indexes than the cone inertial crusher (CIC). Degrees of crashing for different crashing machines are:centrifugal impact crusher – 10.1;roller press – 10.8;cone inertial crusher – 14.2. The crusher CC the selection criterion is 0,632 units, RP – 0.730, where as for the crusher CIC – 0.848 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 0°, peripheral speed of a cone rotation – 1420 r.p.m, specific energy consumption- 4.99 kW*t/t. Crusher CIC-300? is the best for tantalium ores of the Otboynoe deposit. The new methodic are verification.INTRODUCTION Rare metal concentration circuits are complex, energy-intensive, and costly. The reasons for this include the multimetal nature of the rare metal ores, their volatile material composition and low grade. That is why careful selection of ore preparation circuits is of great importance for minimizing the energy inputs and maximizing the liberation of the valuable minerals. Recent research (Khopunov, 2011, Gazaleeva, 2015) has demonstrated that the most efficient comminution processes available to the mineral processing industry are selective disintegration, crushing and grinding, allowing to liberate the mineral particles along the cleavage in the comminution process. These methods are indispensable for the processing of finely disseminated refractory ores prone to slime formation. Many rare metal ores found in Russia are of this type."

Jan 1, 2018

By E. Szelag

The adsorption and stabilization of mineral dispersed systems by using Pluronic copolymers with different molecular weights and EO content has been studied. The role of sequential adsorption of EO-PO copolymers and cationic surfactant (CTAB) on the carbonate particle properties and in determining the stability of their suspension was studied with particular attention to the conformation of the polymer at the solid-liquid interface. The purpose of this work was to investigate the flocculation phenomena, influence of polymer molecular size on stability of suspensions of magnesite and dolomite and the effect of addition mode of polymer and surfactant. The suspension stability measurements and the determination of sedimentation speed were carried out using an optical analyser (Turbiscan). In most of investigated cases, the biggest floccs and the fastest sedimentation were found for low concentrations of copolymers.

Jan 1, 2014

By Felipe Henríquez, Daniel Silva

"Traditionally, the implementation of an automated advanced process controller in any mineral processing complex is a challenge, mainly due to the quality of resources and technologies required, the uniqueness of each control solution and the uncertainty of the engineering hours needed to complete the task. Thus, the use of advanced and proven control technology becomes a key factor when deploying the control strategy. However, success would still not be possible without the presence of common sense, process knowledge and fundamental process data. Minera Los Pelambres, taking advantage of such factors and its accumulated process experience, implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control for secondary grinding and regrinding stages at its copper concentrator plant. In both cases, the control objectives are: being capable of processing a variable feed from the upstream process while at the same time avoiding to become a process bottle neck and yet, maintaining an adequate product quality (in terms of size distribution) to the process downstream. Additionally, for the case of the vertical regrinding mill (vertimill), the control system should also be capable of keeping an adequate circulation load and making an efficient use of the available grinding power. In either case, extending hidrocyclones availability while maintaining their performance is a must, since both factors are required for process and maintenance purposes. Thus, the process control problem becomes one with a multi-variable type of process with multiple control objectives to satisfy simultaneously. In trying to solve it, many mineral processing operations have implemented basic or conventional control or even better yet, expert systems. Minera Los Pelambres believes that better and faster results can be achieved using a combination of MPC and advanced control. Such strategy was successfully implemented, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Their control philosophy, implementation process, main results and their key performance indicators are discussed here."

Jan 1, 2014

By Robin B. Batterham

"Since the 1970?s we have seen a marked corporate response in terms of the environment. In part this has come from regulation but it has largely come from stakeholders and the community. Rising expectations have in general been met. We now see a similar trend towards sustainability. At the same time, the importance of mining to the share market has decreased drastically and with that decrease has come the requirement for the mining sector to show returns similar in manner to other sectors. While rationalisation can achieve some progress towards these goals, the long-term requirement is for innovation, as it always has been. This paper looks to the logical goal of innovation within a sustainable mining framework and targets the removal of the desired metal values with minimal environmental footprint. It is suggested that broad ranging alliances will be necessary, particularly amongst the R&D suppliers, to achieve this goal. Industry will need to take an active role given the recent global restructuring.THE MARCH TO SUSTAINABILITYSince the 1970?s there has been an increasing corporate response on environmental matters. We have moved from matters environmental being issues relevant only to minority groups through a series of attitudinal changes by management. Whilst there have always been examples of excellent environmental performance, for many in the 70?s spending money on improving the environment beyond some minimal level was seen as a distraction from production or treated in a similar way to donations to the community. There is little of that attitude these days, as most mining companies have long since regarded the environment as a core business direction. Indeed, for some years one could note an escalation in matters of environmental reporting to the extent that the environmental performance of companies is now very public. In some cases, NGOs have even been invited to help certify and audit the reporting standards. Similarly with health & safety.There is now a rising expectation on the part of the community that social matters will also be given the same level of support as health, safety and the environment. This time around it would appear that the mining industry is at the leading edge of sustainability. The Global Mining Initiative (Global Mining, 2002) and the contributions to the Rio World Summit on Sustainable Development (Rio +10, 2002) suggest that sustainability is being taken very seriously by the mining industry. For sustainability it is convenient to use the Brundtland (1987) definition. This definition has widespread acceptance with governments, industry, environmental groups, financial institutions and individuals as a direction against which our activities and plans can be measured."

Jan 1, 2003

By Per Svedensten

One of the most significant behaviour of a crushing plant is the constant variation in the process. The variation is caused by two major effects. The first and constantly changing is the rock material properties. During operation rock material with different strength and particle size distribution is fed to the plant which makes the performance of the equipment to vary. The second and more slowly changing variation is caused by wear on the processing equipment. These effects must be predicted in order to be able to optimise a crushing plant. This paper demonstrates how Monte Carlo simulation can be utilised to study and operate crush-ing plants. By introducing Monte Carlo simulation the varying process can be study and also optimised. To maintain the optimised process performance supervision is needed. This paper demonstrates how results from the Monte Carlo simulation can be utilised for process supervision. Charts for process measurements can for example be derived. These can then be used to guide decision making and understand how the variation and performance of the plant changes over time.

Jan 1, 2014

By L. Weitkämper

The big challenge at present and in the future is the economization of resources. This is applied for the whole industry but particularly in fields of mineral processing. The most important resources are energy and water. The shortage and price advance of energy is worldwide noticeable whereas the shortage of water is regionally limited at present. However due to the increasing world population, associated with a rising standard of living, water will become more and more important. Studies of the Unesco from 2001 indicate that the total water consumption raised seven times since the last 100 years at a growth of population of just three times. (UNESCO-Currier, 10/2001). This trend is going to be increased. While today more than 90 % of the humanity has access to clean water, in 2050 just about 50 % will be in the same situation. These figures indicate the importance of a gentle handling with the resource water. Further more the disposal of fine products, containing most of the water, is an environmental concern and in the future the mining and processing of raw materials will become important and necessary in desert, arid or permafrost areas. In these areas just efficient dry cleaning technologies will allow an economical beneficiation or better enable the processing at all. Most of the separation technologies with high throughput rates in mineral processing are based on wet processes. This applies especially for the separation of fines. Though there are some dry technologies available for the separation of coarse materials, like pneumatic gravity separation [air jigs and air tables], magnetic separation and not least sensor based sorters. Dry separation of fines is bounded mostly on cost intensive and low throughput technologies. The pneumatic separation undergoes at present a renaissance, mainly due to the development of the all air jig by the German supplier Allmineral. This newly developed sorting device yields good results in the separation of coarse to medium size material. All these facts and figures show the potential and motivation for developing an efficient dry separation device for fines. The following article delineates the development, performance and chance of a new dry separation technology for fines.

Jan 1, 2014

By R. T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and-error techniques. This paper introduces a two-dimensional finite element model of briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, the velocity field, the stress distribution, roll force and torque. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquette after its exit from the roll. This enables to perform realistic computer experiments which are helpful for establishing the forming cavity geometry and process conditions necessary to produce briquettes with the desired properties. Three forming cavity profiles are analyzed. Results from model are verified on experimental roller press and best cavity profile is recommended for briquetting of sub bituminous coal fines.

Jan 1, 2014

"A sulfide ore containing 2.19 g/t Au and 13.13 g/t Ag was studied for the deportment and extractive metallurgy of pay metals. The ore is composed mainly of non-sulfide minerals with approximately 10% pyrite and minor amounts of marcasite, chalcopyrite, galena, sphalerite, and arsenopyrite. The deportment study using a comprehensive approach showed that gold and silver minerals in the ore are mainly native gold (Au), electrum (Ag, Au), petzite (Ag3AuTe2), hessite (Ag2Te) and volynskite (AgBiTe2) with minor amounts of acanthite (Ag2S) and argyrodite (Ag8GeS6). At current grinding fineness (P70@150µm), the majority of liberated native gold and electrum particles are larger than 20µm with 85% >40µm, some of them are even larger than 150µm, indicating that extended leach time may be required to dissolve these coarse gold grains to completion and gravity concentration needs to be considered. Petzite is relatively fine with all liberated particles being less than 80µm in size. Gold distribution and leach testwork results showed that liberated gold accounts for 50% of the head assay, exposed gold associated with sulfide and non-sulfide minerals accounts for 30% and 11% of the head assay, respectively. Gold locked in sulfide and non-sulfide accounts for 4.8% and 4.1%, respectively. Thus, it is recommended that cyanide leaching be considered for extracting gold in this ore. This paper presents the detailed results of the gold and silver deportment study and extractive metallurgy testwork, and discusses the impact on process selection and flowsheet development.INTRODUCTION Gold and silver have been found in various geological environments and ore types. In terms of the gold deportment and extractability, gold ores can be classified into two categories and 12 types. Their extractive metallurgy is largely driven by mineralogical factors such as particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide and sulfarsenide mineral structures (Zhou et al., 2004; Marsden & House, 2006; Zhou, 2013a, 2013b). Compared to gold, silver mineralogy is more complex and metal extraction is more challenging due to its presence in over 200 Ag-bearing minerals (a silver-rich ore body would typically contain 5 to 10 different silver minerals) (Gasparrini, 1984), presence of refractory silver minerals (such as pyrargyrite, prustite and stephanite) and submicroscopic silver in sulphide minerals (such as galena and copper minerals) (Chryssoulis et al., 1985; Di Prisco et al., 2002). The presence of these issues often causes problems in Ag-bearing ore processing. Therefore, knowing the deportment of gold and silver in the ores and metallurgical products is important for flowsheet development and process optimization."

Jan 1, 2018

By M. Taheri

Multiple Attribute Decision Making (MADM) method is applied to select tailings site of the Gol-e-Gohar Iron Ore Processing Plant in the Kerman province, south-eastern of Iran. To select tailings site, screening is applied on eight location proposed by Binnie and Granges. Consequently three sites identified for further studies. Evaluation factors include only the most important factors such as efficiency ratio, elevation and distance to processing facilities, occurrence of faults and fractures. Crisp values such as efficiency ratio, elevation and distance can be determined by measurements and calculations, but some factors such as occurrence of faults and fractures are presented as linguistic values that can be described with triangular fuzzy numbers. Based on evaluation values obtained an optimal tailings site can be selected using a modified Technique of ranking Preferences by Similarity to the Ideal Solution (TOPSIS) given crisp data and linguistic variables as the alternatives of attributes. Each attribute?s weight is assigned using the analytic hierarchy process. The final ranking order aids in the selection of tailings site. Finally, the stages of modified TOPSIS method were applied and site No.2 situated in 5400m to the mill was selected as the best alternative.

Jan 1, 2014

By N. P. Haran

A detailed study was undertaken to beneficiate sub-grade iron ore sample from Kenojhar District, Orissa, India containing 57% Fe (T), 7.7% SiO2, 4.8% Al2O3, 4 % L.O.I. 0.4% TiO2,1.3 % Mn and traces of S(T) to make it suitable for the user industry. The mineralogical study indicated that it predominantly consists of haematite with subordinate amounts of goethite and clay. Quartz, Cryptomelane / Psilomelane, Pyrolusite, Gibbsite, Feldspar and Muscovite mica were present in very minor to trace amounts. The Denver grind ability tests indicated, that the sample could be categorized as ?medium soft to medium.? The Bond ball mill work index was determined to be 14.19 kwh per short ton. The beneficiation process involved classification followed by tabling of the classified sand, ground to minus 48 mesh size. The table slimes were subjected to Wet High Intensity Magnetic Separator (WHIMS). The developed process yielded a composite concentrate from tabling and WHIMS operations assaying 65% Fe(T), 2% SiO2, 1.8% Al2O3, 2% Mn and 0.9% LOI with a recovery of 60.1% Fe (T), amounting to 52.5 wt.% yield. To meet the size specifications for pellet making, it was further ground. Dewatering studies were also carried out on the ground combined concentrate and rejects. The thickener area of ground combined concentrate using 0.02 kg/t of Sufloc A 1115 flocculant was 0.02 m2/tonne of dry solids per 24 h. And for the combined rejects using 0.12 kg/t of flocculant, it was 0.035 m2/tonne of dry solids per 24 h. The moisture content, in the pressure filtration cake, in the ground combined concentrate product was 10.0%, and productivity was 506.7 kg/m2h. Thus, by thickening and filtration of process products, 90% of water used in the process could be recovered. The study highlights the development of a simple and cost effective flowsheet with almost complete water recovery for a subgrade iron ore sample. Keywords: tabling, WHIMS, thickener, filtration

Sep 1, 2012

By E. T. Tuzcu

In this manuscript, a new approach for modeling the rate of grinding process is explained. A review about grinding rate definitions so far is given and the possible ultimate way for grinding modeling is given as modeling the rate based on energy spectra. The traditional/phenomenological approaches for modeling size distribution of grinding mills give their place to a new generation modeling technique. Developments in the computational methods and necessity to model product size distribution of large mills, larger than ball mill size, paved the way for this novel technique. The traditional grinding rate models are mostly based on the back calculated breakage parameters from the experimental data. However, direct modeling of breakage parameters and hence the prediction of size distribution of the grinding mills may become possible with this approach. The material breakage data and discrete element method (DEM) energy spectra are the main components of this approach. Albeit the focus in this study is on modeling of breakage rate under impact mode of breakage, the abrasion mode of breakage was also tested by carrying out abrasion tests. Impact mode of breakage was analyzed using ultra-fast load cell device (UFLC) and drop weight tester. Dry tumbling test was carried out for abrasion experiments. Obtained material breakage versus energy data are combined with the collision energy spectra to obtain the breakage rate function. In addition, the material breakage versus energy information from the tests is converted into breakage distribution function. The model was verified in a lab scale mill (90 cm diameter-15 cm length). 10 to 15 kg of limestone was ground using 50 mm steel ball at varying conditions, i.e., rpm, volume loading. It is shown that the proposed model predicts all (1, 2, 4 min.) grinding intervals for all experiments highly accurate.

Sep 1, 2012

By P. Fecko

The objective of the paper was application of bacterial leaching on two brown coal samples from locality Mine Druzba, seams Antonin and Josef (Sokolov brown coal basin, Czech republic). Based on the results of bacterial leaching and petrologic analyses of the given samples, it is possible to say that application of bacterial leaching gived good results. Applying bacterial leaching it is possible to remove from 34% to 47% of total sulphur and from 45% to 64% of pyritic sulphur from the coal.

Jan 1, 2014

By Kevin Galvin, Simon Iveson

Fine particles are the most valuable because they are the most liberated. However, they are also the most expensive and difficult to recover and concentrate. The Reflux Classifier is a novel invention that combines many of the virtues of existing fine particle separation technologies in a way that provides profound synergies. Multiple parallel narrow channels create a laminar-shear separation zone. The laminar flow provides a well-defined velocity gradient that exposes particles on the wall to a conveying velocity that is approximately proportional to their size, thus reducing the dependence of elutriation velocity on particle size. The high shear rate in these channels generates a hydrodynamic lift force that selectively lifts low-density particles off the channel wall and thus causes them to be preferentially conveyed out in the overflow. Particles that are not elutriated slide back down into the mixing reflux zone beneath the inclined channels which gives them multiple opportunities to re-enter the channels. The resultant suspension of both coarse and fine high-density particles in the fluidized bed zone at the base of the unit generates a strong autogenous dense medium that helps to direct large low-density particles back up to the overflow. The fluidization water also simultaneously de-slimes the high density underflow product. When placed in a centrifuge, the benefits of these features multiply with the improvements in capacity and selectivity that arise from high G-forces. When inverted, these features can be used to perform flotation well beyond the conventional flooding limit. Hence this invention platform has the potential to dramatically improve both gravity and flotation separation performance across the minerals processing industry.

Jan 1, 2014

By A. Chattopadhyay

Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex, ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.

Sep 1, 2012

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012

Copper nickel separation is performed by mineral processing techniques both pre and post smelting in Copper Cliff at Vale Canada?s Operations. The separation at Clarabelle Mill takes advantage of the ore mineralogy to affect a separation on the rougher concentrate where chalcopyrite and pentlandite exhibit high liberation and high recoveries thus their separation is simple although incomplete. The copper concentrate comprises only 50% of the copper in ore with the remaining copper being separated post smelting in the Matte Separation plant where the slow cooled Bessemer Matte is again treated by mineral processing operations using flotation to separate the chalcocite and heazlewoodite and magnetic separators to remove a metallic nickel alloy. This paper discusses the mineralogy, separation processes and work currently underway to improve the separation of copper from nickel in these plants.

Sep 1, 2012