Search Documents

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By D. Kosior

Influence of frothers (a-terpineol and n-octanol) concentration on kinetics of a three phase contact (TPC) formation by a bubble colliding with a hydrophobic surface (Teflon) of different roughness was studied using a high-speed camera (1040 frames per second). It was found that the Teflon surface roughness and the frother concentration strongly affected time of the TPC formation (tTPC) and time of drainage (tD) of the liquid film separating the colliding bubble from the solid surfaces. With increasing Teflon surface roughness, from ca 1 to 80 µm, the time of the TPC formation was shortened by over the order of magnitude, from ca 100 to a few milliseconds only. At low a-terpineol and n-octanol concentrations, thetTPC values were shorter than in distilled water due to lowering the bubble velocity in the frother presence and diminished bouncing of the colliding bubble. However, at high frothers concentrations the tTPC values were prolonged, despite that the bubble velocity was similar. The prolongation of the tTPC at high frother concentrations indicates that air (micro- and/or nano-bubbles) was present at the Teflon surfaces of different roughness. The mechanism of the tTPCprolongation at high frother dosage is described.

Sep 1, 2012

By Lala Zhao, Yuemin Zhao, Guangyuan Xie, Chusheng Liu, Chenlong Duan

"Screening is an important means of size classification used on granular or particulate materials. The vibrating modes of screen separator have a great effect on the screening process. Elliptical vibration mode is a complex motion mode which gets the common characteristics of both linear and circular vibration modes. However, the fundamental motion and screen penetration of the particles on the elliptically vibrating screen deck are still poorly understood. A numerical study of the motion of particulates flow along an elliptically vibrating screen deck is presented by means of a three dimensional Discrete Element Method (3D-DEM). The motion characteristic of the particle flow is analyzed at a particle scale. The effects of vibration amplitude, throwing index, vibration direction angle and screen deck inclination angle on the screening process are discussed. The results show that the particles average velocity increases linearly with the increase of vibration amplitude, throwing index and screen deck inclination angle, but decreases linearly with the increase of vibration direction angle. The screening efficiency is highest when the vibration amplitude, throwing index, vibration direction angle and screen deck inclination angle are 4.5 mm, 3.3, 40° and 6°, respectively. This work is helpful for developing a deep understanding of particle motion on the elliptically vibrating screen and for optimizing screen separator designs."

Jan 1, 2014

By Stephen J. Harker, John Knights, Randolph A. Pax, Glen A. Stewart

"Mineral samples were obtained from different stages of a mineral processing circuit used to extract the copper and gold rich mineralogical phases. The aim of this work is to characterise the quality of the samples at different stages of processing. The samples were taken of the head grade, tailings, cyclone overflow and the final concentrate.Characterisation of the samples was determined using Cu-Ka X-ray powder diffraction and Fe57 Mossbauer spectroscopy. These measurements will be presented and discussed in terms of the enrichment of the ore, showing the removal of magnetite and quartz through the processing, the final concentrate being rich in chalcopyrite and pyrite. This data also shows the utility of Mossbauer spectroscopy to provide mineralogical phase information directly.Mossbauer spectroscopy is a tool to determine the material phases of a sample. It is a nuclear based technique which measures the amount of attenuation of a narrow Doppler shifted source energy as it passes through a sample. The attenuation depends on the amount of resonantly absorbing material in the nuclear radiation path from the source to the detector. Synchronous detection of the doppler shifting velocity and the nuclear radiation count gives a Mossbauer spectrum. By convention, the energy axis of the Mossbauer spectrum is displayed in units of velocity.Figure 1 shows Mossbauer spectra obtained for a sequence of samples throughout a processing plant. These spectra show the removal of magnetite and the concentration of chalcopyrite and pyrite. Optical microscopy results indicated a significant component of bornite not witnessed with Mossbauer spectroscopy. Closer examination showed that optical microscopy assays over estimate the bornite component."

Jan 1, 2003

By Venkataramana Runkana, Shantanu Maheshwari

As the world reserves of high quality ores are getting depleted at a rate higher than ever, the liberation of valuable minerals from low grade ores is becoming more and more relevant and imperative. But, liberation of minerals from low grade ores requires grinding of ore to extremely fine sizes. High energy milling in a planetary ball mill is one such option where one can produce particles in the nano-meter range. Although planetary mill is employed extensively for ultrafine grinding, dynamics of grinding inside the mill is not fully understood because of the dependency of grinding kinetics on many interconnected phenomena like collisions between media, particles and wall, time dependent rheology, adsorption and desorption of dispersant, abrasion of media, agglomeration of particles, etc. It was well articulated in literature that media motion and number of media collisions have strong effect on grinding kinetics and final product size distribution. Simulations were carried out using the discrete element method (DEM) to compare the performance of a planetary mill with a ball mill, with and without lifters, in terms of impact energy and number of collisions and it was found that number of collisions is considerably high in the planetary mill. The high number of collisions might be the reason for production of ultrafine particles in the planetary mill. We have also fitted a population balance model (PBM) to experimental data from a laboratory scale planetary mill for prediction of particle size distribution. Unlike previous models, we have incorporated functional forms for the selection function and the breakage distribution function so that the number of parameters in the PBM is just five. The predicted product particle size distributions at different grinding times are in reasonably good agreement with experimental data.

Jan 1, 2014

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By Julian Dimitrov, Kremena Dedelyanova

"The paper presents research on hydrodynamic processes occurring at the elementary act of flotation. Discussed existing models to determine the effectiveness of conflict of bubbles with particles in vibration column flotation machine. The paper presents a disperser for a column flotation machine, in which the dispersion of the gas phase is carried out using vertical vibration with defined frequency and amplitude. The paper presents research of mechanism for the creation of air bubbles in vibratory column flotation machine. The factors influencing the increase in the duration of the bubble in the area of contact with the mineral particles are discussed. Research was carried out on the effect of frequency and amplitude of vibrations on speed of precipitation of mineral grains of different density. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in vibratory column flotation machine is determined. The vibrations of the hydrated layer allow for cost-effective implementation of the elementary act of flotation by providing larger relative velocities at the contact point between the bubble and the solid phase. It is proposed to complement the model more accurate representation the mechanism of attachment of the particles to the bubble."

Jan 1, 2014

By Nóra Schreithofer, Kari Heiskanen

"INTRODUCTIONThe knowledge of the adhesion forces between particles and bubbles is of key importance in the improvement of flotation models. The development of the Colloidal Interaction Force Measurement Apparatus (CIFMA) opened the possibility to quantify the adhesion forces between particles and bubbles. The aim of this study was to examine the effect of three main variables: the approach velocity, the loading force and the loading time on the adhesion force between an air bubble and a hydrophobized silica particle."

Jan 1, 2003

By Chao Li, Kym Runge, Saeed Farrokhpay, Dee Bradshaw

"It is well known that froth phase has a controlling influence on the overall flotation performance. Froth recovery is expected to be affected by froth transportation behaviour. The latter has been represented by different volume balance and energy balance based models. In froth transportation models based on a volume balance, the froth phase is divided into different zones. The total froth residence time is the sum of the time spent in each zone and is dependent on the cell geometry, bubble burst rate and the position that bubbles enter into the froth phase. Alternatively, the froth transportation model based on an energy balance treats the froth phase as a block. In this model, froth height above the concentrate lip is being predicted by minimising the energy of the system which is dependent on the froth geometry, froth stability and froth rheology. The froth height can be used to calculate the froth efficiency of delivering mineralized bubbles from the pulp to the concentrate lip. This paper critically analyses the current models of froth transportation in flotation, and examines the limitations of these models. The importance of froth rheology, which is the resistance to the froth flow towards the discharging weir, in determining froth transportation, is also highlighted."

Jan 1, 2014

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

"Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching experiments indicated that copper extraction rate was accelerated by cupric and ferrous ions , and was higher at potentials below a critical value (critical potential) in the presence of these ions. This was in good agreement with the results of electrochemical measurements, i.e. in the anodic polarization curves for a chalcopyrite electrode, active-passive behavior was observed when cupric and ferrous ions co-exist, but the activation at low potential did not occur without these ions (Figure 1). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials.These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model."

Jan 1, 2003

By E. Kusaka, M. EL Salmawy

"The electrokinetic behavior of EL Maghara coal has been investigated in the presence of nonyl and octyl nonionic surfactants containing polyethoxy of different sizes with trade names of Triton-X100 (TX-100), Triton-X 705 (TX-705), Triton WR-1339 (TWR-1339) and Brij 58. The electrokinetic behavior was determined by zeta potential measurements. Zeta potential measurements were conducted by Laser-Doppler electrophoresis technique using zetamaster. The results show that the zeta potential of Egyptian coal varies with pH value, the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. It was found that the polymeric surfactants reduce the negative values of zeta potential of coal. The shift of PZC of coal upon deashing appears to be closely relevant to silicate mineral removal."

Jan 1, 2014

By Graeme J. Jameson

"When mineral particles are floated in a mechanical flotation cell, it is found that the rate constant, after reaching a maximum value, starts to decline as particle size increases. It had been thought that the reduction in rate constant had been due to the increased prevalence of composite particles in natural ores, for larger particles. However, Jameson (2012) showed that the rate constant for composites is certainly a function of the surface liberation, but the reduction in flotation rate is independent of particle size. Thus all particles are equally affected by reduced surface liberation, independently of their size. He further argued that the classical peak observed in the rate constant with increasing particle size, is a function of machine hydrodynamics. Thus in mechanical cells, the peak may be due to the high energy dissipation rate and its effects on the detachment of particles from bubbles (Goel and Jameson, 2012). Consequently, in a different flotation environment, it may be possible to float large composite particles that cannot be floated in mechanical cells. This paper describes the flotation of large composite particles in a fluidized bed flotation cell. The particles to be floated are fed to a column in which there is a continuous upflow of liquid. A conventional froth layer of controlled depth is formed at the top of the vessel. A fluidized bed of particles is established which provides a gentle environment for the contacting of large particles with bubbles. An example is given where a porphyry copper ore was prepared at a top size of 710 µm, and floated with conventional collector (PAX) and frother (MIBC). The concentrate was separated into size fractions and examined by photography. Composites were observed at all size fractions, but above 400 µm, all particles were composites. The implications for future flotation circuits will be described."

Jan 1, 2014

Sedimentary deposits such as sandstone are formed by the aggregation of cemented sand grains. Phosphates and laterite present similar aggregation of mineral grains. Grains and cement have different mineralogy and chemical characteristics. During size reduction through crushing or coarse grinding, the rocks are crumbled. Mineral grains and cement are then liberated, and the produced size distribution reflects their ?natural size distribution?. Mathematical modelling of these concomitant effects of crumbling and mineral liberation necessitates a specific material description and the adaptation of the commonly used theories of breakage kinetics and population balance. The coarse particles are mainly agglomerates made of mineral grains and cement particles whereas the fine particles are grains and cement with a natural grain size distribution. The population balance between the different particle size and particle types during size reduction takes into account the breakage rate and the progeny size distribution. The breakage rate can be described by a simple probability function or by a first order kinetics whereas the progeny size distribution is described by a breakage matrix. The model proposed here considers that the agglomerates will produce other agglomerated particles, liberated grains and cement particles; the two latter having their natural size distribution. The liberated grains and cement particles are subject to size reduction and follow the most commonly used theory of breakage. The present paper describes the theoretical approach of the concomitant crumbling and liberation effects. The application to a mathematical model for the cone crusher is presented. The advantage of such approach is then demonstrated through a simulation study for the optimisation of a crushing plant. Keywords: mineral liberation, modelling, crushing, sedimentary ore

Sep 1, 2012

By N. Kgabi, F. B. Waanders, E. Vinken, A. Mans

"Mössbauer and SEM identification of the iron mineral phases present in South African coal fractions from the Free State, Gauteng, Mmpumalanga, Natal and Waterberg coal fields, as well as from ash samples from coal used in the Lethabo power plant, containing a large amount of inorganic matter, was conducted. The iron is mainly associated with sulphur in the mineral but the amounts of these and other minerals vary considerably in coals from diverse origins. By means of Mössbauer analyses the iron bearing minerals were identified as pyrite, jarosite, illite and ankerite. In the SEM analyses quartz, associated with various clay minerals was identified with differences in abundance found between the coals from the different locations.The fly ash, produced at the high combustion temperatures in the power plant, gave rise to a spectrum, typical of a glass. SEM analyses showed that agglo- meration of the fly ash was due to the presence of Ca in the coal. The lab. produced fly ash was combusted at temperatures ranging from 200-1 200°C and the pyrite changed partially to hematite and partly into the glass due to the presence of the quarts and the clay minerals. A similar spectrum as the power plant fly ash spectrum was obtained.In the weathering experiments the pyrite changed to a sulphate component in a very short time during air drying."

Jan 1, 2003

By Stuart Simpson

The biggest environmental challenge in mining is the management of mine tailings. Deep----sea tailings placement (DTSP) is practiced where the environmental impacts are predicted to be less than the impacts of tailings storage facilities on land. However, DSTP is often highly controversial owing to the challenges in assessing the impacts in deep water environments and potential long----term impacts beyond the proposed tailings footprint. It is well recognized that total contaminant concentrations are often poor predictors of the risk posed by contaminants in sediments. Metals within tailings are mostly present in highly mineralised forms that are typically much less bioavailable to organisms when compared to other common anthropogenic metals. Thus while metal concentrations in tailings can often appear alarmingly high, when compared to sediment quality guidelines (SQGs) used for assessing common urban and industrial impacts, the bioavailability is typically low. Although now well----embedded within risk----based sediment quality assessment frameworks, contaminant bioavailability is still often overlooked in the management of contaminated sediments. In this presentation, we assess and demonstrate the low bioavailability and chronic ecotoxicology of mineral----rich tailings to two benthic invertebrates, recognized for their sensitivity to metals: impairment of reproduction of the amphipod, Melita plumulosa, and the harpacticoid copepod, Nitocra spinipes. We demonstrate that the metal exposure from mine tailings is low when total concentrations are considered, and that the dose to the organism and toxic response observed is highly dependent on contaminant bioavailability. We discuss a range of approaches for the effective incorporation of metal bioavailability when applying SQGs or setting site-specific management limits for mine tailings in marine environments. While proposed DSTP operations require a high level of environmental scrutiny and monitoring during operation and post-closure, environmentally sustainable operations may be achieved when the bioavailable forms of metals within tailings remain below suitable management limits.

Jan 1, 2014

By Janusz S. Laskowski

"Frothers offered by different manufacturers are marketed with some information on their chemical and physical properties (e.g. density, viscosity, color, water-solubility, safety/toxicity, etc.). But frothers are used in flotation to generate fine bubbles and to stabilize the forth, and this information is only provided in a very qualitative description of the visual appearance of bubbles and froths. The terms “powerful” and “selective”, which have been commonly used to characterize frothers, have intuitive rather than scientific meaning.This paper introduces the DFI (Dynamic Foamability Index) plotted vs. CCC (Critical Coalescence Concentration) diagrams to classify flotation frothers (Fig. 1). The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers."

Jan 1, 2003

By Häkkinen Antti, Salmimies Riina, Matveinen Maria

"Tailings generated during the upgrading of ore present a major challenge for the mineral processing industry. On one hand, the processing of tailings requires added capital input. On the other hand, increased difficulties in obtaining permits for dams and landfilling and increased costs associated with storage and tailings management also result in increased costs. To promote sustainability and make tailings management economical, added value must be generated from the waste material. This might be possible through the recovery of the metal values in the waste. This work discusses the possibilities of recovering metals from multimetal tailings through leaching in a stirred tank. The characteristics of the tailings are crucial and the distribution of the metals within the different size fractions is used to identify the most attractive route for the hydrometallurgical step. Leaching of nickel and copper is further investigated using acids at different concentrations. The leaching of base metals is possible at acidic conditions. Increased temperature and concentration of the leaching agent promote the dissolution of the metals, as could be expected. With simultaneous dissolution of several metals the dissolution mechanisms are difficult to identify. Furthermore, as several metals, not all of them being target elements, are leached another challenge arises from the selective recovery of those metals from the liquid phase."

Jan 1, 2014

By Remmerswaal, U. Boin, M. B. G. Castro

"To design sustainable products that can be recycled with high resource efficiency, low environmental impact and economic feasibility, the choice of materials and materials combinations, made in the design stage, is fundamental. The products we design, manufacture and use now will be the resources of the future. Designers are able to select materials for a product according to the many functional requirements they must fulfil. But they have a limited knowledge of the recycling processes and its requirements regarding quality of the secondary material streams. Resource Engineers have to manage the processing of these streams, that are becoming more complex with the increasing variety of materials and decreasing size of components. After mechanical separation of the materials streams resulting from shredding of EOL (endof- life) products, there is always a degree of contamination, from two possible causes:Incomplete liberation: the bonds between different materials combined in a component are not completely destroyed by shredding, resulting in some particles containing two or more materials attached;Separation efficiency: the mechanical separation processes are not able to separate perfectly the many material particles; there are always a number of foreign particles in the recovered streams.Sometimes, those contaminants cannot be removed by the industrial metallurgic recycling processes, and a more serious problem occurs when the contamination levels compromise the recycling of the material stream by lowering its quality (i.e. the properties of the recycled material will be lower due to the contamination). As a consequence, the material must be diluted in virgin raw material and/or used in a less demanding application (downgrading), causing resource depletion and increased energy use, waste production and recycling costs. In order to make the best choice of materials combinations for a product, a systematic approach is necessary, that can close the gap between the knowledge areas of Product Design and Recycling Technology."

Jan 1, 2003

By Ray Everson, Henry Kasaini

"Adsorption of Pd (II) anions on the surface of activated carbon (Norit 0.8) occurred at high proton concentration (0.01 – 2.5M, HCl) in the feed and averaged 27 mg/g. The adsorption process was interpreted in terms of surface ionisation and adsorption model. Enthalpy of adsorption averaged 0.4 kJ/mole indicative of an instantaneous physical adsorption process. We found that the Toth isotherm fit the adsorption data fairly accurately. A combination of the Langmuir and Freundlich equations yields an effective three-parameter Toth equation (1) which is frequently used to describe adsorption on heterogeneous surfaces.Figure 1 shows the comparison between experimental results and the model isotherms. We found that Langmuir isotherms underestimated the adsorption capacity on the porous surface while the Freundlich isotherm overestimated adsorption. Furthermore, the surface coverage at equilibrium was well described by both the Langmuir and Toth isotherms. But, Freundlich isotherm predicted a surface fraction coverage that was higher than unit. Based on better prediction of surface coverage and a reasonable fit to adsorption data, we concluded that the Toth isotherm best described the adsorption data of palladium. The adsorption process was limited by mass transfer resistance through the external film. We estimated the rate constant from equation (2), where e, ?b, and rp are porosity, fluid density and particle radius, respectively"

Jan 1, 2003