Search Documents

By Francisco Vicuña, Miguel Becerra, Nelson Iglesias

"The following article presents the development of a dynamic tool for the estimation of Jb/Jc rate (ball filling level / total load filling level) of a SAG mil operating in a single stage mode. Using the methodology detailed in this article, it is now possible to have a dynamic estimation tool in the operation, which enables strategic decision making and achieving a continuous development in process optimization. The estimating of the load filling level (Jc) was conducted using a power model, which in this case corresponds to the C-Model developed by (Morrell, 1993) that was calibrated by measuring the load filling levels (Jc) and balls (Jb) using the FARO laser scanning technology by means of Grind-Out and Crash-Stop procedures during the year 2013 and 2014. Finally, to estimate the dynamic filling level of full charge, Jc, three independent models were developed that allowed to feed the adjusted power model: •,SAG mill discharge grate slot wear model •,SAG mill internal volume wear model •,Ball filling level estimation model."

Jan 1, 2014

By Andrzej Luszczkiewicz, Magdalena Duchnowska, Jan Drzymala

A selected flotation system of beneficiation of the copper ore at KGHM Polska Miedz S.A. has been analyzed in the article. It was found that a proper assessment of upgrading must be based on two elements, that is the upgrading process selectivity and working point of the considered flotation unit, both determined, preferentially by means of the Fuerstenau recovery-recovery upgrading curve. The Cu recovery - non-Cu components recovery upgrading curve was selected for calculations because its background lines (no separation and ideal separation) are insensitive to changes in the grade of feed of the processed material. This approach allows a comparison of upgrading results for feeds having different grade, being upgraded in various flotation machines and under different physicochemical conditions. It was shown in the paper that the main criterion for comparison of two working in parallel systems is selectivity of upgrading. However, when two flotation machines, despite of the same selectivity, produce concentrate and tailing of different grades, it is necessary to analyze their working points using upgrading curves. The proper position of the working point depends on the criterion imposed on the process and is a result of not only basic parameters of the upgrading process such as feed, concentrate and tailing grades but also on economic parameters such as costs associated with the production of concentrates and the time needed for their production.

Jan 1, 2014

By Vladimir Vigdergauz, Sergey Kondratiev

The paper reviews the existing criteria of the formation of particle-bubble aggregates during flotation. It is shown that predictions obtained by these criteria do not completely fit to the interaction between mineral particles and air bubbles. Experimental results of the studies into the influence exerted by molecular forms of collectors on the particle-bubble interaction are reported. Rate of dry spot expansion on the surface of pyrite with various combinations of chemically and physically adsorbed xanthate are examined. It is shown that molecular forms of collectors accelerate the rate of dry spot expansion on the mineral surface after the local rupture of the water film between particle and air bubble. The authors come to a conclusion that the molecular forms of collectors remove water from the interlayer between mineral particle and air bubble during their contact. Similarities of the proposed mechanism with the action of ion-molecular associates of fatty acids and amines are discussed. Reagents with high surface pressure and rate of spreading at the water-bubble interface are required for the effective interfacial dewatering. It is concluded that the value of surface pressure can serve as the criterion for efficiency of physically adsorbed reagents. The low surface pressure indicates weak collecting ability but high selectivity of the collector. Therefore, the presence of the molecular forms of collectors in the sorption layer is the necessary condition for formation of particle-bubble aggregates, and comparison of the surface tensions of collectors could be recommended as the estimation criterion of their flotation activity and selectivity.

Jan 1, 2014

By Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"The process of grinding in drum mills is directly dependent on the dynamic forces occuring in the free movement of the grinding bodies in the volume. The subject of discussion are the potential impacts between grinding bodies having different shape and equal weight in a drum mill that has a diameter of 1200 mm. The study utilised ball grinding bodies having a diameter of 120 mm and tetraballpebs having a conditional diameter of 120 mm. The study was carried out using the Solid Works Simulation software. The following cases were examined: • Impact between two identical grinding bodies; • Impact between a grinding body and the shell surface. The study provided numerical values for impact force, kinetic energy of impact, linear speed of impact, linear displacment of the center of gravity and duration of impact deformation. The impact force of the balls is approximately 179000 N. The impact force of the tetraballpebs with typical vertices, edges and spherical surfaces depending on the area of impact is 177000 to 185000 N. Upon impact between two spherical surfaces of tetraballpebs, the contact area is 263.55 mm2, which is more than twice the contact area upon impact between two balls, which is 114.39 mm2. This determines better conditions for the transmission of kinetic energy by reducing opportunities for overgrinding."

Jan 1, 2014

By Martin Rudolph

"Flotation is without a doubt one of the major processes for the separation of fine minerals and it has been applied for more than a century. A key task of a successful flotation separation is to find the proper chemical treatment to selectively hydrophobize and thus float a certain mineral phase using molecules or ions referred to as collectors, depressants, regulators and frothers. Commonly floatability is determined by microflotation tests using the Hallimond tube with pure mineral phases. This method however requires the pure mineral phase which is very often not even taken from the same deposit which is going to be processed. In this paper we present a new approach to in-situ determine and even map the floatability of finely disseminated mineral phases within cross-sections of an ore. It is based on measuring hydrophobic effects using colloidal probe atomic force microscopy with a hydrophobic polystyrene probe based on force spectroscopy with a lateral resolution of only a few nanometers. Coupled confocal Raman spectroscopy on the same locality enables the identification of the mineral phase. We present the working principles of the method and show which signals in the force spectra characteristic for hydrophobic interactions can be used to define floatability and which can then be mapped as single quantities, e.g. jump-into-contact events due to nanobubble occurrence or parameters of the long range interaction curves most probably due to capillary effects. A finely grained silicate ore containing the valuable rare earth mineral eudialyte from southern Sweden as well as pure samples of magnetite are presented as substrates to demonstrate the capability of this new approach. This method will not only help to find the proper flotation chemistry but it can furthermore help in researching and unravelling problems of floatability within similar mineral phases."

Jan 1, 2014

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By M. Wright, A. H. Mwale

This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered.

Jan 1, 2003

By P. Somasundaran, Tarun Bhambhani, S. Murthy Khandrika, Partha Patra, D. Nagaraj

Fine and ultrafine mineral particles, particularly if, altered mineralogically, can have detrimental effects on selective separation of minerals. Behaviour of altered mineral fines has been investigated in this work by studying the effects of weathered silicate slimes on the selective separation of copper minerals, particularly with focues on effect of the pulp rheological behaviour, which plays a governing role in the process. Physicochemical properties of these altered silicates fines such as morphology and surface charge are proposed to be responsible for the adverse rheological effects and resultant selective separation. Here, the effect of a number of problematic aspects such as water chemistry, froth stability, physicochemical aspects of gangue mineral aggregates on flotation sub-processes has been studied. Processing problems owing to the physical aspects of the gangue minerals, shape and morphology, are primarily due to uncharacteristic increase in the pulp viscosity. While problematic aspects other than impact of pulp rheological behaviour can interfere with each other in their contributions to how they affect the sub-processes, effects owing to pulp rheological behaviour have a direct impact on the flotation performance. Subtle increase in pulp viscosity can interfere with sub-processes in flotation leading to decrease in recovery and grade, and it is difficult to assess the effects due to such subtle changes. Reagent based strategies to overcome the problematic aspects has been explored here.

Jan 1, 2014

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By Kilian Neubert, Wotruba. Hermann, Lars Weitkämper

Metallurgical slags are produced in large quantities all around the world as a result of smelting, refining or alloying processes applied to metals, ores and recycling material. The slag phase serves different purposes in metallurgical processes. It prevents heat losses and protects the metal phases from contaminations and absorbs gangue and extracted impurities. Due to achievable metallurgical efficiencies certain amounts of valuable metal contents always remain in the residual slag. Recycling of these metallurgical slags has several positive effects, such as optimized ecological and economical compliance of the producing industry. If recycled metal contents can be reintroduced into existing processes, required inputs of raw material can be lowered. High metal prices enable the economic recovery of metal contents in metallurgical slags by applying different non-metallurgical processing methods. Conventional processing of metallurgical slags utilizes processes such as hand picking, selective comminution, screening and magnetic separation. Those state of the art processing techniques have limitations in terms of achievable metal recoveries and required energy demand. The approach for an optimized processing of metallurgical slags targets enhanced metal recoveries in combination with lower specific treatment costs. Processes such as coarse and ultrafine density separation, as well as sensor-based sorting as a pre-concentration stage are used to enable an efficient recovery of metal contents in slags. By applying these methods a completely dry working process is possible. This paper reviews the commonly used methods and describes approaches for innovative processing of metallurgical slags to enhance metal recoveries. Focus of this paper is laid on sensor-based sorting as well as on processes for dry density separation.

Jan 1, 2014

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change due to the complex interdependence of metals, both in production and recovery, and the strong path dependency of industry and infrastructure development. Therefore, models for dynamic simulation were constructed that allow the specification and evaluation of the metal process network and waste management infrastructure ‘products’ over a longer time span. The model has been constructed using a bottom-up approach, to enable assessment of the environmental aspects of metallurgy and to simulate changes in the system structure and technology, i.e. from reactor or individual process step up to integrated material cycles. The model comprises hierarchical mass balances and linear models of individual processes and sub-processes. Thus, at lower system aggregate levels an increasing level of technical detail is represented. Data reconciliation has been used literature data on process feed, products and residue composition to calculate representative and reliable split factors around each (sub-)process. World production figures on process capacity and recovery rates are be used to calculate the relative contribution of processes. The dynamic map is illustrated with a case on the introduction of lead-free solder.

Jan 1, 2003

In this study, the effect of different regrinding conditions on the depression of fine pyrite at the cleaner stage was investigated. The regrinding condition was manipulated by different grinding media (stainless steel and mild steel). It was found that, after regrinding with mild steel grinding media, the flotation recovery of pyrite is much lower than with stainless steel grinding media, and it is more difficult to restore by adding more collector. This means, regrinding with mild steel grinding media may depress the pyrite flotation more strongly. The copper activation of pyrite during regrinding was also studied. It was found, that the mild steel grinding media is more beneficial to copper activation than stainless steel media. Additionally, the analysis of pyrite recovery based on the particle size indicated, that the fine particles are more susceptible to different grinding environments than intermediate and coarse particles and therefore are more easily depressed with a much lower flotation recovery.

Sep 1, 2012

By P. Somasundaran, Tarun Bhambhani, D. R. Nagaraj, P. Patra

"Certain non-sulfide gangue minerals are known to have a detrimental impact on flotation performance. When present in large amounts, they can negatively affect recoveries, grades and throughput at current operations, and dictate the viability and economics of a greenfield project. While the problem has been investigated for a long period of time, a scientific understanding of the mechanisms by which these minerals affect performance has not been obtained, and no acceptable solutions have been developed. This study focused on the role of physical aspects (e.g. shape, size and morphology) of these minerals as the underlying factors for poor performance. Flotation tests were conducted using model mineral systems to understand the impact of one phyllosilicate mineral (muscovite) on flotation kinetics, recoveries and grades. The study reveals that there is minimal impact on flotation kinetics, no impact on recoveries, but a very strong detrimental impact on concentrate grade. The traditional mechanisms of transport such as true flotation and entrainment are not sufficient in describing the extent of transport. The transport is attributed to the unique platy morphology of muscovite, which allows for action of buoyancy forces. Data also shows that the muscovite transport to the froth phase depends on particle size; coarser sized muscovite (100-150@) report to the froth phase in much larger amounts than medium sized muscovite (50-100@). At finer size fractions (<50@) the transport is also increased, and this is likely due to entrainment."

Jan 1, 2014

By P. Chris Pistorius, Johannes Sono, Rossouw Sono, J. J. Kobus

Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. These differences were highlighted when a plant which processes titaniferous magnetite had to change to different coal types after decades of operation. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. Direct reduction was evaluated by isothermal experiments using a packed bed of ore and coal, measuring the off-gas composition to determine reaction rates and departure from equilibrium. These indicated reduction to be under mixed control, and quite sensitive to temperature (confirming that the coal reactivity is of importance). An aspect of electrical smelting was assessed by determining dissolution rates of the coal in molten iron at 1550°C. Dissolution rates did correlate with differences in coal structure, as determined by X-ray diffraction, with the more ordered ("more crystalline") coal dissolving faster. The conclusion is that the coal which is more reactive during direct reduction is less reactive during dissolution. However, it is concluded that controlling the temperature during direct reduction offers a feasible method to reconcile the two process steps.

Jan 1, 2003

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Christopher Greet, Alfred Van den Bosch

"A range of media alloys with different chromium content has been developed for different milling applications. When selecting the grinding media alloy for a specific application, consideration must be given to the mineralogy of the ore as well as the water chemistry and mill operating conditions. The paper describes the influence of the microstructure of the alloy on the wear resistance and the influence of the chrome content on the pulp chemistry and downstream processing. It also provides information about the in-house tools which Magotteaux have developed to predict the media wear rate with different chromium content alloys and predict their flotation efficiencies that can be expected when the right alloy is selected for a particular application."

Jan 1, 2014

By Johannes Käppeler, Alexander Weh, Harald Giese, Klaas van der Wielen

"High voltage breakage is a novel comminution technology that shows considerable potential for various applications in mineral processing and recycling. It relies on highly energetic electrical pulses to induce electrical explosions in rocks, causing the formation of plasma channels and powerful shockwaves that result in fracturing and fragmentation of particles. There has been considerable interest in this technology for its ability to weaken rocks and preferentially liberate target minerals, as previously demonstrated by other authors. Weakening has the potential to significantly reduce energy consumption during comminution, or alternatively, increase throughput of a circuit. Better liberation may yield an improved concentrate grade and/or recovery, reduce fines losses to tailings or increase the grind size required for liberation, thereby also reducing energy requirements. This review aims to increase general awareness of this technology, and promote further research into it by providing a general summary of the theory underlying high voltage breakage, as well as the envisaged applications of this novel technology. A brief history of the technology is presented before progressing onto the physics underlying the electrical and geomechanical aspects of high voltage breakage. Key results regarding weakening and liberation are discussed, and some mention is made of current challenges and planned developments to increase the throughput of high voltage breakage units to the level where it can be integrated into new and existing processing circuits."

Jan 1, 2014

By Y. H. Hu, X. X. Zhang, Z. F. Dai, H. J. Huang, Q. S. Huang

"In order to get a more comprehensive understanding of the interaction of fine fluorite particles and bubbles, the electro-flotation was conducted, a high speed CCD was used to determine the bubble size distribution, and the results were analyzed using the models of collision and attachment. The electro-flotation was performed in a modified Hallimond tube. The results show that for different fluorite with size of 0 -10µm, 10 -38µm, 38-74um, there is a matching range between the different particle sizes and cathode aperture size (38um, 38um, 74um) to reach highest recovery. In addition, improving the concentration of collector is benefit for the flotation recovery due to the ability of collector to decrease the bubble size and prevent the merger of bubbles. Furthermore, theoretical calculation of collision, adhesion probability and collection probability is in agreement with the experimental data for electro-flotation recovery of fluorite.INTRODUCTIONFluorite is widely distributed, and has been found in more than 40 countries around the world. As fluorite minerals are easy to float, flotation is used as the best method of the current recovery of fluorite (Yang and Ai, 2016; Chen et al., 2017). In the field of mineral processing, the flotation of fine particles is particularly difficult, caused by the small quality and large surface (Sun et al., 2006). Flotation is now considered to contain three subprocesses, including the collision, attachment and detachment between the particles and bubbles (Sun et al., 2011). The collision of particles with bubbles is related to factors such as particle size and density, bubble size, bubble rise rate (Qin et al., 2012). Zongfu Dai et al. (2000) summarized the particle-bubble collisions models in detail and compared the experiment results with the model predictions. However, particle-bubble interactions occur in complex and turbulent flotation environments (Xing et al., 2017). Both thermodynamics and dynamic factors affect the adhesion of particles on bubbles surface (Schulze, 1989; Shahbazi et al., 2010). Scheludko et al. (1976) believes that the necessary condition for successful adhesion of particles on bubbles is that the contact time is greater than the induction time. The probability of adhesion between particles and bubbles increases with the increase of bubble size, but if the particle size is too small, the probability of adhesion decreases instead (Ren, et al. 2014; Norori- McCormac et al., 2017). After the particles adhere to the bubble surface, the particles will slide down to the bottom of the bubble due to gravity. At this point, the gravity, inertial centrifugal force and fluid force promote the desorption of particles from the bubble surface, while the surface tension, surface hydrophobic force maintain the stability of particles-bubble combination (Ralston et al.,2017). In addition, in the process of rising to the foam layer, desorption can also occurs. The purpose of this study is to observe the flotation behavior of fine fluorite with different size and to get a more comprehensive understanding of the interaction of fine fluorite particles and bubbles."

Jan 1, 2018