Search Documents

By Chiharu Tokoro

Acid Mine Drainage (AMD), high acid water containing heavy metals discharged from mines, has been recognized as major cause of mine pollution. In Japan, the government spends billions of yen every year to prevent pollution caused by AMD in about 80 abandoned mines. It is widely recognized that the treatment could continue for long decades or an even century. However, costs and environmental loads are uncertain during the treatment because a predictive model for the quality of AMD, the dosage of neutralizer, and the amount of sludge that is applicable for abandoned mines with limited data has not yet been established. In this study, a two-steps predictive model for solution composition and neutralization chemical requirements of AMD in future was constructed based on the geochemical modeling. Requisite input data of the model was the past historical water quality data from AMD monitoring, such as metal concentration and pH in the solution, instead of the sample rocks as other conventional prediction methods. In the first step, solution composition of AMD in the future was extrapolated from the available historical data using geochemical simulation considering the first order kinetics for the mineral dissolution. In the second step, neutralizer dosage and sludge generation in the future was predicted based on the geochemical simulation supposing the chemical equilibrium and oxidation state for all of elements in the solution. Based on case studies of two abandoned mines in Japan, solution composition, neutralizer dosage and sludge generation were estimated. The results of this study demonstrate the effectiveness of our model for the prediction of AMD quality and chemical requirements of neutralization treatment after mine closing. The model is useful for the estimation of the neutralizer dosage and the sludge volume in abandoned mines with limited data. Keywords: acid mine drainage, predictive model, geochemical modeling, first order kinetics, water monitoring

Sep 1, 2012

By Tomás Vargas

Treatment of copper sulphides minerals via leaching-solvent extraction-electrowining (lix-sx-ew) have been for years the process scheme proposed from hydrometallurgy as an alternative to the conventional flotation-smelting route. Many different hydrometallurgical technologies of this type have been proposed, investigated and tested over the years, but until today none of them has come close to endanger the predominance of the flotation-smelting route in the copper industry. However, bioleaching introduced an important breakthrough in this context as this technology enabled the alternative hydrometallurgical treatment of secondary copper sulfide ores and low grade ores by applying heap bioleaching processes. Extension of its application to primary copper ores have been limited until now by the nature of chalcopyrite which is very refractory to leaching. However, important improvements are expected by using of improved designs that enable to operate at high temperature ranges where copper is leached faster under the catalytic action of thermophile microorganisms. The present work analyzes future scenarios for the application of this technology either in heaps or in-situ, which can become very attractive as copper can be produced reducing drastically the energy consumption associated to the mining, crushing and grinding stages.

Jan 1, 2014

By Ricardo Duque-Soto, Gonzalo Montes-Atenas

The depletion of water resources has posed an enormous challenge to the continuity of many mine sites, particularly those located in arid zones worldwide. In Chile, the use of seawater has been foreseen as one possibility to solve this problem. Nevertheless, the direct use of high ionic strength solutions such as those present in the sea has been found to have some drawbacks. Specifically, rhe extraction of copper from complex ores using high ionic strength solutions such as that of seawater has become one of the most relevant topics in the field of copper hydrometallurgy. This study aims to determine the effect of the degree of salinity on copper extraction kinetics in mixed oxide-sulfide ores. A leach protocol was implemented to study the extraction kinetics, varying the degree of salinity of the medium and the temperature. A thermodynamic model was developed to explain differences in the metal extraction. It was found that the ionic strength impacted positively the copper extraction, probably due to the reduction of the effective concentration in solution due to ionic interactions enhancing the diffusive mass transport of copper ions. This effect is observed to be enhanced when up to an overall salinity values close to 20gpl.

Jan 1, 2014

By Jorge Menacho

"A typical Chilean producer in the Large Copper Mining Industry today is characterized by high production level with economical results decreasing but still attractive. Operational activities are developed within a low-productivity environment, with high cost and complex relationship between the company and communities, government authorities, providers, clients and their own workers. Decreasing copper grades and limited availability of energy, water and workforce are structural problems which require the State intervention in collaboration with the relevant actors and benefits would be evident in the middle or long term. Main opportunities in the short term are found in the sub optimal conditions we have at many plants today. Robust solutions to control existing operational management system as well as to supply systematic optimization options are needed. These should be oriented toward effective fulfillment of specific operational set points and also to reduce variability in crosscutting tasks. Solutions should include easy connectivity to existing information systems as well as to a suite of simulation and optimization tools settled in a highly interactive communication platform. Relevant issues include minimization of specific energy and fresh water consumption, maximization of the use and performance of critical equipments, minimization of damage to environment and control of effective application of good operational practices. Several specific examples are given."

Jan 1, 2014

By Camilo Uribe, Williams Calderón, Gonzalo Montes-Atenas

In industrial hydrometallurgical operations, the leaching process is often implemented via heap or dump leaching operations. During the pile up of these massive amounts particles a porous material is then formed. The manner it is constructed is crucial since it will define the permeability and other parameters determining the flowrate of leaching solution across the material. This study aims to estimate how the unsaturated permeability of the staked porous structure confined in a column-like geometry varies with and without particle size segregation. The piling up will be modeled using the Rocky® software. Different disposals of particle size distributions across the column will be simulated and their effect onto the overall column unsaturated permeability will be estimated. It was found that when the belt speed increased, the particle segregation in the column also increased. This condition is expected to improve the permeability of the porous structure in the column, probably due to the smaller compaction of larger particles when they are located at the base of the column and maintain a suitable porosity to permit leaching flowrates relatively high, suggesting better extraction results. The opposite was observed when small particles were preferentially located at the bottom of the column. These results are expected to provide an insight towards what is the best way to construct heaps and dumps.

Jan 1, 2014

By Daniela Campos, Aldo Casali, Gonzalo Montes-Atenas

The understanding of the effect of the major variables influencing the froth flotation performance may allow both to predict and to identify best operating conditions towards optimizing the process efficiency. The aim of this research work is to model the effect of dissolved oxygen onto froth flotation performance. Experimental pilot plant results were obtained from a continuous circuit consisting of a ball mill and a rougher bank of four flotation cells. A series of flotation experiments were run with different conditions of dissolved oxygen keeping constant most of other operating conditions. Variables difficult to control were measured or estimated. A set of mathematical models suggested in the published literature were tested. It was found that the copper recovery results were highly sensitive to the concentration of dissolved oxygen. The latter confirmed the reactions mechanisms associated to the collecting capabilities of current flotation reagents used in the flotation of copper sulfide ores. On the contrary, the results of molybdenum recovery varied non-linearly with changes in dissolved oxygen which could not be explained directly in terms of the computed specific rate constants. The error analysis confirmed that Klimpel continuous model exhibited the best specific rate constant correlation with molybdenum recovery data. Lastly, the classic particle force balance equations indicated that the adjustments of estimated mineral liberation with experimental data exhibited a turning point when passing from highly liberated to low liberated particles. The values of recovery for such turning point correlated well with the concentration of dissolved oxygen. The results indicated corrections due to changes in the dissolved oxygen must be incorporated in future froth flotation descriptions.

Jan 1, 2014

By Francisco Vicuña, Miguel Becerra, Gonzalo Montes-Atenas

"The optimization of the copper recovery from smelting slag by a process of comminution / flotation has been a widely discussed topic during the last few decades. Several studies covering the characterization of different types of slag, the impact of the slag cooling rate and of different flotation operating conditions on the flotation performance have been widely published. Currently, at El Soldado mine site (Angloamerican), there are large copper bearing slag deposits that can be a profitable alternative for the concentrator with capacity to treat this material. Under this process schema, the optimization of the flotation process to obtain better copper recoveries is a relevant topic of study. The aim of this study is to assess the efficiency of a sulfidation stage of a slag and to correlate that process with copper recoveries results in a flotation circuit. This article presents a detailed examination at both laboratory and plant scales of the slag sulfidation on the recovery of copper in the flotation process. The experimental methodology involves studying the effect of the sulfidation agent dosage, the pH, the particle size distribution of the flotation feed and the conditioning time. Furthermore, the performance of the sulfidation stage was analysed through the XPS analytical technique. It was observed that the sulfidation of particles in floatable size fractions correlated well with the increase in copper recovery. The results indicated that it is possible to increase between 2 to 4 points the total copper recovery with a sulfidation process implemented appropriately."

Jan 1, 2014

By C. Suazo, N. Mora

"The bubble size distribution plays a fundamental role in flotation kinetics. Nowadays it is possible to measure the bubble size distribution, gas holdup and superficial gas velocity by using specialized equipment developed for this purpose. In this article a methodology is presented for estimating the kinetic rate constant using a known particle and bubble size distributions. The attachment and detachment probabilities were modelled from three matrixes. The first matrix represents particle size distribution, the second was named the probability matrix, and the third is the bubble size distribution. Using laboratory data, it has been possible to estimate the flotation rate constant as a function of operating conditions and both the bubble and particle size distributions. The model tested at laboratory scale achieved a quadratic correlation coefficient equal to 0.97. This methodology could be used in the operation and control of the flotation, when in the near future we have industrial equipment that allows in-line measurement, in real time, of gas dispersion and bubble size distribution. knowing particle size distribution, it will be possible to manipulate the operating flotation cell conditions, in order to modify the bubble size distribution and find the bubble distribution that maximizes flotation kinetics. Furthermore, knowing the bubble size distribution, the grinding operator will be able to look for the particle size distribution that produces the maximum flotation kinetics. In order to do this, the operator will have to modify the solids percentage fed to the hydrocyclone cluster, modify the apex/vortex ratio, etc. Finally, this article shows that the maximum flotation speed is reached when the particle size distibution slope is equal to the bubble size distribution slope."

Jan 1, 2014

By Ronald Díaz

"Cerro Corona is a porphyry ore with different geometallurgical units and alterations produced by an extensive family of geological failures that have determined a special type of mineralization. With the increasing depth of the mine, it is estimated that the host rock will be less altered. Consequently, the ore will have a higher resistance to breakage accompanied by associated problems such as lower throughput. In light of this reality, various projects have been carried out with the objective to optimize mineral processing of ore with low clay content and high hardness, including reducing the blasting grid, increasing the load factor, using adequate mixtures of hard ore, reducing crusher settings, installing air guns in the transfer chutes, increasing ball charge, and changes in the lifter design, wear control in the hydrocyclones, syntonization of control logics, supervisor control of the SAG mil, characterization of feed ore, etc. However the most important factor was the teamwork between mine and plant personnel, aiming at common objectives for the company. These projects started in 2011, including characterization of mineralogical domains, breakage and blasting characteristics, and also a revision of the actual operating conditions in the crushing and grinding circuit. The development of different designs of the SAG mill lifters and the unloading grates, a 16% ball charge increase, improvements in the blasting process, reduction of the primary crusher setting, weight reduction on the feed lid, and variation of operational parameters, all allowed the company to achieve its objectives of maintaining impact control and steel recharge within the expected operational parameters. The achieved throughput is above design capacity, sustainable, and not without new challenges for maintaining and optimizing this production level."

Jan 1, 2014

By Rodrigo Ladrón, Gonzalo Rund, Gonzalo Montes-Atenas

Modelling ore comminution processes have been a highly fruitful scientific topic. The models have been proved to be largely dependent on the selected comminution technology. Among them, semiautogenous (SAG) mill technology has been widespread implemented in plants but no complete understanding of the mechanisms involved in the process is available. Tracing back in history, SAG models considered only some granulometric cut sizes such as the t10 and attempted to relate these parameters with the energy involved in the impact between particles. Other models evolved towards incorporating physical properties of the material being ground and the mill operating conditions. These material properties have assisted to obtain a more comprehensive description of the breakage mechanisms; nevertheless, the gathering of all known parameters still have not delivered a model able to describe the process. This may be a result of emergent properties or phenomena originated from interactions inside the process which are hard to predict turning the size reduction operation into a complex system. Cellular automata provide one answer to describe complex systems by following simple rules. The aim of this research work is to establish the preliminary rules of thumbs enabling the implementation of cellular automata able to predict the particle size distribution at the exit of a SAG mill. The methodology involved developing a simple 2D model of a ROM sample. Plant data from two mine sites were correctly described by a set of three rules: two rules describing the particle reduction and one rule associated with material transport across the mill. Further analysis related with expanding this model to 3D and its impact on the liberation of valuable material is also discussed.

Jan 1, 2014

By Paula Olea, Gonzalo Montes-Atenas

Froth flotation operation is a large tonnage process aiming at selectively separate economically valuable minerals from gangue material. The wellbeing of an industrial froth flotation operation has been historically assessed and understood in terms of many variables known to somehow affect the process performance. Among these variables, air dispersion have been pointed out as key to secure the correct transport of hydrophobic particles to the froth phase and, then, to the concentrate. One of the classic parameters assessed when evaluating the air dispersion in flotation tanks is the superficial gas velocity. Many reports have focused on studying the superficial air velocity profiles across the pulp phase and theories have been based on the fact that the measurements should be performed in the so called "quiescent zone", which is a volumetric region inside a flotation cell of difficult determination. The hypothesis behind this research work is that the reporting of particles to the concentrate would provide a better correlation with the effective air flowrate pattern created in the froth phase. The aim of this study, as a first step towards developing a flotation model fully froth phase-based, is to estimate the effective surface area used in a flotation cell derived from results obtained with a specific setup at laboratory scale. The methodology considers running a thin lateral flotation cell cut at different superficial air velocities, with and without particles. It was found a non-linear correlation between the superficial air flow rate and the characteristic distance between the vertical wall next to the cell lip and the cut point where the foam or froth flowrate almost stops contributing marginally to the overall amount of solid particles transferred to the concentrate. The presence of hydrophobic particles reduced the mobility of the froth phase reducing the characteristic distance.

Jan 1, 2014

By Claudia Ríos Figueroa, Gonzalo Montes-Atenas

"Among the many variables mentioned in the literature that may influence the froth flotation performance, particle size is perhaps one of the most renowned. Empirical knowledge has indicated that recovery of fine particles will inevitably drop below certain particle size threshold. Several processing alternatives have been suggested to improve the recovery of fine particles. Some of these initiatives have been reached the status of patents and other intellectual property related documents; however, there is still a disconnection between the scientific knowledge available and the industrial operations practicalities implemented to address this matter. In fact, in general terms, none of these ideas or processes concepts have become a final solution to this problem. At first glance, economical reasons may be argued as the main cause hindering the development of these and other ideas, but it would be an oversimplification as technical issues behind them are still themes to be discussed and sorted out. This study aims to review technical aspects behind scientific ideas and processes concepts suggested to solve the problem of low beneficiation of fine particles in froth flotation. The analysis was performed using the theory of inventive problem solving (TRIZ) which allows identifying technical gaps these initiatives have not considered or overlooked. Statistically the scientific databases indicates that reports on fine particles froth flotation only represented less than 50% of all reports involving fine particles processing. Most of the solutions derived from classic contradictions derived from bubbles and particles hydrodynamics only (reducing the bubble size or increasing the turbulence would increase the rate of bubble-particle aggregates formation but may reduce the recovery). This contradiction encompasses a small range of contradictions possible to be accounted and to be resolved. The method is expected to provide insights towards designing definitive solutions for the industry in this field."

Jan 1, 2014

By Nicolás Luis, Qi Liu, Gonzalo Montes-Atenas

"The prediction of froth flotation performance is still an unresolved topic. Classic industrial models based on particle size, elemental and mineralogical information provides recovery results with deviations that may become significant. One possible reason for this deviation may be the fact that the current liberation analysis provided by electron microscope based techniques does not take into account the outmost surface layer composition of liberated particles. In order to complete the description provided by the liberation analysis, other spectroscopy techniques measuring the extreme surface of the minerals can be tested. For instance, X-ray Photoelectron Spectroscopy (XPS) is a technique which measures the first tens of nanometers providing elemental composition over the particle surface and allows resolving the elemental associations present at the surface sample. However, this information needs to be statistically robust, reproducible and most importantly representative of what is occurring in the process. The aim of this research work is to develop a statistical model based on particle population to evaluate the feasibility of turning the XPS technique into a metallurgical tool. The model consists of classic statistical population arranged in a bed of heterogeneous particles with a known grade and mineral liberation. The simulations showed that the XPS results statistically followed a well-defined pattern. The statistical results were confronted with pilot plant results obtained from a rougher bank when processing a copper sulfide ore from a Chilean mine site. It was observed that the probability function distribution was in agreement with the experimental data. Further analysis on how the XPS results provide valuable information improve the computation of froth flotation recoveries is also discussed."

Jan 1, 2014

By Alejandro Rubio-Lopetegui, Gonzalo Montes-Atenas

The occurrence of Enargite (Cu3AsS4) in hydrometallurgical plants bears a number of challenges. One question lies on how Copper and Arsenic can be selectively extracted from the solid surface structure when immersed in aqueous solution. The leaching of Enargite in ambient conditions has been extensively studied; nevertheless, challenges regarding the process kinetics and surface structures enabling the extraction process remain ill-understood. Prior knowledge indicates that different conditions of pH, Eh, temperature, speciation of the aqueous phase or variations of these parameters defines the overall rate at which metals and other elements will be transferred to the solution. One aspect that the research studies have seldom addressed involves studying the main features of the surface structures formed during the leaching process at the outmost surface atomic layer. Such structures will mediate between the solid bulk and the solution to undertake subsequent stages of leaching process. The aim of this research work is to critically analyze the state of the art of Enargite electrochemistry from the mediator formation-dissolution mechanisms standpoint occurring at the mineral-solution interface. The most probable mediator species reported in the literature were found to be: Arsenolite and Sulfur (acidic media), Covellite (acidic and alkaline media) and Tenorite (alkaline media). As a result of this analysis, it was observed that the surface speciation was not in full agreement with the previous knowledge suggested to explain Enargite leaching reactions and, therefore, modified Eh-pH diagrams are presented. The acquired insights on the surface structures rising from the Enargite-aqueous solution interactions is further revised to provide new experimental protocols towards selectively separating Copper and Arsenic through hydrometallurgical paths.

Jan 1, 2014

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place. There are two possible mechanisms describing this process:(a) Gas nucleation, caused by nano bubbles inside the film.(b) Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals).Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film."

Jan 1, 2003

By David I. Verrelli, Peter T. L. Koh

"Recent experimental measurements of induction time made by direct observation with the ‘Milli-Timer’ indicated that angular particles were able to attach much more rapidly than spherical particles. There was around a tenfold difference in the respective induction periods for particle-bubble attachment. For industrial application, a more holistic comparison is needed, with the induction period for attachment being just one input. Over the years, CSIRO has developed a CFD-flotation model that incorporates both rigorous hydrodynamics, to simulate real industrial cell geometries, and a detailed model of the embedded flotation process, in which the induction period is an important parameter. We conducted transient modelling of batch flotation. First, spherical particles were modelled, as a ‘baseline’, for different particle sizes and levels of hydrophobicity. In the second set of results, the induction period was decreased by a factor of up to ten, simulating flotation of angular particles. Flotation recovery was found to depend upon induction period in a complex manner. For highly hydrophobic or fine particles, the induction period for spheres was already so low that recovery was limited by other factors (e.g. bubble-particle collision frequency). Further decreases in induction period, as for angular particles, did not have a significant effect on recovery in these cases. By contrast, when weakly hydrophobic or coarse particles were modelled, the recovery was predicted to be greatly enhanced for angular particles, in comparison to spheres. For these particles the induction period was limiting recovery, so that the flotation rate constant could be improved directly by reducing the induction period. This is consistent with batch flotation experiments using Ballotini reported earlier. Therefore, when dealing with weakly hydrophobic particles or relatively large particles that are to be floated, an enhancement can be expected for more angular particle shapes. In such cases, judicious specification of the grinding circuit may improve the overall efficiency."

Jan 1, 2014

By J. Gebhardt, D. McBride, M. Cross, S. Gilbert

Heap leaching of ores containing chalcopyrite offers a low cost option to treat low grade complex copper sulfide ore bodies. However, the slow leach kinetics of chalcopyrite at ambient conditions typically results in unacceptably low recoveries. As the mineralogy of new ore deposits becomes more complex and the effects of gangue chemistry exert a greater influence on copper sulfide leach behavior, the control of leach reaction chemistry becomes more critical. Computational fluid dynamics (CFD) technology has been useful in the capture of multi-phase interactions and provides a path to simulate complex fluid flow, gas and liquid phases, through the heap, along with species transport. Coupling the flow models with the reactive mineral dissolution, and the sometimes competing aqueous chemical and solid-liquid reactions, yields a comprehensive model of the heap leach process. The leach kinetics of chalcopyrite dissolution in heap conditions is examined, and the incorporation of chalcopyrite leach kinetics in the CFD model is described. The application of the model to investigate optimization of the heap is discussed.

Jan 1, 2014

By C. Dorfling, P. Albertyn

"Hydrometallurgical recovery of metals from printed circuit board waste typically involves multiple leaching stages; conventionally, base metals dissolution by mineral acids is followed by leaching of gold using cyanide or halide based lixiviants. Alternative lixiviants for gold leaching can reduce the potential hazardous nature of operation. The aim of this study was to investigate the feasibility of using thiosulfate as lixiviant for gold leaching from waste printed circuit boards. Batch leaching tests were performed to investigate the effects of thiosulfate concentration (0.1 – 0.2 M), ammonium concentration (0.2 – 0.4 M), pH (9 – 10.5), solids content (25 – 50 g/L), and copper content of the feed material on the gold leaching behavior. The concentrations of metals in liquid samples were determined by means of inductively coupled plasma atomic emission spectroscopy, and high pressure liquid chromatography was used to evaluate thiosulfate degradation/consumption. The ratio of thiosulfate to ammonia was found to have the most significant effect on the extent of gold leaching, with the best gold extraction observed at a ratio of 0.5 mole thiosulfate per mole ammonia. The lower pH range of 9 – 9.5 generally produced better Au leaching, while low copper extraction during the first stage base metal leaching stages has proven to be detrimental to gold leaching from the residue. Thiosulfate degradation/consumption increased and gold extraction decreased with higher residual copper in the feed. An optimum gold extraction of 78.5 % from base metal leach residue was achieved with 0.2 M thiosulfate, 0.4 M ammonia, and 0.02 M cupric ions at 25°C in the pH range 9 – 9.5.INTRODUCTION Background and Aim The recycling of e-waste is becoming increasingly important as it provides certain economic benefits apart from the obvious environmental benefits. Printed circuit boards (PCBs) are found in most forms of e-waste and contain especially high concentrations of base and precious metals. Hydrometallurgical processes are often considered for the recovery of valuable metals from PCBs; these processes normally implement several leaching stages to selectively recover certain metals."

Jan 1, 2018

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018