Search Documents

By Henk E. Brassinga

In Rotterdam a number of underground parking facilities have been built and are under development in the inner city, and in the suburbs. These parking facilities are located at already densely built areas. The design of these constructions has to take into account the impact of the building activities and that of the final construction on the surroundings. In this paper some examples of the different building methods of newly realized underground parking facilities are described, and problems that occurred during the construction are pointed out. In the soil conditions as present in Rotterdam the cost effectiveness of underground facilities can be improved by deepening the parking facility, and at the same time reducing the surface area so that the total parking volume remains constant. In this way the total volume of the diaphragm walls and the costs of the project is reduced.

Jan 1, 2006

By Han Xuanjiang

Through whole analysis of static testing piles information of a teaching building, this paper put for ward that when the ratioes of unload rebound amount to residual deformation and to total settlement reach the maximum, the testing load is selected as allowable capacity of single pile by camparing with the settlement in the practical engineering, it is proved that this method fits to practice, for other several projects, its also available. Therefore non-destructive testing pile method was improved, so all the tested piles can be reused as engineering piles.

Jan 1, 1991

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master', Giken 'Silent Piler" & Tosa 'Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their 'Push-Pull' system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling'. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By Deepak B. Deshpande

This paper enumerates various difficulties encountered in the design and construction of deep caisson foundations for the Second Bassein Creek Bridge constructed over a creek with very difficult site conditions. The designer of the bridge had anticipated the problems associated with the construction of large diameter floating caissons and limited the maximum size of caisson to 12.5m O.D. facilitated by the means of Shock Transmission Units (STUs). This is the first road bridge in India where STUs are installed to distribute seismic horizontal loads among piers installed with fixed and unidirectional bearings. Besides the usual difficulties of tilts, shifts, and sinking in the construction of floating caissons, the paper also describes a novel methodology used to retrieve a circular 12.5m O.D. caisson which had been swept away during a storm and stuck into the creek bed.

Jan 1, 2002

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By Raymond J. Castelli

The paper provides a general overview of the numerous types of earth retaining systems currently available, and organizes these various systems by several classification methods. These classifications can be used as a guide in identifying the appropriate type wall or walls for any specific project application. As a further aid in sorting through the numerous wall alternatives for a specific design or construction project application, the paper suggests a systematic approach for wall selection, and presents helpful charts summarizing the general advantages and disadvantages, and typical limitations for the currently available wall systems.

Jan 1, 2003

By W. J. Kingwell

Where the equipment, technique and materials are available for the construction of large diameter rock socketted piles, this is frequently the most economical and environmentally acceptable method of supporting very large concentrated foundation loads in geoglogically appropriate areas. This paper outlines the current approaches in Australia to design and installation of large diameter rock socketted piles. The equipment and procedures described generally reflect those developed or used by Vibro-Pile (Aust.), a company which, while installing the usual range of driven and bored piles, specializes in the design and construction of large diameter rock socketted piles and possesses special expertise in drilling in high strength rock. A high capacity crane attached drill for large diameter drilling in rock is briefly described. Discussed in detail are the construction techniques employed and structural and geomechanical design methods adopted.

Jan 1, 1989

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999

By M. England

Test equipment has been developed to record automatically both the displacement of the pile head and the load applied during a conventional maintained load pile test. Some systems also have, in addition, been fitted with the facility for maintaining the applied load, as set by the operator, at very constant levels. The advantages are both commercial and technical, but a well trained operator has to be in attendance to control the test. Since typical test specifications in the UK require more than 19 hours to complete, it became inevitable that at least one equipment operator remained on site to expedite the test for its duration. Although electronic measurement and data logging of load tests may be more safe than previous direct observation of dial gauges. A single person remaining on a construction site alone is not to be recommended, even if they are just supervising the test. Further development of the testing system produced equipment which will perform the entire test specification as required without operator intervention. To achieve this, full automation is employed. The patented method particularly addresses the safety requirements and by using additional sensors, detects any uncharacteristic behaviour of the pile under test or of the reaction system and the equipment takes appropriate action in a controlled and safe manner. The quality of test data returned from these automated systems is a key element when analysing pile behaviour with models such as CEMSOLVE? and TIMESETTM. These analysis methods often indicate ground disturbance resulting from installation technique and have allowed pile design to be optimised using actual field data rather than theoretical considerations alone. An additional feature is remote access, this allows the data recorded to be transferred and the progress of the test to be viewed from practically any location. This permits experts to view the data &apos;live&apos; and allows rapid diagnosis of any problems with the expected pile behaviour.

Jan 1, 2002

By Tomohide Takeyama, Yuki Yoshida, Masaki Kitazume

"Abstract A series of centrifuge model tests was conducted to investigate the failure pattern and stability of cement treated clay ground having an unsupported vertical slope. The model ground was subjected to monotonically increasing centrifugal acceleration until it failed due to the enhanced self-weight. The test results were compared with the numerical analyses in which the treated soil was simulated by the Smoothed Particle Hydrodynamics (SPH) method. In the simulation, the Dracker- Prager model is employed as the constitutive model. In order to simulate the brittle behavior of the cement treated soil, it is assumed that the unconfined strength is gradually reduced to a certain value which corresponds to the residual strength due to accumulated plastic strain. It was found that the simulation by using SPH method can express the brittle failure observed in the centrifuge model tests.IntroductionBecause of economical and environmental concerns it has become more difficult in recent years to obtain enough soil to construct reclaimed land for airports, electric power plants, manufacture plants and so on. On the other hand, it has become difficult to find and construct disposal sites for waste subsoil or dredged soil. These circumstances have encourage geotechnical engineers at present to use these poor quality materials as filling materials more than they were used one or two decades ago. Several soil admixture methods have been developed to improve their properties and to manufacture high quality fill materials.The deformation and strength characteristics of cement treated soils have been investigated in Japan, which have revealed that the treated soil is characterized by a brittle behavior with quite high compressive strength and quite small strain at failure, and the treated soil with relatively high strength shows tensile failure instead of shear failure. Regarding to evaluate the stability of structures adjacent to or buried in the treated ground, Kitazume (1998) and Kitazume et al. (2003) investigated the earth pressure of cement treated ground by the centrifuge model tests. And they emphasized that the failure pattern of the cement treated ground was much different from that of ordinary ground. After the Hyogoken- Nambu earthquake in 1995, many design codes for the seismic stability were revised in Japan, so that seismic stability must be evaluated more precisely. The dynamic earth pressure of ordinary grounds is usually calculated by a pseudo-static limit equilibrium method based on the Mononobe- Okabe’s method (Okabe, 1924; Mononobe and Matsuo, 1929). This calculation method is also applied to the cement treated ground, although its applicability has not been thoroughly clarified."

Jan 1, 2014

By D. E. Sherwood

Mr. Tamaro introduced his paper which concerned the construction of foundations for the buildings and related infrastructure of the World Financial Center on a reclaimed shoreline site at the Southern tip of Manhattan Island. This large project presented difficult design and construction problems, both geotechnical and structural. All structures were supported by foundations carried to rock. Two of the buildings were supported by conventional pier (pad) foundations constructed within diaphragm wall cofferdams. The remaining structures were supported by either piles to rock or caisson (large diameter) piles with socket depths drilled through the rock of up to 7.6 metres. Underground services, railway and proposed road tunnels all affected the installation of foundations. The proposed road tunnels for the new six lane &apos;Westway&apos; would involve an excavation 12 metres deep adjacent to and under three buildings. This problem was solved by an agreement that tower windloads would be taken by the tower foundations and not distributed through the basement walls. This was achieved by a system of battered caissons founded on the rock and arranged so that adjacent caissons were founded in different rock masses. Diaphragm walls were restrained using tie backs. Ground testing indicated an exposure to D.C. stray current corrosion of all underground construction. As a result all of the foundations were isolated from the ground by non-conductive materials. In the case of piles and caissons the reinforcing for the caisson was fully protected by concrete and all outside steel used for the installation of piling was considered sacrificial and not used in the computation of long term load carrying capacity.

Jan 1, 1991

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By Anthony H. Tawil

Modern, high-speed machines used in the manufacture of paper require foundations with stringent settlement constraints. To fulfill this requirement, caisson piles, extending into bedrock, were selected to support a paper machine in Baie Comeau for the Quebec North Shore Paper Company (QNSPCo.). This was the fourth machine in an existing paper mill, and its construction was part of an expansion program which included the building of associated structures such as a wood room and chip storage building, and other facilities, Figure 1. The paper mill in Baie Comeau, Quebec, is located in an area which has extensive deposits of sensitive marine clay which are transformed into a viscous liquid when disturbed by external forces such as the driving of piles. Loss of ground and soil disturbance as affected by piling activity assumed considerable importance in the design and construction of the caissons particularly in view of the proximity of existing plant facilities, including another paper machine.

Jan 1, 1987

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By Mario Terceros H., Bengt H. Fellenius

"ABSTRACTFour strain-gage instrumented bored piles were constructed in a sedimentary, dense to very dense, fine to medium sand in Santa Cruz, Bolivia. Two of the test piles were the normally used bored pile constructed with bentonite slurry and two piles were Bauer Full Displacement Pile (FDP). One of each pair was equipped with the Expander Body, an inflatable steel cylinder that on pressure-grouting provides an enlarged pile toe. Head-down static loading test were performed on three of the piles and a bidirectional test was performed on the fourth pile, a standard pile with Expander Body and a bidirectional cell placed immediately above the EB. The latter pile was tested in 3 phases. First by activating the cell, second, by a head-down test, and, third, by a repeat bidirectional cell test. The static loading tests proved the shaft resistance of the FDP pile to be about twice that of the standard bored pile and that the Expander Body more than doubled the toe stiffness. The strain-gage records showed that the standard bored piles had multiple bulges and neckings, which affected the evaluation of the axial stiffness and load distribution of the piles. The testing programme was used for a prediction event with 60 persons, ahead of the tests, submitting predictions of the load-movement curves for the test piles and also a capacity appraised from the curves.1. INTRODUCTIONOn April 23 - 26, 2013, the First International Conference and Seminar on Deep Foundations was held in Santa Cruz, Bolivia under the auspices of INCOTEC SRL, the UAGRM University, and the Bolivian Association of Civil Engineers and Chamber of Construction. To coincide with the conference, a research study on construction and static and dynamic testing of four instrumented bored piles was undertaken. To ""add spice"" to the conference, a prediction event was organized on the test programme. This paper presents the soil conditions at the site, the type and construction of the test piles, the outcome of the prediction event, and the results of the static tests.2. SOIL CONDITIONSGeotechnical studies comprising SPT and CPT tests with routine laboratory analysis were performed on recovered soil samples. Three SPT boreholes were put down at three of the locations of Pile TP1, TP2, and TP3, at 5.0 m distance from each other. The SPT procedure consisted of manual hoisting of the weight by three crew members pulling on ropes over a pulley supported by a tripod and letting the weight fall by gravity. The groundwater table lies at 3.5 m depth.Figure 1 shows diagrams of the SPT N-indices and the distribution of water content in the three boreholes. The SPT-indices show the soil density to be compact. The average water content is about 15 %, plus-minus a few percent."

Jan 1, 2014

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By J. Moskowitz

Construction of the new JFK International Airport Light Rail System (LRS) began in 1998 with a pre-construction load test program. This $1.2 billion design-build project consists of approximately 13 kilometers of elevated twin rail. The elevated rail system is supported on nearly 500 piers requiring deep foundations. The presence of underlying compressible and liquefiable soils as well as space constraints precluded the use of large spread footings. In the 1980&apos;s the Port Authority undertook extensive testing to evaluate various piles and drilled shafts types. The LRS piling sub-contractor and the Geotechnical Engineer conducted additional tests for this project to identify the most cost effective deep foundation type. Candidate piles types included: Monotube®, Tapertube®, and closed ended pipe piles. The tapered pile types were found to be the most cost effective and the project utilized both the Monotube® and Tapertube® piles. This paper presents the results of the load test program and the issues related to pile driving induced vibrations and ground movement.

Jan 1, 2000

By Xu Youzai

Static loading teets of five nodular piles and four non-nodular piles were performed in Tianjin soft clayey soil in which measurements of axial force and movements were made. Distribution of shaft resistance and load-movment curves for pile head and pile toe are presented in this paper. The applicability of nodular piles to soft soil and their effectiveness are also discussed. Based on the comparison, it is concluded that nodular piles have an advantage over non-nodular piles mainly in contri­bution to shaft resistance. Dynamic testing was also conducted through R. P. T. for evaluating the service load of tested piles.

Jan 1, 1991

By Roy A. Bell

A 200-foot diameter, 72-foot high petroleum storage tank was built in a hillside ravine where a portion of the site contained soft clay fill. Soil-cement piles, 40 inches in diameter and up to 38 feet long, were installed to support the tank shell and ringwall, and a portion of the tank floor by drilling into the stiff to hard underlying soils and weathered bedrock. The goal was to provide a strong enough foundation to resist the seismic tank shell loading and to minimize differential settlement of the tank shell to avoid out-of-round clearance problems between the shell and floating-roof. A cantilevered retaining wall up to 8 feet high was constructed around a portion of the tank perimeter by inserting steel H-beams into soil-cement piles. The cantilever soldier piles for the retaining wall were installed from a temporary earth embankment on the hillside directly over the top of the wall. The temporary embankment was then removed and the tank pad was cut to grade in front of the soldier piles. Some of the soil-cement piles for both the tank foundation and retaining wall could not be advanced to design depth because the drill/mixing tools could not penetrate to the required depth in the hard soils/bedrock. Smaller diameter borings (22 inches in diameter) were drilled through the centers of the short-of-design soil-cement piles to the design depth and then backfilled with concrete.

Jan 1, 1997

By R. Bellotti

The theory of cavity expansion in an infinite frictional soil mass whose strength is represented by a curved Mohr-Coulomb failure envelope has been used to predict with some confidence the cone resistance of a clean dry sand. Experimental data were obtained from cone penetration and pressuremeter tests on two sands, conducted in a large calibration chamber (CC) under carefully controlled placement and boundary conditions. A plane strain bearing capacity theory was developed, and to convert the results to axi-symmetric conditions, an empirical "shape factor" was used. In the paper, the theoretical background, experimental data, calculation procedure, and the results of the analysis are presented. In general, a reasonable validation of the cavity expansion approach to the bearing capacity of deep foundations has been obtained.

Jan 1, 1987