Search Documents

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By Robert Thurner

The underground car park "Admonterhof in the historical centre of Graz is an example for the technical and economical success of a complicated structural design using a concept on the basis of the observational method. The intention to built a 20 m deep excavation beneath a protected monument was accompanied by some essential issues: the preservation of the existing state avoiding extensive displacements by means of a girder grid of reinforced concrete, its support on large bored piles and small steel-tube piles with possible active compensation of differential settlements, the excavation support in none built-up areas with secant bored piles, the underpinning of existing buildings with different structures by means of jet grouting. Furthermore the hydraulic gradient and the permeability of a rock formation in a part of the excavation had to be explored with the purpose to control the inflow of groundwater with a level difference of more than 10 m.

Jan 1, 2006

By Bengt H. Fellenius

THIS PAPER deals with the analysis of results from axial testing of vertical single piles, i.e. the most common field test per-formed. Despite the numerous tests which have been carried out and the many Papers which have reported on such tests and the analysis thereof, the understanding of pile test loading in current engineering practice leaves much to be de-sired. The reason for this is that the engineers have concerned themselves with mainly only one question: "Does the pile have a certain least capacity?", finding little of practical value in analysing the actual capacity and the pile-soil interaction. This Paper aims to show that engineering value can be gained from elaborating on a pile test ? during the actual testing in the Held, as well as in the analysis of the results. The first portion of the notes make use of an earlier Paper by the author (Fellenius. 1975). However, additional views and recent literature have been incorporated.

Jan 1, 1988

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

By Christian Besson

This article describes the implementation of a new jointing process for use between diaphragm wall panels. This process was initially introduced on the SOCATOP work site in uburban Paris (which involved the closing of the western section of the A86 bypass road), on a tunnel ventilation shaft. This brand new system upgrades the potential offered by other types of joints available and enables both ensuring the continuity of panels for structures over 40 m in depth under the strictest safety conditions and constructing shafts with diameters of less than 15 m. A patent for this process has recently been filed.

Jan 1, 2002

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

By Stephan Großwig, Karolina Nycz, Arne Kindler

"Commonly used anchor monitoring systems are mainly based on the use of anchor force meters. However, experience shows that the reliability of the display of force meters lowers over time. Other measurement and test methods like for example fibre bragg grating method require a comparison with an unloaded optical fibre and give only selective information about the bearing behavior. Moreover the obtained information has to be interpreted. In the following article, first measuring results of an anchor monitoring system based on measurements with optical fibre are presented. The new monitoring system is based on the Rayleigh technology and was used to test the load bearing behavior of the anchor grout body as well as for the evaluation of the grout body condition in concrete-damaging groundwater.INTRODUCTIONThe first fibre optic sensors came onto the market about three decades ago. Initially used as special solutions only in selected cases, now they have found use in almost all areas of technology, especially in areas, where electrical sensor systems reach their limits. The first application examples of spatially resolved fibre-optic sensors in the field of geotechnics have been in existence since the mid-1990s, in projects such as the assessment of the of radioactive repository location sites (Hurtig et al. 1994), for the monitoring of landfill sealing systems (Hurtig et al. 1995) or within the framework of the rehabilitation of mountain farming landscapes (Schreck et al. 1998).The company's first own works in the field of glass fibre measurement technology have been in existence since 1993. The first carried out projects were a monitoring at the Edertalsperre (Dietz et al. 2001), a monitoring with glass fibre tendon at a flood bridge in Carinthia as well as monitoring within the framework of the Storebælt crossing. In all cases, the structure was permanently monitored by means of individual-point measurements. Since 1993 various fibre-optic sensor solutions for geotechnical applications have been introduced to the market (Voet, Glötzl 1996, Hurtig et al. 1994)."

Jan 1, 2017

By D. Millgard

Dennis Millgard introduced the Session by hoping that participants to the Conference would also share their piling problems. He then invited the first speaker to present his paper. Paper 5.1. Pat Kelleher commenced by saying that he belonged to a one hundred year old firm that had experience in the New York Harbour area. They were often asked to assess the integrity of many waterside structures such as piers, walls, and docks which were deteriorating whilst still in use. The earliest structures, built in the 1800's, were on timber piles. These have now changed to Steel H and tube piles and concrete piles. Usually they were called in when the structure was showing signs of distress, or had reached the end of its life but could not be closed. In particular, they had found that marine borers had returned to New York Harbour because of the improved quality of the water. There is now a far greater incidence of attack on the timber piles than when the water was polluted. Repair is usually carried out by encapsulating the pile within the tidal range of about -2ft to +8ft (-0.6 to +2.4m). Reinforced concrete forms, reinforced fibre jackets, or nylon bags are used. Reinforced fibre jackets are used with a protective coat on the pile, while nylon bags prove the cheapest method.

Jan 1, 1991

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

By Masaki Kitazume

"Abstract The wet type and dry type of deep mixing methods have been developed and widely applied for on-land and marine constructions in Japan. The quality assurance (QA) of the methods has been usually carried out by unconfined compression test on field stabilized soil sampled by core boring in Japan. In some other countries, stabilized soil excavated by the wet grab sampling instead of core sampling is often subjected to unconfined compression test for quality assurance. There are several merits and demerits in each method, but few studies have been carried out to compare the stabilized soil strength of these two types of specimens to discuss their applicability to practical construction. The author has conducted a series of field and laboratory tests to compare the stabilized soil strength and discuss the applicability of wet grab sampling to QA for wet and dry types of deep mixing method.In this study, the wet grab sampling was carried out at two road embankment construction sites where the wet type and dry type of deep mixing were applied. The cement stabilized soil was excavated at the three depths by a wet grab sampler soon after the DM column construction. The test result is compared with the other test data in the previous study to discuss the applicability of the web grab sampling method for QA of cement stabilized soil.IntroductionThe Deep Mixing Method (DMM), an in-situ soil stabilization technique using cement and/or lime as a binder, is often employed to improve soft soils (Kitazume and Terashi, 2013). A variety of factors and their interactions affect the eventual strength of a deep-mixed column, while some of which are controllable (e.g. binder type and dose) by engineers while the others are not (e.g. soil types, ground temperature, etc.; Babasaki et al., 1997). In addition to laboratory mix tests, which in essence are a parametric study to estimate the influence of these factors on a particular soil’s strength, the quality assurance (QA) practice in Japan usually involves unconfined compression test on sampling cores from the stabilized columns after a given curing period. It has been recognized, however, that the ‘field strength’, or the strength of the retrieved core, quf is on average lower than the ‘laboratory strength’, qul, evaluated by laboratory mix test. Also allowing for the inevitable variability, existing guidelines (for example, PWRC, 2004 and CDIT, 2008) recommend the design quf /qul values of, for example, 0.5-1.0 for the CDM (Cement Deep Mixing; a wet-type technique, in which binder is added as slurry) and 0.2-0.33 for the DJM (Dry Jet Mixing; a dry-type technique, in which binder is added as powder)."

Jan 1, 2014

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By Philip J. Daynes

As part of the regeneration of the centre of Dublin, a multi-functional development is being constructed on the site of the historic Smithfield Fruit Market. The site is being developed in three phases, and includes one of the deepest basements (10m) constructed in Ireland to date. Until the recent improved economic climate, there has been little requirement for deep basements in Dublin, and this is the first to be constructed entirely within fluvio-glacial gravels and boulders. The difficult ground conditions led to the adoption of a diaphragm wall solution to ensure a watertight construction. Tie-back anchorages are utilised in the temporary case, and the wall is propped by floor slabs in the permanent case. Where required by high bedrock levels, the diaphragm wall is dowelled into limestone bedrock to ensure toe stability. The recorded lateral movement of the wall is significantly below that calculated by numerical analysis. Temporary bentonite cut-off walls were installed to divide the site into discrete sections. The basement was constructed as a tanked structure, and is subject to uplift water pressure. Passive tension minipiles provides an innovative alternative to the standard stressed anchorage solution. This paper describes:- design and construction aspects of the diaphragm wall, tie-back anchorages, and anti-flotation minipiles, together with recorded lateral wall movements,

Jan 1, 2003

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

By K. Kawakami

In Japan, pile foundations have been used extensively for buildings, bridges and port facilities. A large number of steel pipe piles were first used in the 1960's and the amount of steel used in foundations increased by 1973 to one million tons. This report describes current practice in the actual use of large diameter and long steel pipe piles in Japan, related to their performance: including consideration of pile size, hammer types used for driving the results of field tests measuring stress occurring in the piles and the driving formulae currently being used in practice in Japan.

Jan 1, 2010

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By Matthias Pulsfort, Markus Herten, Rolf Breitenbücher, Claudia Fierenkothen

"Secant bored pile walls are frequently used as retaining walls in watertight excavations to cut off ground water aquifers and are subsequently exposed to ground water pressure loading in addition to earth pressure loads. To avoid extra loading from ground water pressure in soils with limited permeability, it can be useful to arrange drainage windows within secant bored pile walls by means of single primary piles filled with porous concrete without reinforcement cages, which usually have to be placed within casings in submerged conditions. This concrete may serve as a horizontal arch between the reinforced secondary piles, but it must however enable vertical draining between load carrying construction beams and the bottom of the excavated pit. In the present submission, the results of several material tests with different mix designs of porous concrete with certain admixtures are presented together with first and important experiences with a wellsuited placement technique for porous concrete casings in small- and large-scale laboratory tests. It can be shown that the usual placement technique of employing a tremie pipe is not suited for this type of unsaturated concrete. Instead, pouring with a particular kind of cone and an open conductor pipe has proven successful.Additionally, special testing methods are currently developed for judging the suitability of the desired concrete mix design in preparation for an upcoming real-scale experimental pile installation in Germany.1. INTRODUCTIONRetaining walls are often built as secant bored pile walls in order to cut off aquifers saturated with groundwater against deep building pits. In soil types with relatively low permeability, however, seepage flow may be permitted, because the quantity of groundwater to be pumped is limited, and the range of influence due to dewatering is not reaching far. Thus, the hydrostatic water pressure on the retaining wall can be considerably reduced, leading to a more economic design (see Fig. 1).In unsaturated soils, the dewatering effect can be achieved by means of porous pervious concrete with a uniform grainsize distribution of aggregates typically placed in a borehole under dry conditions. With regard to the use of porous concrete to be placed at the ground surface in road pavement applications, experience is sufficiently available as shown, for instance, by Neithalath et el. (2010). However placing the porous concrete in a bored pile using a tremie pipe under submerged conditions is a challenge and a completely new approach, because there is a considerable risk of segregation of the fresh concrete, separating the cement lime paste from the aggregates when in contact with water and leaving only neat gravel on the one hand as well as a tight cemented area at the bottom of the pile on the other hand. If this concrete placement is successful, additional dewatering by means of extra wells behind the retaining wall can be avoided. Of course the seepage flow in the adjacent soil needs to be regarded seriously."

Jan 1, 2017

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000