Search Documents

By Gregg S. Hill, Bert J. Huls

"This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed us to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flow sheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit. Details of the technology behind each unit operation will be presented in later publications.INTRODUCTIONSince 1996 BHPBilliton and MEL (Minera Escondida Ltda.) have developed a process to recover copper from coarse particles in the rougher tailings. Copper recovery from fresh tailings is not new. Several operations in Chile, such as Chuquicamata, El Teniente (AMEC, 2003), Mantos Blancos and others have operated various forms of tailings circuits. Both Chuquicamata and El Teniente practice cascade flotation scalping off froth containing fine copper particles after allowing sufficient retention time, air inducement and, sometimes, additional reagent addition. Chuquicamata tailings are not segregated but floated in sequential cascade and conventional large cell arrangements. At the Valle Central operation of El Teniente a coarse fraction of mill tailings is ground and floated, with the rejects recombined with fine tailings and subjected to cascade flotation through a sequence of concrete launders as the tailings flow towards their final deposition area. Mantos Blancos cyclone the rougher tailings and blend the underflow with scavenger concentrate from elsewhere in the principal circuit prior to flotation in Wemco Cells. Kemess in BC, Canada operates a 160 m3 Outokumpu cell to reduce the tailings sulfur content (Rasmussen, et.al, 2004)."

Jan 1, 2005

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By Dave Price

"Canada is scheduled to become the 4th highest diamond revenue producing country in the world by year 2004 with the already operating Ekati Mine and the anticipated operation of the Jericho Mine in 2002 and the Diavik Mine in 2003.This paper provides an overview of worldwide diamond production statistics and a brief introduction to a diamond processing plant. The dense medium separation (DMS) extraction process is presented and this process is discussed in more detail with respect to the extraction of diamonds in terms of feed preparation, dense medium, dense medium cyclones, ferrosilicon recovery and dense medium cyclone operating efficiencies.INTRODUCTIONThe Ekati Diamond Mine in the Northwest Territories started commercial production of diamonds in the 4* quarter of 1998. At full production, the mine is anticipated to produce annually some 3 million carats of diamonds. The Jericho Mine in Nunavut Territory and the Diavik Mine in the Northwest Territories are anticipated to come into production in the 1'' quarter of 2002 and 1st half of 2003 respectively. The combined annual diamond production of these three mines will total approximately 10.34 million carats by 2004, making Canada the 4~ highest diamond revenue producing country in the world.A diamond processing plant initially utilizes crushing, scrubbing and screening in the beneficiation process to liberate diamonds from kimberlite ore and size the product for further treatment through DMS. Alluvial diamond operations do not require initial crushing and scrubbing but incorporate a feed preparation and sometimes a recrush facility with the DMS plant. The heavy sink product from the DMS, which contains diamonds, is further upgraded through x-ray separation and high intensity magnetic separation prior to producing the final diamond product.DMS is a relatively simple separating principle. A mixture of particles of different density is immersed in a dense fluid, so that particles having a density lower than that of the fluid will float while those of heavier density will sink. The translation of the float-sink principle from a laboratory method to continuous industrial practice offers the prospect of very precise mineral separations based on density differences alone."

Jan 1, 2000

By A. Demirci, A. Keçeciler, Y. S. Durutürk

"This paper deals with the results of the variation of thermal conductivity of rocks with pressure on a laboratory scale. For this purpose, the authors have added a pressure-supplying unit to the apparatus developed by Mousset-Jones and McPherson (1986), Önder (1995), Ashworth and Ashworth (1979), and Innaurato and Occella (1989) in order to measure the thermal conductivity under pressure. The values obtained from the tests performed by this new apparatus have been stated using a regression analysis and the related graphs have been drawn. Results have shown that the thermal conductivity of rock varies digressively with pressure. The same results have been obtained in different rocks types. IntroductionOne of the most important tasks of mining engineers is that of establishing, maintaining and sustaining safe and healthy working conditions in underground mines.Heat can have a profound effect on safe and healthy working conditions and is one of the main problems in deep underground mines. In this regard, the temperature of the air passing through the mine openings increases steadily and causes a decrease in the efficiency of workers due to the unwanted physical effects to human bodies in the working area. At the same time, the hot and humid environment resulting from heat and temperature rise causes some important occupational diseases and increases the accident risks in the related openings."

Jan 1, 2002

By P. Taskinen, D. Lindberg, H. Viitala

The formation of copper chlorides in flue dust or deposits in heat recovery boiler of copper smelters or waste-fired boilers may lead to formation of corrosive partially molten deposits on walls and heat exchangers of the boilers. These deposits can contain various other metals, such as alkalis, Fe, Zn, Pb together with oxides and sulfates. In the present study, a thermodynamic model for copper-containing binary and ternary metal chloride systems within multicomponent CuCl-CuCl2-FeCl2-FeCl3- PbCl2-ZnCl2 system has been assessed and optimized based on own experimental phase equilibrium data, as well as literature data. The thermodynamic properties of the liquid phase was modelled using the quasichemical quadruplet model and a thermodynamic database was optimized to predict all available experimental data within the experimental error limits. The thermodynamic database allows for more accurate predictions of potential corrosion-related issues in various heat recovery boilers and waste-fired boilers due to formation of copper chlorides. INTRODUCTION In the copper flash smelting, flue dust can cause severe problems in the gas train, used for separating dust from the SO2-rich off gas, by forming corroding accretions on the walls of the heat recovery boiler. Formation of dust build-ups in the boiler need to be cleaned regularly and potential corrosion damage checked, requiring costly and unscheduled shutdowns of the flash smelting process. Compounds of copper and zinc among other elements having high vapour pressures may volatilize during the smelting of the copper concentrate, forming dust when the process gas cools down. Also, particles of solid or liquid iron oxides originating from the ore get transported with process gas to the heat recovery boiler as a result of entrainment in the flue gas (Miettinen, 2008) The dust deposit build-ups on the boiler walls are formed partly by direct impact of particles and partly by vapour condensation on the boiler walls. The initial deposition takes place by the condensation of vapours that contain zinc, lead, arsenic and other metals having high vapour pressures. Also, low melting point eutectic components of alkali salts such as chlorides and sulphates can act as sticky cohesive particles attaching to the boiler walls. The fine particles landing on the surface of the porous dust deposit layer react in the SO2-rich atmosphere of the boiler to sulphates. The process gas within the boiler contains SO2, O2, SO3, H2O and N2 that diffuse into the porous accretions to form a stagnant gas layer within the dust deposit structure. The composition of this gas layer may differ greatly from the composition of the process gas that is flowing on the surface of the accretion layer. Locally HCl and H2SO4 are formed and even a reducing atmosphere may exist within the dust deposit layer, allowing new reactions to take place. The local micro-atmosphere may enable metal sulphates to be reduced to secondary sulphides and even metallic components. Within the accretion layer, components may be formed that would not be stable in the gas atmosphere inside the boiler (Miettinen, 2008). This may be the mechanism by which for instance chlorides of Cu, Fe and Zn are formed within the deposit layer.

Jan 1, 2019

The importance of understanding the behaviour of cemented paste backfill (CPB) within the framework of the effective stress concept is highlighted in this paper. Only through an understanding built on this concept can problems such as barricade loads, the rate of consolidation and arching, be fully understood. The critical importance of the development of stiffness during the hydration process, and its impact on factors such as barricade loads, is used to illustrate why conventional approaches that implicitly ignore the effective stress principle are incapable of capturing the essential components of CPB behaviour.

May 1, 2007

By Peter Dunn

London Mining Plc. is developing an iron ore project in Sierra Leone. The Marampa mine is a brownfield development effort, having been operated by others since the 1930?s until low iron ore prices forced closure. Peak production of the prior operations was approximately 2.5 Mt/a in the 1960?s. Following civil war In Sierra Leone, London Mining obtained the mining license in 2006 and commenced activity to redevelop the Marampa mining and processing operations. There are two ore deposits of interest for development as well as a resource comprised of tailings from previous operations. Phase 1 will be the mining of the tailings resource with a 1.8 Mt/a plant producing 66 per cent Fe sinter feed, expandable to 3.6 Mtpa. The first phase is currently under construction with start-up expected in the third quarter of 2011. Phase 2 will include development of the two ore deposits. These deposits are weathered secondary ore and the main primary ore resource. Phase 2 is currently under prefeasibility study and targets a final 16 Mt/a concentrate production in 2016. Outotec partnered with London Mining on testing efforts to develop the magnetic separation flowsheet using SLon VPHGMS machines to process the Marampa material. This paper explains the flowsheet development process for the weathered and primary ores commencing with sample characterization and detailed parametric investigations to evaluate SLon performance. The final flowsheet configuration is explained, including expected circuit recoveries and concentrate quality, clearly demonstrating the performance of the SLon VPHGMS circuit in iron ore tailings treatment applications.

May 1, 2011

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

By T. B. Armstrong

"The developing world energy crisis and spiraling fuel costs have created a new public awareness and general acceptance of the need for energy conservation.Plants will have different objectives for an energy conservation program but there appears to be a common approach on how to save electrical energy.Data for a 180tph Rod Mill powered by a 750 hp motor will be used to demonstrate the relationship of energy input and production levels and to seek an optimum operating condition.Energy Conservation:Plants that have examined ways of dealing with the energy situations have concluded that energy conservation has important benefits for industry, including reduced costs, fewer production slowdowns inthe event of fuel shortages and a continued competitive position.There have been some ""startling"" conservation achievements attained through such simple plant maintenance and operating practices as reducing unnecessary lighting in buildings and yards, turning off' equipment not needed at night or over week-ends, through planning maintenance and production schedules to minimize energy use and through improving quality control to eliminate waste.Significant reducti.ons in energy use have been achieved by some rather simple but vigorous maintenance and plant engineering efforts directed at finding and fixing energy ""leaks"" rather than technological advances or major rework or redesign of facilities and equipment.An Energy Conservation Program often must overcome such obstacles as historic operating practices and emp1-oyee indifference, i.e. the ris.ing costs of fuel should result in re-examination of so1ne basic attitudes to energy conservation. Some measures, rejected in the past largely on the grounds of capj.tal. expenditure, now make economic sense in the light of future escalating energy costs."

Jan 1, 1978

By G. Halverson, K. Blower

"Giant Yellowknife Mines Limited (Giant) has been producing gold since 1948. Located at Yellowknife, Northwest Territories, Canada, see Figure 1, the mine processes approximately 1,200 short tons per day of 0.23 ounce gold per ton of ore.The majority of the gold in the ore is sub-microscopic and associated within the mineral arsenopyrite. This association complicates the extraction method since straight cyanidation will only recover 30% of the gold. The operations at Giant involve four essential steps, with an overall recovery of 87%. The steps shown in Figure 2 are crushing and grinding, flotation, roasting and cyanidation. These processes result in a number of effluent waste streams characterized in Table 1. These streams are combined and sent to a tailings storage pond for subsequent treatment prior to discharge to the environment.Giant is located just north of the 62nd parallel where winter temperatures drop to -40°C for extended periods. This entails storing effluent in dams over the seven month winter period for treatment during the relatively short summer season.The treatment method currently employed at Giant is an ""alkaline chlorination-arsenic precipitation-flocculation"" process. The pond water is subjected to three phases of treatment prior to being discharged to the environment as shown in Figure 3."

Jan 1, 1987

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 45 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonnes of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in the US and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Nov 1, 2011

By R. D. Brown

"AbstractIn order to raise the enormous amounts of capital which will be essential for the development of Canada's mineral and petroleum resources, this country's resource industry must be permitted to earn an acceptable rate of return. The existing tax regime, with its high rates, complexities and misdirected incentives, presents a serious obstacle to our resource industries in their development of Canada's immense , but increasingly lean, resources. Government tax and other policies are not the only cause of the crisis now facing the resource sector in Canada, but a reformed tax system, with stable and reasonable tax burdens, is required if Canada's resources of minerals, oil and natural gas are to continue to contribute in the future, as in the past, to our national well-being.An independent task force, organized under the auspices of the Canada West Foundation, has recently completed a wide -ranging report: on the future development of Canada's mineral, oil and gas resources. This five-volume report, completed after almost two years of research and study, concludes that Canada •is facing a major crisis •in the development of our resources, It states that unless corrective action is taken now, mineral production and exports could decline drastically after 1985, at the same time that Canada would face massive bills for imported oil because of inadequate and declining production.The task force, chaired by the author of this article, has put forward recommendations for a fundamental shift in both federal and provincial policies in order that Canada's mineral reserves can be developed in the national interest. This article consists of excerpts from the summary of the task force's report."

Jan 1, 1977

By S. Klingmann, G. Blackwell

"Terrestrial photogrammetry has been used for many years to build three-dimensional pictures for analytical purposes. Photographs can include images from open pit mine walls, ground topography, mine buildings infrastructure or accident scenes. Analysis and co-ordinate estimation in early photogrammetric systems demanded the use of specialized and costly optical-mechanical stereocomparators. Few of these instruments could be interfaced with computers to provide databases, and all required trained personnel with good perspective vision to collect data.Digital photogrammetric software has replaced these older systems, and the digital video plotter (DVP) is a simple computerized system utilizing readily available PCs to quickly produce a stereoscopic model of any scene where an area of overlap exists in photographs taken from two different locations. Specialized cameras providing reference marks or grids on the photographs are still necessary for detailed analysis in three dimensions.This paper describes the application of DVP to the three-dimensional analysis of strike, dip and location of dominant fracture planes visible on an open pit wall slope, and the intersection of planar features which might reduce wall stability. Where reference survey points cannot be provided because access by personnel to the photographic scene is impossible for safety reasons, normal case terrestrial photogrammetry can provide the necessary control points for more complex aerial photogrammetry geometries.DVP recreates the geometry existing at the moment photographs are taken, providing the user with the ability to safely recreate, compare and analyze the structures determining the stability of open pit wall slopes."

Jan 1, 2003

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By Y. Faitakis

In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production. It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About one-third of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations: The first generation (1940?1950): A ?fix it when it broke? attitude prevailed during that time, mostly because the industry was not highly automated. The second generation (1950?1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly. The third generation (1980?): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex, multi-functional teams become responsible for maintenance. At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance.

Jan 1, 2004

By Y. Faitakis, G. J. Powley, C. Mackenzie

"In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production.It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About onethird of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations:The first generation (1940–1950): A “fix it when it broke” attitude prevailed during that time, mostly because the industry was not highly automated.The second generation (1950–1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly.The third generation (1980–): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex multi-functional teams become responsible for maintenance.At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance."

Jan 1, 2004

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

The world’s first copper electrorefinery started production in 1869 at Burry Port in South Wales. Built within the Pembrey Copper Works which had commenced smelting operations in 1849, the new refinery was based on principles described in the British patents issued to J.B. Elkington in 1865 and 1869. Refining principles and practices pioneered there were key to the foundation of modern electro-refining practice in what is now a dominant international industry producing over 16 Mt of electrical grade copper annually. This paper explores the background to this pioneering application of the new, early 19th century, science of “electro-metallurgy” and examines its links to the contemporary decorative electro-plating industry and to the shortcomings of 19th century fire refining. The beginnings and early years of the Pembrey electrorefinery are briefly discussed in relation to the quality, applications and pyrometallurgy of copper at the time. More than a decade would elapse before the birth of the electrical age: the Pembrey refinery may be seen as one of its vital precursors. Note: This paper was originally published as part of the Copper 2013 proceedings (A.E. Wraith, P.J. Mackey and J. (formerly R.) Protheroe Jones, “Origins of Electrorefining: Birth of the Technology and the World’s First Commercial Electro-Refinery”, paper in Electrorefining, Vol. V, Book 2, (Eds. R. Abel and C. Delgado), Cu 2013 International Conference, pp. 19-33, IIMCh, Santiago, Chile, 2013). It is reproduced here together with a new Appendix and supporting references that lists the year of commencement of the first electrolytic copper refinery by country, 1869 to 1956. It all, the year of the first electrolytic copper refinery established for 15 countries is included. These 15 countries now produce more that 70% of world refined copper (for 2018). INTRODUCTION In the 1840s, the new science of ‘electro-metallurgy’, a term coined by Smee in 1841 (Smee, 1841), was being adapted to the decorative electro-deposition of silver in a thin, bright adherent coating that was evidently equal in appearance to traditional silverware (Williams, 1976). Chief among innovative manufacturers of decorative objects who took up the new art of silver electro-plating was the acclaimed firm of G.R. Elkington and Co. of Birmingham, England. The company, which vigorously developed all aspects of electro-metallurgy for the decorative trade, entered the field of ‘electrotyping’, a technique in which the surface features of a mould are copied on an electro-deposited copper layer which, when stripped off, can be used to reproduce an imprint of the mould. In essence, it is a form of casting by electrodeposition, invented in 1837 independently by Jacobi in Russia (Pavlova, 1968) and Spencer in England (Wyatt, 1851).

Jan 1, 2019

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack &apos;of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930