Search Documents

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By J. E. Gill, A. R. Byers

The Surf and Pugsley gold-copper mines; owned and operated by Surf Inlet Consolidated Gold Mines; Limited; are about 6 miles inland from; the head of Surf inlet; on Princess Royal island; Skeena mining division; British Columbia. Surf inlet is a fiord 360 miles in an air line northwest of; Vancouver.

Jan 1, 1954

By D. P. Wilkinson

Flow field design is critical to determining fuel cell performance with respect to operating conditions. Flow fields are normally designed around their maximum power operating point with the goals of maximizing performance and minimizing pressure drop between the inlet and outlet of the flow field. At lower power pressure drop is reduced, and water management and reactant distribution issues can occur over the active area as well as issues with cell to cell reactant distribution in the fuel cell stack. Flow fields have fixed flow channel geometries and fixed active areas which determine the reactant flow characteristics over the operational range of the fuel cell. In this paper we discuss some of the benefits of a new approach of changing the flow field active area with changing operating conditions. Such benefits for future fuel cell designs could include improved cell performance and stability, improved cell to cell reactant distribution, reduced low current density failure modes, and overall system advantages.

Jan 1, 2005

Spatial information Critical to a project since it underpins: ?Discovery of mineral resources ?Orebodydefinition and technical assessment ?Mine design and planning ?Profitability and project value Data ?Single most import asset. ?Good interpretation of quality data underpins project growth and success. TEAMWORK

May 1, 2002

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

By H. Staton, V. Suontaka, E. Sharifi

"Flotation circuits are typically controlled using on-line elemental assays obtained from the slurry lines. In base metal applications, X-ray fluorescence (XRF) analyzers are the most common instruments for elemental analysis of the slurries. Eagle Mine has been utilizing a Courier XRF Analyzer since 2014. Typically, in XRF analysis, the sampling rate is 10-25 minutes which is good enough for manual process control. In 2018, Eagle Mine upgraded the Courier XRF analyzer with the Rapid Measurement module that is based on reflectance spectroscopy. This option reduces the sampling rate to 10-15 seconds, while maintaining the superior accuracy of the XRF analyzer. This paper presents the results from implementation of Rapid Measurement at Eagle Mine.INTRODUCTION Eagle mine is an underground mine producing nickel and copper concentrates. Eagle Mine is owned by Lundin mining and located in the Upper Peninsula of Michigan, USA. The Humboldt Mill, previously an iron ore processing facility, was refurbished in 2014 and is used to process the ore and produce separate nickel and copper concentrates. Approximately 2,000 metric tonnes of ore is milled per day. Ore is processed using a conventional crushing followed by single stage ball mill and flotation. Nickel and copper concentrate are transported to facilities in North America via rail car. A bulk copper-nickel concentrate is produced by separating the copper and nickel minerals from gangue material by flotation. The copper-nickel bulk concentrate is reground, followed by one stage of cleaning to reject further gangue minerals. The bulk cleaner concentrate is then subjected to a final flotation stage where the copper and nickel minerals are separated from one another through the addition of lime. Final concentrate grades are 14% Ni and 2% Cu in the nickel concentrate and 31% Cu and 0.8% Ni in copper concentrate."

Jan 1, 2019

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By H. Fujihara, K. Uesugi, H. Toda, A. Takeuchi, K. Shimizu

"Hydrogen is trapped at a variety of microstructures, for example grain boundaries, dislocations and particles. It is thought that hydrogen trapped at trapping sites is redistributed to the other sites under loading and then brittle fracture occurs with hydrogen accumulation. In order to understand hydrogen embrittlement behavior, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, changes in hydrogen distribution are observed under stress using Kelvin force microscopy (KFM) that can visualize hydrogen concentration distribution on material surface at high resolution. Spot-like hydrogen enriched regions are observed on the surface of a material. In addition, hydrogen depleted regions are observed around those enriched regions, and the appearance of hydrogen trap due to particles existing near the material surface is revealed. On the other hand, hydrogen trapped at grain boundary can be visualized. From in this result, it was suggested that crystallographic factors influence hydrogen accumulation. The relationship between initiation and propagation of intergranular crack and hydrogen accumulation under stress will be discussed.INTRODUCTIONHydrogen present in a metal sometimes has significant effects on various properties. Hydrogen in a metal is trapped at a variety of microstructure, for example dislocations and grain boundaries. Grain boundaries, dislocations and micro pores are the major trap sites in aluminum alloys. Some researchers considered that hydrogen redistribution and accumulation between these trap sites in a material with loading plays an important role in the brittle fracture behavior. In general, in intergranular fracture and quasi-cleavage fracture, the hydrogen trapped at grain boundaries and dislocations contributes to fracture behavior, respectively. Recently some researchers have shown that the ductile fracture in aluminum alloys is resulted from growth and coalescence of hydrogen micro pores. Analysis using first principles calculation indicates that intergranular fracture occurs when hydrogen concentration reaches 20 atom H/nm2ongrain boundary. From this report, it is considered that hydrogen redistributed during deformation accumulates locally in order to cause hydrogen brittle fracture. In order to understand hydrogen embrittlement, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, we evaluate the relationship between hydrogen accumulation behavior and fracture behavior in Al-Zn-Mg based alloys. In-situ observation was made by combining the tensile test with Kelvin force microscope (KFM) that can visualize the hydrogen concentration distribution on the material surface with high resolution. We also investigate the relationship between hydrogen distribution behavior and crystal orientation."

Jan 1, 2018

By John Loop, W. A. Gibbins, Donald D. Hogarth

"Introduction Background The Frobisher voyages of 1577 and 1578 were organized by the Cathay Company for the express purpose of finding and mining gold ore. Since publication of the Baffm expedition of Charles Francis Hallill, the location of Kodlunarn or Countess of Warwick Island, the headquarters of Frobisher's third (1578) voyage, and focal point of the largest Arctic voyage of all time, has been known to the world. Through Hall we also know the location of the Countess of Warwick Mine on Kodlunarn Island. However, the exact locations of the other mines are not known. Of the ""ore"" we know little. Pieces of the original ""black stone"", once as large as ""a half-penny loaf' have now disappeared altogether. Specimens collected at random from the repository of shipments in England and from loose rock on Kodlunarn Island were termed, respectively, ""hornblende pyroxenite"" and ""amphibolite"" and from a locale about 200 yards from Kodlunarn as (hornblende) ""pyroxenite""121. However, it is uncertain whether these specimens are representative of Kodlunarn or of the other mines, although Blackadar131 notes that, in the northern trench of Kodlunarn, biotite gneiss contains lenses and bands of amphibolite. The ""gold"" itself is even less well defined. It has long been accepted that gold was virtually absent in Frobisher's ore. The ""gold"" has been termed pyrite, biotite and both biotite and pyrite together. Even t h e word "" marquesset"" , which appears and reappears in contemporary descriptions, is nebulous and is defined as ""a stone participating in the nature of some metal, yet in so small quantity, that the metal cannot be melted from it"" (0.E.D., definition of 1616)."

Jan 1, 1999

By Edmond Chow

Shovel bucket blast fragmentation analysis is an alternate way to assess blast performance and its effects on downstream mining processes. A camera is installed on the boom of cable shovels, and the stick of hydraulic shovels. Images are captured automatically as the shovel digs, and are processed to acquire rock size information. The automatic data acquisition makes this method safe to use with minimal manual labour. It also allows for a large set of sample data to be captured from both the surface and the interior of a bench face. The system has been deployed in several mines to provide an objective assessment of blasting performance. Images are captured from their cable or hydraulic shovels. The images are grouped into sets based on the shovel location and time to match the fragmentation to specific blasts. Blast fragmentation reports are created for each blast after reviewing the results. Measuring blast fragmentation from the shovel bucket proves to be an effective alternative for blast performance assessment with unique advantages. The blast fragmentation information has been valuable to the mines, and the mines have begun adopting it into their operations.

May 1, 2011

By Bonnie Cooper

3D printing by fused deposition can be used on lunar soil. The soil can be precisely size-separated to make the 3D printing process work efficiently. Using a MASER instead of a LASER would allow us to use the finest fraction of lunar soil, AS-IS, to manufacture things on the Moon.

May 1, 2013

By D. G. Cerigo

"INTRODUCTIONAn interim report covering an uncompleted project on revenue mill optimization was presented at the invitation of Mr. C.S. Stevens, the Secretary of the Canadian Gold Metallurgists. The work described summarizes the preliminary work carried out at the Noranda Research Centre on computer mill optimization and is an attempt to arrive at a model of a circuit using the ""black box"" approach and hence by using economic factors related to concentrate dollar value to maximize revenue. The help and cooperation of Mr. J.D. Wild, Mr. M.J.S. Bennett of Noranda and Dr. A. Bobkowicz of McGill University is gratefully acknowledged.DERIVATION OF MODELHistorical data from the Normetal mill were used for the study. Normetal ore contains chalcopyrite, sphalerite, gold, silver, pyrite and pyrrhotite. For simplicity, data were chosen for days when only two concentrates had been derived, a copper concentrate which also contains the gold and silver, and a zinc concentrate. In these periods when pyrite concentrate was not produced, its circuit was used as an extra zinc scavenger unit. Figure I is a schematic drawing of the circuit and Table I explains the nomenclature.The mill had been operated to obtain a fixed grade of copper and zinc in the copper and zinc concentrates respectively, at the same time insuring acceptable recovery levels. The target grade for the copper and zinc concentrates had been derived by manual calculations based on past experience. The data used were 170 sets of daily mill reports, a sample of which is shown in Table II. The data consist of daily tonnages of feed, concentrates and tailings and their average compositions obtained by taking samples every twenty minutes from each stream and analyzing the daily composite samples."

Jan 1, 1967

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By G. J. Kipouros, N. Dadvand

"In recent years coatings of alloys have been produced for a wide range of applications including many for wire bonding application. The main characteristic of the baths of electroless plating is the presence of sodium hypophosphite as a reducing agent and also as the supplier of phosphorus. In the electroplating of alloys the Watts bath is predominantly used. This presentation compares the two techniques, electroless plating and electroplating, and discusses the possibilities of cross utilization of sodium hypophosphite in an attempt to formulate baths that eliminate the waste disposal issue related to some components.INTRODUCTIONThe importance of surface characteristics and the linkage of surface coating process to surface characterization has given rise to the evolution of surface engineering. Not only the surface preparation and morphology has become very important to the coating technology but also the knowledge of surface area exposed to the process of coating or corrosion is absolutely essential in ascertaining the behaviour of coatings and their adherence to the substrate. The above concepts are not unknown to researchers involved in the protection of surfaces, particularly metallic, from corrosion and/or erosion corrosion. However, the complexity of the surface defects, roughness, porosity, interconnected porosity and other related factors have contributed to the uncertainty of the true surface area versus the nominal surface area. Therefore critical parameters such as current density and chemical surface intensity although have been studied extensively at the atomistic level by carefully prepared surfaces are very difficult to be determined at the practical scale required during the coating processes.The most pronounced case calling for an understanding the relationship between the surface area and the effective protection is the coating of surfaces of items produced by compression or consolidation of powdery materials. With the advent of nanomaterials and the additive manufacturing through 3D metal printing this issue is becoming more important. Certain experience in this field come from the accumulated knowledge resulted from the attempts to characterize the electrochemical behaviour of powder metallurgy metals and alloys. Powder metallurgy has been a well-established process for half a century on basic metals such as iron, copper and their alloys. Recently the development of powder metallurgy process for aluminum, titanium and attempts to develop powder metallurgy processes for magnesium and its alloys has brought to light another important issue that of the development of coatings on difficult to plate reactive metals such as aluminum and magnesium. Despite of many successes in the development of powder metallurgy alloys the exact characterization of the corrosion behaviour of the coatings and the substrates is difficult to determine because of the unknown morphology of the exposed area i.e. the exact morphology and area of the exposed surface (Samal, 2007)."

Jan 1, 2016

By B. Burger, T. Bester, S. Deonarain, L. S. Schultz

"This paper details the process followed to raise drill and equip a 6.1 metre diameter vertical service shaft at Glencore’s Mindola Deeps project in Kitwe, Copperbelt Province, Zambia. The project scope comprises a shaft collar, bulk air intake, a pre-sink to -90 metres and raise drilling the shaft from surface to a final depth of 1,892 metres underground, in four separate lifts of approximately 475 metres each. Equipping of the shaft steelwork, headframe erection and commissioning the shaft for hoisting. In addition, the scope included the development of a decline down from 5430’ level underground to the new shaft position on 6205’ level. This paper will provide some insight into the successes and challenges encountered during execution of the shaft works to date and provide some learnings for future projects of a similar nature. INTRODUCTION The Mindola Mine is situated to the west of the city of Kitwe in the Copperbelt Province of the Republic of Zambia (Figure 1). The mine is owned and operated by Mopani Copper Mines Plc (MCM), whose shareholders are Glencore AG (73.1%), First Quantum (17.9%) and ZCCM Holdings Plc (10%).Productivity at the Mindola mine has been adversely affected because of significant ventilation and ore re-handling challenges, which are caused by the dilapidated infrastructure, and design of the existing vertical and sub vertical shaft system. In the circumstances, it was apparent that it was necessary to sink a new vertical shaft that would increase the volume of fresh air down the mine, improving the underground working environment and the current hoisting restrictions, resulting in an increase in productivity and efficiency. Because there were two existing levels ideally situated and perpendicular to one another and because a third level was in close proximity to that perpendicular and because the mine required a ramp down to shaft bottom in any event, consideration was given to raise drilling the shaft as opposed to using conventional blind sinking methodologies."

Jan 1, 2019

By S. Huang, K. Xia

"During crushing, rock particle is subjected to complicated loading and the particle shape influences the fragmentation outcome. Thus, a highly controlled laboratory test is desired to establish the relation between the loading and the fragmentation parameters for better understanding the rock crushing mechanism. In this work, a split Hopkinson pressure bar system in combination with high speed cameras is utilized to carry out a dynamic ball compression test, in which the spherical rock sample is adopted to avoid the shape effect. Using the elasticity theory, the history of the axial symmetric tensile stress perpendicular to the diametrical direction along the loading axis is determined, from which the loading rate and the dynamic indirect tensile strength are calculated. With the aid of the moment-trap technique, the total energy absorbed by samples is accurately determined from the one-dimensional wave analysis. Furthermore by considering the kinetic energy of the sample fragments using the high speed camera snapshots, the surface energy is determined for each sample. The relations between the loading rate and the fragmentation parameters, i.e., the number of fragments and the surface energy are established. The application of this method to a granitic rock shows that it is flexible and can be applied to the crushing study of generic brittle solids. INTRODUCTIONCrushers are widely used to break rocks to extract specific minerals in the mining industry, and to obtain rock fragments with desired size distribution in construction industry. During crushing, the breakage of particles can be in either the single-layer mode or the multi-layer mode. In the single-layer mode, the particle breakage can be assumed to be isolated, in which the interaction between particles can be ignored. It is thus suggested by many researchers that highly controlled single particle test should be performed to establish the relation between the input mechanical energy and size reduction for better understanding the crushing mechanism (Yashima et al., 1987; Tavares, 2007; Pitchumani et al., 2004)."

Jan 1, 2015

By J. H. . MORGAN

Talc-soapstone deposits exist in Patton Township of Quebec and have been mined by Bakertalc Inc. or its predecessors since 1938. The company produces products ranging from purified and micronized talc through to soapstone lumps. The deposits are found within serpentinite dykes and are zoned. Zoning grades from a serpentine core through zones of talcmagnesite, schistose talc and talc-chlorite schist be/ ore reaching the wall rock of quartz-sericite-chlorite schist. Talcmagnesite zones generally comprise 80 to 90% of the mined rock. The serpentinite dykes containing the talc probably were originally post-Ordovician peridotite of the same series that hosts the Eastern Townships asbestos deposits. Alteration of serpentine to talc-soapstone and magnesite apparently resulted through addition of silica and carbon dioxide along shears and fractures. Talc concentrations occur also at the intrusive contact between dykes and wall rock. The present Bakertalc Inc. operation at the Van Reel Mine is being worked from an inclined shaft 200 m below surface. The talc rock undergoes a variety of milling processes, depending on its particular market, be/ ore being bagged and shipped.

Jan 1, 1984

By A. C. Ter-Oganesyants, N. N. Anisimova, G. P. Kotukhova, G. N. Dylko

The process utilized at Norilsk Nickel Polar Circle Division for treating slimes from the electrorefining of copper and nickel was developed in the late nineteen fifties and has survived without any fundamental changes. This technology is a combination of pyro and hydrometallurgical operations to produce PGM concentrates that are sent away for refining. The characteristic feature of the current technology is multiple-stage, extended cycle treatment with significant incomplete production, low labour and automation efficiency and poor hygiene and sanitary conditions. To eliminate all negative aspects mentioned above, specialists of Norilsk Nickel Polar Circle Division have developed a new hydrometallurgical process for treating electrolytic slimes. The main steps of the flow sheet developed are autoclave leaching of the slimes and electrochemical opening-up of a cake from autoclave leaching. The implementation of the new process will allow Norilsk Nickel Polar Circle Division to shorten the process cycle 4-5-fold thus reducing the volume of incomplete production, considerably increase labour efficiency, simultaneously improving working conditions, upgrade the final concentrate, reducing costs and increasing PGM recovery during refining and, ensure higher security of precious metals by employing automated processes and vacuum sealed units.

Jan 1, 2004

By S. J. Schofield

INTRODUCTION ONE of the greatest and most interesting problems of economic geology is to discover criteria bearing on the persistence of ore in depth. It is a question which is very much to the fore in connection with many of our important mines in British Columbia, and, as is to be expected, it is a most controversial one. The present paper, summarizing the views of the writers concerning the possibilities, in some of the mining districts of the Province, for the persistence of commercial ore to greater depths than have been, or are at present, mined, is offered as a basis for a general discussion on the subject and to call attention to the need for renewed study and research on the problem. Sooner or later-at some depth or other-individual ore-shoots become impoverished and bottom. In many mines where this has happened, either at the same or at a lower horizon, another ore-shoot, which had no surface outcrop, has been encountered and has continued downward until it, in turn, has pinched out. The Kolar (Mysore, India) gold field, for instance, presents interesting examples of this recurrence of ore-shoots at depth (1). For many years these mines have been under the management of Messrs. John Taylor and Sons. On more than one occasion they have persisted in sinking or drifting on barren quartz or along a narrow fracture for many hundreds of feet before values were again encountered. Their earliest experiment in such bold development took place at a depth comparable to that at which most mines in British Columbia are considered to be bottomed. In the past, is has been concluded that the ores in British Columbian mines do not go below approximately 2,000 feet, and to that depth only in a few instances. Consideration of the depth to which ores have been mined in the Province appears to support this view. The figures shown in the accompaning table have been gathered from various sources and are approximate.

Jan 1, 1935