Search Documents

By A. G. Beer

The evolution of microstructure is examined during the annealing of hot worked magnesium alloy AZ31. The influences of deformation and annealing conditions on the developed microstructures are assessed. It is found that annealing at a low temperature (300 °C), after deformation at a low temperature and strain rate (300 °C and 0.001 5-1 respectively), results in the development of abnormally large grains. With increasing values of Z (lower temperatures, higher strain rates), static recrystallization of the dynamically recrystallised structure takes place; smaller annealed grain sizes are attained and the time at which coarsening begins is reduced. Whilst both the deformation and annealing conditions influence the time it takes to reach a stable annealed microstructure, the grain size attained is governed solely by the prior deformation conditions employed.

Jan 1, 2006

By Angela L. Paveley

Economic viability of base metal mining is complicated by a volatile market that can cause fluctuations in the growth and stability of the mining industry. Nickel is mined primarily for use in manufacturing industrial stainless steel and plating materials. It is essential that nickel production be sufficient to respond to current and future market demand. A Post-Pillar cut and fill mining complex is currently producing nickel sulfide in Northern Manitoba. From 2006 this area has shown a steady increase in the annual production, rising from 11 million pounds to 25 million pounds in 2010, and accounting for 33% of the total production for the Manitoba Operations. It is expected that fine-tuning the mining process can safely enhance ore recovery, improve production consistency, and increase economic viability of the deposit. The Post-Pillar Optimization study was initiated by the local technical and operational departments at the mine and analyzed from July 2010 to March 2011. The purpose of this study was to determine if portions of non-recoverable pillars can be slashed without jeopardizing pillar strength. This ideal case would optimize ore recovery and reduce variability in the ore mining rate. Numerical modeling and geo-mechanical material properties analyses, completed by the rock mechanics group, define the maximum drift width at 32 feet and the minimum pillar width at 18 feet. Thus, it was suggested that up to 3 feet could be slashed from two sides of the standard 24 foot pillars without damaging ground integrity. The field data collected indicates that additional ore could be recovered without compromising the safety of the workplace and the integrity of the complex. Consequently, technical and operational groups work jointly to achieve pillar optimization. Approximately 500,000 pounds of nickel was extracted from the complex via pillar optimization from July 2010 to March 2011. Economic analyses show the pillar optimization method developed for the mining complex is a proven, value-added opportunity. The mining complex remains a safe workplace and has retained ground integrity.

Nov 1, 2011

By R. Roufail

Mineral liberation is accomplished by comminution and is the first step towards achieving successful downstream processes such as flotation or leaching. In metal mining, one of the most effective comminution methods that is used to grind particles below 10 microns is stirred milling. In this paper the study of particle breakage mode vs. mill operating parameters is addressed. Stirred mills' grinding action is mainly attrition, but operation can be manipulated to include breakage by compression or impact loading. Macro and micro analysis of particle breakage and grinding mechanisms are correlated. Macro analyses convey information that relates grinding mechanism to particle size and shape. It is speculated that the breakage mechanism in the horizontal stirred mills is massive fracture for the coarsest particles and attrition (abrasion) close to the grinding limit where the size reduction ratio approaches 1.0. For micro analysis, the particle breakage mode has a direct impact on fracture type either transgranular or intergranular. Intergranular particle breakage leads to higher mineral liberation compared to transgranular breakage. Similar minerals would have more homogeneous properties that convey a stronger bond compared to dissimilar, heterogeneous mineral bonds. Transgranular fracture requires higher energy than inter granular fracture; trans granular fracture toughness of pure single phase mineral is about 10-14 % higher than the intergranular fracture toughness. This communication presents the results of an investigation to assess how operating conditions can affect trans- vs. inter-granular breakage.

Jan 1, 2009

By R. Sharma, I. Miskovic, S. Miskovic

Solvent extraction (SX) is a widely used method for the extraction of copper from pregnant leach solutions or other ionic solutions in hydrometallurgical applications. About 17% of total refined copper production worldwide is produced using SX followed by electrowinning (EW). Conventional SX units, such as mixer-settlers, consume a large amount of extractant, offer poor process control and yield low extraction efficiency. Extraction efficiency is poor due to low specific interface area, crud formation, emulsification, and slow phase separation stage. Micro solvent extraction (micro-SX) is a rapidly developing technology that provides an opportunity for improved process control, higher extraction efficiency, lower residence time and, as such, has a potential to reduce the environmental footprint of SX operation. In this research, extraction of copper ions in an acetate buffer media is investigated using D2EHPA with kerosene as a diluent. Chemical factors such as extractant concentration and ionic concentration of aqueous phase are varied to determine the optimum conditions. Subsequently, the extraction efficiency and reaction time of new micro-SX reactors are compared against previous bulk SX studies. Extraction in the microfluidic reactor was observed to be faster with a residence time more than an order of magnitude lesser than bulk SX. This study forms a prelude for developing new modular micro-SX units which will enable continuous, effective, and safe operation on a large scale. In future studies, numerical and analytical models validated through this work will help eliminate rigorous experimentation and enable faster design and fabrication of micro-SX units. INTRODUCTION Conventional industrial solvent extraction (SX) units such as mixer-settlers, extraction columns present various disadvantages. Low specific interfacial area, crud formation, and emulsification in industrial reactors lead to long extraction times and severely hamper extraction efficiency (Priest et al., 2011; Chen et al., 2017). Microfluidic extraction considerably improves upon the current extraction practices by (1) creating a large surface to volume ratio that enables rapid mass transfer across the interface, (2) better process control, and (3) easier separation of phases (Kashid, Renken, & Kiwi-Minsker, 2011; Ciceri, Perera, & Stevens, 2014). These factors establish micro-SX as a crucial mode for process intensification. Although, a micro SX unit has significantly low processing volume than conventional extraction methods, their throughput can be increased via massive parallelisation (‘numbering up’), which is an area of active research (Darekar, Singh, Mukhopadhyay, & Shenoy, 2016a; Kriel, Woollam, Gordon, Grant, & Priest, 2016).

Jan 1, 2019

By S. Shokri

The increasing size and complexity of mega construction projects result in having several geographically distributed stakeholders, collaborating with each other to successfully deliver the project. Electronic Product and Process Management Systems (EPPMS) are recently emerging to facilitate the collaboration between stakeholders, reduce the surprises and issues, and improve the project productivity. These are commercially successful but evolving systems. An important component of EPPMS is the Interface Management System, which aims at formalizing and automating the communication channels between stakeholders. An interface is generally considered the link between construction elements, phases, or stakeholders. An interface Management System (IMS) involves five iterative steps: (1) Interface Identification, (2) Interface Documentation, (3) Interface Transferring, (4) Interface Communication, and (5) Interface Closing. A fundamental part of step 2 is recognizing different roles in dealing with interfaces. Each stakeholder is assigned a different role, such as responsible, accountable, consulted, and informed. In a mega project, several thousands of interfaces exist with complex relationships between stakeholders. Therefore, identifying stakeholders with higher responsible roles has been requested as useful information to the project owner in dealing with some of the project risks. After the interfaces are determined, and the responsibilities are allocated, the critical stakeholders are identified using the centrality concept in Social Network Analysis. The critical stakeholders can be determined at the highest level, considering all types of interfaces, as well as for each specific type or discipline-related interfaces. The proposed methodology is applied on a hypothetical offshore project with over 500 interfaces. In fact, this project is a simplified representation of a real scale Liquid Natural Gas project. In order to reduce the complexity of calculations and clarity of explanations, the simplified case study is used. By implementing IMS in mega projects, different parties not only formalize the communication between each other, but also gain better visibility concerning their roles and responsibilities. In addition, the owner benefits from analysing the complex relationships between stakeholders to further identify critical ones, along with other criteria like package cost, stakeholders? experiences, etc.

Aug 1, 2013

By Alan B. Morrow, William A. Poe

"Minerals processing operations are constantly challenged with improving production rates, yields, energy efficiency and process stability. Advanced Process Control has proven to be an effective tool for improving operations by capturing the full process capabilities consistently. However, the velocity of applying the technology as well as the sustainment of these significant benefits has been hampered by the usability of the software and adaptability of the applications.Some of the new technology developments that improve the usability and adaptability of advanced process control include:• modern and intuitive user interfaces,• customizable models to support unique process behavior,• fast and flexible OPC connection tools,• automated model building,• integration with first principles dynamic models and• improved performance monitoring.This paper will briefly discuss the new technology developments that have improved the usability and adaptability of advanced process control and how this can affect minerals processing operations.In today’s environment, Minerals Processing plant managers continuously face new challenges and requirements including:• higher energy efficiency,• increased run lengths,• reduced product quality variability,• reduced emissions,• higher availability, and• lower operating costsOperating a unit to meet these challenges in real time is not easy for operators and conventional process control systems. However, innovatively using existing technologies in Minerals Processing plants can improve operations on a minute by minute basis and reap significant benefits.Advanced Process Control (APC) can extract the maximum performance benefits from existing equipment while respecting plant operating constraints. Expensive capital projects to upgrade equipment are not always necessary. Advanced Process Control can deliver significant economic benefits by maintaining the plant at its most profitable point as conditions change."

Jan 1, 2016

By J. B. Rubenstein

This work demonstrates the feasibility of using confocal surface profilometry to measure and characterize wear of graphite anode surfaces. This method was tested using anode samples that were electrolyzed for 24 hours in a laboratory-scale magnesium cell with a high oxide molten salt electrolyte. The oxide produced accelerated wear on anodes designed for low oxide electrolytes. Contour maps, which are effective at displaying non-uniform wear, and total graphite consumption values were generated from the collected surface coordinates. Along with both qualitative and quantitative analysis capabilities, this measurement system was shown to have a fine resolution and a low detection limit.

Jan 1, 2004

By K. G. Markkola

Since 2005, Compafifa Contractual Minera Candelaria (CCMC) has defined various strategies which aim to optimize the usage of the available energy in each of the SAG grinding circuit modules (SABC-A configuration). For this purpose, the use of larger size balls along with operating with an optimum balls/load ratio has been implemented. Additionally, in the ball mills, the amount of balls in relation to the equipment's usable diameter has been optimized. In the pebble crushing circuit, the percentage of material passing 12 mm (112 in) product has been increased by 15% by: (1) modifying the crusher mantle profile, (2) implementing a strategy for maximizing the power in each crusher, (3) using continuous improvement tools (Lean - Six Sigma), (4) redesigning SAG mills discharge grates, and (5) changing discharge grates in order to control the crusher feed size distribution profile. All these activities have improved plant throughput by 1,000 t/d with no significant capital investment. As part of the energy consumption optimization study, we have considered determining the optimum operational rate of each SAG mill, in relation to the mill liner life and also the improving the control strategy in conventional grinding.

Jan 1, 2007

By Tamas Kekesi, Gergo Rimaszeki, Tibor Kulcsar

The efficient purification of soldering waste material can be achieved in a single operational step by the electrolytic refining in pure hydrochloric acid - tin-chloride media. The complex formation of the ionic species may offer a beneficial level of natural inhibition. Using the PCR (periodic current reversal) technology, is efficient in affecting the morphology of the cathodic deposit. In order to optimize the process, the investigation of the solution stability and the electrode reactions is essential. The natural tendency of the Sn(II) oxidation and precipitation can be overcome by properly controlling the concentration of the main components and the ratio of Sn(IV)/Sn(II) in the electrolyte solution. Polarization curves were obtained for different concentrations tin and hydrochloric acid. Conclusions referring to the electrode reaction were derived from the overvoltage - current plots. The morphology of the deposit can be correlated with the exchange current density, also determined from the polarization curves. The cathodic current efficiency and the morphology of deposited metal are affected by the distribution of tin species and the principal electrolysis parameters.

Jan 1, 2011

By Chun-Sheng Liao, Chun-Hua Yan, Sheng Wu, Fu-Xiang Cheng

"INTRODUCTIONChina is providing more than 90% of the rare earth products consumed in the whole world. Acidic extractants are commonly used in the extraction separation of rare earths. Saponification of the acidic extractants by basic substances is usually necessary for the purpose of increasing and stabilizing their extraction capacity, and meanwhile inorganic acids are required for both scrubbing and stripping. Thus acids and bases are the main consumed chemicals, and the resulting salts are the main pollutants generated by rare earth separation processes. Currently, due to increasing environmental concerns in China, rare earth solvent extraction separation techniques are being developed to reduce both consumption and emission of chemicals, which is driving the developments on both theories and processes for solvent extraction separations.In the 1970s Prof. Xu et al. developed the Theory of Countercurrent Extraction (Xu, Li, & Yian, 1985). In recent years, the development of novel processes for rare earth separation has moved beyond the earlier theory. One rare earth separation process, the so-called hyperlink process, has been developed in the past decade and proven in industrial practice to dramatically reduce both the consumption and emission of chemicals during multi-component solvent extraction separations, and therefore is now widely used in the Chinese rare earth separation industry (Liao, Wu, Cheng, Wang, Liu, Zhang, & Yan, 2013). The present article will give a brief review of the development of the theory of the hyperlink processes, and the hyperlink separation flowsheets for typical rare earth mines in China designed using the theory.HYPERLINK PROCESSES (LIAO et al., 2013)A flowsheet of multiple-component separation consists of a couple of separation units. The units of a conventional flowsheet separately consume chemicals for saponification and scrubbing and discharge wastewater with resulting salts. In contrast, the separation units in a hyperlink process are hyperlinked and thereby the chemical demands of the whole flowsheet are decreased. For a feed containing t components of A1, A2, …, and At, it has been proved in theory that the separation mode of (AtAt-1…A2)/(At-1At-2…A1) is preferred in a single separation unit. The hyperlinking between separation units can have two forms. The link between two units locating at a same separation level, such as between (A4A3)/(A3A2) and (A3A2)/(A2A1), is known as horizontal hyperlinking. The link between two units located on different levels, such as between (A4A3A2)/(A3A2A1) and (A3A2)/(A2A1), is known as vertical hyperlinking. Both the hyperlinking forms have been proven to save chemical usage and consequently to lower the pollution emissions in industrial practices as well as in theory."

Jan 1, 2016

"In today’s world of complex projects, where engineering and execution are supported by a high level of project management and systems, how critical is the human factor in design engineering. Based on his involvement on a variety of projects, Tony Lipiec will relate his experiences as the impact of 4 factors: the ‘team’ involved in the design and execution of the project; the project and information systems supporting the project; the impact of scope, time, and budget; and finally the selection of the proper success criteria to judge the project and the people who have enacted the project.The discussion of the team will relate to the quality of people and the impact of their knowledge, attitude and experience. It will also look at the relationships and interests of the various stakeholders. Decision making and taking responsibility will be discussed.Supporting the team are the management, document and information systems. The value that these systems bring to the project as a whole will be examined. How project size impacts the applicability of the systems will be discussed.Scope, time and budget are recognized as critical. Reference will be made to the interplay between these components which are vital to project success. The issue of iterative design and whether it is necessary will be considered together with the development of supporting technical information.Finally the selection of the proper success criteria and the awards provided to the team can have a big impact on the final, production success of the project. The author will discuss his views on the impacts of these on EPCM projects."

Jan 1, 2016

By A. Zangooi, J. A. Finch

Flotation is a separation process based on the collection of particles on the surface of bubbles. Flotation machines disperse air into bubbles using a variety of techniques. The characteristics of the bubble population are strongly affected by the selection of frother type and concentration. As metallurgical results depend on the bubble distribution, the measurement of frother concentration is vital to understand and control performance. A previously developed colorimetric technique was refined to work with low solubility frothers and to increase daily analysis rate. Field-testing demonstrated that the method is robust, reliable and accurate. As well as relating frother concentration to gas dispersion measurements, the results can be used to answer operational questions including: how well a frother dissolves, how reliable and stable frother delivery is, how evenly frother is distributed down a bank, and whether frother distributes between the pulp and froth zones. Some of these points are illustrated from plant experiences. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By W. Dan Hausel

"Abstract-Hundreds of diamonds have been found in the United States. The majority of the discoveries occurred during the 19th century as a by-product of placer gold mining. Most of these early diamond finds have no known source, and in many cases are situated in areas unfavorable for diamond exploration based on current models that require kimberlite or lamproite to be emplaced in a stable Archean craton or Proterozoic craton margin.Diamonds have also been recovered in situ from lamproite at Murfreesburo, Arkansas, from kimberlite in the Lake Ellen region of Michigan, and in several kimberlites in the Colorado-Wyoming State Line district. Unverified reports also suggest that diamonds may have been recovered from other related intrusions at a number of localities in the United States."

Jan 1, 1995

"Background:The recorded coal production in Nova Scotia from 1863 to 1980 was 390, 000, 000 short tons. This extraction was associated with an estimated 60,000,000 short tons of discarded material. This mining discard and coal washing plant reject are located in numerous, varying sized dumps throughout the mining areas. Approximately 70% of these dumps are in the Sydney coal field region of Nova Scotia.The coal content of these dumps varies from 10 to 30% coal with an average of 18%.Energy Costs:The explosion of energy costs in the mid-1970 's greatly increased the sale price of thermal coal which made recovery of coal from some of the dumps economical. The environmental spin-off of these operations will be the rehabilitation of the dumps upon cessation of the coal reclamation operation.Cape Breton Development Corporation, the owner of most of the dumps in the Sydney coal field was receptive to an approach by Selco of reclaiming coal from their dumps. The technology to be used, had been developed by an associate firm in the United Kingdom on similar mine dump situations."

Jan 1, 1983

By W. Dan Hausel

"Hundreds of diamonds have been found in the United States. The majority of the discoveries occurred during the 19th century as a by-product of placer gold mining. Most of these early diamond finds have no known source, and in many cases are situated in areas unfavorable for diamond exploration based on current models that require kimberlite or lamproite to be emplaced in a stable Archean craton or Proterozoic craton margin.Diamonds have also been recovered in situ from lamproite at Murfreesburo, Arkansas, from kimberlite in the Lake Ellen region of Michigan, and in several kimberlites in the Colorado–Wyoming State Line district. Unverifed reports also suggest that diamonds may have been recovered from other related intrusions at a number of localities in the United States.IntroductionTo date, diamonds have been recovered in situ from kimberlite in the Colorado–Wyoming State Line district and from a kimberlite in Michigan. Additionally, diamonds have been recovered from lamproites in Arkansas. Diamonds have also been reported from kimberlite in Kansas, and from peridotite in New York and Maryland. However, these latter reports have not been verified."

Jan 1, 1995

By D. H. Schwarz

The performance of proton exchange membrane (PEM) fuel cells depends on catalyst layer composition and structure. Experimental observations reveal that state-of-the-art catalyst layers consist of microporous agglomerates of carbon-supported catalyst sites bound together by polymer electrolyte. In between the agglomerates are macropores which provide pathways for the transport of gaseous reactants. In this work, three-dimensional, multicomponent and multiphase transport computations are performed using a computational fluid dynamics (CFD) code (FLUENTTM) with a new PEM fuel cell module, which has been further improved by taking into account the detailed composition and structure of the catalyst layers using a multiple thin-film agglomerate model. In this model, it is assumed that thin films of polymer electrolyte and liquid water surround the catalyst sites. The results of CFD computations show that transport limitations associated with the thin film of polymer electrolyte and the presence of liquid water in the catalyst and gas diffusion layers have substantial negative effects on PEM fuel cell performance. Also, the results of computations with variable distributions for a given precious metal loading show that, in general, uniform catalyst loading provides the best fuel cell performance.

Jan 1, 2005

By K. Nikkhah, N. Dhadli, G. Freeman

Ammoniacal pressure leaching operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation since 1954. Recent improvements have significantly increased the capacity of this circuit. The computer modeling of this process has proved to be a valuable tool in facilitating the evaluation of different operating scenarios in an effective manner. Reagent response in the ammonia leach of nickel and cobalt sulphides is examined using the dynamic process simulation capabilities of IDEAS(TM) software. The dynamic simulation enables accurate measurement of the sensitivity of the process to variables such as temperature, feed rate and ammonia concentration as well as compartmental analysis of metals concentration, pulp density, vent gas composition, and the formation of specific complexes. The complexity of the ammonia leach process makes it a logical choice for evaluation by computational analysis. The methodology for dynamic modeling of a pressure leach process is presented.

Jan 1, 2005

By Garth D. Kirkham, James P. Siddorn, Hendri Falck

"Abstract - As an integral part of the Geological Survey of Canada’s EXTECH III Project, a threedimensional computer model has been created of the Con and Giant gold mines in the Yellowknife Greenstone Belt. The Yellowknife Mining Camp has produced a great deal of gold (over 15 million ounces, or 400 000 kg) in the past sixty years and the prevailing assumption is that the mines are at the end of their lives. However, the potential for discovering additional resources using new ideas and technology, and maximizing use of existing data, offers an opportunity to sustain the old mining operations and maintain their contribution to the community.The objectives of this study included the compilation and creation of a three-dimensional Geographic Information System model (combining 3D subsurface data with surface information) to provide a framework for concurrent structural and alteration studies, and to encourage new exploration in the area. A secondary objective was to retain the data in digital format as a historical reference for future remediation efforts, and to document a portion of Canada’s rich mining history.The end result is a database and set of models that have been instrumental in facilitating further exploration in the area, as well as in developing targets for future exploration and mining activities. In addition, the EXTECH III 3D GIS model has made a valuable contribution toward the understanding of the arsenic remediation issues at the Giant mine, and has served as a tool in support of a variety of highly technical engineering studies and for communicating information and problems to the layman and community as a whole."

Jan 1, 2003

By K. Sasaki

Ventilation measurements were carried out in a shallow underground-quarry space with relatively large internal volume of 14,600 m3 in order to evaluate its effective ventilation characteristics. Based on air velocity measurements with an ultrasonic anemometer in the exhaust airway connected to the space, it was found that the space was ventilated by natural ventilation airflow with intermittent changes in direction. It was difficult to measure the ventilation flow with typical methods of flow measurement provided from the intake portal and throughout the mine, because the cross-sectional area and volume of the openings were too large and the flow was variable. In the present study, a tracer gas method was applied to evaluate the effective ventilation airflow rate in the space. A photo-acoustic infra-red gas monitor, highly sensitive to SF6 gas used as a tracer gas, was set in the space to determine air exchange rates from gas concentration-time decay curves. The seasonal variations of airflow and thermal environment in the space were investigated through 13 sets of measurements taken over 15 months. Airborne rock dust concentrations were also measured at same time in the opening. The correlations between the effective ventilation airflow rate, thermal environment and dust concentrations in the opening space were analyzed and are discussed based on the presented measurements taken during year. It is concluded that seasonal variations in effective ventilation flow and the dust concentration are mainly due to differences in air temperature in the space, as affected by the rock?s surface temperature and atmospheric temperature. In summertime, the air temperature and associated air density difference generated lower natural ventilation flows resulting in higher dust concentrations.

Aug 1, 2013

By R. Tessier, R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. The paper presents findings in the on-going testing of various sizes and shapes of grinding media. Breakage rates are used as an aid to assess the effect of grinding media. Results of empirical and phenomenological analyses demonstrate the importance of adequate selection of media sizes on the milling operation.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mine near Bathurst, New-Brunswick. The No. 12 ore body is an extremely fine grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite. The operation is currently processing 10,500 tonnes of ore per day in conventional crushing, grinding, differential flotation and dewatering circuits. Details on the circuit can be found elsewhere (e.g. Hendriks and Ounpuu, 1985; Grant et al., 1991).The mill has operated for more than 25 years and despite the past milling experience, there has been much disagreement as to the required grind size. Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37µm) and averaged slightly over 71%in1992. Results from mineralogical analysis (Petruk and Schnarr,1981; Coleman, 1988), Brunswick metallurgical laboratory (Grant et al., 1991; Shannon et al., 1992) and Lakefield pilot plant tests (Hendriks, 1984; Hendriks and Ounpuu, 1985) clearly indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15-25µm range."

Jan 1, 1993