Search Documents

By Audrey Wagenaar

Introduction ?? Rising public pressures are being placed on companies worldwide to protect the environment and the health and safety of their workers and local communities. ?? International bodies and shareholders want to make sure developments and companies can meet internationally acceptable standards for EHS. In 2005, Golder Associates was asked by the IFC to conduct a comprehensive review and update for their Environmental Health & Safety Guidelines including the mining sector.

May 1, 2008

By B. J. Cunliffe

"Filter cloth in the mining industry is an ambiguous title asthis suggests filter cloth use from underground ventilation to the refining processes. The time allowed for this paper would be better served in con-centrating on vacuum filters common to all mine mills and to offer some simple guide lines to the mill metallurgists in the choice of filter cloth for this type of filter.The requirement of the filter cloth is to separate solids from liquids under a vacuum head by forming a permeable layer of solids or cake, through which liquids can flow until the panel or disc sector leave the slurry tank and to continue to pass residual moisture from the cake formed during the cake drying cycle, and to discharge the cake on air-blow so that the cycle can be repeated.Whilst the mill metallurgist should not be expected to under¬stand all aspects of filter cloth manufacturer, it is however, advantageous for him to understand a little of the textile language associated with filter cloth for his own protection against ""trial-and-error"" methods, which are both time consuming and costly.If improvements are to be made over existing filter cloth in use an examination of the limiting factors of the cloth used should be made and the major causes for removal determined, e.g. cloth blinding, high moisture in cake, poor cake discharge on air blow, mechanical damage to cloth.As each of the limiting factors mentioned has a bearing on the choice of fibre used, the yarn type and weave of a suitable cloth, an under-standing of these points will assist the mill metallurgist in avoiding repetitive trials offering little degree of success."

Jan 1, 1971

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By S. Simukanga, J. Masinja, P. A. Bepswa, A. N. Mwale

Screening is an important operation in dry and wet closed circuit mineral processing applications. Most of the operations have seen the benefits of using fine wet screens in primary grinding sections where the product is relatively coarse, and screens can handle the tonnage. Although many models are available, most of them are confined to dry and wet coarse screening applications. Most models do not give good predictions for wet fine screening. To facilitate model development, pilot plant tests were performed using a single deck Derrick Screen at aperture sizes of 45µm, 75µm, 106µm, and 150µm. Experimental data for a range of feed solids concentrations and flowrates was collected and used to calibrate the performance of the screen under the different operating conditions. The results showed that the performance of the screen deteriorated with an increase in feed solids concentration, and, similarly with an increasing feed flow rate. The percentage of fines carryover also increased with the reduction aperture size. The carryover was even more pronounced at higher feed rates and solids concentrations. A model was developed for predicting the performance of fine wet screening. Data from the test work was used to compare the actual and predicted results, and to calibrate the model. Additional independent data was used to validate the model and assess its limitations. This model will give an expected screen performance based on the initial feed conditions. It incorporates screen design parameters that allow for an estimation of a suitable screen size for a desired performance based on given feed conditions. This paper discusses; the results from the test work performed, the model development and its limitations.

Jan 1, 2016

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

"High Pressure Grinding Roll (“HPGR”) technology is applied in a broadening range of minerals processing applications for relatively wet or moist materials. HPGR grinding of dry material or involving drying and air classification is more common, for example in cement manufacturing. A number of minerals processing plants are also operating with dry material, either due to process reasons, such as considerations of preceding or subsequent process stages, or as dictated by local conditions of arid areas and scarcity of water. The present world-wide expectation of decreasing availability of water supply urges us to look for alternatives that minimize water consumption.Recently established and envisaged future HPGR applications with dry ores have indicated that the technology of dry crushing and classification as practiced in cement and limestone grinding can be applied in minerals processing. Moreover, dry technology could very well be applied for generating a final fine product at sizes near or below 100 microns, as may be required for beneficiation by, for instance, flotation, magnetic separation or tank leaching.Dry HPGR grinding requires special attention in maintaining suitable process economics, when considering power input in grinding, drying and classification. In some cases, HPGR capacity and roll surface wear life may be negatively affected by a lack of moisture in the feed.This publication summarizes some of the features of, and experiences in dry HPGR applications. This includes design aspects of the classification system and discussion of the wear protection of the roll surfaces. The paper also includes examples of operational experiences of dry practices in minerals processing and cement plants."

Jan 1, 2012

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By C. G. Anderson

Alkaline sulfide leaching technology (i.e. ASL) has been studied, presented and published throughout the literature and utilized in some current engineering studies. Yet, the actual industrial applications are very few and the knowledge about these is very limited. Hence, a large gap between the laboratory, publications, engineering studies, and the actual industrial plant exists. Recent studies of ASL applied to copper enargite concentrates definitively bear out this dichotomy. Hence, this paper will seek to dispel the common misperceptions that continue to surround the selective industrial ASL hydrometallurgical technology. For edification of the reader, a listing of ten common misconceptions and myths is listed. As well, ASL history, fundamental aspects and a new flowsheet application for simultaneous gold and high purity antimony oxide production from low grade materials is included. The associated estimated economic considerations are also included to heighten enlightenment about the application of this industrially proven technology.

Jan 1, 2014

By Ken Musgrave

"A program is described that helps managers and supervisors control maintenance more effectively. Work- order generation, preventive maintenance, repair parts inventory, planning and scheduling, reporting, analyzing costs, printing purchase orders and other functions are covered. Flexibility often permits integration with other programs such as payroll, cost accounting and materials management.The Role of MaintenanceMaintenance provides a service to allow the rest of the operation to do its job effectively. Its success should not be measured by maintenance cost alone, but also by its effectiveness in reducing downtime and maximizing production. It can make sense to spend more maintenance dollars if this results in an even greater contribution from increased production.The Cost of MaintenanceIn mining companies, maintenance costs can be as much as half of operating costs. Maintenance has generally not been given the management attention that an expenditure of this magnitude deserves."

Jan 1, 1986

By F. Cheuk, E. Krause, V. G. Papangelakis, G. A. Moldoveanu, S. Abendschein

Systematic studies have been conducted at the University of Toronto in order to evaluate lanthanide extraction from clay minerals from different geographical regions. It was found that rare earth elements (REE) are easily recovered into an aqueous solution via an ion exchange mechanism by leaching with electrolyte solutions containing monovalent cations under ambient conditions. In this study we assessed extraction levels of individual REEs as a function of initial clay composition and leaching conditions. It was found that, in spite of variations in clay origin, all clays consistently reached peak REE extraction levels with fast kinetics. However, terminal extractions were clay-specific. The feasibility of using seawater as a leaching solution and potential synergies with ammonium sulphate as a lixiviant was also investigated. Seawater was found to be inferior to using ammonium sulphate, and provided no observable synergy in leaching performance when used together. The aqueous phase trapped in leached clays was shown to contain significant amounts of REE, as demonstrated in clay washing tests. Techniques to improve the REE concentration in leachate through process variations were investigated. However, it was found that most techniques capable of increasing REE concentrations in the resultant leachate also resulted in reduced REE extraction.

Jan 1, 2014

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By Robert B. Parsons

"The February 18, 1987, Federal Budget contains a proposed amendment which would simplify somewhat the ""successor corporation"" rules in the Income Tax Act. Despite this amendment, though, the important successor rules will continue to be relatively complex.IntroductionThe February 18, 1987, Federal Budget papers propose an income tax amendment whereby the so-called ""successor corporation"" rules would be revised by removing the present provision which limits the application of these rules to a maximum of two ""successions"". The successor corporation rules represent one of the most complicated sets of rules in the Income Tax Act. This month, Tax Notes seeks to explain these rules and the proposed amendment in simplified terms.Basically, the successor rules provide a mechanism for transferring unused exploration and development expenses from one taxpayer to another , in specified circumstances. The aforementioned limitation of two successions refers to the rule which allows a maximum of two such transfers with respect to any particular pool of deductions."

Jan 1, 1987

By Silvio E. Kruger

Real time measurement of wear and corrosion provides crucial information needed to determine an optimal schedule for corrective maintenance and is a powerful tool to maximise equipment availability and reliability. It also leads to savings from optimized spare parts handling and helps to avoid costs of accidents and their negative impact on safety and the environment. This paper presents the technology of ?painted-on? ultrasonic transducers that can be integrated to structures and accurately measure the remaining thickness and therefore determine wear or corrosion losses. These transducers have a small footprint, a performance comparable to other commercially available ultrasonic transducers and can sustain temperatures as high as 400ºC. The application of this technology to mining equipments and its potential benefits are discussed.

Aug 1, 2013

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011

Oct 1, 2010

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By Alfredo Bambaren

First Encounters between Communities and Mining 1. Importance, meaning and process 2. Antamina?s study case 3. ?Self-organization? theory (NLP) 4. The story we tell, the values we live 1. Importance, Meaning and Process ? First encounter stays in mind as a model. ? First encounter means foundation. ? First encounter builds the story.

May 1, 2010

By M. Soleimanifar

With more and more industrial construction projects implementing RFID and other sensor-based technologies on fabrication and project sites, new innovative processes are needed to help automatically read and re-position RFID tags while reducing the cost to deploy RFID infrastructure over large areas. RFID tags are being used on construction sites to help identify the location of materials, equipment and personnel to aid in finding project critical materials and equipment required to construct the industrial facility on time and on budget. This research provides a cost-effective process for reading tens of thousands of RFID tags over large project sites from outdoor laydown yards, to warehouses to the workface where the materials and tagged equipment are installed. Based on the collected RFID and sensor data, localization mechanisms determine the most recent coordinates of the tagged components. The paper will cover analysis of RFID collected data and key lessons learned from a commercial deployment of the SiteSense® system with one Alberta-based industrial contractor, JV Driver Fabricators, at an 80-Acre module, pipe spool and structural steel fabrication site.

Aug 1, 2013

By N. Kolev, M. Poibrenski, I. Nishkov

"The following paper examines the flotation of copper porphyry ores in Assarel concentrator with focus on the reasons for low molybdenum recovery in the final copper concentrate. The copper-porphyry ore of the Assarel deposit is characterized by its variable mineral composition and high clay content, which influence the process efficiency of their concentration. Particle size distribution, chemical and mineralogical analyses have been made on various flotation products showing the distribution of the main elements of interest - copper and molybdenum. It was found that molybdenum is not concentrated into the final copper concentrate as usual in the flotation of copper-molybdenum ores but into the tailings of the copper selective flotation (cleaner tailings). An attempt to explain these results has been made with proposals to improve molybdenum flotation. Low floatability of molybdenite is caused by the ultrafine clay minerals content in both the run-of-mine ore and copper flotation streams. In order to achieve selectivity of copper minerals against pyrite a significant amount of lime is used in the plant leading to higher pH conditions, which could be another possible explanation for the molybdenite depression. The results obtained after the laboratory experiments, showed that it is possible to restore molybdenite floatability using traditional reagents such as diesel, kerosene, etc., and introducing a new polymeric reagent as froth modifier.INTRODUCTIONOne of the main technical difficulties in the area of copper-molybdenum flotation is the selective recovery of both metals, especially the fine (<40 micron) mineral particles. The problem is even more serious when Cu-Mo ore treated contains a lot of natural fine particles, predominantly clays, micas and other gangue minerals. Peng and Zhao (2011) conclude that the mineral processing industry is well aware of the difficulty in treating ores in the presence of clay minerals. Tremolada et al (2010) found that clay minerals have been named as the main problem in ore beneficiation processes due to their small size, which cause a higher viscosity in grinding. In flotation, these clay minerals have natural hydrophobicity or float by entrainment.The impact of clay mineralogy on flotation performance has been reviewed in the literature and the various deleterious roles of clay minerals have been investigated (Bulatovic, Wyslouzil & Kant 1999; Jorjani et al, 2011; Farrokhpay, Bradshaw & Dunn, 2013). It is widely accepted that the actual flotation recovery problem appears to be caused by the properties of these fine particles: small mass (and/or momentum) – high interfacial free energy (Rubio et al., 2007; Farrokhpay, 2011). In most cases, the loss in recovery is found to be insignificant, but the detrimental effect on the concentrate grade is found to be more prominent. The main reasons for the flotation inefficiency are the low probability of bubble-particle collision and adhesion, formation of dense froths and as a result - low process kinetics. A great deal of fine valuable minerals is discarded as slime in flotation due to lack of effective recovery methods."

Jan 1, 2016

By M. J. Brodie

"The decision to proceed with mine decommissioning, generally involves a number of complex and independent factors. These factors, including potential for re-opening, legal requirements, contingent liability, asset depreciation, due diligence, and public relations are discussed in the context of the financial implications on a net-present- value basis. It is concluded that the decision to delay mine decommissioning is commonly not in the best financial interests of the mine operator. Some measures to reduce decommissioning costs and expedite the process are presented.IntroductionThe primary audience for this paper is mining executives, although it should be of interest to all professionals involved in the planning and carrying out of mine decommissioning. Historically, mines were abandoned, not decommissioned. Then, as decommissioning became required, it was assumed that salvage revenue would pay for decommissioning. During the I980s, it became apparent that mine decommissioning costs would exceed salvage revenue for nearly all sites, and that a substantial net cost for decommissioning would be realized for some sites. Throughout this period, the approach to decommissioning has evolved through the sequential addition of measures to meet the increasing regulatory burden. This has resulted in a process in which the elements of decommissioning may not be optimized with respect to each other for the most favourable net present value to the corporation. Additional considerations which are not specific to mine decommissioning, such as environmental policy, due diligence and public relations, may now come to bear on the decision-making process.This paper addresses the issue of mine decommissioning as a three-step process. The first step involves identification and evaluation of all of the issues that relate to mine closure, the most importantof which is the potential for re-opening of a mine. Assuming that it is decided that a mine is unlikely to re-open, the second step is to determine when to carry out the decommissioning work. This aspect is examined through a net present value (NPV) approach. Finally, details regarding who does the work and how the various tasks are divided up must be resolved.Every mine is a unique concentration of minerals at some specific location, hence the development, operation and closure of a given mine must be regarded as a special case. Superimposed on the site-specific considerations are the size, history and financial status of the associated corporation."

Jan 1, 1995

By Janice Zinck, Ian London

In recent years, the secure supply of critical and technology metals has become increasingly important tomajor industrialized economies that seek to sustain their industrial base and develop advanced technologies, such as clean energy. Canada, with its significant reserves of rare earth element (REE) and other metals, has an opportunity to supply some of the global demand for these materials. However, to transition from promising mineral deposits to marketable products, investment in strategic research and development (R&D) and expertise is needed to address the complex technological challenges around the production, separation and processing of these metals, and to better understand the global market for these key commodities. To this end, in its April 2015 budget, the Government of Canada committed to invest $23M over 5 years to accelerate production of REE and chromite/ferrochrome. The goal of this program, developed in close association with industry, is that Canada contributes a sustainable supply of REE to the global market. The research and development program will provide the technological capacity to establish a Canadian REE industry. This paper will discuss REE R&D advances achieved in the first year of the program in areas of mineral characterization, beneficiation, leaching, separation and environmental management and will highlight the Canadian model of collaboration where industry (e.g. prospective producers, technology companies), government, academia and other stakeholders work closely to ensure that the R&D is targeted, innovative and effectively deployed and commercialized.

Jan 1, 2016