Search Documents

By Nicolas Gatelier, Sophie Laurent, Thierry You

Hard-rock caverns for hydrocarbon storage are a very particular type of underground facility controlled not only by local administrative and regulatory constraints that can be very specific, but also by the possible risks of geotechnical or geomechanical failure. Each such facility throughout the world is a prototype that needs to be adapted to very different site conditions. The straight forward application of design methodologies from relatively similar fields (mines, tunnels) can be very useful, but risks holding back the scientific and technical improvements needed by an engineering industry in full development. Here we look at various case histories and at problems that have been raised where recent attempts at standardization would appear to have been ill adapted, and where storage designers, through experience and judgment, may still provide innovative engineering solutions.

Jan 1, 2015

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level indicated can be in considerable error, largely because of variations in froth and collection zone bulk densities. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the collection and froth zone. This probe detects the position of the interface to an accuracy of ± 5 cm. The probe can be used while the column is in operation, which allows for on-line recalibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 m in diameter) are described.

Jan 1, 1990

Agenda 1.Energy consumption and energy costs ?focus and failings 2.Energy efficiency methodologies, people and supporting tools 3.Energy cost saving case studies from three minerals processing plants 4.The operations team and the supporting role of Operations IT 5.Conclusion: Reducing energy consumption and energy costs There are many good Energy Efficiency Methodologies ?Energy and GHG Emissions, Management Guidance Document, The Mining Association of Canada ?Energy Savings Toolbox ?An Energy Audit Manual and Tool, Canadian Industry Program for Energy Conservation (CIPEC) ?Lean and Energy Toolkit, Achieving Process Excellence Using Less Energy, www.epa.gov/lean ?Energy Efficiency Opportunities Assessment Handbook, www.energyefficiencyopportunities.gov.au

May 1, 2010

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By G. Sperlins

"IntroductionBrenda Mines Ltd. is a low-grade open-pit mining and milling operation located near Peachland, B.C. Brought into production in late 1969, the plant treats an average of 30,000 tons per day of an ore that contains 0.130% copper and 0.030% molybdenum.The operation is divided into six areas of responsibility, namely the mine, mill, plant, accounting, industrial relations and purchasing /stores departments.The purchasing and warehousing area handled in excess of 11,000 items valued at $31,000,000 in 198J. Over and above this, the warehousing area issued in excess of 74,000 line items valued at $15,000,000 during that same period.Materials Management- DefinitionWhat is meant by the term ""Materials Management""? Reference to the dictionary will reveal that a material is ""that of which anything is composed or may be constructed; the tools, instruments, implements', etc. for doing something"". Management is defined as ""the act, or manner of managing; the skillful use of means to accomplish a purpose"". Presumably combining these words defines materials management.Of greater importance are the materials managers who will carry out the function. At Brenda Mines Ltd., all employees and suppliers contribute to the materials management function. Each has a specialized knowledge of the materials used in his field. Each has a different view concerning the use and description of the same material. The key is to focus this knowledge so as to make the materials management system useful to everyone."

Jan 1, 1982

By D. G. Ingram

This paper reviews the operating and maintenance practices at Bethlehem Copper from the commencement of operations in November 1962 to the present. Cost data and wear life of major components are also discussed.

Jan 1, 1979

By George R. White

"The Phalen Colliery, the Cape Breton Development Corporation's flagship, is now producing thermal and metallurgical grade coal in Eastern Canada's Sydney Coal Field. The colliery is a drift mine operating under the waters of the Atlantic Ocean. Improved mechanization, including a 2200 tonne per hour cable conveyor, and the introduction of modern retreat longwall mining methods as part of the Phalen concept are now paying off in better productivity and low operating costs. Geological conditions within the coal field are consistent with plans for ever greater outputs in the 1990s. Although much of the current production improvement is related to uprated machine capacity and simplified mines planning there is potential for even further development in the areas of maintenance, process control and engineering. Human resource development will also be a key factor. These programs are now well under way and Phalen Colliery is poised for top results in the 1990s. Comparison of the CBDC's top producer with similar operations elsewhere in the world, quantifies that potential.IntroductionAn exciting new mining project which has recently started production on Canada's East Coast has been conceived and designed to be one of the most modern and productive coal mining operations in North America.As with all mining operations, the business is basically that of material transportation. Daily, the product is transported many kilometres from the underground face to the surface and then to washing facilities. Men, materials and equipment are transported to and from the surface and the operating faces and services, such as electrical power, ventilating air, fresh water, discharge water, communications and compressed air are supplied throughout the operation to cover operating requirements. On all accounts the operation has been designed to take advantage of the latest proven technology."

Jan 1, 1990

By X. Cao, X. -G. Chen, K. Liu

As is well known, the standard Al-Cu 206 cast alloys have extremely low iron contents, usually less than 0.15 wt. %. Recently it is found that the iron contents of the 206 cast alloys can be extended up to 0.5 wt. % through the precise control of the iron-rich intermetallic phases. In the present work, the tensile fracture surfaces of the 206 cast alloys with various iron contents are systematically analyzed to understand the failure mechanisms. Results show that higher iron contents can reduce the tensile properties (especially the ductility) of the alloys mainly due to the increasing volume percent and size of the iron-rich intermetallics. Tensile failure mainly occurs at the iron-rich intermetallics/matrix interfaces for the platelet ß-Fe, but by the self-disassociation for the Chinese script a-Fe and Alm(FeMn). Cracking is easier to initiate and propagate along the longitudinal axis of the platelet intermetallics, but it can be deflected along the branches/arms of the Chinese script iron-rich phases, making the alloy more resistant to the propagation of the cracks, and thus the Chinese script iron-rich intermetallics are less harmful than platelet ß-Fe. In addition, it was also found that the Chinese script a-Fe has even a less damaging effect compared to the Chinese script Alm(FeMn) due to the relatively small size and compact morphology.

Jan 1, 2014

By Paul Johnston

or is it? Mining Automated Loader Technology Application ? Intelligent software mounted in hardware on a remotely controlled scoop. ? Led by INCO, Sudbury, with ? C-CORE, St. John?s ? Automated Mining Systems, Aurora ? Bell Canada, Sudbury ? Laurentian University, Sudbury ? University of Western Ontario, London Completed: March 2000

May 1, 2008

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005

By C. Díaz, A. D. Dalvi, C. E. O'Neill

Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulphur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is treated in a sulphuric acid plant, and the low sulphur calcine is reduction smelted with coke in an electric furnace to yield a sulphur- deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulphur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries (Ire obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters.

Jan 1, 1994

By Z. Wu, L. N. Y. Wong

The present study develops the numerical manifold method (NMM) as a tool to investigate the progressive failure in rock slopes. The entire processes of the progressive slide surface development related to crack initiation, propagation, coalescence and degradation to eventual catastrophic failure are successfully captured. To overcome the limitation of the original NMM associated with an improper removal of the interface cohesion of the discontinuities, the displacement-dependent cohesion removal method is adopted. Simple examples of failure of rock slopes containing different arrangements of discontinuities are modeled and their results are compared with those based on the popular limit equilibrium method proposed by famous pioneers Jennings and Jaeger. In cases of coplanar non-persistent discontinuities, close results are obtained despite the differences in the consideration of the stress concentrations at the crack/discontinuity tips. In cases of non-coplanar discontinuities, since the influence of the tensile strength is considered by both the Jaegers model and the NMM, the Factor of Safety (SF) values are similar despite the difference in the failure path trajectories predicted by these two models. The results also reveal that the original NMM without the displacement-dependent cohesion removal method is always more conservative due to the improper removal of the interface cohesion. The displacementdependent cohesion method can to some extent alleviate such a limitation.

Jan 1, 2015

By Brian Mattie

Overview ?Overview of the mining area ?Description of the mining phases ?Risk assessment ?Design criteria and description for freeze drifts ?Freeze wall design ?Raisebore mining Four Main Phases: 1.Development of freeze drifts on the 520 and 590 levels 2.Freeze drilling and ground freezing to isolate the Zone 4 North ore body from water bearing sandstone. 3.Develop raisebore and extraction chambers including access drifts and ramps under freeze protection. 4.Start raisebore production mining of the Zone 4 North area.

Nov 1, 2011

By C. Díaz, A. D. Dalvi, C. E. O'Neill

"Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulphur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is treated in a sulphuric acid plant, and the low sulphur calcine is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulphur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries (Ire obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters. IntroductionReduction of sulphur dioxide emissions has been a long-standing endeavour at Inco. At the company's Ontario Division, as shown in Figure 1, sulphur dioxide emissions were reduced from about 2 million to 685 000 tonnes per year over the period 1970-1985. Most of this impressive improvement was the result of a sustained research effort which led to increased rejection of pyrrhotite from the ore during milling while maintaining an acceptable nickel recovery. Between 1970 and 1985, the combined grade of the separate nickel and copper concentrates feeding the Copper Cliff Smelter increased from about 10070 to about 'lIJ0J0 Cu +Ni and the combined S/(CU +Ni) ratio decreased from about 2.8 to 1.65."

Jan 1, 1994

By T. T. Perles

This paper will review the state of the global vanadium industry and outline the implications for the market in the coming years. Global vanadium resources and reserves will be defined. Current production of vanadium will be quantified and examined in terms of production by country, sources of raw materials for production and cost implications of the production processes. Current consumption of vanadium by country and by application will be reviewed. Vanadium supply/demand balance in recent years and the resulting impact on global inventory levels will be discussed. Projections for changes in global production, consumption and resulting inventory changes for the vanadium market in the coming years will be made.

Jan 1, 2014

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By K. Adham, T. Buchholz

"Significant capacity increases to meet new production demands can often be fulfilled through debottlenecking of an existing production facility, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. To achieve that goal, it is important to model and calculate the existing ultimate capacity of each processing plant area, and that of each key equipment sector within the plant areas. This paper describes a methodology of how process modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the sweet-spots (minimum cost points) for a plant expansion – leading to a road map of the subsequent debottlenecking project implementation.The debottlenecking technique is presented through a generic work-flow narrative which can be applied to different mineral processing studies, starting with establishment of heat-and-mass balances, drawing a bottleneck diagram, brainstorming capacity increase options, and preparing a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients.INTRODUCTIONWith the softening of the metals and minerals prices, and the escalated costs of building new processing plants, it is now economically more viable to improve and debottleneck the existing facilities, rather than build new ones. However, spending new money on old plants requires careful considerations, in order to identify the most economically advantageous incremental steps of improvement and the best potential returns on investment. Process modeling, hand in hand with plant measurements, can identify the best scenarios to balance the three aspects of plant capacity (nameplate, utilization and yield), both at the global and the individual system and subsystem levels."

Jan 1, 2016

By G. Ladouceur

"Northgate Patino Mines produces a copper concentrate assaying 22% Cu. Moisture content of the product averages 12.5% H20 when dewatering with conventional vacuum disk filters. Recent smelter contracts reflect higher energy costs and increased moisutre penalty charges. This situation forced Northgate to investigate possible alternatives such as rotary dryers and pressure filtration. After laboratory testing, it was found that pressure filtration could economically meet the smelter's requirements. Pilot plant testing was then undertaken and confirmed the laboratory test results. Based on these findings, a model I.S.F. 1500 x 28/22 I.R. Lasta filter press was purchased.This paper describes the Copper Rand dewatering flowsheet the operation of the press and the economics of the process.IntroductionNorthgate Patino Inc. operates 2 und erground copper mines and a 3300 ton per day concentrator located in Chibougamau, Quebec, some 425 miles north of Montreal and 300 miles northeast of Noranda, Quebec.Copper concentrate is produced at a rate of 250 tons per day and trucked to a C.N. siding 10 miles from the mill site and then railed to the Noranda Smelter.Until early 1981, moisture content of the concentrate at 12.5070 was acceptable since smelter penalty charges were relatively low ($0.10 per ton per unit over 10070 moisutre). In January 1981, a new contract was signed in which the penalty was raised to $1.10 per ton per unit over 8070 . This and the increasing truck and rail costs justified the change-over from vacuum to pressure filtration . The Lasta I.S .F. 1500 x 28/22 was then purchased and installed, and operation of the plant started in December 1981."

Jan 1, 1987

By K. M. Tait, M. M. McDonald

"An overview of the status of the development and application of Integrated Gasification Combined Cycle (IOCC) power generation is presented. Current projects in North America, Europe and Japan are described, together with the status of plans to apply the technology in Canada. A brief review of the technology is presented, including promising coproduction cycles and hybrid gasification fluid bed processes. The ability of the process to be modified for CO2 to be extracted for enhanced oil recovery or disposal is addressed. The environmental impact of IGCC technology is compared to those of other power generation technologies IntroductionDefinition and HistoryIntegrated Gasification Combined Cycle (IGCC) technology is a concept which has been around for about 50 years but has been generating increasing interest in the last 10 to 15 years. This paper focusses on coal as the feedstock for gasification. Other feedstocks used in gasification systems have included oil, biomass, tires and petroleum coke. IGCC technology integrates coal gasification with generation of electricity by means of a combined cycle system which fires the produced gas in the gas turbine. Figure 1 shows the basic components of an IGCC system which are the gasifier, the gas cleanup system and sulphur recovery plant, the gas turbine/generator set, the heat recovery steam generator (HRSG) and the steam turbine/generator set. The benefits of an IGCC system over a conventional Rankine Cycle pulverized coal (RCPC) fired system for the generation of electricity from coal are that the IGCC system has potential to have higher efficiency and lower emissions of NO., SO and CO2 per unit of power produced than the corresponding RCPC system."

Jan 1, 1994

By T. L. Carpenter

"The presence of excessive water in the Gibraltar East Stage 1 pit initiated studies into the ground-water conditions that might be expected in mining the Granite Lake and Pollyanna pits. Hydrologic information obtained from a pump test program in 1974 indicated that deep-well dewatering could be successfully achieved. In 1976, a deep-well dewatering system consisting of eight wells was installed on the periphery of the Pollyanna pit . it has been responsible for a significant decrease in mining costs.This paper presents a brief summary of the engineering principles involved in the design of the Gibraltar dewatering system and the problems encountered in the installation and operation of deep-well pumps. IntroductionGibraltar Mines is an open-pit copper-molybdenite mine located approximately 230 air miles north of Vancouver in the central interior of British Columbia (Fig. I). The property consists of three separate major orebodies; Gibraltar East, Granite Lake and Pollyanna (Fig. 2). Mining commenced during the summer of 1971, in the Gibraltar East Stage 1 pit. The Granite Lake Stage 1 pit was mined from mid 1974 to mid 1976. The Pollyanna Stage 1 pit is currently being mined and the Gibraltar East Stage 2 is being developed for production. This report is intended as an outline of the studies and tests leading up to and including the installation of the Pollyanna pit dewatering system, the problems encountered and the results obtained.GeneralIn the summer of 1973, mining in the Gibraltar East pit progressed below ""daylight"" on the down-hill side and ground water very quickly became a costly nuisance in the day-to-day mining operations. Mining, maintenance and blasting costs reflected these problems. Concern was also voiced about adverse effects of ground water on pit wall stability. This concern later became a reality in the Gibraltar East and Granite Lake pits. A study was initiated to investigate various methods and costs of dewatering the pit areas. The study included in-pit sumps, deep peripheral wells and a drainage gallery system located below the pits."

Jan 1, 1980