Search Documents

By Deborah McCombe

"and Bill Roscoe, Consulting Geologist and Principal with Scott Wilson Roscoe Postle AssociatesMineral property valuations are carried out for a variety of reasons, such as mergers and acquisitions, non-arm’s length transactions, initial public offerings of stocks, support of audited financial statements, fairness opinions, determination of vendor considerations, litigation, expropriation, income tax matters and insurance claims.The CIMVal Committee was formed in 1999 to review and advise on approaches to the valuation of mineral properties. CIMVal is a special committee of CIM formed on the recommendation of the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission.After solicitation of views and consultation with various interested parties, the CIMVal Draft Standards and Guidelines for Valuation of Mineral Properties were released for comment in February 2002 and were finalized in February 2003. CIMVal’s objective was for the standards to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges. To that end, the standards contain many of the definitions and concepts of National Instrument 43-101, Standards of Disclosure for Mineral Projects, which came into force in February 2001.The intent of the CIMVal Standards and Guidelines is that mineral property valuations be carried out by appropriately qualified individuals and that all relevant information be fully disclosed. It consists of two parts: standards, which are mandatory in the valuation of mineral properties, and guidelines, which elaborate on the standards and provide guidance and recommendations for the valuation process and for reporting."

Jan 1, 2003

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By Ramin ArameshAsl

Urumieh-Dokhtar is the well-known vast metallogenic belt extended from NW to SE of Iran and basically is referenced in copper mineralization studies in Iran. Hashtjin 1:100000 sheet (NW Iran) is located on this belt and rock units are consisted of Oligocene intrusive, volcanic rocks and Eocene Sedimentary rocks. Concerning the significance of identifying the alterations and faults zones in copper exploration, the aim of this study is identifying the copper mineralization by multi-spectral analysis of ASTER (Advanced Space borne, Thermal Emission and Reflection Radiometer) satellite images in the limitation SD-SWIR (Spectral Domain of Short Wave Infrared). Several analytical methods are implemented in this study such as SAM (Spectral Angle Mapper), MF (Matched Filtering) and PCA (Principal Components Analysis). These methods have been utilized for recognizing the Argillic, Propylitic and Sericitic alteration zones and all of them are relying on the remote sensing methods as well as geological studies of new targets for copper mineralization identification in the area.

Aug 1, 2013

By E. Hinton, L. Bloomquist

"This paper describes a guidance system for autonomous underground mining vehicles, which does not require any infrastructure or inertial positioning systems to aid the guidance process.BackgroundINCO Limited mines approximately ten million tons per annum through 12 operating mines in the Sudbury, Ontario, area (Fig. 1). With challenges from operating in a cyclical marketplace as well as new technologies making alternative nickel ores more competitive to refine, the Mines Research department embarked on a strategy that pointed toward automation as a tool to help the company become even more economical in mining.The mining industry has been looking for ways and means to mine orebodies more and more inexpensively. Automation and the lessons learned from manufacturing had a great influence in the direction of research at INCO Limited over the past ten years. Guidance systems have evolved over the years but the majority of commercially available systems rely on some form of infrastructure. This, in part, has caused some resistance from operators to install and maintain automated or semi-automated systems for guidance of underground machinery.Internal industrial studies cited travel time to and from the workplace as one of the major time sinks in the shift of underground miners. Depending on the mine, it may be as much as two hours moving in and out of an area. Some work areas have accommodated this by having “hot changes” at the work place. However, at some point in time, there are two people tasked with the same job and on site at the same time to make this overlap occur.Tele-operation of underground hard rock equipment eliminated this overlap and also provided a comfortable environment in which to work. By taking advantage of the communications network installed, the miners proved that they could operate three machines with relative ease. This was accomplished by a vision-based, “painted line,” autonomous guidance system termed the light rope system.With a few years’ experience with the system, some issues have arisen, including the cost of the rope itself (Fig. 2).The vehicle’s route is limited to the paths defined by the light rope, and a system of switching power to the light rope to select different routes is required. The rope itself is subject to damage from nearby blasts. Also, the system offers no obstacle detection; the vehicle may be switched off as a means of shutting the machine down thus protecting personnel in the area."

Jan 1, 2001

By K. M. Wild, C. D. Martin, F. Amann

Peak laboratory strength data obtained from low permeability clay shales/rocks often display a bilinear or non-linear failure envelope. In many of these tests pore pressures are not measured because of issues associated with back-saturation prior to confined compressive loading. In such tests the effective state of stress at failure remains unknown and provides room for speculation. The non-linear shape of the failure envelope may have several reasons including the influence of capillary forces or the tendency of a saturated clay shale to dilate as the confining stress is changed. The former stems from sample preservation, preparation or core unloading effects and represents a partly saturated state (i.e., not representative for the in-situ state); the latter represents the response of a saturated material. This contribution discusses these issues based on a data set obtained from Opalinus Clay specimens, and concludes that without a careful back-saturation processes knowledge of the underpinning reasons for the non-linear failure envelope cannot be obtained.

Jan 1, 2015

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By W. T. Gotheridge

The principal sources of coal-dust underground are, of course, coal, and the working of coal. Coal-dust is most dangerous when it is in the finest state of division. This class of dust is found mostly on the roads, being blown or shaken off the loaded trams in transit, or carried in suspension by air currents. The air current passing from the working faces may also carry dust in suspension into the return airway, and the air current from the surface may carry dust from the shakerscreens into the intake airways. The mosl dangerous dust we have to contend with is, (a) that which is most finely divided, and (b) that which contains the most volatile matter, including the inflammable occluded gases, and also oxygen absorbed from the air. According to experiments, coal-dust in a fine and dry state would intensify an explosion, in air free from fire-damp carrying in excess of 3 ozs. of fine dust or 6 ozs. of coarse dust per cubic yard. The volatile matter in the dust must be between 12 and 31 per cent. in the ash-free coal, the latter percentage giving the highest flame velocity. It is vary difficult to propagate flame where coal-dust contains a large percentage of stone-dust, (say 50 per cent.). Shale-dust or other incombustible dust containing no volatile hydro-carbons or carbonaceous matter will prevent the extension of an explosion if mixed with coal-dust in proportion of say 70 per cent., and if the dust is finely divided and dry.

Jan 1, 1924

By Al Gagnon

Since start-up in 1972, many circuit problems have been encountered, most of which were related to the abundance of fines (-28 mesh), which the circuit had not been designed to treat. The major problems associated with the original circuit included excessive loss of magnetite, reduced throughput during periods of a high proportion of fine coal in the plant feed and low yield in the fine coal circuit. This paper outlines the coal processing circuit at Fording Coal Limited as it exists today, with emphasis on the changes to the original fine coal treatment circuit.

Jan 1, 1978

By J. H. Schloen

"One of the most important phases in Canada's relatively rapid development of its metal mining and refining industries was launched in 1928 when the directors of Noranda Mines Limited decided to establish an electrolytic copper refinery ""somewhere in Eastern Canada”. Noranda's president, J.Y. Murdoch, had already evolved the company's ""mine to market"" policy and was determined to prove the economic feasibility of refining Noranda copper in Canada. The time appeared to be ripe as buoyant business conditions continued into 1929. In addition, proven ore reserves at the Horne Mine in northwest Quebec had virtually tripled and the price of copper had reached a healthy 15 cents per pound. Letters Patent incorporating the company bearing the date February 6, 1929 had been granted by the Secretary of State in accordance with an application that specified a capital structure of $2 million divided into 20 000 shares with a value of $100 each. Noranda assumed 70% of the original investment in the proposed refinery, while the Nicholas Copper Company of New York (which later became Phelps Dodge Corporation) and British Metal Corporation Ltd. of London, England, each were responsible for 15%. Nicholas Copper Company agreed to supply the design and to supervise the construction of the refinery and British Metal Corporation would act as sales agent and market the refinery's products."

Jan 1, 1999

By Yuki Koshino, Kenji Kaneko, Yasuhiro Aruga, Takuya Maeda

"In general, there is a strong correlation between dislocation characteristics and mechanical properties of aluminum alloys. In this study, dislocation characteristics of tensile deformed Al-Mg alloys were examined by transmission electron microscopy. An Increase in the solute concentration, ranging between 0.3 and 1.1%, Mg leads to increase in strength and decrease in uniform elongation. The accumulation of dislocations during the tensile deformation is observed in lower strain as the concentration of solute Mg in the alloy is higher. It is believed that the solute Mg in Al-Mg alloy promotes the accumulation of dislocation during the tensile deformation resulting in the decrease in elongation.INTRODUCTION The influences of the amount of Mg concentration on the tensile properties of Al-Mg alloys has been investigated by many researchers. It has been understood that the tensile ductility of Al-Mg alloy is higher for the Al-Mg alloys with higher Mg concentration beyond 2 mass% (Mukai, Higashi, Hirano & Tanimura, 1993). Uchida and Yoshida (1995) reported the formation of microbands during the tensile deformation due to the localization of dislocations, and the amount of microbands were reduced when the Mg concentration of the Al-Mg alloy was increased from 3 to 9 mass%. Their study suggested that the dynamic recovery of dislocation was retarded due to the increase of the Mg concentration during the tensile deformation, which resulted the increase in ductility. On the other hand, in the case of Al-Mg alloys with the Mg concentration less than 3 mass%, the reason why the ductility of Al-Mg alloys decreases with increasing Mg concentration has not been sufficiently investigated. In general, the Mg concentration used for automotive usage is less than 1 mass%, in the case of Al-Mg-Si alloys (Aoki, 2013). Therefore, to clarify the roles of Mg in the low concentration range on ductility of aluminum alloys and to elucidate its mechanism contribute to alloy design of Al-Mg-Si alloys having good formability."

Jan 1, 2018

By C. G. McLachlan

Professor H.E.T. Haultain: To me from time to time the urge comes to say the agreeable thing as well as the disagreeable in commenting on the work of others. It is a prerogative of age. I don't apologize. To myself I justify my action as based on a long experience of the matters with which I deal, and I like to tell myself that I have a certain responsibility in such matters on account of my detached position. This Noranda article is a very fine contribution concerning Canadian milling, and I am surprised that no word of commendation or thanks has appeared concerning it in the BULLETIN. There is altogether too much written in these days by men rushing into print, concerning laboratory work, that has not been tied into, nor has resulted in application in the field. The authors of this paper have not rushed into print. The preparation of this paper was evidently an uncongenial task. If the authors had been that way inclined, it could have spread over several lengthy papers. It is an important article because it represents an enormous amount of work in the laboratory and the mill, extending over a period of sixteen years, and resulting in fine metallurgical and economic results with a very difficult and involved problem. It is a fine article because it is so well prepared and presented. It deals with an unusual ore condition, but there is much in it of use to every cyanide millman. It leaves very little room for criticism, though there may be differences of opinion in regard to some of the chemistry phases with which I am not conversant. I am struck by the enormous amount of persistent, painstaking, conscientious research work involved, and in the careful, sincere way in which the methods and difficulties have been described. Persistence and sincerity are the key note of the effort. It should have a good educational effect on the rising generation of millmen, and it should continue for long as a work of reference, and a spur to others. There has been an important by-product, the training and development of the young men engaged in the work. Three of them became superintendents of important mills. One was sought for important work in Africa, another has joined a large research organization in the United States.

Jan 1, 1946

By J. Kouam

Al-Si-Cu and Al-Si-Mg alloys are widely used in several applications. Although they can be produced near-net-shapes, products made of these alloys very often require some machining. The purpose of this study is to evaluate the machinability of A319 and A356 under TO and T6 conditions. The machinability was assessed using during dry drilling machining process and the machinability indexes used are the chip form, the chip breakability and the cutting forces. It is found that 319 and 356 exhibit different machinability behaviors, especially in the T6-condition in terms of forces requirements, chip breakability and chip segmentation. It is also found that both the microstructure of the workpiece materials and the machining conditions significantly affect the chip formation mechanism, and therefore, the machining parameters could be selected to promote a chip form that is easily manageable in production.

Jan 1, 2011

By Y. Chunhua, L. Chunsheng, W. Sheng

"Countercurrent solvent extraction is the dominant industrial rare earth separation method. For the rare earth separation, with low separation factors and multiple components, designing and optimization plays an important role in reaching product quality and reducing separation plant costs. Based on the theory of countercurrent extraction, cost-efficient methods, such as third-outlet separation and hyperlinked extraction processing, have been introduced following computer simulation. The consumption and fixed investment of industrial practice are compared, by which advantages of the optimized rare earth separation process are indicated. INTRODUCTIONThe rare earths (RE) have outstanding optical, magnetic and electric properties in advanced material applications and have therefore received much international attention in recent years. Liquid-liquid extraction is the major industrial RE separation method and is widely used in the industry. Supported by the government and with collaboration from the institutions and enterprises, China has made great progress in RE separation, and has become the dominant supplier of separated RE products. Complicated by multiple elements and low separation factors, careful design of RE separation processes is vital for the quality and cost of production. The theory of separation is the key to basic of flowsheet design and industrial applications.BASIC SEPARATION PROCESS AND THEORYGeneral ProcessAcidic extractants such as P507, P204 and naphthenic acid, are the most popular extractants in modern RE separation industry. In the general separating process, the extractant is saponified with a base, then ion-exchanged with RE solutions, thereby to provide stable and high RE loading in the extractant to fulfill the requirement of production quantity and quality. The RE-loaded extractant is then countercurrently extracted and scrubbed with RE solutions and the RE element thereby is purified. After the countercurrent extraction process, the RE-loaded extractant is stripped with acid to obtain an aqueous RE product, and prepare the extractant for recycling (Xu, 1995)."

Jan 1, 2012

By E. G. Langille

"The Premier mine; owned by Silbak Premier Mines; Limited; is 14 miles from Stewart at the head of Portland canal. Development of the property began in 1918; and since chat time a very large amount of gold and silver as well as some lead and copper have been produced from the mine.The area in the vicinity of the mine is underlain by greenstones tuffs, and sediments of Mesozoic age, belonging to the Bear River formation of the Hazelton group. These rocks are intruded by a stock 2 miles in diameter, composed of orthoclase porphyry and called the Premier porphyry. It sends numerous sill-like and dyke-like tongues into the Bear River formation, and is intruded in turn by a granodiorite outlier of the Coast Range batholith. The orebodies occupy fractures and fracture or shear zones. Primary ore consists chiefly of pyrite, galena, and sphalerite, with some chalcopyrite. The upper 300 feet, or locally 600 feet, contained presumably secondary silver minerals."

Jan 1, 1954

By Roland Hunt

This paper deals with the practical problems as sociated with blasting a heated pillar remnant. This pillar remnant was the final stage in the blasting of a multi-stag e pillar blast. Production from the previous stages had produced burning sulphide ore, resulting in high rock temperatures in the final unblasted stage. This is an account of how, under difficult conditions, the pillar remnant was blasted.

Jan 1, 1977

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By Hector Monette

"AFTER SPENDING a lifetime in the mining industry it is normal that one should be concerned with the future of his profession, especially if he is directly responsible for the education and formation of future mining engineers. It is not necessary to insist on the importance of mining for Canada and for the entire world to prove the necessity of the Mining Engineer. A statement was made by Zay Jeffries, former vicepresident of General Electric Co., and here I quote: ""Even though minerals without man are of no moment, man would not be man as we know him without minerals ... ""minerals are as essential to the life of social man as food is to man himself"". This certainly expresses magnificently the purpose of the mining profession. These are the reasons why I have accepted to present my views on the future of the Mining Engineer. If I express some concern it is not because I feel that there is any danger for the profession to disappear; men will always respond to a challenge and this can be found in the extraction of minerals as well as in any other field of human endeavour. However, the first big question concerns the competitive position of Canada in the world of mining. To be made available to Canadians and to the rest of the world, all this tremendous potential mineral wealth that our country has been so generously endowed with by nature must be gained from the earth's crust at a competitive cost. Otherwise it will never become ore and will have no value. Let us not forget that although minerals are discovered, mines are not found but are made. So let us be more efficient mine makers. To accomplish this end, it is the duty of the different responsible organizations at all levels - be they governmental, para-governmental, public or private institutions - to do their utmost to assure the profitable development of our mineral wealth. The University has an all-important role to play in preparing all the specialists required by this intricate machine that mining is. All the different disciplines of engineering, health, social and -managerial sciences are needed for the good functioning of the mining industry. Although they are all essential, some will play a more important role as a member of the structure. In this discussion it is the role of the most important member, the mining engineer, who is actually responsible for the extraction of the minerals from the earth's crust that must be established. From this we will then be able to analyse his responsibilities and try to suggest the mining engineering program most suitable to prepare this engineer for his future role."

Jan 1, 1972

By Thomas Kilpatrick

The liability created by building this railway is the great financial problem before the people of British Columbia at the present time. In dealing with the subject, I propose to divide it into three periods: The Past - The Present - and The Future. The Past The primary objects in building the railway were to provide an independent and direct route for the Grand Trunk Pacific railway into the city of Vancouver, and to open the central and north-eastern portion of the province.. This vast territory, almost one-half the entire area of British Columbia, has great wealth in fruit, agricultural, and grazing lands; timber, coal, water-power and minerals of all kinds, including some of the richest placer deposits in the world. Rivers and lakes teem with fish. Big game, including moose, elk, caribou, deer, grizzly and black bear, mountain goat and sheep, is plentiful and there is an abundance of small game and fur-bearing animals. In addition, its scenic attractions are unsurpassed in Canada. To develop these resources it was considered necessary to build a railway from south to north as a main artery of transportation and, if necessary, branch lines to carry heavy .shipments of coal or other commodities. Lighter freight may be handled by motor trucks from distant points to the railway.

Jan 1, 1925