Search Documents

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By A. Atef

Vulnerability is a measure of the extent to which a community, structure, services or geographic area is likely to be damaged or disrupted by the impact of particular hazard. Current asset management practices focuses on studying factors that affect performance of isolated infrastructure networks and model a set of actions to control the expected performance of these networks. This approach ignores the underlying spatial and functional interdependencies among these infrastructure networks and their vulnerability. The purpose of this paper is to introduce a new method that recognizes the effect of spatial and functional interdependencies on vulnerability rating of water, sewer and road networks. The proposed method consists of: 1) risk assessment model, 2) interdependency assessment model and 3) vulnerability assessment model. The risk model is composed of two modules: 1) water and sewer risk module and 2) road infrastructure module. The water and sewer risk module will cluster these assets into three risk categories based on environmental, social, operational and economical factors. The road infrastructure module will cluster road assets into three risk categories by using rational factorial technique based on road type, serviceability index, traffic load, and freeze and thaw index. The interdependency model will deploy the risk ranking to perform geospatial analysis in ArcGIS which results in determining the interdependent layers of waters, sewers and roads. The vulnerability model will deploy fuzzy neural networks technique to determine the vulnerability rating based on spatial and functional interdependencies. The fuzzy neural networks are utilized to overcome the lack of historical data and incorporate experts? preferences for establishing the knowledge base for vulnerability assessment. The expected contribution of this framework is to aid decision makers in understanding the interdependencies between civil infrastructure assets and to which extent such interdependencies can compromise assets performance.

Aug 1, 2013

By H. S. Bostock

"The study of the geology of Mayo district began in 1900 with R. G. McConnell's exploration of Stewart river; and has been carried on intermittently for the Geological Survey of Canada by J. Keele; D. D. Cairnes; W. E. Cockfield; C. H. Stockwell; and the writer. It has revealed a thick group of schists; quartzites; and crystalline limestones; almost certainly Precambrian in age; placed in the Yukon group; and a group of younger intrusive igneous rocks varying in composition from granite to gabbro. These include bodies of many sizes and forms; from stocks 8 miles across to small dykes and sills.Prospecting in the district began about 1897 and has disclosed the presence of gold, silver, lead, tungsten, tin, zinc, antimony, copper, arsenic, manganese, and mercury, both in placer and lode deposits . Of these metals gold, silver, and tungsten have been produced from placer deposits, and silver, lead, and gold from lodes. This paper deals only with some structural relationships of the lode deposits, generally referred to as the silver-lead veins, which have yielded the greater part of the mineral production of the area. From 1938 to 1941 the geological mapping of the district for publication on a scale of 4 miles to 1 inch was carried out by the writer, and the ideas expressed here are based on this work. No comprehensive detailed study of the silver-lead veins has been made, but the mapping has brought to light several important facts. The rocks of the Yukon group, although of a striking sameness throughout their section, can be divided into a number of distinguishable members by means of which the main structures can be traced . The most important and readily distinguishable rock in the group is referred to here as the quartzite member. This is composed of quartzite and schist in about equal proportions. The quartzite is resistant to erosion and forms most of the outcrops of the'member and the peaks of the Gustavus mountains and mount Haldane (Lookout)."

Jan 1, 1954

By Jean-Yve Tremblay, Michel Prud'homme

"IntroductionIndustrial minerals include a group of more than fifty minerals which are marketed into almost all the sectors of industry; they are the backbone of many manufacturing industries. Table I shows major end-uses for industrial minerals in manufacturing sectors.At Energy, Mines and Resources, industrial minerals are divided in three major categories: (I) agro chemicals and chemicals, (2) construction mineral s, and (3) ceramics and specialty minerals. A listing of the major groups of minerals is shown in Table 2.Agro-chemicals and chemicals are sold on the basis of their chemical content and purity. Construction minerals or structural minerals are distinguished by their performance as low cost and bulky commodities. Ceramics and specialty minerals are performance-specific and are sold for their property on imparting functions on end-products. Industrial minerals have unique characteristics that are useful in many stages of processing; from crushed size to micronized fillers a single mineral ca n serve a broad range of industries because of its intrinsic properties.The Industrial Minerals Industry in CanadaCanada has a large industrial minerals base and is a world leader in the production of some of them. The total value of product ion of these minerals has grown by 115% over the last 10 years despite the misfortune of asbestos.Industrial minerals have shown remarkable growth in the past 20 years at an average annual rate of 9.2%, compared to 7.8% for metallic minerals. In 1986, the value of industrial minerals rose to $4.9 billion, or 14% share of the Canadian mineral production. Figure I shows the value of production of the mineral industry for the period 1966-1986.The leading segment in industrial minerals segment since 1976 is the chemicals and agro-chemicals sector which has an average annual growth rate of 5.75 % in terms of value of production. During the same period, the growth rate for the whole Canadian mining industry was 1.37% per annum. The chemicals and agro-chemical s sector increased its contribution to the total value of production of 2% to 6070 despite the growing share of fuel minerals with 59%."

Jan 1, 1988

By J. Lu, M. Mohammadi, C. Pelletier, B. Wassink

Chemical reduction of selenate by chromous ions is proposed as a novel method to remove selenate from sulfate-bearing solutions Chromous ions were generated by electrochemical reduction of chromic ions using an electrochemical cell. The investigation was conducted in sulfate medium and under various concentrations of chromous ions (0.0062 to 0.05M), pH 1 to 2.2 and temperature 10 to 60°C. Selenate ions were rapidly reduced by chromous ions to hydrogen selenide. The overall reaction at a chromous/selenate molar ratio of 8 or higher can be expressed by the following reaction. At an initial chromous/selenate molar ratio below 8, the products are hydrogen selenide and elemental selenium. At a lower chromous/selenate molar ratio and pH, more elemental selenium and less hydrogen selenide are produced. The reduction kinetics is controlled by both chromous ion and hydrogen ions concentrations. The reaction rate is first order with respect to selenate, hydrogen ion and chromous ion concentrations. It was found that the selenate reduction rate with chromous is independent of the concentration of sulfate present in the solution. The general rate equation was proposed and the rate constant was calculated as k= 0.38 M-2s-1. An activation energy of 58.7 kJ/mol was obtained in the temperature range from 10 to 50°C. Nearly 100% of selenate can be reduced to H2Se from solution containing 17 ppm selenate in less than 30 minutes at pH 2.2 and 60°C. Various strategies have been tested to remove the produced H2Se from solution. INTRODUCTION Selenium in nature is mostly associated with metal sulfide minerals such as copper, iron, zinc, and lead sulfides (Zingaro & Cooper, 1974). The extraction of metals from ores has the potential for selenium contamination of ground and surface water which can pose an environmental and health concern. Therefore, selenium contamination in the receiving environment is a key issue for many industries (specifically copper industry) and the treatment of wastewater contaminated with selenium is a growing challenge. The effective removal of selenium from contaminated water is very important to support sustainability in the copper industry and the other industries with selenium pollution issues.

Jan 1, 2019

By K. Iturralde

The article discusses the possibility of automation in refurbishment processes of social dwelling built from 1950 to 1970. These massively produced buildings were mostly designed prior to the law enforcement regarding thermal insulation or accessibility. Nowadays, many of these buildings are being retrofitted. The article focuses on the works in the external envelope. The task of renewing the whole social building stock is big and it requires a systematic process that facilitates a rapid upgrading, without neglecting the specific situation of each case. How could an automatic refurbishment process of these buildings be defined? The process should start with the data collection of the building and the creation of a 3D model using software such as BIM. The project, drafted in 3D, should facilitate the manufacture of building elements by robotics. In turn, it should be noted that during the assembly at the site, the pieces must be fixed quickly and efficiently. Is it possible to implement an automated process for the refurbishment of apartments built in the second half of the twentieth century? To approach the answer, a virtual refurbishment project is performed. The article focuses on the rehabilitation of the building envelope. Furthermore, it gives special attention to the double skin facade. It is well known that a second skin in this type of building can be an element that integrates several functions. Finally, needless to say that refurbishment of residential buildings is a need in our society. By extending its life cycle, robotic refurbishment provides more favorable socioeconomic and environmental capabilities than the sole construction of new buildings.

Aug 1, 2013

By Leopoldo Gutierrez, Sergio Castro, Lina M. Uribe, Janusz S. Laskowski

"The effect of sulfite and metabisulfite ions on the amyl xanthate flotation of copper-activated pyrite, in distilled water and seawater, has been studied by micro-flotation tests and redox potential measurements. The activation of pyrite was carried out varying copper ions concentration. It was found that in the presence of copper ions in solution, sulfite and metabisulfite are able to depress copper-activated pyrite at neutral or slightly acid pH. After the addition of sulfite or metabisulfite ions the resulting pH is more acidic with metabisulfite ions. A significant increase of the redox potential of the solution was observed as copper ions concentration increased. Then, the initial reducing conditions brought about by sulfite and metabisulfite ions, change abruptly to oxidizing conditions in the presence of copper ions. Under these oxidizing conditions, the metabisulfite showed to be an effective depressant for pyrite mainly in seawater. However, sulfite was a pyrite depressant in both distilled water and seawater. Based on these results, the pyrite depression by sulfoxy-depressants during the flotation of Cu/Mo ores in distilled water and seawater is discussed.INTRODUCTIONDepression of pyrite by sulfoxy-depressants (sulfite and metabisulfite) in the presence of copper ions is an important issue. This is particularly true when pyrite depression in the flotation of Cu/Mo sulfide ores is carried out in seawater. The use of lime in seawater must be avoided because the formation of magnesium hydroxy-complexes and precipitating magnesium hydroxide strongly depresses molybdenite flotation (Castro et al., 2014). In order to solve this problem, one large plant in Chile uses sodium metabisulfite (MBS) instead of lime to depress pyrite in seawater. In plant practice, this also improves molybdenite flotation since with the use of MBS the pyrite depression is carried out at pH 6-7, instead the pH 11-12 usually employed with lime.From a general point of view, pyrite exhibits some natural floatability over acidic pH ranges and may be partially floated without thiol collectors (a coating of sulfur/polysulfides has been claimed). Therefore, pyrite flotation with xanthates is usually high in the acidic pH region, but decreases greatly at alkaline pH (Leppinen, 1990; Fornasiero and Ralston, 1992; Zhang et al., 1997)."

Jan 1, 2016

By H. Sakurai, M. Kato, F. Tanaka

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. The conditions in the CL- furnace change its settling efficiency, resulting in high variability of copper losses in slag. Modifications of the operation and maintenance procedures for the CL-furnace have significantly and sustainably reduced the copper losses in Gresik smelter to below 0.7%. A series of flow patterns evaluation in the CL-furnace demonstrated how the chemical reactions and settling conditions of the CL-furnace has been improved by the new operating procedures. Settling mechanisms for the matte droplets in the CL-furnace is also discussed using image analysis of solidified slag. INTRODUCTION The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. Since the top-blowing in the S- furnace agitates the molten bath strongly, matte droplets are dispersed over the slag phase when melts flow out of the S-furnace. Thus, the CL-furnace has an important role to settle and recover matte droplets efficiently. Since many papers have ascribed major part of copper losses to matte droplets suspended in slag (Tanaka 2007; Genevski et al., 2008; Starodub et al., 2016), flow patterns of slag in the CL-furnace can affect greatly on the profitability of smelters which have adopted the Mitsubishi process. PROCESS DESCRIPTION Figure 1 illustrates the Mitsubishi process schematically. The Mitsubishi process is the only system for continuous production of blister copper from copper concentrates and consists of 3 furnaces connected by enclosed launders those ensure the minimum emission of fugitives. In a smelting furnace (S-furnace) copper concentrates are fed with flux, oxygen-enriched air to form a mixture of slag and matte which cascades down to a slag-cleaning furnace (CL-furnace). The CL-furnace settle matte droplets in the mixture on the crucible from which matte is siphoned to a converting furnace (C-furnace), while discharging the cleaned slag (CL-slag). The C-furnace converts matte to blister copper by the top-blowing of oxygen- enriched air.

Jan 1, 2019

By W. L. Brown

"The properties of Base Metal Mining Corporation are in Yoho Park about 2 1/2 miles northeast of Field; British Columbia; on the main line of the Canadian Pacific railway. There are actually two mines; the Monarch on mount Stephen and the Kicking Horse on mount Field; separated by the steep valley of Kicking Horse river. The outcrops of the orebodies range from 4; 900 feet to 5; 300 feet above sea-level. The concentrator is situated below the Monarch mine and is connected to the main portal by an aerial tramway. The ore from the Kicking Horse mine is conveyed by aerial tramway to a storage bin on the main highway and is then trucked to the concentrator.During the construction of the Canadian Pacific railway through Kicking Horse valley, galena float was found at the base of mount Stephen. The East Monarch outcrop was staked in 1894. The outcrop of the West Monarch ore body on the cliff face of mount Stephen was not discovered until 1916. The Kicking Horse orebodies on mount Field were discovered a few years later. In 1912, a 75-ton concentrator was erected, which operated at intervals until 1924. During this period approximately 42,000 tons were mined and milled, largely from the East Monarch orebody. In 1928, the Base Metal Mining Corporation, Limited, was formed to take over the Monarch and Kicking Horse mines. A 300-ton differential flotation concentrator was erected and production started in the autumn of 1929. In a very short time, however, the low price of metals forced the mill to shut down until August 1933. From 1929 to 1935, when the mill again ceased operation, a total of 256,500 dry tons of ore, averaging 1.59 oz. silver per ton, 9.7 per cent lead, and 12.6 per cent zinc, was mined and milled, largely from the West Monarch orebody. After a period of further underground development, the concentrator reopened in 1940 and is still in operation. From 1940 to the end of 1944, 354,363 tons of ore was milled, averaging 5.32 per cent lead and 10.47 per cent zinc."

Jan 1, 1954

By N. Molaei, E. R. Bobicki

The continued demand for mineral products, coupled with the depletion of high-grade ore resources, has led to the mining of lower grade ores, which often require fine grinding to achieve mineral liberation. Regrinding of low-grade ores results in the production of fine gangue mineral solids and produces vast quantities of fluid fine tailings which are difficult to separate from water, particularly if they are composed of clay minerals. Organic synthetic polymers and inorganic salts have been widely applied in flocculation of colloidal suspensions in the treatment of mining tailings. However, there are growing concerns regarding their impact on the environment and human health. Recently, extracellular biopolymer flocculants or bioflocculants have attracted much attention as alternative reagents. In this study, much effort has been devoted to considering the effectiveness of protein and polysaccharide-based biopolymers for the dewatering of clay slurries. The interaction between kaolinite and illite clays and biopolymers was investigated via settling tests at pH 7 and 10. Zeta potential measurements were also conducted as a complementary technique. Results showed that protamine and lysozyme protein- based biopolymers were generally the more effective bioflocculants. Pectin, a polysaccharide-based biopolymer, showed a dispersing effect and has the potential to be used as a dispersant and/or depressant for clay minerals in froth flotation. INTRODUCTION With the depletion of high-grade ore resources, the need for mining of low-grade ores has increased over the past few decades (Bourgès-Gastaud, Stoltz, Dolez, Blond, & Touze-Foltz, 2014; Chen, Walshe, Fru, Ciborowski, & Weisener, 2013; C. Wang, Harbottle, Liu, & Xu, 2014). Low-grade ores often require fine grinding and contain clay minerals, leading to the generation of fluid fine tailings (FFT). It is a challenging process to separate suspended clay particles from water (Craciun, Manaila, & Stelescu, 2013; Dompierre, Lindsay, Cruz-Hernández, & Halferdahl, 2016; Kasperski & Mikula, 2011; Mercier et al., 2012). Clay minerals form stable dispersions in water due to their anisotropic nature, non-spherical morphology and colloidal size (Lagaly & Ziesmer, 2003; Olphen, 1977). The difficulty in separating clay minerals from water has led to the accumulation of vast quantities of FFT in oil sands, phosphate, copper and nickel operations, representing a huge liability for mining companies (Chen et al., 2013; Mercier et al., 2012)

Jan 1, 2019

By P. Molera

"In Catalonia, between the 10th century and 1878, some installations were developed which at first were called ""factories"" and later ""fargas"", since they manufactured iron and steel of low carbon content. Because of its excellent quality, the fame of this metal spread from Catalonia to many countries. Fargas were started in Corsica, the Low Countries, Germany, Oriental India, Madagascar, Finland and along the rivers Orinoco and Mississippi among others. The extractive process used in these fargas has passed into history as the ""Catalan Farga Process"", ""Catalan Process"", or just ""Farga Catalana"". With this technology, raw material was obtained for the fabrication of tools, nails, weapons, grilles, etc. to supply the national and export markets. Aside from meteorites and native iron, found as metallic nodules in basalts in Greenland and Palestine, the ancient civilizations, which had no means to reach the fusion temperature of iron (1535°C), obtained iron by a direct process. Similar processes were used until quite recently (1930s) by certain tribes in Central Africa; holes in the ground were filled with iron ore and coal, and combustion encouraged by blowing air by mouth or with bellows made of animal skins. Thus without melting the iron it is possible to reduce the mineral and obtain a porous and impure metallic mass, which is purified on forging by mechanical squeezing. With a process very likely similar, the famous column at Dehli weighing 6.4 m.t. was built about 300 B.C."

Jan 1, 1999

By Z. Zhang, D. Bouchard, H. Blanchette, A. Lemieux

This paper describes quality control methodologies for the production of semisolid A356 aluminum slugs with the SEED process. A methodology based on destructive tests carried out with an apparatus measuring the force to slice the slugs is presented. The force measurements were correlated with the solid phase morphologies of the slugs and were validated against a non destructive methodology that consisted in monitoring the temperature evolution of crucibles to produce the slugs and the drained metal. Results from the destructive and non destructive methodologies are compared and discussed.

Jan 1, 2006

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

By E. L. Horner

"Srnoky River Coal is capable ofprocessing 3 million tonnes per year ofrun-of-mine coal at the Smoky River Coal preparation facilities to produce 2.1 million tonnes of high quality, low volatile coking coal for export markets. Multi-seam surface and underground mining operations are scheduled to maintain raw coal feed to the plant. Two beneficiating circuits wash the coal. A heavy medium cyclone circuit cleans the plus 0.5 mm coal and a froth flotation circuit cleans the minus 0.5 mm coal. Clean coal is thermally dried, loaded into unit trains, treated for dust suppression, and transported to west coast port facilitiesf or export. Plant by-products are used as thermal fuel Jn an adjacent power station. Quality control procedures ensure efficient resource recovery for a yield of uniform specification product, at a 7% ash level. Introduction Smoky River Coal operates surface and underground mines in the Smoky River coalfield. Approximately 3 million tonnes per year (mt/ a) of run-of-mine (ROM) coal can be processed at the coal preparation plant to provide 2.1 mt/ a of clean, high quality, low volatile bituminous coking coal. Coal is processed by heavy media and froth flotation cleaning circuits and is thermally dried.Raw Coal Characteristics The characteristics of the ROM coal, both in terms of quality and size consistency, vary with intrinsic seam qualities and mining methods employed. The two seams mined (No. 4 and No. 10) show distinctly different washability characteristics. Seam No. 4 contains relatively few middlings and can be readily cleaned by dense-medium cyclones and froth flotation to give a clean coal at specification ash content. Seam No. JO is more difficult to wash, and the ash content of the clean coal is higher than No. 4 seam at the same operating conditions. However, when the upper I m is excluded from the plant feed, the remaining lower section has washability characteristics similar to No. 4 seam. Coal mined by underground means sometimes contains caprock and consequently tends to be dirtier than similar coal mined by surface means."

Jan 1, 1985

By L. Wolofsky

"The Candego property is in Boisbuisson and Christie Townships, Quebec, about 13 miles south of Marsoui, a village on the north coast of the Gaspe peninsula, 80 miles east of the railhead at Matane. It was the first producing mine in the peninsula. Production to October 1954, when operations were suspended, totalled 68,497 tons of ore, which yielded concentrates containing 8,706,535 lb. lead, 5,870,272 lb. zinc, 355,526 oz. silver, and about 1,000 oz. gold. The property was acquired by the present company in the summer of 1955.The mine has been developed by seven adits, driven into the west slope of the valley of the Marsoui River. The river here is at an elevation of about 1,600 feet, and is roughly 1,500 feet below the level of the adjacent upland. Adit elevations range from 1,760 to 2,330 feet. Five of them are in one vertical zone, on what was originally believed to be a single vein. Past production has come from Nos. l to 5; the chief present high-grade ore reserves are in No. 7.The author's observations were made in adits Nos. 3 to 6, in several of the old pits, in the surface trenches, and on drill core, at various times between December 1952 and September 1953. Much of the surrounding area has been mapped by Jones (I) and McGerrigle (2) for the Quebec Department of Mines. H. M. Kingsbury served as consulting geologist to the mining company for several years.General GeologyThe Candego veins occur in Lower ( ?) Ordovician sedimentary rocks which form a strip about 15 miles wide along the north coast of the Gaspé peninsula. The series includes limestones, shales, and sandstones, mildly metamorphosed in places. Three miles south of the mine is the north contact of the granitic intrusive, regarded as Lower or Middle Devonian, which underlies the Tabletop Mountains area. This batholith is about 10 miles long, in a north-south direction, and about 4 miles wide. At Mount Albert, about 5 miles west of the Tabletop intrusion, is a group of basic rocks, amphibolites and serpentinized peridotites, thought to have been intruded at the close of the Ordovician."

Jan 1, 1949

By L Mariani, G. Mendoza-Suarez

In this investigation, TiH2 powders were coated with copper and nickel by electroless plating to delay hydrogen evolution. Copper-coated samples were found to have a mixed acicular (2D growth) and cauliflower (3D growth) morphology whereas the nickel-coated samples had a cauliflower morphology. Examinations of the coated powder cross-sections revealed that the coating thickness ranges from 0.2 µm to 4 µm. Uncoated areas on the powder surface and coating flakes unattached to TiH2 particles suggest poor adhesion between the coating and the substrate. The phase transformation undergone by the TiH2 during dehydrogenation was studied in samples taken at intermediary points in the heating cycles and examined by XRD. The findings reveal that as the powder is heated from room temperature to 800°C, it changes from TiH1.971 to Tiu and to aTi. Differential Thermal Analysis (DTA) was performed to study the effects of the coatings on the temperature of hydrogen release. It was found that increasing the number of plating iterations, and therefore the thickness of the coating, creates a significant shift in the temperature of gas release.

Jan 1, 2006

By L. Jiang

The evolution of twinning in an AM30 Mg alloy was examined by uniaxial tension and compression testing at temperatures from ambient to 250°C and a strain rate of 0.1/s. The samples were cut along the extrusion direction from extruded AM30 Mg alloy tubes. Specimens deformed to various strain levels were examined by optical microscopy and electron backscattered diffraction (EBSD) techniques. The results indicate that the initial extrusion texture plays an important role in the formation of different types of twins and that the twinning behavior also depends on the strain path. Contraction and double twinning are the dominant twinning mechanisms in uniaxial tension, while extension twinning prevails in uniaxial compression. The different twinning behaviors are shown to be responsible for the sharply contrasting strain hardening characteristics of the experimental flow curves.

Jan 1, 2006

By A. Gakwaya, P. Vachon-Joannette, P. Gagnon, J. Lévesque

"Predictive numerical methods are essential tools for reduced development cost and improved high performance designs of modern aircrafts. Their use leads to savings in terms of design cycle time and experimental trials. Composite materials subjected to impact loadings demonstrate various damage modes such as matrix cracking, fiber breakage, delamination and, ultimately, fabric fracture. Composite laminates are extensively used in the aerospace industry, and their damage modeling is complex due to their inhomogeneity and anisotropic behavior. Damage evolution affects both in-service properties and performance of these composites. In this work, the drop-weight impact test has been simulated. Using a material model that accounts for both delamination and intralaminar damage, laminates response is analysed using numerical simulations based on 3-D finite-element models of the commercial code Abaqus/Explicit. Experimental and simulation results are compared, in terms of energy absorption and contact force. The obtained numerical results show good agreement with experimental data.INTRODUCTIONAs primary aircraft structures are increasingly being made from advanced fiber-reinforced polymer matrix composites and are in general exposed to a variety of impact scenarios (bird, hail, debris etc.), an understanding of the impact event and the performance of composite materials during impact is important in the development of new structures. This work is focussed on low velocity impacts that typically occur when foreign objects hit the aircraft during maintenance or other on-the-ground operations. These impacts can cause non visible damage that affect the structural integrity of the composite components. While for metallic structures, damaging impact events typically leave noticeable dents due to plastic deformation, in contrast, for high strength carbon fiber reinforced composites, they can deform elastically to strain levels exceeding 1% and the internal damage can often occur without the formation of a visible dent. The identification and effect of impact damage on the performance of the structure is thus of great concern to the aircraft industry as the durability and damage tolerance of these composite structures are strongly influenced by the size of detectable internal damage."

Jan 1, 2016

By O. Moselhi

Material can be seen as the fuel needed to execute the project from inception to completion. Material installed provides good indicators of progress achieved onsite vis-a-vis project schedule performance. It correlates well with the role of the schedule performance index (SPI) of the earned value method (EVM). Material is recognized to have a significant impact on achieved progress for physical completion of project activities. This paper presents a study on the development of material status index (MSI) in support of the EVM. Unlike the SPI, the newly developed index account for the criticality of project activities. This is carried out considering the total float of each activity, percent float (i.e. the ratio of float to activity duration) and the total float of the path on which the activity is located. MSI, can independently and jointly with SPI provide root causes behind problems encountered during project execution. In turn MSI can reveal material related factors behind the performance detected by joint interpretation of the two indices. MSI serves to provide added value in alerting management to take corrective actions. While SPI and MSI may have different values, they can jointly augment and enrich the captured project status based on EVM. To demonstrate the capabilities of the developed MSI method, it is implemented on a case study. The case encompasses the construction schedule of a hydro power station constructed in northern Quebec. Different scenarios are adapted from the real case to demonstrate a set of practical aspects of the developed index. The results generated from the analysis of the case study illustrate the useful features of MSI beyond those of the traditional SPI on two fronts; causation and the considerations of criticalities of actives.

Aug 1, 2013

By S. Mamonov, V. ?shikhin

"The purpose of work was the significant increase of copper recovery from slag at a concentrating plant. Analysis of study of slag phase composition showed the perspective of a slow slag cooling method due to its recrystallization and transition of primary copper minerals to secondary.Copper content in base slag varied between 0.71 and 0.96%. The study of a degree of copper minerals release of the slowly cooled slag in comparison with a yielding slag showed that in a flotation size grade –0.071 mm of yielding slag the weight ratio of released copper minerals grains is 58.95% against 86.73% in samples of slowly cooled slag. The process flotation sheet consists of three main, one control and two cleaner flotation operations with aftergrinding of middling products. A reagent mode was differed from a factory one by decreasing the slurry pH from 11–12 to 8–9. This paper shows research results of the slurry alkalinity impact on technological indexes of beneficiation (flotation).Industrial testing of a resulted batch of slowly cooled slag at “SUMZ” concentrating plant showed the efficiency of such processing: copper recovery to a copper concentrate increased by 15–19%.INTRODUCTIONIntensive development of mining and metallurgy industries within a 250-year period in the Ural region led to forming of approximately 315 man-made mineral formations at the territory of the Sverdlovsk region. The region contain over 32.5 billion tons of barren rocks and out of balance ores, over 1.5 billion tons of tailings, over 115 million tons of slimes, and over 100 million tons of metallurgical slag (Demin et al., 2000). Latters, at average, contain 407 thousand tons of copper, 2519 thousand tons of zinc, 7 tons of gold, and 150 tons of silver (Rudoy et al., 2011). Wastes generated in mining processing and metallurgical sector of economy contain not only thousands tons of copper and zinc, but cause significant damage to the environment where they are located. The reduction of negative impact of anthropogenic wastes on the environment as well as the storage volume reduction of valuable metals from dump slags is possible by improving the efficiency of the melting and further flotation of slags formed during this process."

Jan 1, 2016