Search Documents

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By S. H. Castro

Molybdenite depression by shear degraded polyacrylamide solutions has been investigated. Aqueous solutions of polyacrylamide-type flocculants were subjected to shear degradation under a range of high-speed stirring conditions. Settling tests, carried out with quartz slurries and sheared polyacrylamides, showed reduced flocculant performance with increased degradation. As the sedimentation rate is strongly dependent on the polymer's molecular weight, these results fit well with the shear degradation theory, which predicts the production of shorter chain segments due to breakage of the polymer macromolecules. Microflotation tests on natural molybdenite showed that the depressing ability of a commercial polyacrylamide flocculant remained unaltered after shear degradation, even when the flocculating ability was entirely lost. Practical implications of shear degradation on molybdenite flotation are discussed.

Jan 1, 2004

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

By Jae-Chun Lee, Sadia Ilyas

We investigate the technical feasibility of bioleaching of metals from low grade sulphidic ore. Experiments were conducted with an adapted consortium of Sulfobacillus thermosulfidooxidans and Thermoplasm acidophilum in batch bioreactors (1.5 L), small columns (10 kg ore load, 8 % S0 sludge) and large columns (80 kg ore load, 12 % S0 sludge). Approximately 83 % Ni, 85 % Cu, 55 % Fe and 81 % Zn was leached out in batch mode while 93 % Ni, 89 % Zn, 81 % Cu and 65 % Fe was leached out in column reactors. Bioleaching potential improved by acid pre-leaching, adaptation of microbial consortium and periodic bleeding of effluents.

Jan 1, 2014

Thermal barrier coating (TBC) systems provide thermal insulation to high temperature for aero¬propulsion. A fracture mechanical model developed earlier for multilayer systems is applied on TBC to realize superior performance by enhancement of fracture resistance. Functionally gradient materials (FGM) solution concept is the basis of approach followed here. A few realistic FGM TBCs are considered in the analysis in addition to a conventional TBC as the base case and a hypothetical worst case with YSZ-YSZ interface. Parameters like number, composition and thickness of graded layers and elastic modulus are considered for the analysis and quantitative improvement of fracture resistance of TBCs. The analysis is confined to deep crack with crack size to width ratio as 0.5.

Jan 1, 2010

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By J. Shanks

In 1920 the writer presented some notes, embodying his experience with storage-battery locomotives as main under-ground haulage-motors at Brazeau collieries. (1) Since that date these motors have stood up well to the test of maximum output and heavy overloads, having accomplished all that was expected of them. The notes presented in 1920 gave a brief description of the conditions under which these motors were working at Brazeau collieries, also the cost, per ton mile, of operating them. The cost per ton mile has since then been appreciably reduced, by working the locomotives nearly to capacity and under more ideal haulage conditions, on both shifts. It is not the intention of the writer to repeat what was written in 1920, but rather to give members the benefit of his experience in operating different types or designs of locomotives; to draw their attention to the drawbacks of some designs, and to the improvements made in some of the more recent storage-battery locomotives put on the market, as regards efficiency, upkeep, and safety. Because of their flexibility storage-battery locomotives have advantages over any other type of haulage, where grades are suitable to their use. The number in use in the mines in the United States has increased enormously during the past few years, and this method of haulage is, at the present time, attracting the attention of British and Continental mining engineers.

Jan 1, 1924

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By Charles Camsell

THE Northwest Territories covers a very large area-more than one-third of all Canada-and its most northern point, Cape Columbia in Ellesmere island, is distant only 500 miles from the Pole. Our first knowledge of the Arctic Archipelago, of which Ellesmere island forms a part, resulted from a gold-mining venture in Queen Elizabeth's reign. The English navigators of that time were eager to find a north-westerly and shorter and Jess hazardous route to the riches of China and Japan than that which Magellan had discovered, but they were unaware that the continent then known to bar a direct route extended in great width far to the north. Frobisher was one of these navigators. He reached in 1576 the bay in Baffin island now named after him, convinced that he had found a passage connecting the Atlantic with Asiatic seas. Forced to re-turn after ordeals in which ice, wind, and Eskimos flayed formidable parts, he brought back, among other novelties, a piece o black stone which had been picked up casually by one of his officers, and gave a little of it to the wife of one of the venturers, or financial backers of the enterprise. To quote now from Hakluyt: ? 'She by chance threw and burned it in the fire so long that , at length being taken forth and quenched in a little vinegar, it glistered with a bright marquesset of gold. Whereupon the matter being called in sorne question, it was brought to certain goldminers in London to make assay thereof, who indeed found it to hold gold and that very richly for the quantity." On the strength of this, the venturers, anticipating much profit, launched a second expedition to secure more of this stone, and 143 persons, including 14 miners and finers, set forth in 1577 and returned the same year, with, however, 200 tons of another mineral. Influenced by glowing accounts of veritable mountains of this mineral and by assays made after "additaments"-that is how "salting" in those days was described-the venturers, including Elizabeth, supplied funds for erecting a smelter and refinery at Dartford and outfitting a stilllarger expedition. And so, in 1578, fifteen ships departed with the Queen's blessing, for the same remote shores. After many mishaps, they returned with over 1,000 tons of the mineral, but when it yielded very little of value at the works in Dartford, the? Company of Venturers was forced into liquidation. Though our first prospector and miner was rather inconsiderate of the investors, he proved the existence of an archipelago, hitherto unknown, and secured much information about the new land and its dwellers.

Jan 1, 1938

By H. Fujiwara, T. Ito, T. Mizuguchi, K. Kawasaki

"In this study, we characterize the high-temperature deformation of typical “Class I” solid solution Al-Mg alloys as a superplastic elongation attributable to the solute drag creep of dislocations. The second-phase particles formed by adding Fe or Si as impurity atoms to the Al-Mg alloys impeded the gliding motion of dislocations, thereby decreasing their hot ductility and resulting in cavity formation. High-temperature tensile tests were performed with initial strain rates in the range of 1×10–3 to 1×10–1 s–1 at air temperatures 673–723 K. The dominant high-temperature deformation mechanism in these alloys was the solute drag creep controlled by the interdiffusion of Mg in Al. In this study, the calculation of critical length, defined by the diffusion-based relaxation of the stress concentration region around second-phase particles, is reported using the Needleman–Rice parameter. An analysis of the impact of cavity formation based on a comparison of the Needleman–Rice parameter and second-phase particle size is also reported.INTRODUCTION Aluminum alloys with high specific strengths are utilized as structural materials for transportation machines to minimize their weight, which consequently maximizes fuel efficiency, environment preservation, and so on (Miller et al., 2000; Heinz et al., 2000; Starke & Staley, 1996; Polmear, 1996; Immarigeon et al., 1995; Burger, Gupta, Jeffrey, & Lloyd, 1995; Ye, 2003). Microstructure refinement by severe plastic deformation (SPD) has been performed on a laboratory scale to achieve a higher strength of crystalline materials (Valiev et al., 2006; Song, Ponge, Raabe, Speer, & Matlock, 2006; Beyerlein & Toth, 2009; Sabirov, Murashkin, & Valiev, 2013; Sauvage, Wilde, Divinski, Horita, & Valiev, 2012). At room temperature, grain refinement strengthens the material, as given by the Hall-Petch relationship (Hall, 1951; Petch, 1953); at higher temperatures, superplasticity can be expected (Sherby & Wadsworth, 1989; Edington, Melton, & Cutler, 1979; Furukawa, Horita, Nemoto, & Langdon, 2001; Langdon, 2006). However, the synthesis of large-size materials by SPD processes is not yet feasible."

Jan 1, 2018

By J. F. Vynne

ABSTRACT This paper examines several of the systems and processes that have been developed over the past few years and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline rated suspended loads (RSLs) and inspection and response strategies. The use of these technologies provides significant increases in dragline production and reduces maintenance costs, downtime and the chance of a catastrophic failure.

Jan 1, 2010

By Free. Michael L.

Crushing ore prior to heap leaching enhances mineral liberation and creates fine particles that may require agglomeration to avoid permeability problems during leaching. Conventional modeling is relatively successful in describing general fluid flow and extraction in heaps. However, most models do not adequately account for the effects of mineral liberation and exposure or the effects of agglomeration, curing, and loading on heap leach performance. This paper will discuss methods to account for mineral liberation and exposure as a function of comminution. It will also discuss methods for incorporating liberation, exposure, and mineral locking as well as curing and fluid flow in heap leach modeling. It will also provide information regarding agglomeration and the effect of loading in heap leach modeling.

Jan 1, 2014

By M. Kellner

Due to continuously growing resource demands and increasing requirements for sustainability, safety and environmental protection on the other hand, the mining industry is being subjected to these additional requirements. Over the past few decades progress has been made in all topics. In 1987, the United Nations published the following in the Brundtland Report: ?development that meets the needs of the present without compromising the ability of future generations to meet their own needs.?[5] The term ?Blue Mining? means to work sustainably, economically, ecologically, and efficiently while also improving ergonomics, for example by increasing automation. An example of how mining can actively be involved in energy management will be shown. Initial evaluations of underground cavitites were done for purpose of energy storage. The planning and construction of underground pump storage plants both in active and inactive mining operations was also investigated.

Aug 1, 2013

By G. C. Bateman

THE cause of silicosis and its prevention have held the attention of medical men and mine operators for many years and at the present rime the study of this disease is more than ever to the fore, even though a considerable abatement in the incidence of silicosis has been noted of late. This abatement is due to individual and collective efforts. The Industry is keenly alive to the situation and much research is being carried on. Silica dust is assumed to be a contributing factor in the cause of silicosis. How it acts progressively in the early silicoric is nor fully understood. As the study advances, more effective measures of control may be evolved. At present the Industry has three known methods of reducing the incidence: 1. By thorough X-ray examination of all applicants, with special reference to chest conditions. Those who are considered to be susceptible to the disease are prevented from entering the industry. 2. Thorough ventilation of the mine. 3. Control of tuberculosis in mining centres and removal of miners when first symptoms of tuberculosis become apparent. In 1934, the Ontario Mining Association formed a Committee, known as the Technical Silicosis Research Committee, to study and supervise work on problems related to silicosis. This Committee obtained the full-rime services of a mining engineer to carry our research work at the mines in the Province of Ontario. The Ontario Mining Association has also provided funds for the purpose of carrying on research work along pathological and biological lines. This work is being done in the Department of Medical Research of the University of Toronto, in the Banting Institute, under the supervision of Sir Frederick Banting. The Silicosis Committee work in full cooperation with the doctors in the Banting Institute and provide material from the mines for the it use.

Jan 1, 1936

By M. Romana

"RMR geomechanics classification is being used all over the World as a useful tool for tunnel predesign and construction. Bieniawski (1989) provided guidelines for tunnel excavation and support, according RMR numerical values; guidelines which are now included in almost all tunnelling books, regulations, and Internet portals. But in the last 25 years tunnelling techniques have changed and some of the guidelines have become obsolete.. The conditions of tunnels for the 1989 guidelines application were: horseshoe shape; 10 m width; vertical stress < 25MPa; construction by drilling and blasting. Actually a substantial number of tunnels are mechanically excavated. The tunnel themselves are now bigger: a span of 14 m. is very common for transportation tunnels. The guidelines included the following concepts: excavation method, rock bolts (20 mm diameter, fully grouted), shotcrete, steel sets. There is an increasing gap between the 1989 guidelines and the practice: in many tunnels different to-the-case excavation and support requirements are established. Bieniawski himself has published a paper (Lowson & Bieniawski, 2013) with different guidelines based in Lowson’s practice, with no explanations and/or justification.In this paper a new set of RMR tunnelling guidelines is proposed taking account of the actual industry conditions, and increased safety regulations. The 5 classes’ limit RMR:values (80,60,40,20) are no more useful actually: Values of RMR (70, 50, 30) are used in practice to define quite different tunnelling techniques. Consequently a 10 subclasses system is proposed. Each subclass covers a span of 10 RMR points. As the number of mechanically excavated tunnels has increased a new correction factor is necessary, according the excavation method.The proposed 2014 RMR guidelines are for tunnels 10 to 14 meters wide, the world practice for new roads/railways tunnels. Many tunnels for water/ services are smaller with smaller support needs. Wider than 16 m caverns are out of the RMR system.It is not possible, nor desirable, to propose only a value for support in each subclass. The new guidelines propose an interval of values for certain types of support. More pessimistic values must be chosen for wider tunnels, tunnels with lower RMR values in each class and cases when a higher safety factor is asked for. More optimist ones are chosen for narrower tunnels, and higher RMR values. Some alternatives are almost complementary, others are contradictory. Sometimes several different techniques are proposed Guidelines are not automatic options. Good engineering judgment must be used when choosing between the different alternatives. Guidelines are not mandatory suggestions."

Jan 1, 2015

By H. J. B. Couto, J. G. S. Puelles, M. L. Torem, R. H. Rojas, A. G. Merma

Understanding the limits of fine particle flotation is fundamental to achieving a significant and selective separation. Conventional flotation processes are not suitable to treat these particles because of their low collision efficiency. This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. In this sense, this study assesses the effect of current density and pH on bubble size in a binary electroflotation cell. An increase in the bubble generation rate was reported with an increase in current density. In addition, at acid pH values, the size of oxygen bubbles increased and conversely decreased at basic pH values; this may be due to the electrostatic attraction between the oxygen bubbles and the anode resulting in a greater nucleation time. An opposite trend was observed with the hydrogen bubbles. These results are in agreement with their electrokinetic studies, which reported that at acid conditions the bubble surface may be positively charged for both the hydrogen and the oxygen bubbles. Finally the bubble size was slightly affected by the electrolyte concentration, resulting in smaller diameter bubbles at higher concentrations.

Jan 1, 2016

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By G. Issid, J. McGinty, C. Lee, Y. Pepin

For more than a decade, Hatch has used process and logistics models to assist Rio Tinto Fer et Titane (RTFT) with capacity planning, debottlenecking, and optimization to help ensure design capability, capital effectiveness, and operational efficiency of the integrated production chain. Process models are used to optimize the physics-based aspects of the system, such as mass and energy balances, flow rates, yields, and equipment specifications. Dynamic logistics models are used to optimize how the various plant areas work together to achieve the desired ends and deal with such things as plant scheduling and synchronization strategies, sizing of buffers between processes, defining the required number of process and material handling units, and designing a plant layout that minimizes plant interferences and inefficiencies. The combined use of process models and logistics models enables the overall plant to be optimized from both a productivity and quality point of view, with each plant area working in harmony with one another to achieve targeted capacities and efficiencies. This paper describes the many benefits derived from such modeling efforts over the past 15 years for each of the major plant areas at RTFT: Beneficiation Plant, Smelter Plant, Steel Plant, UGS Plant, and Powder Plant (RTMP).

Jan 1, 2011

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009