Search Documents

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By A. Abadías Llamas, N. Bartie, M. Stelter

Evaluating the economic viability as well as the sustainability of the Circular Economy (CE) system requires a deep understanding of the distribution of all elements, compounds, alloys, materials etc. in flows. In this paper, the circularity of the copper value chain, including primary and secondary processing, is rigorously evaluated. The studied system comprises the metallic copper production from primary sources (from mineral to metal), copper-containing commodity production (copper is mixed with other metals) and copper recycling through secondary smelting to close the loop. This is linked to photovoltaic (PV) panels and battery storage. A simulation model of this system is created using HSC Sim, considering more than 30 elements (and its various compounds), 180 unit operations and 800 flows. From the mass and energy balances obtained through the simulation, an exergy analysis is conducted to evaluate the resource consumption from a second law (entropy) perspective. Additionally, these results are complemented through a Life Cycle Assessment (LCA), the recovery of technology elements and by-products is discussed, while quantifying the losses through the value chain. Through the digitalization of the complete system, a better CAPEX and OPEX understanding of the metal recovery and losses can be obtained, as well as the associated resource consumption and environmental impacts. New flowsheets and technologies can be evaluated. Several scenarios show how the resource consumption and the environmental impacts are affected by the recovery of different materials to produce different products. INTRODUCTION A key challenge of the circular economy (CE) is the linkage and optimization of both resource and energy efficiency of the (renewable) energy infrastructure and the resource cycle depicted by Figure 1 simultaneously. In addition, the CE requires the linkage of all stakeholders as shown by Figure 1. This has been discussed in some detail by Reuter and Bartie (2019) and Reuter et al. (2019). Copper and all its associated technology elements is one of the key enabling metals that is an economical copper colored thread through CE society (Reuter & Kojo, 2014). The Metal Wheel (Figure 2) shows the linkage of and recovery of various elements associated with copper and other carrier metals. This reveals that copper acts as an important carrier metal because of its properties i.e. the wealth of technology elements it carries from geological ores, but also its capacity to act as solvent of valuable elements and thence a key closer of various complexly connected element and material cycles when these technology elements are released during copper refining. The same applies to all other carrier metals of modern CE society as shown for example recently in a lead policy brief (Blanpain, Reuter & Malfliet, 2019).

Jan 1, 2019

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By H. J. Oterdoom

SMS Siemag (SMS) has always been the front runner in safety aspects of electric smelter plants for the ferro-alloy and non-ferrous industry. The awareness for safety increased significantly over the past decades and SMS contributed with its design features greatly to a safer design and operation. Today, safety aspects are not only part of the smelter design but also of the overall plant layout. Explosions in electric smelters are rare, but have a huge impact on peoples’ lives, on equipment and on production. For this reason, SMS wanted to have a better overview of explosions within the smelting industry in order to see if useful statistics could be extracted. Generally, there is a lack of statistics regarding explosions in the electric smelting industry, and not enough information is collected or published. A significant portion of the explosions seems to be water related. Many companies, both operating and engineering, are trying to handle the risks of water, and apply methods to detect water leakages. Installing such a system is a management decision and management has then to make sure the system is properly implemented. The disadvantages and limitations of these systems should be carefully considered and communicated to operators and authorities.

Jan 1, 2014

By C. L. Reichardt

Pressure exerted on gold producers by regulators, project financiers and civil society in the wake of the Baia Mare tailings spill in Romania during 2000 prompted most responsible gold companies to sign up to the International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code). The Code stipulates a ?cradle to grave? approach more comprehensive than that applied to any other mining reagent and poses particular challenges for operators who use cyanide-bearing tailings for backfill. This paper examine some of the challenges for Code compliance facing deep underground gold mines that employ backfill technology, most particularly the requirement to demonstrate that the potential migration of cyanide (and its degradation products) from emplaced backfill will not have an unacceptable impact on worker health and safety or the receiving environment, either during mine life or after closure. Although the Code only contains a single reference to backfill, more careful consideration confirms that most sections of the Code that deal with tailings management are potentially applicable to mines where tailings material is used for backfill, as are certain principles pertaining to aspects of operations, worker safety, emergency response, training and dialogue with stakeholders. For gold mines of the Far West Rand, the most significant cyanide-related risks associated with backfill operations relate to worker exposure to cyanide-bearing seepage and HCN gas. There is potential for seepage of cyanide-bearing water from backfill to compromise the beneficial use of surface and groundwater, and thus impact on downstream users and ecosystems. However, the extreme depth of mining and the specific geological and hydrological controls on the Far West Rand suggest that the potential environmental risks associated with backfill are likely to be considerably less significant than the cyanide-related risks to the workforce.

May 1, 2007

By W. R. Bruce, G. W. Hodgson, K. A. Clark

"IntroductionANY PLANT processing mined Athabaska oil •sand for the recovery of oil produces, as a waste material, about one ton of sand for every barrel of oil recovered. A disposal problem of major proportions is thus indicated. For a 100,000-barrel per day plant, provision must be made for moving .about 4,000 tons of sand per hour on a continuous basis to a tailings dump at least several thousand feet removed from the plant site.Of the many known ways of conveying solids on .a large scale, the hydraulic pipeline transfer method is becoming increasingly important because of convenience and economy of operation. It has been in use for many years in mill operations at metalliferrous mines for the disposal of tailings and as such was a natural outgrowth of •hydraulic sluicing (3). Pipeline transportation of mill concentrates has been adopted recently ( 1), wherein high-density solids are moved several miles by hydraulic pipeline. The flotation power of the water suspending the solids may be increased 'by addition of magnetite for the handling of ore in pipelines (8). Low-density solids such as coal have received considerable study for low-cost pipe-lining (2) and a successful operation with coal has been carried out in England with indications of considerable savings over other methods of transportation (9). Dredge operations are based on pipeline transportation for the dredged sol-ids, and the scale of pipelining there .has involved pipe sizes as large as 32-inch (6). However, the tendency has been to regard the pumping of solids in water merely as a simple method of transportation and little consideration has been given in the published literature to study of the most economical modes of operating .a pipeline."

Jan 1, 1952

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005

By S. Kelebek

Efficient separation of minerals is the essence of mineral processing. Separation of hexagonal pyrrhotite in processing of Ni-Cu sulphide ores was investigated together with particle size effects with respect to selective flotation recovery of pentlandite and nickel. The recovery by size response was compared for sodium metabisulphite (SMBS), triethylenetetramine (TETA) and their combinations with amyl xanthate as a collector. The pyrrhotite recovery for all sizes was lower than that of pentlandite for the blank case as well as individual cases with SMBS and TETA. For pyrrhotite, the recovery by size relations in the case of individual uses of reagents were mainly determined by recovery losses at coarser size range (>74 um), which occurs at a coarser size for pentlandite (>212 um). The combined use of SMBS and TETA, and the associated synergistic effect very significantly knocked down the pyrrhotite recovery to less than 7% that was a maximum for the –10 um (attributable to hydraulic entrainment). High recovery of pentlandite in a wide range of intermediate sizes and drastically low recovery of pyrrhotite resulted in a very efficient separation of pentlandite from pyrrhotite in all sizes. Separation of this mineral is discussed in relation to fundamental functionality of the reagents used.

Jan 1, 2017

By Laura Kelsey

Contaminant Robust In Situ Water Extractor CRIWE Nafion-based water clean-up Extract purified water from natural extraterrestrial sources In situ water processing for downstream electrolysis Chemically resistant to process contaminants such as acid

May 1, 2013

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

It is well known that high strength steels used in aerospace industry, are generally susceptible to hydrogen embrittlement during surface treatment such as electroplating with zinc on cadmium. Hydrogen embrittlement reduces ductility and results in brittle fracture rather than failure by plastic deformation. Hydrogen embrittlement of high strength steels is mitigated by surface treatment such as plating with other metals. Data on the hydrogen contents of steels before and after surface treatment by hot extraction-thermal conductivity, secondary ion mass spectrometry (SIMS) and UV-visible spectroscopy along with the mechanism are presented.

Jan 1, 2006

By Stephen Se

Geological assessment of active mine faces enables ore grade control, geological modelling and exploration planning. Monitoring of the mine advancement at every drill-blast-muck cycle allows for effective production management. However, geological assessments are performed infrequently due to the need to travel to active mine faces, and detailed surveys to map the mine progress are performed at the end of the month. Instant Mine Modeller (iMM) is a portable ruggedized stereo-vision system that creates photo-realistic three-dimensional models of underground mine faces on-site. The 3D models are generated automatically within minutes and can be viewed underground and annotated with geological information. The overall ore percentages of the face are calculated automatically for grade control. Annotated 3D models are located in the mine coordinate system and can be imported into mine management systems. iMM allows for daily monitoring of the mine progress and geology, and for re-visiting the mine virtually as it existed. iMM has been deployed in an underground hard rock mine for 18 months, and it effectively brings the underground work face into mine management offices enabling the right decisions at the right time. iMM has demonstrated benefits to various mine processes including grade control, geological mapping, 3D photo-realistic as-built and production volume.

Oct 1, 2009

By Jean-Pierre Birat, François Hanrot, Gérard Danloy

Global warming presents an enormous challenge to the steel industry, which is both carbon-intensive and energy efficient. Lean production can provide some short-term emission mitigation, at the level of the Kyoto requirements. In the middle term, more use of scrap will also help alleviate emissions. But to reach much larger reductions in GHG emissions, on a par with the likely targets that will be set after the Kyoto period, the steel industry will have to imagine new production paradigms, which constitutes its most formidable challenge for the years to come. Carbon capture and sequestration, processes leaner in carbon use, electricity and hydrogen from green sources will have to be added together in a patchwork of process routes, which will have to be developed at great risk in the next decade, hopefully through broad international cooperation.

Jan 1, 2004

By D. D. Tannant, H. Ozturk

Thin spray-on liners are increasingly being used as rock support in underground mines. The adhesive strength between the liner and the rock surface is an important design parameter. Adhesion tests were conducted to assess the impact on adhesion of the presence of oil, water, and dust on a substrate, and the roughness and grain size of different substrates. Other factors such as curing time, loading rate, and liner thickness were also considered. Adhesion was measured using a pull test of a 33 mm diameter elevator bolt attached to an over-cored section of liner with strong epoxy. Most tests were performed using Tekflex liner material, although five other liner products were also tested. Adhesive strengths of about 2 MPa can be achieved with Tekflex under optimal conditions. Long-term creep tests showed that the adhesive strength could drop by at least 50% when the liner carries load for about a month. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa. As the thickness of the liner increases, the adhesive strength to a substrate appears to decrease.

Jan 1, 2007

By P. E. Cavanagh

THE Ontario Research Foundation has developed a family of dry magnetic concentrators which, when used in conjunction with a dry grinding mill such as an Aero-fall mill, will allow the production of a completely dry magnetite concentrate. Previous experience with extrusion of iron ore and with pelletizing of fine iron concentrates suggested that it might be possible to develop a method particularly suited to the agglomeration of completely dry concentrates which might have some practical advantages over other methods of agglomeration. Pelletizing is the preferred method of agglomerating very fine iron ore concentrates. Magnetite concentrate is fod to the pelletizing equipment in the form of a moist filter cake. Binders and plasticizers may be added if necessary, and the moisture content must be increased or adjusted to the percentage necessary to give good balling action and satisfactory green strength in the resulting moist pellets. The moist ore with a closely controlled water content of about 7 to 12 per cent moisture may be rolled into pellets by a snow-balling action in a pelletizing drum, a Lurgi pan, or a Mac-Dowell disc pelletizer. The resulting green pellets are fired by one of several alternative processes to produce a hard pellet which has sufficient strength to withstand handling and shipping.

Jan 1, 1957

By M. Phylli Bray

"Mining has the reputation of being a very ""macho"" industry. Recently, wider educational opportunities for women in nontraditional occupations and changes in mine technology have combined to make mining a viable career choice for women also. To benefit from this new resource, the mining industry faces the challenge of developing a different work environment from the one now burdened with sexism. Management supported initiatives are needed to facilitate such a transformation. The same rethinking of gender attitudes might also be extended to mining women in their traditional role as ""wife of"". The assumption that the male worker&apos;s wife is an unpaid adjunct is being questioned. It is suggested that women&apos;s separate concerns both as helpmate and as part of the mining workforce should be considered when planning for mining into the 21st century.IntroductionI must confess that, during the preparation of this paper, there have been many moments when I questioned my temerity. After all, I am not male, I am not an engineer, and I have never had a position in mine management. But as the wife of a mining engineer and a long-time resident of Northern Ontario mining towns, I do have an interest in the mining industry. This interest has had little to do with the technical and management aspects of the industry. Instead my research has been concerned with the impact the mining industry has on the people involved, particularly women, whether directly as employees or indirectly as wives. As I look toward the 21st century, I believe that the whole question of gender relations in the mining industry is one of the critical management issues smouldering below the surface."

Jan 1, 1995

By Paul T. Fitzgerald

Risk financing solutions are emerging to fully address environmental liabilities for mining operations. Supported by specialized insurance and alternative risk transfer (ART) products, mine owners can fund, cap and guarantee the environmental liabilities and closure obligations of a mine within a financial structure that will be acceptable to regulators. An environmental risk financing program will permit an owner to transfer the liabilities and indeed the ownership of a site to a third party that has the ability and resources to responsibly execute the closure plan. A properly structured program will be financially viable for the owner and will also respond to community and environmental opposition concerns about sustainable development and the environmental legacies associated with mining activities.

Apr 1, 2005

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By G. E. Parsons

"The Bidgood is a small gold mine about 5 miles east of the main Kirkland Lake camp. Since the beginning of production in 1934, gold having a value of $5,000,000 has been produced from the property. Practically all of this production has come from seven veins in a diorite stock that intrudes the Timiskaming sediments and lavas of the area. The veins consist of quartz, pyrite, and molybdenite with minor amounts of chalcopyrite, calcite, and tellurides, and occupy northeast striking and northwest dipping thrust fault fractures. They have no apparent direct structural association with the faults of the main Kirkland Lake camp or the Larder Lake 'break' to the south; however, the veins closely resemble the former in their mineralogical composition and in their close association with syenite intrusives.ROCK TYPES AND THEIR STRUCTURAL CHARACTERISTICSThe dominant and, from an economic standpoint, most important rocks in the ore area consist of two separate families of Algoman intrusivesa diorite and a later syenite group."

Jan 1, 1954

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013