Search Documents

By B. Burke

Magnesium and its alloys are attractive materials for use in automotive and aerospace applications because of the low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. The present paper reviews the efforts to improve the attractiveness of magnesium through non-traditional processing, and presents preliminary results of current work on producing magnesium alloys via powder metallurgy P/M. P/M can be used to alleviate the formability problem through near-net-shape processing, and also allows unique chemical compositions that can lead to new alloys with novel properties. The feasibility of producing magnesium powder metallurgy products utilizing the industrially dominant process of mixed powder blending, uniaxial die compaction and controlled atmosphere sintering was investigated. An alloy composition based on the commercial Mg alloy AZ31 (3% Al, 1% Zn) was used to facilitate comparison to similar wrought products. The optimal processing conditions (compaction pressure, sintering time and temperature, and quenching temperature) were found to maximize sintered density and mechanical properties.

Jan 1, 2007

By L. Hacini, N. Van L ê, P. Bacher, D. Thibault

Manufacturer welded components may suffer from high level of residual stresses which can cause premature cracking and decrease the life of the components if they reach values close to the yield strength of the material. In the present work, a robotized hammer peening technique is simulated by an impact machine and the residual stresses generated by the indentation are measured. To better understand phenomena behind residual stresses relaxation by hammer peening, the impact energy level was changed. 304L steel plates were hammer peened with 10 impacts. The contact between the hammer and sample surface was always at the same location. The strains on the surface close to the impact location were recorded during the test using strain gauges to follow residual stresses variations. At the end of the test residual stresses were measured indepth using hole drilling technique at 8mm from the impact center. The micro-hardness was monitored to evaluate the affected zone by the hammer peening. This approach gave a good estimation of the energy and number of blows to be used for efficient relaxation of the manufactured parts.

Jan 1, 2006

By C. Lapointe

"IntroductionTen years ago, when nuclear fission became practical, the element uranium, until then a not very desirable by-.product of the radium industry, became overnight the strategic material par excellence. One of the several important problems that had to be solved at that time was the rapid and precise determination of uranium in ores and concentrates.GeneralThe chemical analysis of uranium ores is a long and difficult business and is complicated by the presence in most ores of a large number of interfering elements. True, much progress has been made, during the past few years, toward simplification of the analytical methods, but the chemical determination still remains the job of a skilled operator. For this reason, the chemical method has been replaced, whenever possible, by a physical determination based on the measurement of the radiations emitted by the elements of the uranium family. There are several types of instruments suitable for these measurements, but of all the radiation detectors known to the physicist, such as ionization chambers, crystal detectors, scintillation, proportional counters, and the like, the Geiger-Mueller counters have proved to be the most satisfactory for routine determinations, because of their simplicity.The Geiger-Mueller counter is a very versatile instrument; it can be constructed to detect any type of radiation, corpuscular -0r electromagnetic. Here, however, we are interested in these counters because of their ability to detect the beta and the gamma radiations, both emitted by some members of the uranium family. The beta radiation is corpuscular, and is composed of fast electrons, while the gamma radiation is electromagnetic."

Jan 1, 1950

By R. G. L. McCready, Marco Zentilli

"Brogan coal containing mean averages of 6,93% w/w total sulphur (1.1% sulphate sulphur, 1.6% organic sulphur and 4.24% pyritic sulphur) and 16.34% mineral ash was used as the test coal in these studies.Shake-culture leaching studies on seven size fractions of the coal, ranging in size from 0.045 mm to 1.7 mm, showed that the rate of pyrite leaching was inversely proportional to the particle size. As the use of continuous stirred tank reactors would be uneconomical for the reclamation of waste coal, column leaching studies were initiated on coal sieved to >6.35 mm to < 12.7 mm, The leachate was monitored for all metal ions and the release of iron was used to monitor the rate of pyrite oxidation . Measurable amounts of Zn, Co, Ni, Mn, and V, all of which can replace iron in the pyrite crystal structure, were released during the initial stages of leaching. Further, high concentrations of AI, Ca and Sr and trace amounts of Sn, As. Se, B, Ca, Cr, Si, and Ti were detected in the column effluents.These studies suggest that bacterial leaching will remove the pyrite and qualitative amounts of environmentally undesirable trace metals from the coal if such a process is developed for waste coal reclamation.IntroductionIn 1947, Colmer and Hinkle showed that acid mine drainage was the result of an oxidative attack of the iron-mineral sulphides by Thiobacillus ferrooxidans to produce sulphuric acid . Ashmead (1955) proposed the use of these organisms to desulphurize coal , but the subsequent research effort was concentrated on the metabolism and physiology of these extreme acidophiles.A limited number of studies have been reported on the bacterial leaching of pyrite from coal (Silverman et al., 1963; Dugan, 1977). However, the bacterial oxidation of pyrite is a self-limiting first-order reaction, probably due to the precipitation of Fe(OH)J and elemental sulphur , which progressively inhibits intimate contact between the bacterial cells and the sulphide-mineral surface. Consequently, the best pyrite oxidation experiments with coal reported to date required five days to remove 97070 of the pyrite (Dugan &Apel , 1978) using mixed cultures of T. ferrooxidans and T. thiooxidans."

Jan 1, 1985

By Barton G. Stone

The mining and exploration industries have been using Geostatistics (Matheron, 1963) for the past forty years. It has been extensively incorporated into three dimensional block modeling software whose usage has reflected the growth in the use of personal computers since 1980. Because of the utility of geostatistical models in mining and production planning, much of the modern reserve and resource modeling is done by mining engineers, geostatisticians and geological engineers. Explorationists are initially less concerned with three dimensional models until such time as a deposit has been roughly delineated. However, the concept of regionalized variables in ore deposits deals with the effect of spatial correlations between data points in a three dimensional sample space and should be useful for optimizing the spacing of drill holes to allow maximum bang-for-the-buck in drilling programs. This paper examines three common deposit types (porphyry copper, VMS and intrusive gold) to examine whether geostatistical methods have been used to minimize drilling costs because of better understanding of spatial correlations. The three model types were chosen from publicly available corporate websites of Canadian based Junior Mining Companies. They include the Wolverine polymetallic zinc deposit of Yukon Zinc in Yukon, Canada; the El Morro Deposit in Chile (30 percent ownership by New Gold Mining Company, and the Fort Knox Gold deposit in Alaska and 50 percent ownership by Nova Gold Resources). Typically, individual mining corporations post their technical reports as CNI 43-101 reports on their corporate website as indications of the favorability or progress on their more exciting properties. Data considered for this paper was not collected or generated by the author, but the information was extracted from these publicly available sites and had a variety of authorship.

Oct 1, 2009

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By I. V. Kojo

Continuous development of technologies has been self-explanatory for Outokumpu Technology&apos;s engineers for decades. The aim in the development has always been the improvement of profitability of the copper production but also the sustainability of the processing i.e. high copper recovery, low external fossil based energy utilization, high emission captures and of course low operation and investment costs. Outokumpu Technology&apos;s long-term view of the development is a change towards continuous processes and elimination of number of unit operations in smelting i.e. elimination of possible sources of emissions. Outokumpu blister smelting processes i.e. Outokumpu Direct-to-Blister Flash Smelting and Kennecott-Outokumpu Flash Converting have shown excellent operational results during the years of operation and it is expected that soon more than 10 % of the world primary copper is produced by these technologies. The paper will give some background of this development trend.

Jan 1, 2007

By S. Harshaw, C. Doyle, A. E. M. Warner, D. Stremlaw

"In the Utility Nickel furnaces, the hearth and sidewalls are lined with high-Al2O3 bricks. During charging and thermal cycling (more so as the linings on these reverberatory furnaces age), pieces of brick spall or abrade from the refractory and collect on the top of the bath. These pieces are removed using a non-corrosive slag toward the end of the heat when the bath temperature is ~1600°C.This benign liquid can be generated by two methods. First and most obvious, suitable ingredients can be pre-mixed so that the flux (flux A) is isochemical with the non-corrosive slag. All that is needed to produce this targetted slag is heat. Second, in other proportions (flux B), the pre-mixed ingredients generate a corrosive slag that melts completely at -1200 °C and corrodes some but not all of the brick particles on the bath surface. As the reaction progresses, the slag changes composition eventually attaining the targetted benign composition. Using this option, additions are monitored to avoid overfluxing. In both cases, the generated slag/brick mixture can then be rabbled from the furnace. This practice has been successfully used for over two years and has been a factor in extending Utility Nickel furnace life to its current levels (about25% increase)."

Jan 1, 1993

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By L. A. Melis, J. W. Rowson

"Cluff Mining has successfully operated a gold recovery plant at its Cluff Lake operation in northern Saskatchewan to recover gold f rom Phase 1 uranium leach tailings. The operating circuit consists of tailings repulping, grinding, cyanidation, carbon-inpulp, gold recov ery, and cyanide destruction by acidification, volatilization and re-neutralization. The process is described and operating data and metallurgical results from the operation are provided.INTRODUCTIONCluff Mining, a Saskatchewan partnership, is owned 20 per cent by Cameco and 80 per cent by Amok Ltd. /Ltée. (Amok), manager and operator of the partnership.The current operation includes the Phase II uranium mining and milling facilities, located at Cluff Lake, 700 km north of Saskatoon, capable of processing 300 000 tonnes o f ore to produce about 4 000 000 lb UPs (1500 tonnes of uranium) per year.The Phase I operation was initially established to process the very high grade ""0"" uranium orebody from 1980 to 1983. The leach tailings from the Phase I mill operation were found to contain elevated level s of gold . These high gold values were partially due to the gravity pre-concentration step included in the uranium recovery circuit, and to the naturally high levels of gold associated with the uranium mineralization in the""0"" orebody .During the Phase I operation some 6475 tonnes of leach tails were produced and stored in a total o f 2916 large concrete containers (vaults). This method of storage was, at the time, deemed to be the preferred method of temporary storage for the tailings.This temporary storage of high-grade gold tailings facilitated the reclamation and reprocessing of the leach tail s for gold recovery. The primary reason for reprocessing the Phase 1 leach tails was to provide for long-term permanent disposal of the material as an admixture with Phase II tailings in the Cluff Lake tailings disposal area. Although there was limited tonnage, the high gold content in the material made the in stallation of a gold recovery circuit economically justifiable."

Jan 1, 1989

By Kazuteru Tozawa, Robert G. Robins

"The stability of calcium arsenate is discussed in relation to the possible misuse of lime in the treatment of gold processing waste waters. Stability diagrams have been derived and experimental results cited to show that calcium arsenate has a higher solubility in neutral to alkaline solution than has previously been recognized and this solubility is further enhanced by the presence of carbon dioxide, bicarbonate or carbonate.IntroductionThe removal of arsenic from gold mine waste waters has been of interest for more than thirty years, but with the recent emphasis on clean water standards there has been renewed activity in relation to that problem. The processing of gold-bearing sulphides which contain arsenopyrite and other complex arsenic sulphides is well established. Initial roasting to oxidize the sulphides leaves the arsenic in the form of both arsenic and arsenic, in which forms it is soluble in the subsequent leaching stage. Further oxidation of the leach liquors is required before the well-established procedure of precipitating calcium arsenate with lime, which is carried out despite an immense lack of knowledge of the calcium-arsenic-water system.The solubility product and free energy of formation for Ca3(AsO4)2, which are to be found in recent and reliable sources of data, originate from the work of Chukhlansev, whose experimental determination of the concentration of calcium from the solubility of calcium arsenate in solutions of various pH yields the results plotted in Figure 1. This is the work which has resulted in a wide acceptance of the ""insolubility"" of calcium arsenate and the use of lime to stabilize arsenic in that form.Laguitton attempted to further elucidate the chemistry of the lime addition method for treating arsenical waste waters from gold processing operations. The low solubility product for Ca3(AsO4)2 was the basis for his examination of likely chemical equilibria in the system. Laguitton and other workers have not considered atmospheric carbon dioxide as an important component in this system."

Jan 1, 1982

By P. A. Riveros

The literature on the arsenic disposal practices of the metallurgical industry and the long term stability of the disposed arsenic compounds were reviewed from a Canadian perspective. The review was complemented with visits to selected operating metallurgical sites to obtain information on their specific arsenic disposal practices and the behaviour of their impounded residues. The arsenic disposal procedure currently favoured by the industry involves the formation of an insoluble ferric arsenate compound which is allowed to sediment at the bottom of tailings or residue ponds. It has been shown recently that this poorly formed crystalline compound is similar to ?arsenical ferrihydrite? which is ferrihydrite containing strongly adsorbed arsenate anions. Despite concerns about its long term stability on thermodynamic grounds, arsenical ferrihydrite appears to be stable for many years in the proper environment which includes a slightly acidic pH and oxidizing conditions. A high Fe/As ratio and the presence of heavy metals appear to increase the stability of arsenical ferrihydrite. High temperature operations, such as those encountered in the autoclave treatment of refractory gold ores, are conducive to the formation of scorodite, FeAsO42H2O, and/or a series of ferric arseno-hydroxy-sulphate compounds depending on the solution composition. Scorodite has several advantages over arsenical ferrihydrite as a disposal compound including a lower iron demand, a higher density and a greater thermodynamic stability. New procedures have been developed to generate scorodite at ambient pressure. These procedures would offer significant reductions in capital cost because of the elimination of the need for autoclaves. Lime precipitation which was widely used in the past is being abandoned as a result of strong evidence showing that calcium arsenate compounds decompose slowly in contact with atmospheric CO2 to form calcium carbonate and soluble arsenic acid. In all cases, the long term stability of the disposed arsenic compounds depends on a number of factors including disposal site characteristics, particle crystallinity and size distribution, the presence of complexing agents and the effect of bacterial activity.

May 1, 2002

By Michele L. Kimble

A fast-flow reactor mass spectrometer has been utilized to investigate the reactions of gas-phase gold cluster anions with CO and oxygen. Addition of CO to Aun - produces species of the form Au(CO)m -, where m = 2-5. However, CO does not bind to Au2 - or Au3 -. With oxygen addition in the cluster source, gold oxide species with both molecular and atomized oxygen are produced. The addition of carbon monoxide to these preoxidized gold cluster anions reveals that select species with 1, 2, and 3 gold atoms participate in the oxidation reaction to produce CO2. Bimolecular rate constants for the reactions between these species and CO are also discussed.

Oct 1, 2003

By Hao Zhang

Site inspection is an important component of safety management system. In current practices, the inspectors evaluate the safety condition on a construction site with the assistance of a standardised checklist. However, the checklist emphasizes on evaluating the implementation of safety management system, but provides limited task-specific check items for assessing whether the individual construction tasks are conducted under safe condition and in a safe manner. To address this issue, the research presented in this paper aims to provide safety practitioners with comprehensive and taskspecific safety information to promote effective risk identification and facilitate strategic risk control during site inspection. Specifically, this research first builds a project-specific safety information database, which stores potential risks and control measures for each construction task. The research team then develops a mobile decision support tool to retrieve information from the database and support safer decision-making on site. The tool supports users in two ways: one is to provide daily risk checklists and risk control strategies to guide step-by-step inspection alongside the project schedule; the other is to let users input any safety-related keywords during the safety inspection process and the tool returns relevant safety information by applying text mining algorithms. It is ongoing research. This paper presents an overall research framework and discusses the progress in developing safety database and data retrieval concepts. The outcome of the project will help enhance safety management practices and reduce possible risky working conditions on a construction site.

Aug 1, 2013

By G. F. Miller

ONLY IN THE Province of Saskatchewan is natural sodium sulphate found in Canada in amounts large enough to make recovery economically sound. Geologists have estimated that the numerous deposits within the Province contain upwards of 200 million tons of Glauber&apos;s salt. There are twenty-one deposits in the Province which contain 500,-000 or more tons and about two dozen with lesser amounts. The first recorded production of sodium sulphate in Saskatchewan was in 1918. The company concerned, and others that attempted to develop the industry in its early stages, were unsuccessful. Their failures were caused by two main factors -lack of knowledge of efficient operating methods and the unstable market situation for the finished product. Today, the situation is changed in both respects and the product, commonly referred to as &apos;saltcake", is a very important chemical requirement of many industries throughout the world. Before proceeding with remarks on manufacturing methods it should be stated that, although this is a general paper on the manufacturing methods and end uses of the saltcake produced in the Province, the writer is, of course, more familiar with the plants operated by Saskatchewan Minerals than with other operations and perhaps may be excused for dealing more particularly with the plants of that Compa11y.

Jan 1, 1958

By E. Sharifi, B. Komishke, R. Heffel, D. Schwartz

"The oil sands resources in Canada are one of the world’s largest hydrocarbon deposits. Processing of oil sands uses hot water to extract bitumen. The process generates tailings slurry that must be settled for final deposition. The tailings contain fine material, with poor water release characteristics which makes water recovery challenging. Polymer flocculants are added to assist in settling and dewatering the fine tailings. The amount of polymer addition is dependent on tailings characteristics, including the particle size distribution (PSD). If the PSD of the tailings is unknown, an excess amount of polymer needs to be added in the dewatering stage to flocculate the particles. Over flocculation also has a detrimental effect on the water release characteristics. Measuring the particle size distribution using an on-line analyzer could have major benefits over common laboratory methods as it provides online and fast insight into the process enabling the operators to implement required changes to minimize the reagent consumption, while achieving optimal flocculation. Online measurement of PSD using laser diffraction has long been used in base metals beneficiation processes. A series of test work using Outotec PSI500® particle size analyzer on oil sands samples from different operations have been conducted. Tests were performed by recirculating the slurry in closed circuit to simulate real plant conditions. This paper presents a summary of the results.INTRODUCTION Canada’s oil sands are the third largest reserves of crude oil in the world, with an estimated 165.4 billion barrels of recoverable oil (Government of Alberta 2016). Oil sands are a mixture of sand, water, clay and bitumen. Bitumen is a form of oil that is too heavy or thick to flow or be pumped without being diluted or heated. About 20% of bitumen reserves are close enough to surface to be mined. In mining methods, oil sand is transported from an open pit mine to the processing plant and bitumen is separated from solids and water. The separation process involves ore preparation, such as addition of hot water, steam and caustic (NaOH), followed by gravity separation and froth treatment (Masliyah et al. 2004). A general scheme of the extraction process is presented in Figure 1."

Jan 1, 2018

By K. Hawboldt, J. E. Halfyard, C. Bottaro

The removal of sulfur from leach residues has been practised in the zinc industry using a combination of flotation and hot melt filtration. The process is highly dependent on the nature of the concentrate and the subsequent residue. When the mineral constituency of the residue alters, the process can encounter significant operational challenges. An alternate method of converting elemental sulfur to water-soluble polysulfides was applied to leach residue from Vale&apos;s nickel demonstration plant in Argentia, Newfoundland. Reaction parameters, sulfur purity and other key indicators are discussed as is the potential commercial application.

Jan 1, 2011

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, F. J. Tavitas-Medrano

319-type cast Al-Si-Cu-Mg alloys are commercially important due to their popular use in automotive applications. Artificial aging heat treatments are commonly performed in these alloys to achieve precipitation hardening and, therefore, improve their mechanical properties. The present work was carried out to investigate the effect of conventional (at a constant temperature, as specified by the standard T6 heat treatment regime), and non-conventional multi-temperature and interrupted aging cycles on the hardness, tensile and impact properties of two 319-type alloys (with and without Sr+ Mg additions). The results show that certain multi-temperature aging cycles have a more favourable effect in improving some mechanical properties than conventional cycles.

Jan 1, 2006

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore &apos;as mined&apos; generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935