Search Documents

By J. E. Moyle

The costs of labour and electric power are of prime concern to almost all industrial enterprises, and various methods of reducing their impact on production costs are constantly being developed. Automation is one of these schemes, and has received a good deal of attention in the past few years. In the mining industry, compressed air is almost universally used, and its cost is significant. Although the compressor machinery now in use has achieved a high degree of development, the hazard of explosion and fire still exists in these systems. There is thus considerable resistance in some quarters to suggestions that such installations can be safely and successfully automated. The Milliken power plant consists of two 30,000 lb. /hr. fully equipped high-pressure boilers, four H.P. air compressors, a steam turbine for stand-by power, and several L.P. compressors and vacuum pumps. With the installation of automatic and protective equipment in the machinery section, the shift force has been reduced from three to two men.

Jan 1, 1963

By Ivor da Cunha

Ontario Mining Association (OMA) represents 57 members that are engaged in exploring, producing & processing mineral resources in an environmentally responsible manner. Conservation Bureau at the Ontario Power Authority (OPA) develops, coordinates and stimulates commitment to electricity conservation and demand management programs ? OMA selected compressed air optimization for high impact cost savings and energy efficiency potential ? Ontario Power Authority (OPA) provided $218k funding for $532k project ? Commenced summer 2006, Final Report June 2007 ? Three representative sites participating: ? Williams, CVRD Inco & FNX McCreedy ? Different levels of energy management ? Small, medium and large mining operations ? Different corporate practices and culture

May 1, 2007

By W. H. Fertl, S. J. Pirson

Well logging techniques, as used successfully in oil and gas exploration, can also be used to give a detailed evaluation of drill holes through industrial mineral deposits such as sulphur. This paper describes the logging tools used gives the theory behind the well-log interpretation and discusses the application of the method in sulphur-bearing limestone and m more complex sulphur deposits.

Jan 1, 1970

By M. H. Colebrook

Nickel laterites contain about 70% of all continental or terrestrial nickel resources; therefore the recovery of nickel from lateritic ores has large economic significance. The processing of lateritic ores involves the preparation and movement of concentrated aqueous suspensions. However due to complex characteristics and non-Newtonian properties, ranging from shear-thinning to shear-thickening and from thixotropic to rheopectic, a basic understanding of the flow behaviour must be developed. This understanding will assist in the development of new plants and the operation of existing plants. The work in this paper involves the characterization of three ore types from the Vermelho ore deposit to categorize them as rheologically simple to complex. Rheological testing was also conducted on pure mineral samples that represent the main minerals in these samples. The results show that the rheological properties of the ore types can be related to the surface properties and physical characteristics of the main mineral constituents.

Jan 1, 2006

By Mitchell P. Rothman

This paper concentrates on profits and other measures of return in the Canadian mining industry, especially in the non-mineral-fuels sector. The paper examines the historical patterns of mining profits, both before and after taxes, as compared with profits in other sectors of the Canadian economy, as well as some of the more important influences on mining profits. These include the prices of mineral products, provincial and federal tax policies with respect to mining , and the effect of inflation on mining profits and the financial position of mining firms - in each case, comparing mining with the other sectors of the economy. Finally, the paper provides an analysis of current and prospective rates of mining profits in relation to the capital required to ensure the future viability of the Canadian mining industry.

Jan 1, 1977

By J. T. Fyles, C. G. Hewlett

"THE REEVES MACDONALD mine is in the Sa Imo-Pend d'Oreille mining area of southeastern British Columbia. It is on the Nelway-Waneta road 4 miles west of the border-crossing point of Nelway. The Reeves orebody from which all production has come is one of several mineralized zones in easterly-striking limestones occurring between the Pend d'Oreille and the lower part of Salmo River.The property was originally located as two groups of claims by R. M, Reeves and J. H. McDonald. The two groups were consolidated in 1925. and extensive development work was done from then until 1930 and again in 1937, but no ore was shipped. The mine was reopened in 1947 and, between 1949 and 1953, 1,057,804 tons of ore was mined. Concentrates recovered contained 85,626 ounces of silver, 19,394,092 pounds of lead, 72,076,495 pounds of zinc, and 455,051 pounds of cadmium. Low metal prices forced the mine to close in 1953, but operations were resumed in November, 1955.The orebodies at the Reeves MacDonald mine are steeply plunging lead and zinc sulphide replacement deposits in a banded limestone named the Reeves limestone. The orebodies contain pyrite, honey-coloured sphalerite, and galena, and are surrounded by a dolomitized zone. In the Reeves orebody, where the relationships are known, the dolomite has the same general shape as the orebody. Four zones of sulphides are known on the property (see Figure 1). Three of these, the Reeves, B. L., and O'Donnell, are believed to be faulted segments of one mineralized zone. The fourth, the Point ore zone, exposed on the north bank of the Pend d'Oreille River, is not developed and its structural position is not known, but it appears to be a separate deposit."

Jan 1, 1949

By A. Gutiérrez

At present, most ore milling is done in tumbling mills, consisting of huge cylinders turning on their horizontal axis. This rotational motion causes the ore charge and the grinding balls to interact by impact, compression and abrasion, to reduce the size of the ore. This method is very inefficient since only around 12% of the energy supplied is used for actual grinding, the rest being used in moving the large mass of balls and ore within the mill. This work aimed at better understanding the milling process by evaluating the movement of the load through the Discrete Elements Method (DEM). First, the number of bodies (balls and ore) moving inside the mill is determined, to correlate to the potential impacts that constitute one of the milling mechanisms. Then, the number of high energy impacts is evaluated to correlate to the bodies in motion. At this stage, a differentiation between grinding media and the ore, as well as between the types of contact taking place in the mill, has to be made. This latter issue is of great relevance since from the five identified contact types (ball-ball, ball-liner, ore-ore, ball-ore and ore-liner) only the last three actually contribute to the milling process, the other two causing structural damage to the mill.

Jan 1, 2007

SOFCs with thin electrolyte of two types: SDC (15um) single-layer and YSZ (5um) + SDC (15um) bi-layer were fabricated by screen printing and co-firing on Ni¬YSZ cermet substrates. Using in-situ sintered Sm0.5Sr0.5CoO3 cathode the SDC-cell shows high performance at low temperature, 1180mW/cm2 peak power density around 650°C, while the YSZ+SDC bi-layer cell generates about 340mW/cm2 at 650°C, and good performance at 700-800°C with almost theoretical OCV value. Many Zr-content micro-islands were found on the SDC electrolyte surface. The influence of co-firing temperature and thin film preparation methods on the Zr-islands' appearance was investigated.

Jan 1, 2005

By S. U. Baltuch, E. G. Baltuch

"Ventilation in process buildings is key to proper mill function. Correctly engineered systems to evacuate surplus thermal energy from process areas allow optimized rates of air change, thus assuring the good functioning for the lifecycle of the process while demonstrating conformity with occupational hygiene standards. Computational fluid dynamic simulations, coupled with traditional calculations and physical modeling, can demonstrate to end users and assist engineers in the optimization of mill ventilation, reducing total installation costs while assuring that the proper solution is in place for the complete lifecycle of the process equipment. Results have been fully implemented on a number of steel mill and aluminium smelter applications and we continue to study, optimize, and innovate as new tools become available to provide the best possible engineered solutions for particular applications. INTRODUCTIONThe objective of this research project is the development and implementation of modern approaches and computational fluid dynamics (CFD) simulation in the engineering of green ventilation of hot process buildings. This will assure the predictive performance and improve the quality and ease of construction of industrial gravity ventilation equipment, along with the adjunct hot process buildings, while lowering the overall project costs and time to completion.In order for a hot process building, such as a steel mill, to properly function, heat must be extracted from within. This is accomplished by having air inlets at the bottom of the building and outlets at its apex. The reason for this is to maximize the potential chimney effect. When using stack (buoyancy) effect ventilation, the process heat becomes the driver. Therefore, increasing this distance (height) improves the ability of the heated airstream to utilize basic gravity for acceleration of the heat/air flow, allowing a regular number of air changes per hour while ensuring that the process environment remains weather resistant under normal operating conditions.This process has been understood since the time of King Charles I of England, who decreed in 1600 that buildings should have 10 foot ceilings and that windows should be made taller rather than wider to allow better smoke extraction.Figure 1 is a painting of the Bethlehem Steel Works in the 1860s, where the concept of air inlets and penthouses on the roofs for air outlet was already being put into practice. Figure 2 is an early photograph of the Pittsburgh Steel Works."

Jan 1, 2012

By N. Melnyk

IN the past, the Cadomin Coal Company has opened four mines, all in the same coal seam or its folds. Three of these were opened from river level by horizontal entries or rock tunnels, and the fourth, the present working mine, by vertical shafts. This paper deals largely with some operating phases of this fourth mine, with which the writer has been associated. The seam worked here is a thick, steep, bituminous seam, and the writer feels there is a paucity of published data on the mining of such seams. Possible reasons for this are that such seams do not !end themselves to intensive development or mining, there is little chance to mechanize because of the extreme pitch, and operations are fraught with many problems. In addition, the present operations in this particular seam are being carried on at a level below the former workings, introducing new problems, not en-countered on the upper level. Coal will, without question, long continue to be an important factor in the national economy, and some of the best coal is to be found in thick, steep seams. But with the exhaustion of the easily-mined coal near the outcrops, future coal will have to come more and more from lower levels. At Cadomin there is still considerable coal on the second level, below the old river-workings, and there is a possibility that, in the future, still lower levels will be worked. It is the purpose of this paper to indicate some phases of such lower-level operations and to invite discussion.

Jan 1, 1942

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world's largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article's author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By S. Homulos

"Introductory and GeneralTHE Northwest Territories comprise all that region -of Canada lying between Yukon Territory and Hudson bay and north of the 60th parallel of latitude. For purposes of mine .administration the Territories are divided into three districts: Yellowknife, McKenzie, and Arctic and Hudson Bay. Mining recording offices for the respective districts are maintained at Yellowknife, Fort Smith, and Ottawa. The mine inspection for the entire area, and also for Yukon Territory, comes under the Federal Department of Resources and Development. Two mining inspectors are responsible for these inspections: the Chief Inspector of Mines, with headquarters in Ottawa, who makes trips into the north at least twice a year, and a Resident Inspector, stationed in Yellowknife.The Resident Inspector is constantly making inspections of active properties. This involves a considerable amount of air travel as the region is large and properties are widely scattered.Although there has been prospecting and staking of claims in each of the three districts of the Northwest Territories, actual mining has been conducted only in the Yellowknife district, and for purposes of this paper we are solely concerned with that district."

Jan 1, 1952

By J. E. Hawley

"The property of Francoeur Gold Mines, Limited, lies directly west of the Armfield mine in Beauchastel township, Abitibi district, and 12 miles west and slightly south of Noranda. The gold deposits are of particular interest because of their replacement character and close association with fault zones. The property was originally staked in 1923 following the discovery oi a mineralized zone near the eastern boundary. This became No. 1 orebody. Later discoveries in 1936 of No. 2 and No. 3 orebodies led to underground development and actual mining in July, 1938. A fourth orebody, No. 8, was found in 1939.The following is the production record up to December 31st, 1947:Beginning in September, 1944, ore was shipped to Noranda as siliceous flux, but late in 1946 milling of low-silica ore from No. 1 orebody was undertaken until operations were temporarily suspended in 1947.The four main ore deposits, Nos. 1, 2, 3, and 8, consist of siliceous ferrocarbonate and albite replacement bodies mineralized with fine pyrite and specularite in schistose fault zones in Keewatin volcanics. Barren to low grade quartz veins though present in some are uncommon, but small stringers of quartz are usually present wherever here and there visible gold is found. Nos. 1, 2, and 3 deposits lie in a major fault zone that extends completely across the property from west to east (over 7,000 feet) and dips N.40° to 50°, and are separated by intervals of 1,800 to 2,000 feet respectively. The fourth lies in a smaller fault zone striking east and dipping on the average 65°S.No. 1 orebody has been explored by mining to a depth of 500 feet, No. 2 to 400 feet, and No. 3 to slightly less than 300 feet . The greater part of No. 8 lies above a depth of 200 feet, but a raise has recently .been driven through from the west end of the 5th level of No. 1 to the 2nd level on No. 8 zone. Most of the ore of No. 8 zone above the 2nd level and of Nos. 2 and 3 above the 3rd levels has been removed."

Jan 1, 1954

By J. M. Hollicky

The economical processing of wet and sour natural gas presents a problem due to the seasonal demand for natural gas. The plants must be sized to handle the peak loads but may only operate at half capacity on the average, in which case the sales value of sulphur and hydro-carbon liquid by-products cannot support the operating and capital costs of the plant. This must result in an increased price for the gas. This problem was solved by Pacific Petroleums and Westcoast Transmission in the design of their pipeline and plant facilities now operating in the Peace River area, where there are both wet and dry gas fields. By .building a plant to process sufficient wet gas to pro-vide the base load requirement, and by drawing on the dry gas fields for peak loads, an optimum economic operation was ?possible. The sulphur, L.P.G., and gasoline produced not only are able to support the operating and capital costs of the pro-cessing plant, but were instrumental in the sharp drop in retail prices of these commodities in the area. The sour gas and condensate is gathered from the fields in the area and transmitted in a two-phase gathering system to the gas processing plant at Taylor, B.C. The condenrnte is knocked out in inlet scrubbers. Hydrogen sulphide and carbon dioxide are removed in an amine scrubbing unit. The hydrogen sulphide is stripped from the amine and is sent to the Jefferson Lake Sulphur Company's plant which produces sulphur by the partial oxidation of the hydrogen sulphide. The natural gas, now sweet, is processed in an absorption unit to recover additional liquids, before being de-hydrated to remove water. It is then sent to Westcoast's main c8mpression station. The condensate recovered in the inlet scrubbers and the liquid re-covered in the absorption unit are fractionated to remove fuel gas, used in the plant, and to produce pro-pane, butane, and naphtha. The pro-pane and butane are scrubbed with caustic soda to remove hydrogen sulphide. The naphtha is treated with hydrogen in a unifiner unit to re-move sulphur compounds completely, and is split into a light and heavy naphtha. The heavy naphtha is .catalytically reformed to produce a high-octane blending-component. These fractions are blended with components produced from crude oil at the Dawson Creek refinery to produce a high-quality balanced gasoline with special attention being paid to volatility for ease of starting, warm up, and engine cleanliness, and octane for power and ?performance.

Jan 1, 1958

By R. T. Erskine

"The No. 6 orebody is located 6 miles from the main op.eration of Brunswick Mining and Smelting Corporation Limited and includes open-pit and primary gyratory crushing facilities. Ore is transferred by truck to the secondary crushing facility at the main plant. About 3,500 tons of ore per day are crushed to minus % in. and ground to 68 per cent minus 400 mesh in rod and ball mills for flotation feed. Conditioning and aeration precede rougher flotation, and four stages of cleaning bring concentrates to a grade of 42 per cent Pb + Zn + Cu. Middling products are reground and refloated in a secondary flotation circuit, producing a cleaner feed and a final tails product. Primary bulk concentrate is treated with sulphur dioxide and steam-heated to l 70°F and the majority of the gangue is floated off, leaving a product that assays 57 per cent combined Pb + Zn + Cu and is suitable for marketing. This material is thickened, filtered, dried and loaded into railway cars for shipment to the smelter. Reagent use on flotation is conventional, with many compromises in dosage required to maintain the recovery of lead and zinc in the most advantageous proportions. Many refinements in the flowsheet have been made since start-up in 1966, and more may be made as laboratory and plant testwork indicate possible improvements."

Jan 1, 1971

By Z. Trojanová

Mg micropowders generated by gas atomisation of a magnesium melt with argon were mixed and ball milled with ceramic nanoparticles prepared by laser-induced gas phase reaction. The materials were then hot extruded. Specimens were deformed in tensile as well as compression tests at temperatures between 20 and 300 °C at a constant initial strain rate. The flow stress is significantly influenced by the test temperature. The yield stress decreases with temperature. This decrease and the flat character of the stressstrain curves at elevated temperatures indicate possible contributions of softening processes. The materials studied exhibit high-damping characteristics. The results are analysed and possible mechanisms are discussed.

Jan 1, 2006

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, P. Ghobadi

Design and selection of equipment for a grinding circuit strongly depends on the mill function, ore properties and requirements of the down-stream circuit. Primary mills usually work in open circuit and size distribution of product would be controlled in the final steps using a classifier like cyclone. Although HPGRs are mostly utilized as pre-grinding mills, it is preferred to utilize them in a closed circuit due to their specific mechanism of comminution. Unique mechanical design of HPGR and its completely different crushing process than tumbling mills needs precise consideration on its circuit design. In this paper, we investigate the impact of different parameters on design of pre-grinding HPGR circuit and selection of the proper classifier. Our study focuses on iron ore properties (e.g. moisture, particle size distribution of feed and product, compatibility and de-agglomerability). We also investigated various options of HPGR circuit according the classifier efficiency and influences on down-stream processes. The optimum operating parameters of HPGR (working pressure, speed and level of hopper) for the selected circuit were also determined based on pilot and industrial data. Our pilot and industrial tests and observations revealed that HPGR should be arranged in closed circuit because of the edge effect, as a negative factor of non-uniform distribution of pressure force along the roller width and presence of non-crushed particles in the mill product. Wet vibratory screen could be the optimum option for screening of its discharge. Fine part of the wet screen discharge could be delivered to the concentration stage without over-grinding in ball mill using a hydrocyclone working in a reverse closed circuit mode. Moreover, our pilot and industrial tests during design and operation of ten HPGRs in various iron ore processing plants proved that higher pressure and lower roller speed in a fixed level of material inside the hopper could give the desired product size distribution.

Jan 1, 2016

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By R. C. Gegg

The property of MacLeod-Cockshutt Gold Mines, Limited, is in the Little Long Lac area of the Thunder Bay Mining Division, Ontario, about four miles south of the Canadian National railway station of Geraldton. The town of Geraldton is about 170 miles east of Port Arthur and 22 miles west of Long Lac, which is on the main line of the Canadian National railway. The Trans-Canada highway passes through the property and during the winter season the road is maintained between Port Arthur and Long Lac. Electric power is supplied by the Hydro-Electric Commission of Ontario from their Cameron Falls plant and is distributed at 44,000 volts by a local transformer station. Early History The South orebody was discovered by diamond drilling in the spring of 1936. This is a porphyry contact orebody with major pyrite and minor arsenopyrite mineralization. Some gold is present in the 'free' state, but for the most part it is locked in the pyrite, with little or none in the arsenopyrite. Preliminary test work was based on comparing straight cyanidation with bulk flotation and cyanidation of the concentrates. The overall results by the two methods were found similar, but for economic reasons the flotation-cyanidation process was adopted. Before the mill came into operation, a new and entirely different type of orebody, consisting of massive sulphide lenses in banded iron formation, was discovered to the north of the existing workings. These bodies are an intricate mixture of pyrite and arsenopyrite, both carying gold.

Jan 1, 1949