Search Documents

By R. E. Hamilton

"The requirements for effective optimization of a mineral dressing operation are discussed, with specific reference to a flotation system . Also considered are the relation-ships between automatic control and optimization pro-grams. Variables are classified into the following groups, and the significance of the classification is discussed: (a) Directly measurable (b) Directly manipulable (c) Uncontrollable (d) Calculable from measurable variables (e) Affected by changes in manipulable or uncontrol-lable variables. New sensors for measuring variables not normally measured are described."

Jan 1, 1967

By J. Kan

In order to determine the recovery functions in an oil sand circuit it is necessary to have more than a minimal determination the mass flows in the network. This over-determination is essential in order to allow for measurements within the flow matrix "to flex" according to an error function. It is then possible to identify the flows and composition at all points with maximum likelihood. These so-called full mappings are not easily obtained. However, in order to obtain an unequivocal determination of all the unit operations recoveries such a balance is needed. When databases are constructed exclusively with coherently balanced sets of data it is possible to obtain a maximally accurate process model by maximizing the probability of correctly identifying the process causality. Indeed, it is doubtful in cases of normal complexity that any sense can be made of data that is not so balanced. Coherent mass energy balancing is a tool developed by mineral processing scientists and engineers. Its rigorous application to oil sands is the subject of this paper. The additional element associated with hydrocarbon requires special considerations. It is shown that at least one currently available mineral processing tool will solve the full-mapping problem for an oil sand operation. Experimental design constraints are discussed in this paper relating to the development of databases for the development of effective process models.

May 1, 2004

By W. G. McBride

The mining industry has already become highly technical in all its branches and this has brought about specialization in mining engineering. Increasing demand for mineral products, exhaustion of high-grade or easily worked deposits, and narrowing of the fields for exploration and development, are forcing mines to greater depth and to working material of lower grade and more complex composition. The Robinson Deep at its Turf shaft has reached a depth of 7,640 feet and expects to go to 8,500 feet; Miami Copper, under normal market conditions, profitably mines ore running only 16 pounds of copper to the ton; Alaska Juneau is making a profit on ore running about $1.15 per ton in gold; and many mines are handling ores of an extremely complex nature. In each case, the success of these operations has depended upon the application of sound scientific principles and good business methods to the problems involved. It may be safely assumed that mining at great depth and the exploitation of low-grade, or complex, ores will become more and more important as time goes on, and this means that greater and greater demands will be made upon the technical skill and business ability of the mining engineer. To meet this condition, the more or less haphazard methods of training the young engineer that have prevailed in the past will have to be replaced by a careful and well-ordered system of engineer-training. Upon the industry and the older mining engineer falls the duty of providing means to assist the deserving student to prepare himself properly to meet the increased demands that are falling upon his profession. Consideration of the training of the mining engineer involves a decision as to what constitutes his field of usefulness. Technical control of methods and processes obviously falls upon the engineer, but there are still many who doubt his usefulness in the executive field, particularly in positions involving close contact with the men and work. Many engineers have failed as shift-boss or foreman, but this has been generally due to fault in the management in using men who were temperamentally unfit to lead others or who lacked the necessary preliminary training.

Jan 1, 1932

By R. B. Nourse, S. F. Gwynn-Jones, S. Nikolic, M. L. Bakker, I. McDougall, H. Joubert

"Tenova Pyromet’s core furnace knowhow and expertise has been built within the ferroalloy and nickel/platinum group metal (PGM) industries with the supply of electric furnaces for a number of nickel/PGM operators, including Eastplats, Lonmin, and Anglo-Platinum in South Africa, Mineraçào Serra Da Fortaleza in Brazil, and Norilsk Nickel in Russia. Tenova Pyromet has also supplied the electrode columns and associated electrode equipment – the heart of the electric furnace technology – for cobalt recovery in furnaces in Zambia and the Democratic Republic of the Congo. The quantity and size of projects undertaken by Tenova Pyromet has provided the opportunity to continuously improve furnace designs and the scope of supply, culminating in the most recent nickel/PGM project currently under construction at Northam Platinum. Through this innovative culture, the Tenova Pyromet Base Metals Initiative was formed in 2015 to develop the Novasmelt™ Furnace; a next generation optimised Top Submerged Lance (TSL) furnace design. The combination of Tenova Pyromet’s advanced Novasmelt™ product with our industry leading electric furnace technology are discussed with reference to applications for nickel and cobalt production. Flowsheet arrangements are compared summarising potential capital savings, operating requirements and achievement of downstream product quality.INTRODUCTION Tenova Pyromet is a leading player in the field of smelting technology development and equipment supply. Tenova Pyromet is the result of the union of three furnace suppliers under the Tenova banner: Techint Technologies (Tagliaferri), Core Furnace Systems Corp (Lectromelt) and Pyromet Technologies. The furnace experience of the combined groups dates back over a century with the earliest Lectromelt going into production in the early 1900s. Throughout the modern era, Tenova Pyromet has developed a reputation for providing dependable innovative smelting technology, high quality equipment and sound project execution to a worldwide client base with customer plants operating in Europe, Southern Africa, North America, South America, Russia, Kazakhstan, the Middle East, South Korea, and India. Tenova Pyromet’s core knowledge and expertise was developed in the South African ferroalloy, base metals, and platinum group metals (PGM) smelting industries. Tenova Pyromet has spent considerable effort on development and has contributed significantly to improve the state of the smelting industry. Tenova Pyromet’s electrode columns have become widely renowned and are now providing significant benefits, especially in increased furnace availability, to many smelting furnace operators. The electrode column is the heart of the furnace as it delivers a controlled amount of electrical energy, at an optimum depth in the burden/bath, to the smelting process. Every furnace is custom designed to the specific operating range and optimal operating point of that furnace and process"

Jan 1, 2017

By W W. Moorhouse

A survey of recent literature indicates that sulphides occur in the volcanic rocks of the Archean, or in sedimentary rocks intercalated with the volcanic rocks. The thick sedimentary sections are generally poor in sulphides. Thus, the widespread pyrite and pyrrhotite mineralization in the Archean may be largely of volcanic origin. Introduction I N this paper, commercial base-metal deposits will not be considered, as they are dealt with in other papers of the Symposium. Instead, attention will be focused on those sulphides, often associated with graphitic argillites or tuffs, which have appeared in such embarrassing abundance in electromagnetic surveys of Archean areas. The data on which the paper is based are drawn from recent reports of the Ontario Department of Mines, the Quebec Department of Natural Resources and the Geological Survey of Canada. The information available from these sources is unfortunately limited, because sulphides commonly occur in sheared rocks, such as black argillites and tuffs, which rarely form conspicuous outcrops, and may not be exposed at all. Thus, in the absence of geophysical information, even detailed mapping may fail to reveal the presence of sulphide-rich rocks.

Jan 1, 1965

By J. D. McFarlane, V. Robinson

"The paper begins with a brief account of the naturarly occurring resources of gypsum and anhydrite and a discussion of their relative value and utility as sources of sulphur. The fundamental chemistry of recovering sul-phur values from calcium sulphate is discussed. (a) Thermal decomposition -discussed as impracticable; (b) Reduction to calcium sulphide; (i) Total Reduction-The chemistry is outlined and the Dorr-Oliver and Bureau of Mines processes mentioned. The Elcor process is mentioned and certain deductions made from available information.(ii) Partial Reduction-This is stated as the basis of the only proven process, namely ""The Cement -Sulphuric Acid Process."" The possibility of recovering lime is mentioned as an aside, but dismissed for lack of commercial application. The history of the cement -sulphuric acid process is covered briefly and a list of plants in commercial operation included. A brief elementary account of the basic chemistry of cement production is followed by a discussion on raw materials and fuels. A short account of the flow scheme of a typical plant, with notes on the operating peculiarities, precedes an account of product quality. The latest developments which enable by-product gypsum to be used as a raw material are discussed, with an indication of how the flow scheme is modified. A statement of feasible plant capacities is followed by requirements of raw materials, services, labour, etc., and finally some indication is given of capital costs."

Jan 1, 1969

By Y. Feng

Perovskite structured oxide 15% Y-doped BaCeO3 (BCY15) has been evaluated for use as proton conducting electrolyte in SOFC with propane as the fuel and Pt as both electrodes. Under the fuel cell conditions, BCY15 exhibited high proton conductivity and good cell performances. Propylene was detected as product at the anode outlet, and the product distribution suggests that propane dehydrogenation underwent competition with cracking to lighter hydrocarbons. Stability during cell performance tests showed that there was no obvious degradation for BCY15 electrolyte during operation of C3H8-O2 fuel cell.

Jan 1, 2005

By J. C. Hawkins

Determining moisture content and rate of flow of a solid product make measurement and control of dryers unusually difficult. This paper de-scribes a method of accomplishing this with readily made air-temperature measurements. The system can cope with changes in feed moisture and feed rate. It does not measure solids temperature. The system's application to several typical rotary dryers is described, and control schemes using feedforward techniques are explained.

Jan 1, 1971

By G. P. Demopoulos

"The recovery and separation of platinum-group metals (PGM) from primary and secondary materials currently attracts a lot of interest due to the high value of the metals and their increasing demand for high-tech applications. Thus, the traditional refining processes are gradually replaced by newer more efficient separation techniques such as solvent extraction and ion exchange. In this paper the classical and modern refining techniques are reviewed and the pertinent solution chemistry dictating proper processing strategies in each case is discussed. The technological advantages of the modern separation methods are emphasized and reference to the recovery of PGM from primary as well as secondary materials is given. INTRODUCTIONDue to their outstanding physicochemical properties, such as catalytic activity, conductivity and corrosion/oxidation resistance, precious metals now find extensive usage outside of the traditional jewellery and investment industries. The increasing use of precious metals in such areas as electronics and catalysis, as well as their increasing high value, has led to a growing interest in their recovery and separation from primary and secondary materials.Quantitatively the demand of platinum metals in the western world by area of application is described in Table I. Platinum and palladium represent 90% of the total demand, Rh and Ru 8% and the remaining is taken by Ir and Os. In terms of value the following were the average prices (US$/oz) of the metals in the second half of 1986: 500 Pt, 125 Pd, 1200 Rh, 650 Os, 400 Ir and 80 Ru. Due to these prices, exploration, mining, reclamation and refining activity were very high in South Africa, the biggest producer of Pt metals in the world, as well as in other areas: United States (Stilwater deposit), Canada (Sudbury, Marathon and Lac des Isles, Ontario; Kenly Lake, Quebec, etc.), Australia, Europe and elsewhere"

Jan 1, 1989

By V. Estrada, G. Aguilera

"Since the most of mineral processing are wet, and for more specific applications where it is necessary to increase the purity through leaching and / or concentration, the proper dispersion is the first, and perhaps more crucial stage in the whole chain of processing. This specific process is based on the formation of a dispersion or suspension of mineral, trying to make the mixture as homogeneous as possible, and with specific rheological conditions. Sometimes it is not enough agitation to make it happen, so that chemical additives are used as an aid. However, the addition of chemicals strongly alters the viscosity and other rheological properties of the suspension factor to consider for subsequent steps to ore beneficiation. In other hand, in a process where no chemicals used often employ large quantities of water to achieve dispersion. But if an efficient chemical agent, which optimizes said dispersion through a specific physicochemical effect on the particle surface is used, also it can generate rheological advantages, besides achieving rational use of water and increase the recoveries of the product main about also optimal costs. The aim of this work is to find the optimal rheological conditions for a dispersion of kaolin as study case, looking for stability, best disaggregation, viscosity and pseudoplasticity.To find the optimal additive, the evaluation parameters were: 1) Best degree of dispersion of the suspensions according to the analysis of the flow curve; 2) Best level of disaggregation of particle chemical analysis delaminated by Particle Size Distribution; and 3) Best thixotropic rheological parameters and pseudoplasticity. Finally the optimum additive as one that meets the best combination of parameters is proposed.INTRODUCTIONKaolin is a clay material formed by altering of feldspar composed mainly for kaolinite. Depending on the application, the kaolin as raw material must be refined and processed because the ores of clays contain usually a lot of impurities derived of its sedimentary source, such as feldspar, mica and quartz (Torres, et. al., 2011). According to the experience on the plant floor and the publication of several scientific papers, it is known that the dispersion is a crucial stage in mineral processing (Greene, Duke, & Hunter, 1965) (Raghavan, et. al., 2004), not only because of the disaggregation of particles, besides because of the humectation of them. Is clear that disaggregation of particles give to the suspensions rheological stability, and the humectation improves the effect of further processes like grinding or chemical treatment. The dispersion process involves making a suspension of the mineral with a solvent which is usually water, to obtain a homogeneous dispersion, with the aid of energy of stirring. Sometimes is not enough the agitation (even with high energy) for this to occur, so is necessary the use of dispersing substances which introduce ions and molecules as modifiers of chemical potential, forcing the molecules of the material to disperse. Sometimes their use even could affect the pH of the suspension in a non-desirable condition. (Flores, 2013)."

Jan 1, 2016

Research on alternative lixiviants for gold is ongoing; however few people have looked at complete flowsheets. Alternative lixiviants are typically applied at concentrations 50 to 100 times those required for cyanidation. The higher concentrations make lixiviant recycle a vital part of the process. In addition it is no longer feasible to rely on lixiviant destruction to produce lixiviant free clean water for recycle to the comminution circuit. Ausenco has worked with Barrick to integrate reverse osmosis into the thiosulfate RIL processing flowsheet that forms the basis of the plant upgrade currently being constructed at Barrick’s Goldstrike autoclave facility.

Jan 1, 2014

By G. Paillard, I. E. Puddington, A. F. Sirianni, F. W. Meadus

Experiments with some selected Nova Scotia coals and a single sample of American anthracite, reconstituted in granular form with lower sulphur and ash contents by spherical agglomeration methods, are described. The effect of different bridging liquids, grinding times, gangue depressents and modes of agitation on the final product are discussed. The application of agglomeration techniques as a means of drying wet coal fines is also noted.

Jan 1, 1968

By N. Tounsi

The use of analytical modeling of continuous chip formation in conjunction with orthogonal cutting experiments was presented in the open literature to identify the coefficients of material constitutive equation within the practical range of stress, strain, strain rate, and temperature encountered in metal cutting. Identification of reliable constitutive data was hampered by a lack of a reliable model for the prediction of the primary shear zone thickness that affects directly the effective strain rate field. An original analytical model to determine the primary shear zone thickness is proposed in this paper. It is based on the mechanics governing the material flow in the primary shear zone. Based on the distribution of the hydrostatic pressure and the forces measured from orthogonal cutting tests, the model that describes the thickness of the primary shear zone is derived. To validate the model, FE simulations of chip formation using DEFORM3D were carried out for different materials and cutting conditions. The results of the analytical model are in reasonable agreement with FEM results.

Jan 1, 2006

By Nessetech Consulting, L. A. Cisternas, E. D. Galvez, S. H. Kuan, L. H. Saw

"In Malaysia, there were two rare earths processing plants namely Asian Rare Earth (ARE) and the Malaysian Rare Earth Corporation Plant (MAREC) in Perak, which were operated until 1992 and were subsequently closed due to problems pertaining to disposal of large amount of radioactive waste. Recently, Lynas Advanced Materials Plant (LAMP) has become one of the largest rare earths processing plant in the world producing rare earth elements (REE) in Gebeng, Pahang. The primary raw material is lanthanide concentrate (LC) which is imported from Mount Weld mine in Australia and shipped to Malaysia. LC is produced from lanthanide ore after mining and mineral processing. The ore has a lower impact than Bayan Obo, Mountain Pass and adsorbed clay deposits, given the small footprint of the mine itself and the remoteness of the location. The type of ore being mined (rare earth phosphates: carbonatite, monazite) may have higher thorium content than bastnasite ore from the Chinese or American mines but still far below radiation concerns. This paper was written to review the processing flowsheet at the Lynas Advanced Materials Plant (LAMP), the environmental impact associated with the processing of the said ores and the sustainability of the operation.INTRODUCTIONRare earth minerals are one of a set of 17 minerals or chemical elements which consists of yttrium and scandium, as well as the 15 lanthanide elements (lanthanum, cerium, praseodymium, neodymium, promethium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium, and lutetium). Despite their importance, rare earth minerals rarely exist in economically viable concentrations and they are usually difficult to extract. Rare-earth minerals create strong magnets when added to magnetic elements such as iron, and are useful for the production of electronics systems as well as electric cars. They are also used extensively in automotive catalytic converters, fluid cracking catalysts in petroleum refining, wind turbines, phosphors in colour televisions and flat panel screens, displays for mobile phones and laptops, rechargeable batteries, and various medical devices. The elements are typically split into two subgroups: the cerium sub-group of ‘‘Light’’ rare earth elements (LREEs) which includes La to Eu and the yttrium sub-group of ‘‘Heavy’’ rare earth elements (HREEs) which include the remaining lanthanide elements, Gd to Lu, including yttrium (Gupta and Krishnamurthy, 1992; Jordens et al., 2013; Trifonov, 1963). Scandium, however, when it is classified as a rare earth element, is not included in either the LREE or HREE classifications (Gupta and Krishnamurthy, 1992; Jordens et al, 2013). Half of the world’s 110 million tons of reserves exist in China while other sizable deposits are found in Russia, United States, Brazil, India, Australia, Canada, and Greenland. The countries known to be actively mining REE are China, Russia, India, Brazil and Malaysia (Hao et al., 2015). Among these countries, China has the largest REE production, accounting for more than 93% of global supply (Yap, 2015). The critical metal report (Moss et al. 2011) listed 14 economically vital raw materials that are prone to supply disruption and concluded that supply disruption would threaten the goal for cleaner transport and sustainable energy since rare earth metals are used in products using green technology, such as hybrid/electric vehicles, carbon capture systems, wind power generation, low-energy lighting, and energy efficient flat-screen displays."

Jan 1, 2016

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By M. Krasowska, K. Malysa, M. Krzan

The paper presents fascinating, in our opinion, observations on mechanism and course of processes occurring during bubble collision with hydrophobic and hydrophilic solid surface. Hydrophobicity of particle surface is a necessary condition for the particle attachment to bubble. We have observed that even in the case of such hydrophobic solid surface as Teflon, the bubble attachment didn't occur at first collision. In distilled water the bubble bounced a few times without attachment. Influence of a-terpineol and n¬pentanol on bubble local and terminal velocity and the phenomena occurring during bubble collisions with hydrophobic and hydrophilic solid surfaces was studied. Bubble collisions with the solid surfaces were monitored and recorded using the high-speed (1182 frames per second) camera. It was found that in distilled water the velocity variations of the "approach-bounce" cycles were identical for Teflon and glass. Four distinct "approach-bounce" cycles were detected both at Teflon and glass surfaces. Moreover, the amplitude and frequency of the velocity variations were identical on collisions with the hydrophobic (polished) and hydrophilic surface. There was no immediate three phase contact formation, with the hydrophobic Teflon surface, what we found really astonishing. Roughness of Teflon surface seems to be important parameter, which affects probability of the bubble attachment as a result of a presence of micro-and/or nano-bubbles at the surface. It was detected that the presence of the micro-bubble affected attachment of the colliding bubble even in distilled water. Presence of a small amount of a-terpineol or n-pentanol affects dramatically the bubble velocity, but their role in mechanism of the bubble attachment needs further study.

Jan 1, 2004

By P. J. Finnis

This paper describes the use of wire rope on open-pit mining equipment, giving specifications and examples of the performance achieved. Installation methods are also discussed, making the paper of considerable practical use to mine operators.

Jan 1, 1973

By Jeremy G. Berg, James B. Mulligan

"There is a very small fraction of wireless experts in the world with experience in underground installations and an even smaller fraction that have experience specific to building mine shafts. This is why in 2009, Redpath created its own system to meet the demands specific to shaft construction. Today, after a dozen shaft installations and several design iterations, Redpath has the expertise and experience required to implement a proper wireless system in any shaft configuration.This document will explain multiple proven wireless communication designs optimized for shaft construction and suitable for permanent use. This includes line of sight installations up to 1200m, short range mesh networks, and the latest patent pending Integrated Leaky Feeder Mesh Network. Additionally, this document will explore the lessons that Redpath learned in its effort to interconnect the people and tools needed to build a mine shaft.INTRODUCTIONAfter a decade of research, several design iterations and a dozen application examples, Redpath has resolved two wireless network architectures to best serve mine shaft construction projects.The long range line-of-sight (LOS) wireless network is the most cost effective and easiest to install, but requires an unobstructed line of sight between the working area and the shaft collar. As such, long range LOS is best suited for ventilation shafts or during the first phase of shaft sinking, before the shaft is equipped.Alternatively, a mesh network uses radios installed at pre-determined intervals in the shaft and on each conveyance. A wireless mesh uses antennas to bridge intervals between shaft radios, whereas Redpath’s integrated leaky feeder mesh network (patent pending) bridges these intervals with radiating cable, commonly referred to as a “leaky feeder” cable. Both of these mesh configurations can provide continuous reception for hoist conveyances travelling in shafts without line-of-sight, making them ideal for shaft equipping and even permanent installations in both mine shafts and lateral drifts.BACKGROUNDHoist operators receive operating commands using what are commonly referred to as “bell signals.” These instructions are delivered in a series of coded pulses on a spring returned pull cord or push button that is typically hardwired back to the hoist operator’s control room from one of many locations in the mine shaft. During the construction phase of a traditional mine shaft, a worker riding inside the sinking bucket would have to reach out to a pull cord installed on the shaft wall to send a stop command to the hoist operator. Today, Redpath’s modern shaft sinking projects use fully enclosed personnel carriers to protect the workers riding inside, specifically preventing workers from reaching out into the shaft while the hoist is in motion. The enforcement of this safety feature on all shaft projects in 2008 forced the engineering group at Redpath to find a suitable wireless solution for hoist communication to facilitate shaft construction.THE IDEAL COMMUNICATION SYSTEM FOR MINE SHAFT CONSTRUCTIONIdeally, the shaft communication system should not transform the tools to which the miners have grown accustomed. It should support the push-to-talk functionality of traditional VHF handsets and the standard belling system that has been used for decades. Additionally, it should be able to support a vendor independent framework upon which new devices and features can be added. The following paragraphs summarize some of the important requirements Redpath has identified.Support for voice transmission: Low latency is critical to prevent jitter during voice transmissions. The system must be compatible with commercially available mobile handsets and support several simultaneous conversations with the ability to broadcast a voice message to all users on a select channel using a “push-to- talk” microphone and loudspeaker.Transmission of PLC data: Low latency is required to"

Jan 1, 2019

By Euler De Souza, J. Daniel Stinnette, Julian Varaschin

"This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and of electric equipment and examines how they can be applied in determining reasonable ventilation rates for Tier IV compliant diesel equipment and for electric equipment operating in mining environments. Airflow calculations for modern diesel-powered equipment and for electric equipment are more complex and must be based on a combination of factors that are unique to each mine. Methodologies for ventilation rate determinations for each case are proposed in this paper.INTRODUCTIONTraditionally, airflow requirements for production and support equipment operating in underground mines have been determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations or determined empirically from known quantities. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is still a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. The question remains, what ventilation rates should the ventilation system designer apply for modern diesel equipment?Also, given the ongoing development of grid/battery-electric equipment and active construction of fully electric mines, it has become critical to determine adequate airflow rates per brake kilowatt of electric engine power. One of the most important criteria for determining ventilation rates for electric equipment is the amount of heat they generate, as this is the most significant emission produced by electric equipment (which do not produce exhaust gases or particulates). Therefore, ventilation rates required to dissipate heat from electric equipment must be suitably determined for all electric vehicle fleets operating in underground mines."

Jan 1, 2019

By Lesley Hymers

First Nations Natural Resources Youth Employment Program PDAC Mining Matters ? Charitable organization ? Provide education to students, teachers, and the public about rocks, minerals, metals, and mining ? Provide current information and offer exceptional educational resources that meet provincial Earth science and geography curriculum expectations First Nations Natural Resources Youth Employment Program ? Provide instructional development workshops for educators who are teaching Earth science and geography ? Since 1994, reached more than 400,000 students, teachers, industry representatives, and members of the public

May 1, 2009