Search Documents

By Claude Bazin, François Robichaud

"The control of the operation of semi autogeneous grinding (SAG) mills is mainly achieved through adjustments of feed rate, water addition and speed of rotation. With the introduction of image based sensors it is possible to have on-line measurements of the size distribution of the ore feeding a SAG mill. This information could be used for the development of a control strategy to regulate a SAG mill feed size distribution to a set-point. The control of the size distribution is carried out by adjustment of the speed of the ore extractors underneath the ore stockpile. The potential and difficulty associated with the implementation of such control are assessed using a multivariable statistical analysis of data collected from the operation of the grinding circuit of the Agnico-Eagle Goldex mine in Val d’Or, QC. A control strategy for the ore feed size distribution is assessed using a simulator of the ore stockpile operation.INTRODUCTIONThe popularity of autogeneous (FAG) and semi autogeneous (SAG) grinding mills has been increasing over the last 20 years (Napier Munn et al., 1996). These mills use the ore or a combination of ore and steel balls as the grinding media. Since the ore is used as a media for the size reduction the mill ore feed size distribution impacts the performance of the mill. Several papers were recently published on this subject (Dance et al.,2011; Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011) showing the advantages of preparing the feed size distribution to maximize the circuit throughput or mill efficiency (Wennen & Murr, 2011; Dance & Valery, 2011; Allaire et al., 2011). With the availability of particle size sensor based on image analysis of the ore on a conveyor (Partanen et al., 2001; Bobo et al. 2004; Edwards et al., 2002; Wei & Craig, 2009) it is possible to control the size distribution of the ore feeding autogeneous or semi autogeneous mills (Partanen et al., 2001).This paper describes a method to control a size distribution index to a set point via the manipulation of the speed of the extractors that withdraw the ore from the stockpile feeding the grinding circuit. The paper consists of 4 sections. The first section describes the considered grinding circuit. A statistical analysis of the collected data on the grinding circuit is presented in the second section. This analysis demonstrates the necessity of using real-time adaptation mechanisms to develop a control strategy for the size distribution of a grinding circuit. The third section describes the method used to simulate the ore stockpile operation and the last section describes the preliminary development and assessment of a control strategy of size distribution of the ore feeding a SAG mill."

Jan 1, 2013

By J. A. Meech, G. R. Baiden

"A dynamic simulation of a mine-mill complex has been conducted using networked microcomputers (IBM PC/AT and IBM PC/XT). These models allow simultaneous operation of an open pit using shovels and trucks, a primary crusher, and a secondary crushing plant. Each process transmits information via the network, linking all operations together. The effects of blasting, ore quality, equipment utilization and configuration on productivity can be studied either interactively or from a report listing at the end of each shift. Programs are menu driven leading the user through the decisions required in day to day operations. The mine-mill simulator is currently being used as a teaching tool at Queen's University to provide senior mining and mineral processing engineering students with an experience and appreciation for the operating problems across the mine-mill interface. The need for coordination and close communication between the mine and mill can be aptly demonstrated using these models. The simulator could be used to contribute to the training of operating personnel in a real mining operation. INTRODUCTIONThis paper describes a computer simulator that is capable of showing the interactions and operating strategies between a mine and a secondary crushing plant. The simulator uses two models developed at Queen's University; one for open pit mining and the second for secondary crushing. PITSIM is a dynamic shovel/truck haulage model origin2lly developed by P.D.D. Chick (1) and K.G. Fytas (2) to solve shovel/truck scheduling problems. CRUSHSOFT is a dynamic secondary crushing plant model developed by R.J. Tucker (3) and C.A. Harris (4) to study alternative operating and control strategies in a crushing plant."

Jan 1, 1987

By Roger Payne, John R. Goode, Feng Gao, James Brown

The Eco Ridge deposit is located in the Elliot Lake mining camp in Northern Ontario, Canada. Between 1955 and 1996, the area produced more than 138,000 t (300 million pounds) of U3O8 and very significant amounts of thorium and heavy rare earths. Based on the NI 43-101 Preliminary Economic Assessment by Roscoe Postle Associates (RPA) dated June 2012, and the economic review by RPA as announced in Pele Mountains’ Press release dated September 12, 2013, the Eco Ridge Mine Project would extract and process 46 Mt of material to produce about 19,000 t (42 million pounds) of U3O8 and about 65,000 t of rare earth oxide (REO) over a 14-year life. This paper discusses process optimization studies including beneficiation and hydrometallurgical testwork. The proposed modified flowsheet includes the flotation and processing of 1) a pyrite concentrate, 2) a dominantly light rare earth elements (LREE) concentrate, 3) a concentrate containing most of the balance of the uranium and heavy rare earths (HREE), and 4) a relatively inert tailings.

Jan 1, 2014

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By Paul J. Sylvester, Yeonuk Choi, Mike Nelson, Louis J. Cabri, Mike Tubrett

"The development and characterization of sulphide standards containing as many as seven precious metals has increased the efficiency and comprehensiveness of micro-analyses for deportment studies using laser ablation microprobe inductively coupled plasma mass spectrometry (LAM-ICPMS). Because trace precious metals occurring in solid solution or as sub-micron inclusions in sulphides, arsenides, and sulpharsenides are often heterogeneously distributed, a significantly large number of analyses are required. Using well-prepared samples it is possible for up to 120 analyses per day, far more than by other comparable methods. Examples will be discussed from projects focused on the deportment of Au and the platinum group elements (PGE).INTRODUCTIONBecause gold and the platinum-group elements (PGE) occur as both discrete minerals and in trace quantities in a variety of minerals (mostly sulphide, arsenide, and sulpharsenide minerals), specialized trace analytical methods were developed and applied to determine the deportment of precious metals in ore deposits, requiring sensitivities ranging originally from about hundreds to presently tens of ppb for individual precious metal or less.In mineralogical studies, micro-analytical techniques such as the electron microprobe were first applied to obtain analyses for major elements in about 1959-60, but as the instrumentation improved early attempts for PGE in potential carrier minerals indicated that reasonable levels of detection (LOD) were of the order of 300-400 ppm, depending on analytical conditions, X-ray spectral lines, and mineral matrix (e.g., Cabri and Laflamme, 1976). Eventually, the lowest detection levels by electron probe micro-analyses (EPMA) obtained for some PGE were of the order of 10s of ppm using high accelerating voltage and current for extended measuring time on peak and background (Gervilla, Cabri, Kojonen, Oberthür, Weiser, Johanson, Sie, Campbell, Teesdale and Laflamme, 2004)."

Jan 1, 2010

By O. P. Garg

"The Iron Ore Company of Canada (IOC) operations in Labrador and Quebec, in Canada, is among the largest openpit mining complexes on a world wide basis. Since the 1981-82 recession, IOC has embarked on a comprehensive cost reduction and productivity improvement program in order to survive in the world iron ore market.This paper will outline the approach used in prioritizing the cost reduction items.IntroductionMuch of the mining industry in North America is in a crisis state. Most producers are operating at production levels well below capacity, some have been merged or sold, while others have been mothballed or closed permanently. For many of us still operating, the future is uncertain. Despite the many cutbacks and closures, there is still an abundant supply of minerals in the world market and there is almost no hope for any relief on price pressures on most mineral commodities in the near future. The Iron Ore Company of Canada (IOC) operates an iron ore mine, a concentrator and a pellet plant known as the Carol Project located in Labrador City, Newfoundland. This concentrator and the pellet plant have the annual capacity to produce 20 million and 10 million tons respectively. A company owned and operated railway links this operation with the dock terminal facilities in Sept-Iles, Quebec.In the past decade the Iron Ore Company of Canada has been one of the largest producers of iron ore products in the world. Its pellets and concentrates as well as natural ores were sold in North America, Europe and the Far East. In 1981-82, sales, particularly in North America, went into a serious decline. For almost 30 years, the gospel IOC preached to employees was ""production, production!"" There were many innovations, and millions of dollars were spent on the biggest and best equipment, on research and development, on training and developing employees."

Jan 1, 1987

By L. S. Urbanoski

This presentation describes a major modernization project at the Geco concentrator. The objectives of the program were to replace obsolete flotation equipment and upgrade process controls.Noranda Minerals Inc. — Gecc Division is located at Manitouwadge in Northern Ontario. The community is situated north of Lake Superior approximately equidistant from Thunder Bay and Sault Ste. Marie.Milling operations began in September, 1957. The mill processes a complex base metal ore by differential flotation techniques to produce copper, lead and zinc concentrates. To date some 43 million tons have been milled, qualifying Geco as a rather major base metal deposit.II. BACKGROUND:The Geco concentrator was designed and constructed in the mid 50's. A number of features specific to a concentrator of that vintage provided the justification for the modernization efforts described herein.Firstly, the mill was constructed without any instrumentation, not even pneumatic controls. Solid state electronics, computers and related instrumentation were unheard of, or rather primitive by today's standards.Secondly, some of the major equipment, in particular the flotation equipment, did not compare favourably to that in use today. MacIntosh flotation machines (more commonly known as Mac cells) were installed at Geco. These cells were prevalent in a number of concentrators built by Noranda, including Quemont Mining Corporation Limited, Gaspe Copper Mines Limited and Noranda — Horne Division. The Mac cells were used for copper and zinc rougher and scavenger operations. Some units were also installed for a pyrite recovery circuit that was never operated. In total, 104 Mac cells were installed in the main flotation area of the concentrator.

Jan 1, 1987

By Eduardo Nunez, Asim Tuzun, Dan Graffi, Glenn MacPherson

"In preparation for the milling of a new nickel and copper mine ore, Nickel Rim South, Xstrata’s Strathcona Mill is undertaking numerous process improvement projects. Within the grinding circuit, several projects are under development and an automated grinding control strategy, consistent with the operating objectives, was identified as a key requirement. The grinding strategy is to maximize the throughput (quantitative objective) while maintaining the cyclone overflow within specifications (qualitative objective).This paper describes the implementation of a robust grinding control strategy using the existing control system. The implemented controls maintain the cyclone overflow density at the desired target, while continually optimising the rod mill feed rate to allow maximum throughput. This approach has the added benefit of improving the stability of the rougher flotation circuit down stream of the grinding and improving energy efficiency of the rod and primary ball mills. This paper discusses the comparison of the before and after the implementation of results.INTRODUCTIONThe grinding process is a size reduction operation used in the mining industry to liberate the valuable minerals from the gangue. Grinding is one of the most important and expensive processes in a concentrator (Xi-song, 2007; Pomerleau 2000; Najim 1995), often accounting for around half of the total operating costs in base metal concentrators (Wills, 1990), which has led to a focus on development and implementation of control and optimisation strategies. The grinding process prepares the ore for the subsequent concentration step, which for sulphide base metal operations, is predominantly flotation. The performance of the concentration (flotation) is very much determined by the feed characteristics of the slurry coming from grinding. The valuable minerals recovery process in flotation is very much influenced by the grinding process and the liberation of the desired minerals from the gangue minerals (McIvor, 1991).The true objective of grinding is to obtain a proper liberation of the minerals as defined by a particle size distribution referenced typically by d80 (80% passing size of product). Besides achieving the desired mineral d80 size, it is clearly desirable to produce as narrow a size distribution as possible to squeeze the maximum amount of the mineral value into the highest recovery region (McIvor, 1991). This is an important criterion for the mill in economically optimizing the grade and recovery for the concentrate product. It is important not to over or under grind, while keeping the specific comminution energy as low as possible (Nunez, 2005) to achieve the target liberation. In other words, maintain an optimal throughput depending on the ore conditions to the capacity of the grinding mills, while providing the flotation process with a constant and narrow size distribution, at a cut size selected to meet the metallurgical requirements (Bascur, 1991)."

Jan 1, 2009

By M. H. Moys, J. A. Finch, A. R. Laplante

"A detailed review of ball milling circuit control practices in industry has been carried out. Based on fundamental process performance objectives, a standard system for base-level control of most ball mill installations is presented. This system is simple, inexpensive, and provides the major economic benefits available from contemporary automatic control technology.Value Analysis of Grinding OperationsValue analysis (or engineering, or management), originally developed by Lawrence D. Miles of the General Electric Company (1), focuses on the identification of value (product or process worth versus cost) and provides a systematic procedure for its improvement. A recent research and development project involving the application of the principles of value engineering to grinding operations has provided a basic technoeconomic model of grinding processes (2). The functional objectives of the ball milling process and the means to achieve value based grinding circuit control originate from this study.The Need for Grinding Circuit ControlThe economic effectiveness of a process is determined by the quality or value of the product and the related processing costs. If the inputs (both the raw feed and the applied processing work) are absolutely constant, the product characteristics and the process efficiency will be determined only by the engineering design. The need for and degree of process control is therefore determined by the nature of variations or upsets in the process inputs, and the extent to which these effect product value and operating costs."

Jan 1, 1988

By Keith Merriam, Jim McDonnell, Peter Radziszewski, Rob Rotzinger, Ian DeHart

"Taseko Mines Limited Gibraltar copper-molybdenum mine recommenced operation in 2004 with the initiation of a series of development projects to increase throughput capacity as well as modernize the mine.In the second staged development project, a VTM-1250-WB regrind mill was selected to replace the existing conventional ball regrind mill to achieve a target grind size of 80 % passing 45 µm. In the third staged development project, a second VTM-1250 regrind mill was selected for installation in Concentrator #2, to match the existing Concentrator #1 Vertimill. This resulted in approximately 25% spare regrind capacity in the Concentrator #2 design, complete spare parts interchangeability and potential future expansion capacity to 50,000 t/d with no circuit upgrades.In this context, a study was initiated to assess not only the performance of a Vertimill grinding circuit processing a copper concentrate to a particle size of 80% passing 17 µm but also to provide Taseko’s New Prosperity project specific design information for grinding to particle sizes below 80 % passing 25 µm.The objective of the work described in this presentation was to explore Vertimill ultrafine (sub 100 µm) grinding test methodologies at both the lab and pilot scales, compare the scale-up data with operational data from the VTM1250 at Gibraltar Mines and subsequently apply this information to particle sizes down to 80% passing 17 µm. The presentation will describe the results obtained preceded by a description of the Gibraltar regrind circuit historical operation and operational performance as well as a description of the Vertimill technology.INTRODUCTIONTaseko Mines Limited is a mining company headquartered in Vancouver, British Columbia, Canada. In addition to mining development projects for copper, copper-gold, gold, and niobium properties, Taseko Mines is seventy-five percent owner and the operator of the Gibraltar Mine near Williams Lake , British Columbia. Taseko Mines Limited’s Gibraltar copper-molybdenum mine recommenced operation in 2004 with the initiation of a series of development projects to increase throughput capacity as well as modernize the mine.Metso is a leading process performance provider, with customers in the mining, oil and gas, and aggregates industries. It has corporate headquarters in Helsinki Finland, offices in 50 countries and manufacturing facilities on five continents. Amongst other types of equipment and services, Metso designs and manufactures VERTIMILL® (VTM) Grinding Mills."

Jan 1, 2015

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By Wendy L. Naysmith

This paper deals with the various options considered and factors that influenced the final selection of the headframe, shaft layout and hoisting systems required at the Impala No 16 Shaft in order to hoist both the required 3 Mt of ore per annum, and transport men, material and equipment between the surface and the underground workings to a depth of 1640 m. The layout and construction method used for what is at present the world?s tallest concrete headframe is discussed together with the integrated hoist room foundations designed to suit multiple mechanical and electrical hoist supplier?s solutions. The mechanical components of the two tower mounted 6,5m 4 rope Koepe hoists and deflection sheaves and their layout is dealt with in detail. Various features of the bearing type, brake units and brake control system are also discussed. Installation of the mechanical and electrical hoist equipment in the headframe took place during the sinking phase of the project and placed severe restrictions on the use of the heavy lifting facilities. This required a well-managed and systematic approach to delivery of the hoist components and associated equipment, as well as close co-operation between all contractors on site.

Oct 1, 2010

By Jennifer Pell

Dunsmuir Ventures? Nanuq diamond project is located approximately 250 km northeast of Baker Lake and 170 km north of Chesterfield Inlet. It occurs at the intersection of the Wager Bay shear zone with the Keewatin Arch, a major long-lived crustal uplift. The newly discovered diamondiferous kimberlites at Rankin Inlet, Repulse Bay and on Melville Peninsula also occur along this arch. Kimberlite indicator mineral (KIM) sampling has outlined a distinct KIM train more than 35 km long and 6 km wide. Geomorphological studies, boulder displacements and dispersion of magnetite in tills suggest that glacial transport distances were on the order of 4 to 6 kms only. The presence of multiple sources within the main Nanuq indicator train would account for its length and breadth. A second train has been located on the west central part of the property and anomalous concentrations of KIM occur elsewhere. Pyrope garnets (G9?s and G10?s), diamond inclusion field (DI) eclogitic garnets and DI chromites were confirmed by microprobe analyses. Clinopyroxene thermobarometry indicates a cool geotherm, approximately 35 mW/m2, and that mantle within the diamond stability field was tapped. An aeromagnetic survey has identified a number of anomalies. Those with down ice KIM support will have ground geophysical follow-up and will be tested in a spring 2004 drill program. Dunsmuir is optimistic that this will lead to the discovery of a new kimberlite cluster on the Nanuq property.

May 1, 2004

By Neri Roux, Chris Budgell, Allan Cramm, Leo Cheung

"Anaconda Mining Inc. is investigating potential improvements and expansions to their operating plant located on the Baie Verte Peninsula in Newfoundland. An extensive batch and continuous bench scale testing program was launched to investigate the efficiency of cyanide destruction under different conditions in order to improve tailings handling. The primary objective of the cyanide destruction study was to apply new technologies to develop a novel cyanide destruction system.Effluent and slurry from Anaconda Mining Inc.’s Point Rousse Project was received at RPC where test work was conducted. Various sodium metabisulfite (MBS) dosages were evaluated and the use of utilizing ozone and ultra violet (UV) light to oxidize cyanide was investigated. All the data was evaluated and mass balances were compiled to develop several flowsheets. Overall encouraging results were found using a combination of ozone and MBS.IntroductionAnaconda Mining Inc.’s Point Rousse project includes an operating gold processing plant located on the Baie Verte Peninsula in Newfoundland which is in the process of improving and expanding. This plant comprises of milling and flotation followed by cyanide leaching in order to extract the gold. The residue from cyanide leaching is filtered by drum filters prior to being clarified for the Merrill-Crowe process. Once the gold has been recovered by the Merrill-Crowe process the effluent is filtered by filter presses and the resulting filtrate as well as the solids from the drum filters are detoxified prior to being pumped to the tailings pond along with the flotation tailings.The entire process is very dependent upon the efficient destruction of cyanide in the effluents and successful tailings handling. Substantial amounts of effluent are delivered to tailings ponds after gold extraction which could create environmental problems if the regulations are not met. Environmental regulations stipulate that final effluents contain no more than 1 mg/L Total CN.The detoxified tailings of the Point Rousse project are produced by the INCO SO2-Air circuit depicted in Figure 1. These detox tailings contain 10 mg/L Total CN at that point of the circuit and this was selected as the target to be matched while reducing overall MBS consumption rates from 3.2 g/L per minute. Prior to detoxification, the filter press tailings contain 520 mg/L Total CN while the drum tailings contain 29 mg/L Total CN."

Jan 1, 2017

By Andy Lemay

Vale (previously known as CVRD) is: ? The second-largest mining company by market capitalization (NYSE:RIO) ? Headquartered in Brazil ? Global workforce of over 100,000 employees including outsourced workers. Vale Inco Limited is a wholly?owned subsidiary of Vale Vale Inco Limited ? is based in Toronto, Ontario Canada: ? Operations and Projects in 20 countries ? Marketing Network extending to 40 countries ? Over 12,000 employees worldwide ? Last years sales of US $8 Billion

May 1, 2008

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

A series of fault slip seismic events have occurred at Garson mine. The events have occurred during development advancement exposing faults, after the extraction of single stopes due to mining induced stress change, and due to time effects after delays of many days during which no mining had been conducted. This paper discusses the study completed consisting of a global or holistic approach aimed at mitigating some of the risks associated with the structurally controlled rockbursts at Garson. Background Garson mine is located in the south east area of the Sudbury Basin (Ontario, Canada). Mining occurs in two main ore bodies (the #1 Shear and the #4 Shear) which are copper-nickel-sulphide and occur within shear zones that (as well as the ore bodies) strike approximately east-west and dip steeply south. From the north (footwall), lithologies progress (Figure 1a) from norite (NR), to greenstone (GS), and finally to meta-sediment (MTSD). A generally WNW-ESE striking, bifurcated sub-vertical dyke of olivine diabase (OLDI) cuts the series. The current active mining block at Garson is between 4700L and 5100L (levels denote depth in feet below surface).

May 1, 2009

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009