Search Documents

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

"The Dumont deposit is a large (1066 Mt probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the deposit through pre-feasibility. And updated, revised pre-feasibility was released in July 2012.The disseminated nickel sulphide and alloy mineralization is hosted within the serpentinized dunite subzone of the Dumont Sill; a differentiated, pervasively serpentinized, ultramafic sill of komatitic affinity. Pentlandite, heazlewoodite and awaruite are the dominant nickel-bearing, metallic phases and can be recovered by conventional methods (flotation, mag separation). Non-recoverable nickel is also present within the silicate matrix of the serpentinized dunite and is locked in serpentine (Fe and Mg-rich variants) and minor olivine.A detailed mineralogical program including 1097 QEMSCAN® samples and 4300 electron microprobe points were undertaken to increase the understanding of the nickel deportment in the various recoverable and non-recoverable phases in a spatial context across the deposit. Eighty-three (83) metallurgical tests performed under a standard procedure have linked the mineralogy to metallurgical performance. This has allowed the creation and modelling of geometallurgical domains on a block by block basis to understand the recovery variation and metallurgical performance throughout the deposit. Understanding the spatial variability of Ni deportment in recoverable and non-recoverable phases through mineralogy is the key to understanding metallurgical performance thus, unlocking the value of the Dumont deposit and other large tonnage low grade ultramafic nickel deposits."

Jan 1, 2013

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

By Manuel Sanchez, Marcial Medina, Matt Hurley, Hugo Granados, Pramod Kumar, Raj Rajamani, Jose A. Delgadillo

"Large-diameter ball mills have traditionally used steel liners—steel being a highly durable material that can be shaped into any desired geometry, among which the double-wave has been the preferred design. Such a design produces a purely cascading charge motion, which is ideal for the shearing action needed to produce a finer product. Today, however, rubber liners, which have been in existence for over forty years, are now preferred over traditional steel, largely because they weigh less and are easier to maintain. In this paper, we show the operating data from the Hudbay Minerals’ Constancia Mine, wherein the liners on a 26-by-40-foot mill were changed from conventional steel liners to PolyStl™ liners. It is then shown that this change reduced the amount of energy consumed whilst being able to maintain previous grind and throughput levels. The design is verified via discrete element simulations.IntroductionThe Constancia Mine (“Our Business: Peru,” 2016) is located in the southeastern Andes of Peru, at an elevation of approximately 4,200 m. It can be accessed via the CU-126 road, about 95 km from the town of Espinar in Espinar Province. The mine also contains both the Constancia and Pampacancha deposits in the Province of Chumbivilcas. Hudbay Minerals, Inc. acquired the mine in 2011, through the purchase of Norsemont Mining, Inc. and currently retains sole ownership of the property. Production of the Constancia Mine began in 2014, with commercial production levels being achieved in April 2015.The Constancia and Pampacancha deposits primarily include hypogene, supergene, and skarn ores. The Mine’s main products, however, are copper concentrate, with silver contents, and molybdenum concentrate. These mineral reserves are expected to last approximately 22 years. Constancia’s open-pit mine supplies a processing plant that is designed for 81,900 metric tons per day of throughput. Average annual copper production is estimated to be 82,000 mT (contained metal in concentrate). Actual plant production can be found in Table 1."

Jan 1, 2017

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By A. H. Marquis

Since the start-up of its first Direct Reduction Module in April 1973, S1DBEC has produced over 2 million tons of prereduced iron. During this period, SIDBEC has acquired comprehensive experience in the operation of the direct reduction process and at the same time has learned to recognize the characteristics that the oxide should have to constitute an adequate feed for the process. A comparison is made as to the design and operation of the two direct reduction units now operating at Contrecoeur, Que. A description is given of a method of evaluation of a direct reduction unit, which takes into account the main process variable sand which permits comparison ofthe results on a daily basis. The paper defines the characteristics that the iron oxide and the prereduced iron pellets must have to meet the specific requirements of the direct reduction and the electric arc furnace processes. A simple model makes possible a rapid evaluation of the technical and economic effect related to the use of a given raw material. Finally, the paper outlines the advantages of prereduced iron in the steelmaking process and on the quality of the steel products.

Jan 1, 1979

By Eric Konigsmann

"The Pogo project is located on the Goodpaster River, 38 miles north of Delta Junction in east central Alaska. Sumitomo Metal Mining and Teck Corporation are planning to develop a 2,500 ton per day underground mine and mill at Pogo. A preliminary resource of 5.5 million ounces of gold has been identified in two flat lying lenses. An underground adit has been developed to facilitate underground drilling of the deposit and to provide samples for bench and pilot scale metallurgical testwork.Flowsheet development included the evaluation of several processing options. The final flowsheet selected includes SAGhall mill grinding, gravity concentration with intensive cyanidation and direct electrowinning, sulfide flotation with ultrafine regrinding, and cyanide leaching and CIP gold recovery from the flotation concentrates. Flotation tailings will be filtered for placement in a dry stack storage facility or disposed of as paste backfill underground. All of the CIP tailings will be disposed of underground as paste backfill. A pilot plant was carried out to evaluate the proposed flowsheet described above and to confirm the gravity recovery predictions.Great care was taken in the development of the flowsheet and site layout concepts to mitigate the environmental impact of the proposed operation. An overview of the site water management concepts is presented and the impact of water issues on the process flowsheet is discussed."

Jan 1, 2002

"In mining operations, it is widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In this paper, an integrated solution framework for reducing process variability, increasing process efficiencies and maximizing plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis “gap” evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.INTRODUCTION The changing landscape of gold mining and processing presents many challenges that threaten sustainability of existing (marginal) operations as well as deter investment in new projects. As existing “shallow” ore resources become depleted, mining operations are increasingly treating low-grade ores with complex and randomly variable mineralogical characteristics. For example, in South Africa, historically one of the major gold producers, the average grade of ore treated has been decreasing from averages above 4.5 – 5 g/t to current grades averaging less than 3 g/t within a decade (Chamber of Mines, 2012). Moreover, lower tonnages are being treated as a result of the narrowing of the available resource base. Also, the regulatory framework has tightened over the years due to heightened concerns on the safety, health and environmental impacts of mining and related activities."

Jan 1, 2014

By P. J. Mehrfert

"Recovery of mineralized coarse particles is notoriously low in conventional concentrators that treat copper porphyry ores. The application of coarse particle flotation techniques has the potential to achieve comparable metallurgical performance at significantly coarser primary grind sizings. ALS Metallurgy has been conducting both internal research and commercial test programs to investigate the potential of Eriez HydroFloatTM technology on copper sulphide ores. Test data indicates that significant improvements in the recovery of copper sulphide bearing particles between 200µm to 850µm can be achieved using Hydrofloat technology compared to conventional flotation techniques. This paper summarizes the results from a selection of test programs that includes recovery by size data from both conventional flotation and HydroFloatTM tests. An explanation of the apparatus and test procedure will be given. Mineralogical analyses of the test products and characteristics that limit metallurgical performance will be discussed.Description of Apparatus and Test ProtocolThe HydroFloatTM laboratory cell is a clear plastic column with an internal diameter of 14 cm. Water and air are introduced to the cell through a circular manifold located in the lower portion of the cell. The cell has a conical bottom which directs slurry to a pinch valve that controls the discharge of tailings. Feed solids are introduced to the upper portion of the cell in slurry form. The cell is operated in a manner such that the manifold water creates a teeter bed zone of suspended solids in the middle portion of the cell. Tailings exit the bottom of the cell at a high pulp density, and most of the introduced water overflows the top of the column and is collected in a launder. Particles with a hydrophobic surface may attach to air bubbles that percolate through the teeter bed, rendering them sufficiently buoyant to be transported to the overflow launder.Three significant features of this arrangement enhance the potential to recover coarse, low grade particles by flotation techniques. Firstly, the hindered settling conditions created by the rising column of water allow coarse particles to become buoyant once attached to a modest sized air bubble. Secondly, the flow conditions within the cell are relatively quiescent compared to a conventional flotation cell that utilizes an agitator. This allows particles that have limited hydrophobic portions of their surface, due to a low content of exposed sulphide mineral, to maintain a somewhat fragile attachment to air bubbles long enough for successful recovery to the overflow. Finally, the absence of a froth phase at the top of the cell allows particles attached to air bubbles to immediately exit the vessel, reducing the potential to drop back into the pulp phase as bubbles burst or coalesce."

Jan 1, 2017

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

By N. Shi, T. G. Joseph

The design of dippers for cable shovels has essentially remained unchanged for the last 100 years. In the past 10 years, shovel manufacturers have started taking another look at dipper design, resulting in changes that have borne models from major manufacturers that address some of the wear conditions and material retention problems that dominate maintenance and operational costs. However, with the exception of added lateral curvatures to the front and corners of the dipper, the geometry is essentially unchanged. This paper looks at the criteria that have resulted in the first new cutting dipper design in a century. The design is based on kinematic considerations, reflected in a revolutionary geometry that matches the range of motions of the shovel, designed to minimize wear, impact loading and power required to dig, thus maximizing productivity for a minimum energy requirement. The shape configuration is such that the weight of the dipper is reduced through wall thickness, enabling a larger capacity dipper to be conceived for the same shovel. Benefits are reflected in reduced operational and maintenance costs and increased productivity.

Jan 1, 2006

By Guy Chevalier, Jean-Guy Chartrand, Louis Barrette, Daniel Michaud, Michel Fortin

"COREM has developed, specifically for the mineral industry, a mobile laboratory using the Laser-Induced Breakdown Spectroscopy (LIBS) technique. It has been used to perform onstream analysis (OSA) of the chemical composition of slurries in both gold-ore and iron-ore processing plants. Industrial tests have been carried out respectively at La Mine Doyon (Cambior), a gold-ore processing plant near Rouyn-Noranda, Quebec, and at QCM's iron-ore pelletizing plant in Port-Cartier, Quebec. The aim was to demonstrate that the LIBS technique is capable of providing information that meets the needs for process control. C, Si, Ca, Mg, Mn and Al were the elements targeted on iron ore while Cu, Fe, Ag and Au were targeted for gold ore. The results obtained meet or exceed the requirements for process control and consequently clearly show that the LIBS technique is suitable for industrial applications.The feasibility of OSA, through in-plant validations using COREM’s LIBS mobile laboratory, has been demonstrated in four essential aspects: slurry sampling, LIBS chemical measurement, robustness for continuous operation, and functionality for industrial operators.INTRODUCTIONThere is a general need for optimization in the mineral industry. Process control is a favoured means to achieve this goal (McKee 1991). Real-time knowledge of process status is the key to effective control (Da Silva 1994). Only a few techniques, such as XRF, NMR and digital imaging, are currently amenable to chemically monitor industrial processes (Braden 2002). LIBS is an emerging technique with appealing characteristics for on-line and real-time measurement of bulk material (Lorenzen 1992, Palanco 2000). While our ultimate goal is to provide our industrial partners with performing monitoring tools, a shorter-viewed objective is to demonstrate the feasibility of developing a LIBS system for OSA. The LIBS technique has shown interesting capabilities for measuring solids, liquids, dusts and gases. Our work has focused on mineral slurries (Barrette 1999 and 2001, Turmel 1999). Special equipment is needed to perform in-plant validations. A mobile laboratory based on the LIBS technology has been assembled for this task."

Jan 1, 2004

By C. Schuffeneger

"The design of SAG milling circuits for mining projects requires the incorporation of the energy consumption considerations and the evaluation between different flexibility-adding options to absorb the time-dependent variation in the ore lithology. In order to expand the focus of the engineering design, a higher level of deepness and quality in the baseline information must be achieved to elucidate all of the constraints on throughput, energy consumption and product quality generating a design optimization consistent with an integrated vision of the process. This paper presents a review of a collection of typical examples of the copper and gold mining project in the Chilean Andes, in which both process and energy efficiency criteria are considered when the focus is to deliver an integral solution that incorporate those areas in the design. The intensive use of energy in the SAG milling, the process continuity and the quality of the product are a function of the proper design and selection of grinding equipment and plant layout, aligned with the mining plan and associated with projected future expansions and production increases.INTRODUCTION Autogenous and Semiautogenous grinding technology, large diameter and short length mills, begins with the Handsel design. During the decade of 1930’s, Handsel-Hardinge studies led to cascade mill development. Nowadays, 80 years later, continuous improvements in design and technology have been conducted to a completely new generation of gearless SAG mills that have led to an increasing capacity at the concentrator plants. Considering the existing alternatives, SAG mills are the most implemented option for the grinding circuit today. This work presents a review of the SAG mill implementation parameters and circuit considerations and its correlations in the most recent projects in Chile with an ore treatment capacity above 50 ktpd since the decade of the 90’s up to now. From this period, the tendencies will be analyzed using project design data. Based on process design information, the recent SAG mill history in relevant projects related to the new generation of commercial SAG mills, technical associated considerations and performance will be discussed. Circuit selection based on energy utilization will be revised to bring up a more holistic perspective on the SAG mill circuit design concepts. As is now well known, the heart of every concentrator plant are the grinding mills. Higher demands on throughput, availability and power consumption optimizations require not only high performance electrical equipment but also a well selected grinding circuit. The energy efficiency issues associated to the circuits design will be reviewed."

Jan 1, 2012

By Christopher F. Gleeson, Roger D. Thomas

"Abstract - Wawa has long been a center of mineral exploration activity and diamonds have been reported in the area since the 1930s. However, diamond exploration did not begin in the area in earnest until 1991. In 1993, Sandor Surmacz and Marcelle Hauseux of Saminex began a prospecting program in the area which culminated in their discovery of the "Sandor" diamond occurrence in an outcrop on the east side of the Trans-Canada Highway. They subsequently optioned the property to Spider Resources Inc. who obtained the necessary exploration permits from Algoma Central Corporation and undertook an exploration program. The diamonds at the "Sandor" diamond occurrence are hosted in the matrix of a spessartite dike composed of actinolite, biotite, and albite. Of the 64 similar dikes that have been sampled and analyzed to date, eight have been found to contain a total of 231 diamonds. Most of the diamonds are of high quality, although they are small.The dikes are non-magnetic and do not have any other geophysical characteristic that can be used to differentiate them from the adjacent country rock. All of the dikes discovered to date have been found by prospecting or by geological mapping by the Ontario Geological Survey. The dikes do not contain pyrope garnet or chrome diopside, two of the commonly used kimberlite indicator minerals. Instead, low Mg, high Cr, Zn-rich chromite, and ilmenites of variable composition, some of which lie within the field of kimberlitic Mg-ilmenite compositions, characterize the diamondiferous dikes. A regional-scale till sampling program for heavy minerals, and geochemical analysis of the <0.177 mm fraction, was used to further define the areas of occurrence of the spessartite dikes and to indicate additional areas for diamond prospecting. Heavy minerals in till that were most useful include: actinolite, chromite, and ilmenite. Geochemical analyses of the dikes show them to contain elevated concentrations of Ni and Cr and to be enriched in Ba, Co, V, Ca, Fe, and Mg relative to the surrounding rocks. Elevated concentrations of Ni and Cr in till occur overlying and down-ice of known lamprophyre dikes."

Jan 1, 2000

By R. W. Baker

"The development of uppers drilling at Brunswick Mining is reviewed. This paper describes design criteria for drilling patterns and the research required for selection of a suitable drill jumbo. The success of the uppers drilling program based on operating procedures is highlighted. IntroductionBrunswick Mining and Smelting Corporation Ltd., operates a 10 500 tonnes per day lead /zinc/copper I silver underground mine some seventeen miles southwest of Bathurst, New Brunswick .The No. 12 orebody, first discovered in 1952 by a group headed by M.J. Boylen, had extensive development, including two shallow shafts (500 ft), and test work carried out on it by St. Joe Lead between 1953-1957. However due to complex metallurgy and depressed metal prices, the operation was suspended.In 1961, a group comprised of M.J . Boylen, K.C . Irving and Patino acquired the rights of St. Joe Lead to the No. 12 property. A concerted development plan was initiated along with construction of the necessary sur face facilities and by July 1964, the property was in production at 4500 tons per day.In 1967 Noranda Mines Ltd. acquired operating control of Brunswick Mining and Smelting Corporation Ltd."

Jan 1, 1988

By V. K. Alves, P. Lacoste-Bouchet

"In order to improve ball milling efficiency in pellet plants, Companhia Vale de Rio Doce (CVRD), experiments new technologies in Santa Luzia (M.G. – Brazil) research center facility. Pilot grinding tests have been conducted with small grinding media, size distributed from 5 to 12 mm (millpebs). Tests have been conducted on an ore from CVRD’s Usina 5 Nibrasco, in Vitória, Brazil. A sample of the regrind circuit feed was obtained and used in comparative grinding tests with two types of grinding charges: 100% balls and a blend of 70% balls and 30% millpebs by weight. According to the balls charge, the grinding media mixture has showed the following benefits: reduction of the power draw, increase of the mill capacity, reduction of the circulating load and a slight increase of the ore blaine. Following the results obtained, CVRD is going to further explore the regrinding potential of millpebs.INTRODUCTIONCompanhnia Vale de Rio Doce (CVRD) is the largest mining company in Brazil. CVRD is involved in iron, base metals, gold and bauxite industries. Moreover, CVRD operates several pelletizing plants in Brazil and in other countries.CVRD’s Center for Mineral Development (CDM) is equipped with a comminution laboratory where studies are carried out that are aimed at the optimization of existing plants at several mining sites as well as the technical and economical feasibility of new projects. The laboratory is equipped with a complete pilot plant with several mills and classifiers, enabling continuous grinding tests in grinding circuits of almost any capacity and characteristics.In January 2004, CVRD undertook to conduct pilot tests at CDM for evaluating the effect of small grinding media on ball milling efficiency. Generally speaking, it is not unusual for operators to add oversize grinding media in a conventional regrind mill. This fact originates mainly from prohibitive prices of grinding media below 25 mm due to a production capacity decrease of grinding media producers. The size of the grinding media is an important variable affecting ball milling efficiency. Use of oversize balls decreases the number of contact surface between which particles can be caught and broken."

Jan 1, 2005

"The Ernest Henry Mining (EHM) ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite. At the end of 2009, EHM converted the ball mill media charge from forged steel to high chrome media. At high pH values (above 10.5), forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response. Given this, the pH in the roughers was dropped from 10.6 to 9.6 and it was found that there was a slight increase in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold. With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.INTRODUCTION The Xstrata Copper Ernest Henry Mine (EHM) is situated 38 km north east of Cloncurry, Australia. The mine began as an open-cut operation in 1998 and transitioned to a multi-sourced operation in December of 2011, utilising ore from the newly completed underground mine in addition to ore mined from the Mount Margaret Mining operations. EHM produces a combined copper gold concentrate containing 25 000 t of copper and 35 000 oz of gold annually, utilising a three stage grinding circuit along with a four stage flotation circuit. In addition to this EHM also produces 1 000 000 t of magnetite concentrate annually via a further grinding and three stage magnetic separation circuit. Based on metallurgical test work performed by Magotteaux between 2002 and 2008, the step to change from forged steel media to 18 percent chrome media was taken in 2009 in a bid to alter the pulp chemistry to improve the flotation performance in the plant (Greet, Kinal, Twomey, & Peatey, 2010). This plant trial resulted in: • Increased dissolved oxygen levels within the pulp, • A ball mill discharge Eh shift of 25 mV to more oxidising pulp potentials, and • An EDTA extractable iron percentage reduction. These improvements in the pulp chemistry resulted in an increase of 1.7 ± 0.6 percent in copper recovery and an increase of 2.9 ± 1.7 percent in gold recovery. As the plant trial using high chrome media was successful, the use of the media was adopted as the standard for the ball mill. This implementation opened the door for further process improvements around the flotation circuit."

Jan 1, 2014

By G. S. Hill, B. J. Huls

This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed the authors to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flowsheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit.

Jan 1, 2006