Search Documents

By D. Cruden

DISCODAT is a system of computer programs written for CANMET, Canadian Department of Energy, Mines and resources, to be used in analyzing geological data for rock slope design. The programs were written in Fortran IV for an IBM 360/67 computer. A program conditions field data from field forms for storage in a line file. Data may be selectively retrieved from the line file by a general retrieval program which uses a variety of relational operators. The retrieved data may be displayed as structural diagrams or histograms produced on a line printer or in a number of maps produced on a drum plotter. There is a logical sequence which leads to the characterization of those elements of the subfabrics of a rock mass which may be kinematically active. Structural domains within the rock mass can also be outlined by a procedure described as areal analysis. Costs for a complete analysis are usually substantially less than $l/discontinuity.

Jan 1, 1978

By X. -P. Zhang, L. N. Y. Wong

Shale gas exploitation initiated in North America has rapidly extended worldwide. Hydraulic fracturing is an emerging field technique for stimulating the gas reservoir. The study of cracking processes, particularly crack coalescence, is vital for a successful hydraulic fracturing to enhance the gas exploitation. Experimental studies have observed that the size effects of the constituent particles are significant on the cracking behavior of the rock specimens. To further investigate the size effects, the bonded-particle model (BPM), which is based on the discrete element method (DEM), is adopted in the present research. In flaw-containing specimens, by varying the crack resolution (?= a/2R), which is the ratio of half flaw length (a) to particle size (2R), the size effects on cracking behavior under compressive loading are studied. By keeping the flaw length constant, the particle size is varied independently in the BPM analysis. Decreasing the crack resolution increases the first crack initiation stress, but it has no obvious effects on the uniaxial compressive strength. The trajectories of the first cracks and secondary cracks hence generated have a higher resolution and are well-defined in those specimens possessing a higher crack resolution. On the contrary, in lower crack resolution specimens, the macroscopic first cracks appear to be wider and less continuous. These findings from numerical simulation clearly demonstrate particle size effects on cracking behavior. Special attention should be paid to these effects in future numerical study using the bonded particle model.

Jan 1, 2015

By P. Chryssanthakis

"The aim of this study is to give a better understanding for the behaviour of the composite material RRS and the synergy effect of its components while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10 m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. The newest part of the lower part of the Q-chart gives more information on required support compared to older Q-system versions. The RRS can be described as a three part composite material with the 3rd component being the reinforced concrete beam (with no fibers) and with steel rebars that are placed in groups and sprayed with pneumatically applied shotcrete in layers. The RRS usually have a total thickness varying between 0.20 and 0.50 m and a width between 0.25 and 0.60 m respectively. They are placed at different distances along the tunnel axis depending on the rock mass quality.In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. This was done by writing a FISH subroutine which is implemented in the discontinuous numerical code Universal Distinct Element Code (UDEC) that takes into account the characteristics of the reinforced beam (height, width, number of steel rebars, and spacing) in the calculation process. A rather extensive parametric study has been run by using the same key input rock mass parameters and in situ stresses (?H/?v = 0.5), and changing only the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam.The results show that: a) the S(fr) is almost overloaded in the first 4 hours after application in both tunnels; b) on the S(fr) and steel rebars, the stresses, axial and shear loads, as well as moments are decreasing after 16 hours and 28 days; and c) the bolts loads are increasing with time. The observed reduction in stresses and loads in both the S(fr) and reinforced beam is surprising. A possible explanation is that tunnel arches are self-supported to a lesser extent as time progresses due to redistribution of stresses in the nearby rock mass through the radial bolts. The loads in radial bolts are increasing by almost 25%. This can be seen from the overall results as we observe an increase in maximum principal stresses, displacements, shear displacements along joints and hydraulic apertures compared to tunnel baseline that has no support of any kind."

Jan 1, 2015

By K. Szczesny

This paper considers the integration of uncertain real-time logistics data for reactive construction scheduling. In order to manage a construction project efficiently, an accurate schedule representing the current project progress is inevitable. The quality and up-to-dateness of such a schedule depends on the availability of real-time data. Typically, real-time logistics data contain information about the availability of material, equipment and personnel as well as delivery dates and site conditions. The accuracy and inherent uncertainty depends on the location where the real-time data was acquired. Currently, the integration of such data into a construction schedule is a very time-consuming, manual and, thus, errorprone process. Therefore, this paper proposes a methodology that enables an automatic integration of such uncertain data into construction schedules. By integrating uncertainties into the existing schedule their impacts on the construction work can be evaluated. For this, discrete event simulation is applied. In order to model uncertain input parameters for simulation models this methodology applies the fuzzy sets theory. In combination with alpha-cut sampling technique, discrete model input parameters are obtained. By applying reactive scheduling with several discrete event simulation experiments, the results can be used to modify construction schedules according to agreed timeframes and costs. In order to demonstrate and validate the presented approach an example is conducted.

Aug 1, 2013

By A. Gakwaya, K. Ba, M. Guillot, J. Levesque

"In the aerospace industry, parts requiring tight dimensional tolerances and high mechanical properties are often produced by forging. This forming process allows for an optimal use of the material and can produce high quality parts at a reasonable cost. Thanks to CAD techniques, it is now easier to predict flow profiles and in-process defects occurrence as well as wear of the forging dies. However, in order to determine the properties of the forged part with computer simulation methods, a good material constitutive law is a prerequisite. This paper presents a virtual manufacturing process modeling for the closed die forging of a workpiece performed with Abaqus. The hot closed die forging is a regular process applied to manufacture metallic components used in aerospace industry. In this forming process, the material flow and final properties depend on the microstructure evolution during the process that is why it is important to include the microstructure effects in the material model. Based on the stress-strain data measured experimentally, the material parameters of the standard (classical) Johnson-Cook constitutive model and of a modified Johnson-Cook constitutive law including the microstructure effects have been determined. The obtained simulation results are compared with the experimental results for validation.INTRODUCTIONDue to their good physical and mechanical properties such as ductility, fatigue strength, corrosion resistance and rupture, aluminium alloys are often used in the aeronautic and the automobile industries. In this work, we present the forging of an Al-Zn-Mg-Cu alloy, a high strength aerospace alloy recognized for his good combination of physical and mechanical properties. The forging process is simulated in Abaqus Explicit using both the standard Johnson-Cook law (Johnson & Cook, 1983; Hor, 2011; Lin et al., 2012), and its modified version as proposed by Andrade et al., (1994). The Johnson-Cook law offers the advantage of considering the coupled effect of the plastic strain, the plastic strain rate, the temperature of forging and the hardening effect. However, it is a phenomenological model which does not account for the effect of the microstructure evolution. In this work, a modified Johnson-Cook model implemented in a user subroutine is used. It includes the effect of the dynamic recrystallization phenomenon during the hot deformation. The dynamic recrystallization has a noticeable influence on the microstructure and on the properties of the material. The term dynamic means that the process starts and acts during the deformation and this is different from the static mechanism of recrystallization which occurs during an annealing and after cold or hot deformation. Since properties of the alloy used in this work are not readily available in the literature then characterization tests have been done at various temperatures and strain rates, in order to determine the thermomechanical properties and the material behavior during the process of hot forming, more precisely during the hot forging process."

Jan 1, 2016

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008

By S. M. Bradshaw, E. Charikinya

"Microwave induced cracks have the potential to enhance metal recovery from coarse sphalerite particles in heap leaching operations by creating new crack surface areas for lixiviant and enhancing value mineral exposure. The mode of fracture and the extent of mineral exposure due to microwave induced cracks have not yet been investigated. The objective of this study was to determine the extent of particle damage and mineral exposure in microwave treated particles. This was done using X-ray computed tomography (XCT) and image analysis techniques. XCT analysis was conducted on small (–5+4.75 mm), medium (–16+9.5 mm), and large (–25+19 mm) sphalerite ore particles before and after microwave treatment (MT). Geometrical properties, such as volume and surface area of each mineral phase in each particle was determined from the XCT reconstructed images using VGStudioMax image analysis software. These geometrical properties were used to calculate the interfacial areas of sulphide mineral grains in microwave treated particles before and after MT. The ratio of specific interfacial area after MT to specific interfacial area before treatment was used as an indicator of the degree of preferential grain boundary fracture. The results showed significant grain boundary fracture after MT at all sizes. For small sized particles, about 31% of the interfacial area was lost compared to 23 and 16% for medium and large particles, respectively. The results also showed an increase in the degree of mineral grain exposure of 28, 26, and 15% for small, medium, and large particles, respectively, after MT. These results provide experimental evidence supporting improved mineral exposure due to MT. INTRODUCTIONFor some years it has been suggested that microwave treatment (MT) of ores might result in preferential grain boundary fracture that would have benefits such as improved grain exposure and particle weakening. (Kingman, 2006). Most of the experimental work investigating the application of microwaves to mineral processing flow sheets has focused on assessing the benefits of applying microwave technology to flow sheets consisting of size reduction and mechanical flotation cells (Kingman et al., 2004). Experimental studies have shown that coarse crushing during tertiary grinding of microwave treated ore resulted in a better liberated coarser flotation feed (Scott, Bradshaw, & Eksteen, 2008). It has been suggested that improved liberation in milled flotation feed, was due to the presence of grain boundary fracture in microwave treated particles. However, this improvement in coarse particle liberation does not necessarily translate to a significant improvement in downstream flotation recovery (Kobusheshe, 2010). This is as a result of the size limit to the flotation of coarse material, due to detachment forces acting on particle-bubble aggregates, which increase as the particle size increases (Jameson, 2012). Current conventional, mechanically agitated flotation cells are not designed to float coarse material (Jameson, 2012). Hence it has been difficult to show the downstream processing benefits of applying microwaves to ores processed by comminution followed by flotation (Kobusheshe, 2010). It is clear from investigations carried out so far that inappropriate downstream exploitation of microwave treated ore would fail to realise a meaningful process benefit (Kobusheshe, 2010; Ali & Bradshaw, 2011)."

Jan 1, 2016

By E. Rezazadeh Azar

Dump trucks are the main mean for hauling earth material within and outside of the construction and open-pit mining jobsites. The real-time monitoring of the material transportation trips is beneficial for proactive equipment management, volume estimation, and productivity measurement. The traditional manual observation is tedious, non-real-time, and expensive; therefore remote sensing technologies, namely GPS and RFID, have been employed for this reason. Ordinary construction videos are another costeffective alternative to monitor dirt loading and hauling operations in real-time. A vision-based system has been developed to recognize and count hauling trips. This system has three modules including object detection, tracking, and action recognition. This system processes videos taken from access roads in which it recognizes dump trucks and then tracks them throughout the viewfinder. The action recognition module is designed to reject false alarms and also terminate tracking. This way, the system is able to count the number of hauling trips and also record the time between each trip. Several state of the art computer vision algorithms were employed to develop this system. Some of these algorithms were modified using spatiotemporal information to minimize the inherent errors of the vision-based methods. The experimental results showed considerable performance of the system for practical application in the construction and mining sectors.

Aug 1, 2013

By C. T. Morley

The steadily increasing interest in high pressure grinding rolls (HPGR) as a legitimate alternative comminution technology for hard rock applications has led to a proportional increase in the demand for trade-off studies comparing HPGR with more established approaches, typically SAG-based but including AG and stage-crushing designs. The primary trade-off is between a) the higher capital cost typically incurred with HPGR-based designs and b) the higher operating costs of the more traditional technologies. However, if, through circuit design innovation, the capital cost penalty of HPGR circuits could be eliminated or reversed, then the need for trade-off studies would diminish.

Jan 1, 2012

"An atmospheric process for the synthesis of scorodite(DMSP®)has beendeveloped,in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. Under optimum conditions, the synthesized scorodite (FeAsO4?2H2O) was well crystallizedand the crystals were faceted; the particle sizes were as large as 15 to 20 µm. In thisstudy, iron (II) sulfate heptahydrate (FeSO4·7H2O), arsenic (V) acid (60mass%H3AsO4) solution, and distilled water were used to prepare the original experimental solution (700 ml), in which the contents of Fe(II) and As(V) were 55.9 g/L and 50.0 g/L, respectively. The effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas injectionrate, temperature, and the initial pH of the solution, on the size and shape of the scorodite particles wereinvestigated. From the experimental results, the changes in the shape of the scorodite particles wereclarified for each synthesis condition.INTRODUCTIONDOWA has developed a processfor synthesizing well-crystallized scorodite (FeAsO4•2H2O). Theprocess is named andtrademarked as DMSP® (Fujita et al., 2008; Fujita et al., 2008; Fujita et al., 2009; Fujita et al., 2009; Fujita et al., 2009, Kubo et al., 2010). In this process, oxygen gas is injectedinto a sulfuric acid solution containing large amountsof As(V) and Fe(II). Facetedscorodite crystals as large as 15–20 µm weregeneratedthrough the pre-formation of a gel-like precursor. However, it is known that the synthesized scorodite particles become smaller and more aggregatedwhen the synthesis conditionsdeviate from the optimumconditions.In this study, the effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas flowrate, temperature, and initial pH of the solution, on the size and shape of the scorodite particles were investigated. The experimental resultsclarified the changes in the shape of the scorodite particles for each synthesis condition."

Jan 1, 2016

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By Z. Z. Öztürk, N. Sarica, A. H. Üçisik, C. Bindal

"Titanium oxide films were fabricated on commercially pure titanium surfaces via anodization procedure. Anodization parameters, anodization time and voltage were altered, whereas temperature and chemical composition of anodization bath were kept constant. The main idea in this study is to obtain rough titanium-oxide surfaces. The type and feature of titanium oxide formed were observed via SEM and EDX analyses. What was revealed from SEM and EDX analyses were combined with Ti-O phase diagram in order to make judgment on the type of phases obtained, e.g. solid solution and/or compounds. Studies on the different regions of each sample showed that surfaces consist of different titanium oxide compounds with various O/Ti ratios in nano level and solid solutions varying in terms of chemistry on the same sample. Thus together rough surfaces and inhomogeneous distribution of "titanium oxides" were obtained. It was also found that when anodization time and voltage were increased, more granular surface with higher O/Ti atomic ratio was obtained."

Jan 1, 2015

By J. E. Udd, S. Bharti

"ABSTRACTMonitoring of stability conditions in underground mines permits management to assess the response of the rock mass to mining strategies. Monitoring of movements, if sufficiently early, may also permit operators either to avert potential failures or to develop alternative approaches to extraction.The Falconbridge organization has been a leader both in the uses of rock mass stability monitoring techniques and in the development of instrumentation.In this paper, the authors review the Falconbridge approaches to monitoring, and present case history examples to illustrate the application of the various instruments used.RESUMELa surveillance des conditions de stabilité dans les mines souter-raines permet aux chefs d'enterprises d'évaluer les réactions de la masse rocheuse aux méthodes d'extraction minière. Si le contrôle des mouvements du terrain est effectué assez tot, l'exploitant pourra prendre les mesures qui s'imposent, soit pour éviter les détériorations possibles ou pour mettre au point de nouvelles méthodes d'extraction.Le groupe de la Falconbridge a ére le premier a utiliser des techniques de vérification des conditions de stabilité de la masse rocheuse et a mettre au point l'appareillage requis.Ce document présente une revue des méthodes employées par la Falconbridge pour assurer la surveillance active de la stabilité de la masse rocheuse et illustre au moyen de cas concrets la manière d'utiliser les divers appareils."

Jan 1, 1987

By C. J. Sullivan

Many metalliferous ?provinces are co-extensive with particular groups of sedimentary, volcanic, or :basic plutonic rocks. Deposits may be truly syngenetic (Rand, Rhodesia-Katanga, Mans-field, Blind River, White Pine); re-. concentrated by circulating waters (Colorado Plateau, Red Bed Coppers) ; or re-concentrated thermally during metamorphism and granitization (most uranium and lead-zinc provinces ?and some copper and gold provinces). Basalts may yield important cop-per provinces when folded and re-heated. Granitization of basalts which have not reached the chlorite-carbon-ate phase of metamorphism may produce copper provinces. If they reach ?the chlorite-carbonate stage, granitization may result in a gold province. Copper and copper-nickel provinces may result if gabbros are granitized, and a ?similar alteration of per-idotite may result in asbestos or nickel ores. Many similar associations are known. Granite is not a source of ore, but a result of heat. A classification of ?ore with respect to source rocks is of greater prospecting value than are classifications based on magmatic differentiation and hydrother-mal solution theories. Volcanic centres are important ore foci because the thermally unstable metallic sulphides may be concentrated here by a distillation process. The ores found in the hot spring deposits, viz., mercury, mercury sulphide, sulphur, and the compounds of ?antimony and arsenic, are not those which are soluble in water at low temperature (epithermal sub-division of hydrothermal class), abrut those which are unstable thermally at comparatively low temperatures . Water is one of the most common thermally unstable minerals, and generally accompanies the thermally activated ore-forming sulphides.

Jan 1, 1957

By J-g. Cui, X-b. Guo, J-j. Wang, J. Qiao, H. Tian

"Rare earth elements have unique properties because of the special electronic structure. In this paper the improvement of refractory material performance by the light rare earth oxides was introduced. The experiments showed that adding a bit of rare earth oxide could obviously improve the performance of the refractory material. INTRODUCTIONIn recent years, refractory materials are widely applied in the steel smelting process as a ladle lining material. In China, although the total production of fire-proof material exceeds normal demand, but the quality and variety of fire-proof material still have a big gap with world advanced level. A number of refractory products need to be imported from abroad. With the rapid development of domestic steel production, the ladle lining with refractory is gradually running after the world advanced level on production technology, production variety, and quality level. It replaces some imported products meeting the needs of the development of the iron making production. Therefore, there is an important significance to research on solving the problems of the ladle refractory reasonably and avoiding or reducing blind and not proper use of the imported refractory ( Jing, 2007).On the other hand, rare earth oxide has some special excellent properties. Firstly, they are very good refractory materials with their high melting point;Next, they have good resistance to water and alkali resistance function;Thirdly, it is easy for rare earth oxide to generated composite oxide reacting with other metal oxide,achieving the purpose to improving the material properties (Xu, 1978; Diao, 1979). China has a variety of rare earth resources,and rare earth resources is more advantageous in Baotou,taking up about 36 percent of world reserves,which is the world's top of rare earth mineral. In recent years the rare earth products output has risen sharply and many varieties and specifications have appeared. So it is necessary to study the new field of rare earth compound to open up new markets. Thus, it has a very vital significance to promote the further development of rare earth industry, adjust the rare earth products structure, ease the contradiction between supply and demand, and improve refractory products quality and grade in order to better serve the main body production.I In this paper, the experiments are mainly for 210 tons of Al2O3-MgO style series refractory materials belong to ladle lining bag from Baotou Iron & Steel Group Corporation Sheet Factory. The improvement to the effect of refractory material performance is explored by using light rare earth oxides as additives."

Jan 1, 2012

"This paper deals with the reconciliation of open stope performance at Olympic Dam, South Australia, with a focus on stope stability, recovery, and operational aspects of stope reconciliation in relation to the expected or planned stope design. The observed stope performance is inconsistent with the equivalent linear overbreak sloughing criteria for assessing the performance of large open stopes. The aim is to investigate new stope performance criteria using quantitative (overbreak, underbreak, maximum depth of wall failure) and qualitative (stope productivity, observed fragmentation) information that correlates with the observed stope behaviour, providing a process for improving future stope designs.RÉSUMÉ Le présent article traite de la réconciliation de la performance des chambres ouvertes à Olympic Dam, Australie du Sud, en ciblant la stabilité des chambres, la récupération et les aspects opérationnels de la réconciliation des chambres par rapport à la conception attendue ou planifiée des chambres. La performance observée des chambres ne concorde pas avec les critères d’épaisseur équivalente du bris hors profil pour évaluer la performance de grandes chambres ouvertes. L’objectif est d’étudier de nouveaux critères de performance des chambres au moyen de données quantitatives (rupture hors profil, rupture à l’intérieur du profil planifié, profondeur maximale d’effondrement du mur) et qualitatives (productivité de la chambre, fragmentation observée) qui concordent avec le comportement observé des chambres, fournissant ainsi un processus pour améliorer les futures conceptions des chambres."

Jan 1, 2015

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

By B. Stettner, J. Asante, S. Abraham

The levels of nitrogen in steel produced in various metallurgical vessels vary significantly. For example, the tap nitrogen levels in steel produced in the BOF are around 4Oppm, as compared to 70-100ppm in both DC and AC electric arc furnaces. Given the pressing need to reduce nitrogen levels in steel to satisfy customer demand, IPSCO Inc. has gained considerable experience in controlling nitrogen levels in steel over the course of the last three years. Hence, a cost effective process has been developed through an intensive nitrogen control program from steel melting in the EAF through to the continuous slab casting stage. This paper describes the practices employed at each stage of the steelmaking process that have enabled IPSCO Inc. to reduce and control nitrogen levels in steel.

Jan 1, 2004

By D. J. King

The development in recent years of a fluidized bed system for use as a counter-current solid ion exchange loading contactor for the purification and concentration of uranium from leach liquors has had a major impact on the design of uranium extraction plants. The main object of this paper is to describe many of the variations that can be applied to the design of uranium extraction plants arising from the use of a fluidized bed loading contactor with a view to providing a guide for the development of a flowsheet for a new uranium extraction plant. The paper has been devoted primarily to the consideration of conventional uranium extraction plants in which a ground ore is leached in mechanically or air agitated tanks. The effect of the use of a fluidized bed loading contactor on each of the plant sections from leach to uranium purification and concentration has been considered. In order to describe most effectively the impact of using a fluidized bed solid ion exchange loading contactor, its use has been compared with the performance that can be achieved with the most common alternative purification processes. The comparisons are made largely on a technical basis, but the effect on the capital and operating costs of the different uranium extraction flowsheets are described qualitatively. In making these comparisons, consideration is given to the effect on the size, number and materials of construction of equipment items and how the quantity and composition of the liquid effluents can be controlled to reduce the environmental problems arising from the disposal of these effluents. The paper also discusses some of the factors that should be taken into consideration in the design of a fluidized bed loading contactor and describes various designs of the elution section that can be used in conjunction with the loading contactor.

Jan 1, 1979