Search Documents

By G. J. Hamilton

"THE Royalite-Canada Southern Coleville No. 1 gas strike of August 15th, 1951, and the closely following low gravity black-oil strike of August 23rd, were the first of a series of recent oil and gas discoveries in western Saskatchewan. They are in what is now known as the Coleville field, 25 miles north and west of Kindersley and 30 miles east of the Alberta-Saskatchewan border (Figure 1).Gas flows have been recorded in the Viking sand at daily rates of between 5 and 10 million cubic feet, and black oil of 15° A.P.I. gravity is produced from Mississippian sediments of Banff age at a daily rate .of 50 to 100 barrels on pump.Development drilling was carried on during the winter months, with very little attempt at step-out exploratory ventures. This year, however, a step-out programme to the northeast (Figure 2) is •being carried on in order to determine the position of a possible truncation of Mississippian sediments in that direction. Section 30 of the Coleville area has been fully developed on a 20-acre wellsite basis, and structural information is restricted to local rather than regional interpretation. No attempt will be made in this paper to interpret the Coleville area with respect to the regional geology in any but a general manner."

Jan 1, 1952

By A. A. Tytko, T. S. Golosinski

"The paper discusses the accuracy of magnetic inspections of corroded hoist ropes. It quantifies the error of measured LMA (loss of metallic area) caused by presence in the rope of ferromagnetic products of corrosion. The paper concludes that in mining practice this error is not significant. Hoist Rope Corrosion and its AssessmentCorrosion is one of the most common forms of wire rope wear. For ropes working in wet mine shafts, ropes used by the fishing industry and, in general, ropes working in humid and chemically active environments, corrosion wear is usually the prime reason for rope discard. In most mining applications, rope corrosion is accompanied by fatigue cracking of wires, abrasion of external wires, internal nicking and other forms of wear.Quantification of corrosion damage in ropes using standard inspection procedures and examination methods is very difficult. Qualitative comparisons are sometimes used to describe the degree of rope corrosion to compensate for the lack of quantitative measures (SABS 0293, 1996). If available, the results of magnetic examinations of ropes may be of help in assessing their corrosion weakening.Magnetic rope examination requires that the rope first be magnetized. After that, the rope magnetic flux and the leakage flux along the rope are measured. The first is assumed to be directly proportional to rope metallic area (LMA) and its changes are indicative of the rope’s loss of breaking strength (LBS). Existence of the second indicates existence of local faults (LF) in the inspected rope. As the corrosion of rope results in development of corrosion cracks and in loss of rope metallic area, both the LF and the LMA should be used to quantify the level of rope corrosion. More specifically, the changes to the amplitude of the LF signal are considered to provide qualitative information on rope corrosion (Hansel et al., 1990), while those of the LMA signal are believed to provide quantitative information (Geller and Rousseau, 1990; Golosinski, 1996)."

Jan 1, 1999

By H. Aaltonen, T. G. Robinson, M. Morimitsu

"The energy required to plate pure zinc can be the most significant operating cost for an operator in the production of electrolytic zinc. This paper reports on developments on low energy Outotec coated titanium anode process technology with fully amorphous coatings, MSA®, and its application to brownfield zinc electrowinning operations around the world. This technology aims to reduce the operating cost and increase productivity for zinc producers.INTRODUCTIONZinc electrowinning is an energy-intensive process using more than 3,000 kWh/t of electric energy [1-4], and the reduction of the energy consumption is one of the key issues. The high energy consumption is due to a high cell voltage during electrolysis, which is mainly caused by a high overpotential of oxygen evolution reaction on lead alloy anodes which have been widely used in commercial zinc electrowinning processes. The overpotential of oxygen evolution is 0.6 V or more and which is approximately 4 times higher on average than that of the cathodic reaction (zinc deposition) [3,4]. Therefore, the reduction of oxygen overpotential is significant to reduce the electric energy consumption, and this will become more significant with increasing demand in metal production and rising energy costs.Oxide coated titanium anodes have been widely investigated for the oxygen evolution anodes in order to replace the lead alloy anodes [5-9], because it is known that the oxygen overpotential strongly depends on the material and structure of the anode. The most typical example of such anodes is an IrO2-Ta2O5 coated titanium anode, which is usually prepared at thermal decomposition of a precursor solution containing metal salts at 450 oC or more and obtained mixed oxide coating consists of crystalline IrO2 and amorphous Ta2O5. On the other hand, one of the authors of this paper, Professor Morimitsu, Doshisha University in Japan, has developed a novel oxide coated titanium anode, MSA® [10-25]. The most specialized point of MSA® is that the catalytic coatings are prepared at low thermal decomposition temperature and amorphous IrO2 or RuO2 is contained as the components in the coatings. Such amorphous coatings have high catalytic activity for oxygen evolution compared to lead alloy or crystalline coatings. Outotec acquired the international specialized MSA® patent licensing rights from Doshisha University and has produced and commercialized the amorphous oxide coated titanium anodes. These anodes have already been utilized mainly in copper electrowinning plants worldwide and have demonstrated a significant voltage reduction, a cost-efficiency, and a long lifetime. This novel technology is also effective to zinc electrowinning process, thus this paper presents the characterization and performance of amorphous IrO2-Ta2O5 coated titanium anodes and amorphous RuO2-Ta2O5 coated titanium anodes for oxygen evolution in zinc electrowinning."

Jan 1, 2016

By A. A. Goss

We investigate the relationship between corporate financial performance (CFP) and environmental and social performance (CSP) in a sample (n=165) of large, publicly traded U.S. mining and oil and gas firms. Using optimally scaled principal components analysis to generate aggregate measures of CSP strengths and concerns, we find higher concerns are related to higher volatility of unexpected earnings and discount rates. Furthermore, these earnings shocks are more likely to be negative as concerns increase. Decomposing this relationship shows that negative environmental performance dominates proactive environmental management as a driver of unexpected earnings, but proactive community efforts increase the magnitude of earnings shocks. We document some evidence of the strategic use of CSR, with those firms that have greater risk investing more proactively in CSR.

Aug 1, 2013

By C. G. Williams

IN preparing this paper on Canadian mine taxation, there has been no attempt to detail the requirements of the various taxing bodies; but rather to consider the matter from the standpoint of its underlying principles and give a general idea of the methods adopted. I have added an Appendix setting forth the principal features of the various Acts, which should be used for general reference only, since new rulings alter minor details from time to time. In current legislation, many important points are left to the discretion of the Ministers and their deputies. We are, indeed, fortunate in having in Canada an able and conscientious body of permanent officials, who bring a sense of justice and courtesy to their work which is most commendable, and which has done much to simplify the working out of general problems. The production of metals may rightly be deemed a form of manufacture, but differs from the average manufacturing business in three important respects: (1) In its early stages, it is wholly speculative, since it is impossible to make any definite appraisal of value or possibilities. (2) The principal asset of any mine, i.e., the ore in the ground, is a wasting asset, and is irreplaceable. (3) Any additional burden by way of taxation cannot be passed on to the public but must be borne entirely by the producer. Having regard to the first of these differences, it is apparent that, since the risk of loss is great, the reward in case of success must be correspondingly great. This fact seems to be constantly overlooked by those who regard the all too few outstanding successes in Canadian mining history as fit prey for predatory legislation. As an illustration of the speculative nature of early mining development, let us consider the Province of Ontario-and I take this illustration simply because I am more familiar with conditions there, and not because I believe it differs greatly from any other province. From 1907 to 1933, 165,243 claims were staked and recorded, from which 43 mines were developed which paid one or more dividends. There was, of course, some duplication through re-staking; also, on some claims very little work was done, and most mines have more than one claim. But, since staking and recording cost real money and effort, each of these claims must have been considered to have had merit.

Jan 1, 1935

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

By R. Loney, M. Militzer

There is a significant demand for new high strength steels with fine grain sizes for structural applications. One approach in this regard is to develop hot-rolled HSLA steels where refining the microstructure leads to increased strength levels, e.g. 700 MPa yield strength, that can be attained by suitable modifications of chemistry and processing. Here, an HSLA steel is investigated that contains 0.05wt%C-1.65wt%Mn-0.20wt%Mo¬0.07wt%Nb-0.02wt%Ti and approaches the above strength class. The ability to control and predict the mechanical properties of hot rolled steel depends strongly on the thermomechanical processes, which the steel undergoes. The final microstructure and, thus, the properties of the hot-rolled steel are a function of the austenite decomposition obtained during accelerated cooling on the run-out table and precipitation during coiling. The austenite-to-ferrite phase transformation under run-out table conditions has been investigated using a Gleeble 3500 thermomechanical simulator equipped with a dilatometer. The effects of cooling rate and initial austenite microstructure including the degree of work hardening on austenite decomposition kinetics and ferrite grain refinement have been quantified. Results show that grain refinement can be optimized by the presence of work hardened austenite and accelerated cooling. Based on the experimental results, a model is proposed to predict the transformation start temperature and the resulting ferrite grain size for run-out table cooling conditions.

Jan 1, 2004

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By Z. I. Zaki

Synthesis of TiC /A1203 Composite from TiO2, Al and graphite using combustion technique has been investigated at different initial temperatures; room, 400 and 600 °C. The effect of initial temperature on the composition of the product, wave velocity and combustion temperature of the reaction was studied. The measured combustion temperature and wave velocity were increased with increasing the initial temperature of the combustion reaction. The maximum wave velocity obtained was 5.9mms-1 when conducting the combustion reaction at initial temperature of 600 °C. Oxidation resistance of the obtained composite was also studied at the temperature range 300-800 °C. No oxidation is detected before 400 °C while it takes place effectively at 700 °C forming different titanium oxides. Wave velocity measurements method was used to calculate the activation energy of the reaction between the starting materials. It was found to be 316.34 kJ mol 1 at the temperature range that was studied.

Jan 1, 2007

By Gordon A. Irons, H. Y. Hwang

An impinging gas jet on a water surface was studied to understand momentum transfer in oxygen steelmaking. Depth, width and oscillation frequency of the jet cavity were measured and the splashes interpreted with Kelvin-Helmholtz instability and combined Rayleigh-Taylor and Kelvin-Helmholtz instability theory. A model to calculate separate gas and liquid velocities, applying the exact momentum boundary condition, is proposed.

Jan 1, 2004

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By Minerals Refining Company, Gerald Luttrell, Biao Li, Robert Bratton, Roe-Hoan Yoon, Stan Suboleski, Nikhil Gupta

Flotation is regarded as the best available method of upgrading coal and mineral fines in the mining industry. However, its efficiency deteriorates rapidly with decreasing particle size. Furthermore, ultrafine concentrates are difficult to be dewatered economically. Due to these technological problems, some operators are forced to discard at least part of the ultrafine materials to tailings (or refuse) ponds, causing significant losses of valuable resources and creating environmental concerns. To address these technological issues, a new separation process named hydrophobic-hydrophilic separation has been developed on the basis of the recent advances in the science of hydrophobic interactions. The results obtained to date show that the process can recover and dewater ultrafine particles simultaneously with high separation efficiencies. Following a series of extensive laboratory tests, the process has been scaled up to proof-of-concept and pilot-scale continuous tests. The results obtained with desliming cyclone overflows, screenbowl effluents, and by-zero coal flotation feeds can be cleaned to less than 4% ash and moisture with over 97% organic matter (or coal) recoveries. The results obtained with mineral fines also showed encouraging results.

Jan 1, 2016

Adsorption of guar gum was investigated on model minerals typically found in water-insoluble slimes of potash ores. The ionic strength of the adsorption mixtures was varied from distilled water to saturated NaC1 and KC1. The tests were also performed using a saturated brine. The adsorption density of guar gum on illite, dolomite, and kaolinite was found to be not only a function of total ionic strength but also of the type of electrolyte present in solution. Generally, the adsorption of the polymer on the clay minerals was higher in KC1 solutions than in NaCI, but the differences gradually disappeared when the electrolyte concentration approached saturation. The results were analyzed in terms of chaotropic (K ) or kosmotropic (Na') properties of background counter-ions and their different behaviors at the hydrated mineral-water interface. Guar gum adsorption on dolomite was related to the presence of calcium and magnesium sites on the mineral surface, and to the cis-configuration of OH groups of mannose units. Based on viscosity measurements, it was suggested that guar gum macromolecules form entanglements in NaCI solutions (and distilled water), but individual molecules exist in KC1 solutions thus creating different modes of adsorption of guar gum from concentrated NaCl and KCl solutions.

Jan 1, 2006

By R. Q. Honaker

It has been shown that naturally hydrophobic carbonaceous materials such as coal and graphite can be selectively coagulated and separated from hydrophilic impurities without using oily agglomerants, flocculants or electrolytes. The coagulation occurs at C-potentials significantly higher than those predicted by the classical DLVO theory, suggesting that it is driven by the hydrophobic interaction. In the present work, the energy barriers for the coagulation of a hydrophobic coal sample have been calculated using the extended DLVO theory which incorporates the hydrophobic interaction energy in addition to the dispersion and the electrostatic energies. For the coagulation of minerals present in the coal, the classical DLVO theory has been used for the energy barrier calculation. The results of these calculations provide an excellent correlation with the results of a series of Selective Hydrophobic Coagulation (SHC) tests conducted with run-of-mine coal and graphite samples.

Jan 1, 2004

By F. E. Lathe

RECENT events have emphasized with renewed force the well known fact that war greatly intensifies the demand for certain metals, particularly for iron, copper, and zinc. Any increase in the use of iron and steel, whether in war or peace, is also accompanied by increased consumption of those metals which find their chief application as ferro-alloys, such as nickel, chromium, manganese, molybdenum, tungsten, and vanadium. Further, since high temperatures are essential for the production of all these metals, activity in the metal industry is inevitably accompanied by an insistent demand for refractories. For example, in North American practice the consumption of magnesitic hearth refractories is frequently expressed in pounds per ton of steel. This quantity (not including straight dolomite) ranges on individual plants from about 7 to 12 pounds. When the industry is operating at approximately full capacity, the ratio of refractory to steel tends to increase, since the tonnage of steel produced is recognized as of paramount importance, and this leads to the harder driving of furnaces and less regard for the effect on refractories. It should also be observed that the cost of refractories per ton of metal produced is always so low, in comparison with other items, that it may even increase while the cost of metal per ton is being reduced through more continuous operation and the use of higher temperatures. As one prominent Canadian copper metallurgist has tersely expressed it, he is "not in business to save refractories but to smelt ore". The effect of war demands and of general industrial activity upon the production of basic and neutral refractories is clearly shown in Figure 1, which gives the value of chrome ore and magnesitic-dolomite produced in Canada during the period 1907 to 1937. Tonnages have not been shown, as these are not available for the full period; such figures as have been published from time to time are not strictly comparable, since both raw rock and finished products have on occasion been included. The preliminary figures for 1938, which are now available, have been prepared by the Dominion Bureau of Statistics on a different basis from those immediately preceding, and have therefore not been shown.

Jan 1, 1940

By Janos de Warga

"After a short introduction to the history of the semi-conductor theory, the paper describes the principles of electron and hole flow in the semiconducting materials, the operation of the PN junction, and the rectification process in multi-layer devices (diodes and SCR's). The various methods of purification and zone-refining of the silicon are illustrated prior to the discussion on the most commonly used junction-forming processes (alloying, diffusing, etc.). Modern device fabrication and packaging operations are illustrated. Factory testing, evaluation, electrical parameters and guaranteed rating characteristics are listed. It is explained in this paper how the various device parameters affect the electrical performance of the finished unit and how the finished unit characteristics (turn-on, turn-off time, etc.) will influence the equipment rating. In concluding, some typical items of equipment are highlighted, and the applications of these semiconductor rectifiers in the chemical, mining, pulp and paper, and steel industries, etc., are dealt with."

Jan 1, 1967