Search Documents

By K. Honkivaara, S. Junnikkala, J. Aho, K. Föhr, P. Lampinen

"Bubble area flux has been claimed to be a major tool to dimension flotation equipment. The paper describes laboratory scale (batch and 301 continuous cell using plant feed) and small-scale (1 ,8m3) industrial experiments with coarse-grained massive sulphide ore.Samples were taken with different froth thickness and air addition rates while the bubble size was measured with an UTC capillary device. Problems of averaging the bubble size measurements and the bubble area flux measurements are also discussed.Material balances were calculated using the commercial program BILCO. The flotation rate constants were calculated for pulp and for froth assuming that we can extrapolate the flotation rate constant of the pulp phase from tests using very thin froth thicknesses.The results indicate that the bubble area flux is not alone an adequate dimensioning tool. With fine sizes there was a nearly linear relationship between the bubble area flux and rate constant for constant impeller revolutions. For coarse sizes the form of the relationship is non-linear and seems to go through a maximum value. Thus the final flotation outcome is not a simple function of bubble area flux but depends on the particle size distribution and other more traditional flotation cell dimensioning variables. The effect of the froth residence time in the total recovery of coarse particles is large, but will not be treated in this paper."

Jan 1, 2000

By Mani Manimaran, Inna Dymov, Mariam Melashvili, Chris Fleming, Joe O’Day

This paper presents experimental evidence that supports the use of bromine/bromide as a potential alternative to conventional cyanidation for gold leaching. The study evaluated a brominebased lixiviant, Stabilized Bromine, with considerably lower vapour pressure than liquid bromine. Using a rotating device, the rate of gold dissolution was determined at various concentrations of this reagent. The reactivity of pure pyrite, arsenopyrite and chalcopyrite minerals was also evaluated in stabilized bromine reagent. Furthermore, bromine leaching of gold in a number of gold bearing ores was undertaken. Results showed that significantly higher gold recovery can be achieved with bromine than with cyanide when leaching gold encapsulated in sulphides, but bromine consumption was high owing to simultaneous oxidation of the sulphides. The greatest promise for the bromine leach process was with oxidized gold ores. The recovery of gold from oxide ores with bromine was comparable to that achievable with cyanide and bromine consumption was reasonable when leaching was conducted at a near neutral pH of ~6. In the case of oxidized gold ores containing copper mineralization, it is possible that bromine consumption may be lower than cyanide consumption, since there is evidence to suggest that bromine is less reactive than cyanide with copper minerals.

Jan 1, 2014

By John G. Henning

The Hoyle Pond underground mine is located in the Porcupine Gold Camp, 18 km east of downtown Timmins. Since the initiation of production in 1985, the operation has produced in excess of 1.9 million ounces of gold at a grade of 15 grams per tonne. Currently, Hoyle Pond ranks 8th in total ounce production for all past and present producing mines in the camp, with the highest head grade of any of the significant past, or present producing mines in Timmins. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. Using illustrative examples, this paper provides an overview of factors, such as geologic setting, rock mechanics challenges and mine infrastructure, which influence mine design at Hoyle Pond.

Oct 1, 2004

By Doug Smith, Gary Taylor, Paul Ogryzlo

"Uranium mining and processing typically requires large quantities of high-grade reactive quicklime for the neutralization and clean-up of contaminated mine water and mill process waste streams. Currently the Saskatchewan uranium industry’s lime requirements are being supplied from deposits located in Manitoba and Alberta, resulting in transportation costs, which equal or exceed the market value of the product. During the summer of 2001, the northern village of Pinehouse located 220 kilometers south of the Key Lake uranium mill, staked two previously discovered limestone deposits. The relatively shallow deposits, known as Missi Island and Sleeping Giant are located in close proximity to one another, approximately 35 km south of Pinehouse adjacent to highway 914. This paper describes the results of a scoping study carried out by AMEC for the development of the two deposits based on a seasonal limestone mine and a continuous 40,000 to 60,000 tpy wood fired calcining plant designed to supply all of the quicklime needs of the Saskatchewan based uranium industry. Also described are the results of calcining and customer acceptance testwork on samples of lime prepared from recent Pinehouse limestone drill core. The potential benefits of the project include a significant new source of revenue for the community of Pinehouse, lower lime costs for the Saskatchewan uranium industry and employment for northerners in the mining, processing and wood harvesting operations.IntroductionInterest in the Pinehouse/Massinahigan River area for limestone was precipitated by the results of a 1977 industrial minerals drill hole program by the Saskatchewan Department of Mineral Resources. These results led to the acquisition of land in the area by Missi Island Mines Ltd who carried out extensive exploration during the period 1978-1982. They discovered a deposit on the southwest side of the Massinihigan River thought to contain approximately seven million tonnes of limestone with an average grade of 94.5% CaCO3. Missi Island carried out preliminary feasibility studies and prepared an Environmental Overview Statement. However, in spite of positive recommendations, the project was dropped in the mid 1980’s."

Jan 1, 2003

By Adam Moore, Peter Radziszewski, Matt Gallimore

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. In the context of the mining industry, interest in stirred milling technologies has grown over the last 20 years where the typical observation reported inDespite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills.At CMP 2014, one contribution was made to explore how mill design affects power and energy in a stirred mill. While the 2015 CMP paper explored the application of one scale-up methodology to the Gibraltar case. For the CMP 2016, the aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of the different scale-up methodologies used. This will be accomplished by first completing an overview of the scale-up models found in the literature followed by a review of the different testing and scale-up procedures. This review will be supported by a number of case studies found in the literature. The paper will close with a discussion on some of the challenges that these models and methodologies have and how future research might contribute to overcoming them.IntroductionStirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented (Stehr, 1988). The year 1948 saw the successful application of Du Pont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding."

Jan 1, 2016

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

By Phillip J. Mackey, Gerardo R. F. Alvear F.

It is now 38 years since the publication of the first edition of "Extractive Metallurgy of Copper" by Professor W.G. Davenport and the late Professor A.K. Biswas. The text book would be issued in a total of five editions, soon became the standard for students and those in industry. Interestingly it was published at the onset of great change in the industry. This was a time when sulphur dioxide controls in the USA were introduced, and almost simultaneously, world oil shocks caused significant increases in the cost of fuel - all leading to efforts to adopt new technology and move away from the reverberatory furnace, which had no potential for sulfur capture and required large amounts of fuel. At the time of publication of the book, new processes such as the Noranda Process and the Mitsubishi Process were in their infancy, while flash smelting (which was first commercialized in 1949 at Harjavalta, Finland) had made significant in-roads in boosting copper output, with some 22 new flash smelters licensed by 1976. Computer technology and associated process control techniques were rudimentary compared to systems today, available physico-chemical data remained largely in tabulated format and needed to be manually entered into the main frame computers of the era, while modeling techniques common today had not yet been developed. The copper industry has therefore seen immense changes since the time of this textbook: world tonnage of smelted copper has risen from 7.34 million tonnes/year in 1976 to 16.7 million tonnes/year in 2012, over a two times increase. Technologies such as the El Teniente Process, or Top Submerged Lance technologies, typified by the ISASMELTTM, not commercialized at the time, now treat large tonnages of copper concentrate in a single furnace. Advanced heat and mass balance software and thermochemical modeling are now used extensively to examine chemical and physical characteristics for process design and to support process optimization. These changes in the industry have been chronicled in subsequent editions of the book. This paper looks at the issues and problems seen in 1976 and over the intervening years, and compares this with the challenges facing the industry with the available tools and technologies today. Some ideas looking into the future are also discussed in the paper.

Jan 1, 2014

By A. F. Banks

"Potash processing has much in common in terms of unit operations and plant operating strategy with other mineral processing plants. As it is a rather large topic the processes will be broad brushed to give you some background and then I will go into a little detail on the things we do in the Cominco plant that may be of interest to the group as a whole. In particular the centrallized computer control system and associated instrumentation and the operator training programs will be covered as well as the mill fire, something that could happen in any plant. THE ORE AND PRODUCTSThere are differences in potash ores as you would expect. It is my intention to deal with the ores processed in the Saskatoon area. These are mined from the beds in the Patience Lake Member and have a mineralogical description as follows:Sylvite (Potassium Chloride) 40%Halite (Sodium Chloride) 55%Insolubles (Slimes) 5%A number of products are made from this ore. It is characteristic of a potash plant that you put as much effort into grading and converting the sylvite to meet market requirements as you do in recovering it."

Jan 1, 1976

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By Peter Cunningham

General Description of Projects The objective is to streamline data transfer within our Process Control and Business Systems for the purposes of tracking actual production, reducing manual record keeping, improving process control and improving vehicle maintenance. This presentation focuses on two implementations of mobile equipment data acquisition systems which make use of industry standard data models and data transport protocols. Pilots are part of the Mines Technology Roadmap to improve our mining operations ?Enabling technologies and pilot of key systems

May 1, 2013

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By Michael J. Kelly

IAMGOLD?s Westwood project is the site for the largest, by volume, bored vent raise in North America. When completed, it will be the fifth largest bored worldwide in a single pass. This paper will review the highest capacity raise drill system ever built (Redbore 100); as well as the technical difficulties in a single pass boring a 2,773 ft x 20 ft to 22 ft diameter raise. The difficult ground conditions and associated problems will be reviewed, as well as the solutions to overcome them. Use of the RVDS drilling tool to achieve .04% accuracy (14.5?) and the Geotube® water filtration system will also be covered.

Oct 1, 2010

By P. Tolvanen, A. Jalili

"When hard times strike in the mining cycle, sites tighten their belts and focus on lowering their unit costs. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. Faced with these requirements, site personnel must turn to areas where they can focus their effort for maximum return. For many sites, both in Canada and overseas, focusing on improving flotation cell maintenance is one of the areas where gains can be made for minimum outlay. Due to resource limitations and/or lack of equipment understanding, maintenance on many sites is only conducted on a reactive basis, once equipment fails. This paper will promote the idea that mineral processors should become more familiar with their equipment so they can ensure that the plant’s ability to produce is not compromised. By better understanding the flotation equipment and ensuring the critical components are maintained, it should be possible to unlock value in an operation. Flotation equipment inspections will be discussed in detail, including key items to look for during these inspections. Potential approaches for predicting wear and change-out time for flotation equipment components will be also demonstrated. An example of one approach used at a South African nickel site will be given.INTRODUCTIONWith metal prices decreasing and operating costs rising, concentrator operators are looking for ways to improve their bottom line. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. To meet the expectation of shareholders, mineral processors must turn to areas where they can get the best return for their efforts. One area where there is a large opportunity for improvement is in the maintenance of flotation equipment.On many mine sites, both domestically and around the world, it is quite common to see the philosophy applied of repairing equipment only once it has failed. Though some sites have advanced enterprise management systems and monitoring programs, in the authors’ experience, the decision on flotation equipment maintenance is rarely made on a proactive basis. Two common trends that are evident in the mining industry are that operations are under pressure to keep the plant producing, and maintenance managers generally have very strict budget targets to meet. In addition to these factors, few sites have a good understanding of the financial implications of running with worn or broken flotation equipment. Knights, Jullian and Jofre (2006) summarize this situation well, stating that the lack of correlation between some commonly used maintenance performance measures and key business drivers can lead to maintenance being seen only as a cost center (that needs to be reduced) rather than a tool for productivity improvement."

Jan 1, 2015

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By D. M. May

"Cut-and-fill mining is a stoping method that has been widely utilized in the mining industry over the past forty years. It took preference over shrinkage methods at Levack in the early 1930sbecause of its safety aspects; i.e., prompt support of the stope sidewalls, good working floors and better accessibility to support poor back areas. In addition, higher recoveries of ore were possible because of the flexibility of the method in that silling could take place easily at any horizon; low-grade ore could be sorted and left in the stope as fill and certain zones of rock could be left unmined. With modern techniques, a steady production rate can be established, as filling and mining can be carried out stimultaneously.AIthough there are numerous variations of cut-and-fill mining throughout the world, this paper reviews the original type of mining, with modifications and improvements through the years to present modern practices, with the Levack West operation appearing to be the most productive at this time. Stoping efficiencies have also increased substantially from the original 10 tons per manshift to the present 55 tons per manshift.The paper also outlines the many improvements that have been made with respect to mucking and ground support operations; from hand mucking in a single stope to the use of frontend loaders and haulage trucks in fully accessible stope complexes; and from timber props to roof bolts of various types. Although present methods are extremely satisfactory, experimentation is continually being conducted to improve safety and productivity for future mining.IntroductionThe major mining operations of the Ontario Division of Inco Limited are located in the Sudbury Basin (Fig. 1). Around the rim of this geological formation and within 30 miles of the City of Sudbury are nine producing mines and one ' open pit operated by the company .Ore production currently approximates 11.5 million tons per annum from underground and open-pit operations. Underground mining methods include sub-level caving, shrinkage, cut and fill, undercut and fill, blasthole and vertical retreat. The Levack Complex, the main plant of which is the central Levack Mine, produces 11,000 tons per day.The first prospecting in the Levack area, in 1887, was conducted by James Stobie, who examined rock cuts along the route of the Canadian Pacific Railway to the northwest of Sudbury. However, it wasn't until 1913 that operations commenced at Levack under the Mond Nickel Company."

Jan 1, 1981

By Zhuofei Yang, Jidong Kang, David S. Wilkinson

The fatigue behavior of AM60 high pressure die casting magnesium alloys was studied in a straincontrolled manner. The fatigue test was interrupted every 2,000 cycles for X-ray tomography scanning. The specimen was removed to be scanned on a desktop micro-CT system. The value of using X-ray tomography in a fatigue properties study was assessed with respect to porosity, cracks and fracture surfaces. The 3D analysis and model results showed porosity could be well measured and modelled in 3D. Defects bands are made of pores under 50 µm in volume-equivalent sphere diameter. Larger pores are randomly distributed in the region between two defect bands. Observation of cracks by X-ray tomography occurs in three ways such that the 3D model gives the best illustration of crack-porosity interaction while the other two methods have better detectability on crack initiation and crack tip observation. X-ray tomography is also of value in failure analysis on fracture surfaces. By summarizing X-ray tomography data during fatigue testing and observing fracture surfaces on a 3D model, a better understanding on the crack initiation, crack-porosity interaction and the morphology of fracture surface is achieved.

Jan 1, 2014

By Mary Ann Bennett, Val Nichols, Colleen Proctor

"In 1997 when Royal Oak Mines Inc. went into receivership, the mineral processing technicians (mill operators) who had been working at Giant Mine in Yellowknife, Northwest Territories for most of their career walked out with no credentials to serve as testimony of their knowledge and skills.As a result of new diamond mining activity and the establishment of socio-economic agreements, mining industry representatives approached the Department of Education, Culture and Employment (ECE), Government of the Northwest Territories, in 1999. They requested support and direction to promote training and recognition for mineral processing technicians at BHP’s (BHP Diamonds Inc.) Ekati mine. ECE recommended the development of occupational standards and certification.This paper describes the development process and end products that resulted from this collaborative project between industry, government and education. In addition, industry representatives involved in the project share their views on the development process and the benefits of standards and certification.The conclusion invites industry members to support national occupational standards and certification with their associated benefits: standardized training in the workplace and institutions, proof of competence for hiring, recognition of prior learning, and a nationally and internationally recognized credential.INTRODUCTIONSwiftly changing labour market demands are nothing new in the North. The fur trade and mineral discoveries have brought employment to workers in a feast and famine cycle for decades. In the late 1990s, the Giant, Con, Lupin, Polaris and Nanasivik mines were nearing the end of productive runs. Many experienced workers found that without credentials, they had no proof of their abilities to offer prospective employers."

Jan 1, 2005

By Samuel Frimpong

The interaction of oil sands with a ground articulating pipeline (GAP) system has been simulated with the dynamic model established in this work by combining the multi-body and soil dynamics with the Automatic Dynamic Analysis Mechanical Systems (ADAMS) software. Mathematical models governing the interaction of the GAP system with the oil sand terrain have been modeled based on the theory of multi-body and soil dynamics. These models consist of GAP track-oil sand contact model for generating the contact force between oil sands and track and load-deformation oil sand model for capturing the dynamic behavior of oil sands. A virtual prototype has been created and simulated in the ADAMS environment. The simulation result of the effect of load on oil sand deformation indicates that maximum deformation value increases non-linearly with load varying from 0 to 60t. This study provides a solid foundation for further research and the GAP technology development.

May 1, 2004

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004