Search Documents

By A. D. Misener

Introduction Temperature gradients have been determined for numerous locations in the Canadian Shield in connection with mining operations (1, 2, 12, 13, 14, 15). As part of a programme of geophysical studies of this region, some of these gradients were re-determined by the writer at locations where other thermal properties, specific heat, thermal conductivity, radioactivity, etc., were also to be measured. The ultimate object was to determine the heat flow to the surface at these locations. It was felt that the practice of determining heat flow from the temperatures and conductivities obtained in a single vertical bore hole (3, 4, 5, 6, 7, 8, 9) might give results which were appreciably divergent from the average for a considerable area. Particularly, it was thought that temperature gradients, whether obtained in a single vertical hole or from a number of random locations at various depths in a mine, might be subject to local variations and anomalies serious enough to render unsure any discussions based on them. The procedure followed in this investigation was to select a location where mine workings extended to considerable depth over a reasonably wide area. At selected depths below surface, horizontal drill holes extending into regions of undisturbed rock were located and resistance thermometers were inserted into these holes far enough to record the true rock temperature. An attempt was made to obtain a sufficient number of readings at or near any one level to give a representative coverage of the area selected. This ideal could not always be attained, but the large number of readings obtained for each are a does give a reasonably representative picture of the temperature conditions. These readings required much rime and movement of men and equipment underground . They could not have been obtained without the wholehearted co-operation of the management and considerable assistance from the personnel of the mines concerned.

Jan 1, 1949

By Donald Carlisle

"IntroductionTHE OPINION is held by many persons outside the mining industry, and by some within it, that mine •operators customarily find it advantageous to mine •only the richer parts of orebodies and to leave behind, perhaps permanently, leaner material which could be mined only at a lesser profit. This opinion and the inference which might be drawn from it that 'gutting' of mineral resources is a common feruture• of the mining industry are prejudicial to the intertsts of the industry and deserve careful scrutiny. Oddly enough, a theory of mine economics which gives much support for the opinion was advanced first by members of the mining profession itself, has been repeated •several times in mining literature, and to my knowledge has never been adequately refoted.According to the theory, selective mining of the rich ore first on a large scale will yield substantial gains and these gains do not merely reflect the desire of 'money minded investors' for a quick return but derive from the logical application of compound interest rates and the concept of ;present value. W. O. Hotchkiss and R. D. Parks (1) illustrate the reasoning with a hypothetical example in which an orebody of 4,000,000 tons may be mined either in its entirety in forty years at $1.00 per ton profit or selectively with the recovery of only the richest half in twenty years at $1.50 per ton profit. They show that, with Hoskold rates of 4 and 8 per cent, the present value of profits from mining only the richer 2,000,000 tons exceeds the present value of profits :from mining the whole orebody by about 20 per cent."

Jan 1, 1953

By W. J. Dick

THE purpose of this paper is to point out, briefly, the importance of the coal mining industry of Alberta and to stress the economic factors that hinder its development; also to offer suggestions relating to the major problems of the industry. The minor problems will not be dealt with in detail, because, if the major problems are taken care of, it is felt that the industry itself can take care of ,he remainder. COAL MINING NO LESS IMPORTANT THAN GOLO MINING The large increase in metal mining development in all provinces of Canada, excepting Saskatchewan, Alberta, and the Maritimes, has had the effect of focussing public attention on this branch of the industry. The fact, also, that this development came at a time of depression has been of immense benefit to Canada as a whole. On account of the necessity and consequent demand for gold, with its attendant increase in price, through government action, from $20.67 per ounce to $35.00 per ounce, it is safe to say that the public of Canada have become, today, gold mining conscious. While everyone admits the great value. of the gold mrn111g industry, nevertheless, the equal value to Canada of certain other industries must not be lost sight of. The coal mining industry, in particular, is worthy of greater public and government support than has been accorded it in the past. It would seem unnecessary to stress this matter to a meeting of the Canadian Institute of Mining and Metallurgy, but unless certain facts are brought to your attention, there is danger that the coal mining industry will not be developed to the extent its national importance deserves. Too many public men and men in authority are unaware of the value of coal mining.

Jan 1, 1936

By J. C. Loretto

"OPENING REMARKS Yesterday and today we have heard some very interesting papers on operating matters and some of you are probably wondering what we are now doing talking about Communications in Plant Design. Let me tell you! Before the techniques we have heard being discussed can be used, there has to be a properly operating plant. It is certainly a fact that many mineral processing plants achieve only limited success and a number of them can even be said to be failures. Some of you sitting here are probably living with operating problems that are clue to errors in the design.If the histories of these problem plants are examined, it will be found that in many cases, the necessary skills were available during the period of the plant design. There was extensive operating know¬ledge together with a full range of project expertise. Why then the failures? In a substantial number of cases it can be traced to the old, old problem of communications. As plants get bigger, money costs more and smooth startups become more important, it becomes less and less economic to fix up any design errors during plant operations.During our careers in mineral processing, nearly all of us will be involved in at least one plant design and I feel that it is as well if we understand some of these communication difficulties that can lead to a problem plant. There is little point in us being experts in mineral processing if the knowledge we have acquired doesn't somehow get incorporated into the plant.I would, therefore, like to present this short paper that mentions a few of the significant communication problems that can occur during the design of mining and mineral processing plants, together with some thoughts on answers to these problems."

Jan 1, 1973

By M. M. Williams

WESTERN CAN ADA'S coal industry has experienced a serious set-back since 1949, following a pattern well known to its counterpart in the United States. The loss in coal markets in Western Canada has been particularly severe as the discovery of large reserves of oil and natural gas and the subsequent construction of re-fineries and pipelines roughly coincided with the dieselization of both main railways. While the coal industry will have to face a further decline in markets of long standing, others with a large growth potential can be se-cured if present marketing methods are changed where needed and if fundamental and applied research programmes are actively pursued. The energy and chemical potential of Western Canada's coals will eventually find their place in the ever-growing needs of industry and electric power producers. Electric power generation would appear to offer the largest and most immediate market for coal. If the coal industry is to serve this market adequately and gain as much of it as possible, coal operators ? must have a good knowledge of certain characteristics -of the electric utility industry and its fuel requirements. This paper is prepared primarily to set out some of these characteristics, but also discusses other probable markets for coal.

Jan 1, 1958

By J. E. Hawley

Abstract Spectrographic methods for the analysis of minor constituents such as platinum-group metals, gold, silver, and silica in palladium and platinum refinery sponge are described. These involve the conversion of the sponge metals to the black form by reduction with high purity aluminum filings in either acid or alkaline media. Standards of known composition are prepared in the same manner from either refinery or spectrographically standardized sponge metals. Samples of the black metals are mounted in pellet form and a multisource spark discharge used for excitation. The range of concentrations of impurities studied are those common to refinery samples. Excellent reproducibility of intensity ratios using major constituents as internal standards, is demonstrated and two methods have noted by which the accuracy of the procedures are shown to be of the order of 3 per cent, on the basis of synthetic preparations. Introduction During the past two years an investigation has been carried out in the Spectrographic Laboratory, Queen's University, to determine the suitability of modern spectrographic techniques for the precise analysis of the platinum-group metals palladium, platinum, rhodium, iridium, and ruthenium in the form of refinery sponge analyzing about 99 per cent of the major constituent.

Jan 1, 1951

By K. J. R. Ford, Botz. M. M.

Porphyry copper ores are frequently a source of low-grade gold ore, but gold in these ores is often associated with significant levels of cyanide-soluble copper. Cyanide leaching of such ores increases flowsheet complexity and operating costs, and requires thorough planning to satisfy environmental requirements for tailings disposal and mine closure. This paper presents a review of the chemistry of cyanide leaching of gold-copper porphyry ores, carbon adsorption phenomena and means of removing base metals from leach solution. The primary economic drivers behind the processing of such complex ores are also analyzed.

Jan 1, 2011

By C. H. Wright

Introduction The rapidly expanding and increasingly complex Canadian industrial structure, with the mining, metallurgical, and chemical industries as a large integral part, has, in recent years, brought greatly increased importance and value to our industrial minerals. In the modern economy of our mineral industry the importance which is due the non-metallics has been somewhat overshadowed by the great value of our large metal production and, in addition, by the glamour and fascination usually associated with the mining and treatment of gold ores. The term 'Industrial Mineral' is used in this paper in its usual sense and refers to non-metallics other than fuels. Coal and petroleum products, including natural gas, are considered as industrial minerals in those applications in which they are used for strictly chemical process purposes. Certain reduction metallurgical industries are so closely allied to chemical industries that for purposes been of this discussion no attempt has made to differentiate between them. Chemical industry in Canada today is a fairly large factor in our national economy, whereas in 1898, when the Canadian Mining Institute was born, it was very small indeed. Chemical concerns are largely dependent on industrial minerals for raw materials and process supplies and, as the country has developed industrially, so have the demands for non-metallics increased, not only by chemical industry but also by other large consumers, such as the construction and metallurgical industries. At the present time there is a greater than normal incentive prevailing for new discoveries, due to the serious lack of balance that exists in our import and export trade. This fact has resulted in intensive efforts to rectify the situation by locating new deposits and re-assessing those already known in an effort to enlarge and improve our home production of raw materials and also to extend their processing in Canada for our own needs and for export. The rapid advances in science and technology that have taken place since 1900 have also resulted in many cases of beneficiation and utilization of otherwise too low grade materials in order to satisfy current demands. The purpose of this paper is to indicate the history and the trends of the utilization of industrial minerals in established industry and to indicate the important part played by non-metallics in connection with the opening up of new industries. Some consideration has been given to the continual competition between natural and 'synthetic products and to the general tendency towards more rigid specifications.

Jan 1, 1948

By J. E. Udd, L. P. Geldart, B. B. Dhar

"Solutions for the stress distributions around simulated underground openings have been limited to calculations of boundary stresses for simple openings in which the boundaries may be expressed in mathematical terms. Studies involving circles, ellipses and ovaloids are re-ported in the literature.The stresses on the boundary of an opening and those at a distance from it in the medium are of concern to the engineer. The former may be related to the greatest concentrations of stresses encountered; the latter have a bearing on the identification of the ""zone of influence"" of the opening.Recent advances, in the form of a derivation for the stresses at a distance from an opening of elliptical shape, together with a solution derived previously for stresses in depth around ovaloidal openings, have been combined with computer programming techniques to provide complete solutions for a wide range of cases and variables. Some typical results which, it is hoped, may have some application to the design of underground openings are given herein."

Jan 1, 1970

By M. J. Beus

Many mines in Canada, the United States and South Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due to the excessive weight. It has been suggested (DeLorme, 2000) that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm (13/4 in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg (10 ton) skip could exceed the safety factor of the rope. To improve on the current understanding of the mechanical behaviour of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modelling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca, 1999), is used to simulate the structural behaviour of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modelling on the wire rope will be discussed.

Jan 1, 2002

By Rocky (Yaokun) Wu

This paper introduces the development and application of a new cable anchor - Cable-Lok for pre-stressed cable bolting in mines. Cable-Lok is a spring-loaded cable anchor suitable for the drill hole diameter of 50 and 65 mm (2" and 2.5") in medium soft rock to hard rocks. The cable anchor is automatically set on installation and the cable can be tensioned immediately to provide active and primary support throughout its length. Post-grouting can be conducted independently. In comparison with the conventional cable bolting, Cable-Lok anchor will greatly speed-up the cable bolting circle and decreases the cost of cable bolting. Cable bolting anchored with Cable-Lok anchor has wide application in mines, e.g. pre-stressed cable bolting in large span drifts and intersections for permanent rock support, or in hanging walls or stopes for temporary support, or cable lace anchoring etc. This paper introduces the principle of pre-stressed cable bolting and the specifications of the Cable-Lok anchor, presented the testing results in laboratory and the application cases in mines.

Oct 1, 2010

By E. C. Grunsky, B. W. Smee

"The development of low-cost, rapid multielement analytical techniques has generated large geochemical databases in many exploration programs. When a sampling program consists of several thousand samples, the resulting data matrix is enormous and effective interpretation using all of the elements individually becomes burdensome. However, the application of multivariate statistical techniques can extract geochemical patterns related to the underlying geology, weathering, alteration and mineralization. Imaging the results over topography enhances the interpretation of these patterns. Examples of this approach are shown from mineral exploration programs in Canada and Mexico. IntroductionThere has been a dramatic change in the effectiveness of using geochemical survey data in the past ten years. This is mostly due to:• lower cost of geochemical analysis;• lower detection limits;• new methods of multi-element analysis;• a marked decrease in the turnaround time;and• the intelligent use of computers in presenting geochemical data.Geochemical surveys commonly have two objectives: locating abnormal concentrations of ore-forming or pathfinder elements and characterizing the underlying host lithologies. Geochemical surveys often employ a wide range of sample media that may typically include whole rock lithogeochemistry, various soil horizons, till and basal till sampling, stream sediments, lake sediments, and various forms of weathered regolith. Each of these sample media will exhibit a unique element distribution that must be factored in the interpretation phase of a geochemical survey study. This can become a cumbersome process if univariate data handling methods are employed."

Jan 1, 2003

By Oliver C. Ralston

DURING the development of froth flotation for the treatment of sulphide ores, a certain amount of information was collected about a few of the nonmetallic minerals, and occasionally the gangue minerals in the sulphide ores showed an embarrassing tendency to float. However, for many years efforts were expended to develop reagents that would cause wetting and depression of these minerals. Among the nonmetallics, the minerals sulphur, graphite, and talc probably should be classified as 'natural floaters', and perhaps sericite. They respond to almost any type of flotation reagent, and their beneficiation by flotation had been attempted years ago. Flotation of sulphur is now common practice, and graphite was concentrated during the World War in many mills, most of which have now closed down. A talc mill has just been constructed, and another may soon be erected. Second to the 'natural floaters' come the 'easy floaters', cassiterite, fluorite, barite, mica, colloidal gangue, and paper pulp from white water of paper mills. That these materials responded to some of the early flotation reagents, as oleic acid, has long been known; occasional references to their behaviour are found in the very early flotation literature and in that of today. In general, however, nonmetallic minerals, valued at $2.00 to $15.00 per ton, have for a long time been regarded as cheap products and not worth much beneficiation. Consequently, only high-grade natural deposits suitable for direct mining and sale have been gouged out. Furthermore, the mining of these minerals has too frequently been in the hands of 'super-practical' men-men of no technical or other training, willing to work for a very low compensation. From the social standpoint, nonmetallics has been the field for small, untrained enterprisers with little money to spend on plant or equipment. But times have been changing. The impact of technically trained men on the old industry has revealed appalling losses and inefficien-cies and proved the value of processing materials discarded or avoided by the old regime.

Jan 1, 1937

By Maryam Sadeghi, Jonathan Roy, Claude Bazin

"The operation of mineral processing equipments is intimately related to the mineral composition of the ore. However unit performances are usually characterized in terms of metal contents or recoveries as this data is easier to obtain than the mineral contents. This paper describes a method that combines the operations of material balancing and estimation of the mineral contents of the ore. The estimated mineral contents can be used for process analysis and diagnosis of operating problems.IntroductionThe ore that is feeding a concentrator is made of minerals that condition the energy requirements for the ore comminution and the performances of the subsequent separation circuit. Indeed a change in the mineral composition of the ore may lead to lower grinding mill throughput as well as lower recovery or grade of the economical products. Despite this relationship is recognized the mineral composition of the ore is seldom measured or estimated to provide regular information for the diagnosis of operating problems. Some methods such as the QEM-SCAN (Whiten, 2008; Lamberg and Vianna, 2006) are available to measure the concentration of the minerals in ore samples but the method is time demanding and plant operators usually base their evaluation of the plant performances on chemical assays of metals or elements since this data is easier to obtain from ore samples.Usually samples of the streams of mineral processing plants are collected on a daily basis to be assayed for strategic elements. The obtained concentrations are balanced to produce coherent data with the material conservation constraint and then used to characterize the day to day operation of the plant in terms of recovery of valuable metals and grades of the marketable concentrates. The behavior of contaminant elements can also be monitored from this data allowing the operators to explain for instance a lower zinc concentrate grade by a more important contamination of iron. However such diagnosis is only partial as the contaminant element can be transported by different minerals. Indeed the iron contamination of a zinc sulfide concentrate may be caused by an inadequate depression of pyrite or due to another iron carrying mineral. A possible way to answer the question is to determine the concentrations of the various minerals in the ore and produced sealable concentrates. Since measuring the mineral contents of the ore could be a demanding task one should consider to estimate this data from the daily chemical assays of the sample collected on the main streams of the circuit. Some authors have already investigated the problem. Whiten(2008) described a method to estimate the mineral contents of an ore sample. Lamberg and Vianna(2006) proposed a method to do a sequential mineral reconstruction followed by a material balance. Few of these methods account for the mass conservation of the reconstructed mineral contents."

Jan 1, 2016

By I. S. Parrish

The Sullivan Mining Group has been exploring the mineral deposits of the Mount Pleasant area of southern New Brunswick since 1967. Sullivan geologists have logged over sixty miles of drill core, mapped over five miles of underground workings and studied numerous surface exposures. Several mineralized zones have been defined and two higher-grade porphyrytungsten bodies delineated. Within these bodies, wolframite occurs as disseminated specks and grains up to one-half inch in diameter. The host rock is a brecciated rhyolite porphyry that has intruded quartz-feldspar porphyry of Mississippian age . The host rock is itself intruded by an acid porphyry called transition rock and is underlain by a microgranite. The mineralized zones, host rock, transition rock and microgranite are all thought to be derived from the same magma, and to represent progressive fractions from that magma.

Jan 1, 1978

By D. C. Kaliampakos, A. G. Benardos

The existence of quarries near or even within the boundaries of urban centres is the cause of many environmental problems, despite their significant contribution to the cities’ development. Hence, the question arises as to how quarrying activities can be compromised within the spirit of sustainable development in big cities. In the case of Athens, two dominant, though opposite opinions have been formed. The first argues that all quarries must be forced to suspend their activities as soon as possible; the second presses for the continuation of quarrying. Consequently, the question is transposed on the dilemma between improved environmental conditions and economic development. This paper demonstrates that if a complete redesign is employed to specific, nonvisible quarrying sites, the continuation of quarrying activities is acceptable. It is a good compromise between the economical demand and environmental protection.

Jan 1, 2000

By W. H. MacLean, S. Liaghat

Abstract- The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographie means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8% carbonate, 60Jo chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/Ybn. = 1.7 to 2.8, Si02 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y =9, LaN/Ybn. = 4 to 8, Si02 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of Fep3 (27% total iron), Si02 (14%), CaO (8%), S and K20 ( + 2%), were added, Na2O was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

"Each and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Several factors including ore heterogeneity and harsh production environment affect the reproducibility of the reported data. Best practices of metal accounting thus prescribe that production reports be accompanied by measurement quality reports quantifying the reproducibility (a data quality metric often expressed as a relative standard deviation) of each data reported. Ignoring the irreproducibility of measurements may lead to the perception that random errors have been totally eliminated through statistical data reconciliation, which is wrong. This paper aims at explaining the full lifecycle management of reproducibility estimation from the outset at the measurement process to its reporting after having been through the statistical data reconciliation process. Indeed, the reproducibility of reported data can be obtained by performing a sensitivity analysis. Necessary conditions for obtaining a truly representative assessment of measurement reproducibility are stated. Typical levels of measurement reproducibility found in operating flotation plants are also reported. These numbers can be used as benchmarks for reproducibility levels that can be realistically expected.IntroductionEach and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Such production reports are the most expected output from a metal accounting system (MAS). The duly recurrence of this task combined with an insufficient level of automation has somehow contributed to the misleading perception that it is mainly a clerical work. However, as shown in Figure 1, a MAS encompasses way more than just a reporting system. Acknowledging that the content of production reports indubitably origin from raw measurements has important implications for how both the reports and MAS should be monitored."

Jan 1, 2016

"Under the term ""paleogeomorphology"" are grouped together all geo-morphological phenomena which are recognizable in subsurface geology. Since geomorphology is the science of the earth's relief features, paleogeomorphology is the science of buried relief features. Such features are of importance to the petroleum geologist whenever they lead to the trapping of hydrocarbons. In areas where these features abound -and western Canada certainly is such an area -pale-ogeomorphology ranks in importance with stratigraphy and structural geology as a hydrocarbon-finding tool. Hydrocarbons may be trapped either directly or indirectly due to paleogeomorphological processes. Both types of traps may occur either below the morphological surface or above (against) it. Several examples of types of paleogeomorphological traps are given. A new classification of geomorphological .features is proposed, with a subdivision into two main groups: constructive and destructive geomorphic processes. Of the many geomorphic classifications, some are of greater interest to the petroleum geologist in western -Canada than others. In the present paper the morphology of reefs and of buried erosional land forms are discussed in greater detail. In dealing with the reefs of the Devonian Leduc formation in Alberta, it is found that several groups of reefs can be distinguished and that each group presents a separate set of morphological characteristics. The effects of erosion and weathering are exemplified mostly in the Devonian, Mississippian and Jurassic of Alberta, Saskatchewan and Manitoba. Hydrocarbon traps occur below the highs on the erosional surface as well as in sands laid down in the lows of that surface. The rules which govern the formation of ancient landscape forms are worked out, using an area in southeastern Saskatchewan as an example."

Jan 1, 1960