Search Documents

Don Hausen was a pioneer in the field of quantitative mineralogy. Methodology that he developed at Newmont almost 40 years ago is still employed today, only the technology has advanced. Petrographic methods were stressed with an emphasis on alteration, mineralisation and paragenesis. Methodologies employed by Don on the Carlin deposit were applied to developing the Carlin Trend by helping to work out lithology and structure, which ultimately led to the discovery of deep high-grade deposits. Quantitative methods used by Don on San Manuel, Copper Creek and Superior, Arizona were applied to the development of the Batu Hijau Deposit in Indonesia. Advancements in technology since DonÆs time have made the mineralogist much more efficient. Manual measurement of peak heights off of strip charts for semiquantitative XRD has been replaced by software that does Rietveld refinement and whole pattern fitting. Hand contouring of XRD data has been replaced by digitised data incorporated into geologic models. Optical point counting, which would take a dayÆs work to process 1000 points, has been replaced by automated SEM methods where 20 000 points are possible in an hour. The use of the optical microscope remains relatively unchanged, and still remains as Don emphasised the æeyesÆ of mineral exploration. However, the information can be relayed much more quickly with digital image capture and electronic data transfer. Don insisted on becoming involved in projects at the grassroots level and supporting the project through mine closure. This made the mineralogist a liaison between exploration geologists, mine geologists, metallurgists and mine engineers. The methodology that Don helped develop continues to provide invaluable support to Newmont geologists and metallurgists worldwide today.

Jan 1, 2008

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the 'furnace free' conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

By K C. Corin, N Ndamase, M Tadie

Mining operations in arid regions are compelled to reduce their consumption of fresh water. Closed water circuits are an attractive solution and, in addition to reducing freshwater consumption, have the added benefit of reducing reagent consumption as well as the environmental impact by eliminating effluent discharge. Accumulating ionic species have been shown to hinder collector adsorption which reduces the recovery of valuable minerals. Numerous studies have investigated the effect of degrading water quality on collector adsorption however there is very limited understanding as to how this takes place from an electrochemical perspective. This study therefore aims to investigate how the presence of accumulating ionic species at varying concentrations affects the electrochemical adsorption of sodium ethyl xanthate onto galena. The synthetic plant water used in this study comprised of single salt solutions to isolate the effects of the ionic species of interest. The ionic strengths were varied between 0.0242 M, 0.0727 M, 0.1212 M and 0.2426 M which correspond to University of Cape Town (UCT) Centre for Minerals Research (CMR) synthetic plant waters of 1, 3, 5 and 10SPW, respectively. Mineral rest potentials indicated how changing water quality affected xanthate-mineral interactions. Microflotation observed the impact of changing water quality on mineral floatability.

Aug 24, 2022

By D Cai, E Baafi

Various enabling technologies and systems have recently been introduced in the mining industry. Such systems include miner-bolters with concurrent cutting and bolting, employment of two shuttle cars, adoption of self drilling bolts and utilisation of continuous haulage or monorail systems. The paper discusses how Flexsim discrete event simulation models were used to assess how these proposed mining systems can best be used to achieve and sustain high roadway development rates of 10 m per operating hour for 20 h/day.

Sep 26, 2011

By Crawford M

During the initial development of Mount Isa Mines power was supplied from a temporary power plant situated near the Man & Supply Shaft. The main power plant was placed in service early in 1931 and then comprised two Babcock and Willcox boilers, fired by pulverised fuel, and two British General Electric Company's turbo-alternators of 5,000 kW. each. Both plants have been described by A. F. McAskill in the Journal of the Institution of Engineers, Australia.From 1931 power demand progressively increased due to greater production, further mine development in the harder sulphides increased pumping for mine drainage and additions to mill and smelter until, by 1935, the plant was inadequate for further output commensurate with a reasonable safety margin.Coincident with the added power demand, operating conditions involved a fuel problem which could not have been anticipated. The ash content of the fuel supplied gradually increased from 13% to 16-5%, while the melting point of the ash decreased with higher pyrite content.Temperature conditions in the furnace required careful control to cope with ash formation and slag accretions.Consequently brickwork, excessively stressed on water walls, was constantly under repair, and required suspension periods of 50% of operating time for cleaning and overhaul.Load conditions varied continually, therefore the high heat liberations in the furnace, necessary to accommodate peaks in fluctuating output, resulted in ash fusion.

Jan 1, 1939

The constructionhunnelling industry in Hong Kong has taken an upturn during the last few years due to the commencement of works to relocate the International Airport to Chek Lap Kok Island. The Airport Core Program consists of ten individual projects including roads, landfill, bridges and tunnels to build the airport and link it to the mainland of Hong Kong. Part of one of these projects is Cheung Ching Tunnel located on Tsing Yi Island. The proposed tunnel consists of a 1.6 km twin tube road tunnel through the island's central ridge, taking three lanes of traffic each way. Each tunnel is 16 m wide - (the widest road tunnel in Hong Kong) and are 10 m high. ICI Explosives (China) saw an opportunity to supply bulk explosives to the Cheung Ching tunnel and contacted ICI Australia to determine availability of a bulk system for tunnel blasting, and assist in its introduction. This paper discusses the methodology behind developing that bulk system to suit a large tunnel drill and blast operation. It also looks at the problems encountered along the way, from the development of the product to the application of the system in the tunnel and the eventual success of introducing a bulk system into a large tunnelling project.

Jan 1, 1994

Australian coal mines have spent considerable capital on dragline improvements over the last two years. This has included ~$30 M on UDD conversions, >$20 M on new buckets, boom upgrades, electrical upgrades, etc. This is a natural part of the response of mining companies to technology and replacement programs. Capital expenditure is a normal part of the ongoing success of most companies. There is however, a tendency for some people to rely on the capital alone to provide the ongoing improvements in equipment productivity. Implementing new technology through capital expenditure is only part of the equation in continuous improvement. For 80 - 90 per cent of the year, the operator controls the productivity achieved by the dragline. Variation between operators is huge. The average standard deviation in productivity is 12 per cent and maintenance impact is over 40 per cent. Robbins 2003, states: Contrary to what we were taught in grade school, we werenÆt all created equal. Most of us are to the left of the median on some normally distributed ability curve. Further, he states: The issue is knowing how people differ in abilities and using that knowledge to increase the likelihood that an employee will perform his or her job well. There are two options for reducing variability between operators; improving operator ability and getting the machine to take over what the operator is doing (automation). Dragline automation will be discussed, however, this paper will focus more on the æhuman factorÆ and how to establish a dragline with minimum variability between operators.

Jan 1, 2005

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M T Roche

The Cannington deposit is one of the largest accumulations of silver-lead known. Located 135 km southeast of Cloncurry in North West Queensland (Figure 1), Australia, the deposit is currently in the feasibility stage of its development. The deposit is named after the nearby Cannington Pastoral Property which runs some 25 000 sheep on 'downs' country. The investigations of the Cannington deposit are carried out under the authority of Mineral Development Licences 139 and 144 and Exploration Permit for Minerals 6788, Answer Downs. Exploration for Broken Hill Type (BHT) silver-lead-zinc deposits in the Mt Isa region has been undertaken by The Broken Hill Proprietary Company Limited's Minerals Division (BHPM) since the early 1980s following in-house research which showed that the Eastern Succession of the Mt Isa Block exhibits characteristics which were favourable for hosting BHT

Jan 1, 1994

By E R. Ramanaidou

Two unknown iron ore samples were found by a geologist from Ok Tedi Mining Limited copper, gold and silver mine at an old wharf site dedicated to a 1970s drilling program in Lake Murray in Papua New Guinea (PNG). These iron ore samples could not come from a PNG mine and it was decided that a study should be undertaken to understand their origin. Lake Murray is the largest lake in PNG with a total surface area of 647 km2. It has a high-water 2038 km long convoluted shoreline with seasonal water level changes (Osborne, Kyle and Abramski, 1987) and it is located around 200 km south of the Ok Tedi mine (5°13’25”S, 141°09’37”E). The petrology, mineralogy and chemistry of two Fe samples (Ok Tedi 1 and Ok Tedi 2) included optical microscopy, X-ray fluorescence (XRF) analysis and a comparison with worldwide iron ore deposits. The two rock samples were cut to produce two subsamples: (1) a polished thin section; and (2) a pulp that was used for XRF analysis including major, minor and trace elements. Ok Tedi 1 and Ok Tedi 2 were petrologically and chemically compared to a range of known iron ore samples from Australia, Brazil and South Africa. The petrological study of Ok Tedi 1 indicates that it is composed of granoblastic recrystallised hematite and the overall texture is uniform without any obvious original ‘sedimentary’ texture. Ok Tedi 2 is a ‘specular’ or platy hematite with recrystallised and fused grains. Using both petrological and chemical clues, the two Ok Tedi samples likely originated from the Iron Quadrangle in Brazil.

Sep 18, 2023

By A Turichshev

The synthetic rock mass (SRM) approach for modelling jointed and veined rock has been at the forefront of caving geomechanics research for years. A well-constructed and calibrated SRM model can capture the full rock behaviour at a macroscopic scale. Traditionally, SRM technology employed bonded particle models (BPM) due to their ability to model rock’s response to loading without prior specification of behaviour. The SRM modelling process requires the BPM to simulate intact rock and the subsequent introduction of fractures or veins by changing bonding characteristics between the particles. However, bonded particle materials have difficulty reproducing both the compressive and tensile strengths of intact rock. This and other limitations of BPM have been the driving force in exploring the potential of grain-based (2D) and bonded block (3D) models (BBM).This paper reports on recent work exploring the applicability of both BPMs and BBMs in 3D to the modelling of intact rock. The advantages and limitations of both BPMs and BBMs are addressed based on the results of numerical simulations using the PFC3D and 3DEC distinct element codes. The preliminary results suggest that BBMs are better suited for simulating intact rock behaviour than BPMs. Ongoing work aims to better qualify the applicability of BBMs under different conditions. This has significant implications for our understanding of rock mass behaviour in a caving environment.CITATION:Turichshev, A and Hadjigeorgiou, J, 2016. Simulating intact rock behaviour using bonded particle and bonded block models, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 453–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The design of the grinding section is discussed and details are given of the equipment installed for the autogenous grinding of ores from the C.S.A. mine at Cobar.The first section of the concentrator commenced treating ore in June, 1965 and operating experience and maintenance requirements since that time are outlined.

Jan 1, 1969

By Pease JD

This paper reviews the changes in operating practices made in the heavy medium plant to meet the objectives of increased silver, lead and zinc production at lower operating cost. The effects of medium quality, screen- ing efficiency, medium consumption, equipment service life and plant availability on these objectives are described.

Jan 1, 1988

By P Ormsby, T Hewitt

Ore in pillars constitutes a significant proportion of the ore reserve at PasmincoÆs Broken Hill Mine. Many of these pillars are narrow (5 -6 m) and high (16 û 35 m) vertical blocks. High-grade ore has been left between primary horizontal cut and fill stopes. These stopes were mined from the late-1960s until the early-1980s. Fill material is a variety of hydraulically stowed sand, sand-cement, and remnant timber support. Many pillar cut-throughs were made between the old stopes. In order to gain access for the current pillar recovery operations, it has been necessary to develop pillar drill drives through, and adjacent to, the hydraulic filled stopes. Whilst long hole recovery of vertical pillars is not new, some notable successes using innovative ideas have been achieved during 1997. These innovations include:The use of steel mesh reinforcing in shotcrete when mining through, or adjacent to, hydraulic fill. Construction of steel sets to support vent rises and haulage ways encountered in the cut-throughs. The use of ground movement monitoring equipment. Survey lasers with chain droppers and convergence monitors were installed in the 18 Pillar to detect any movement of the pillar block and decrease risk to personnel. The development of a three-dimensional computer model of primary stoping, using Vulcan software, to assist in the design of pillars. Maximisation of recovery using different drilling and firing practices.

Jan 1, 1998

Contracts are widely used in mining to provide self motivation in an environ-ment of isolated work places. Which incentives to use and how to implement them has long been the subject of numerous discussions. The mines operated by Australian Mining and Smelting at Broken Hill have evolved several guidelines to follow when developing contracts.Identify the main purpose of the work and use this as the basis of measurement for the contract. Therefore stoping achievement would be measured by tonnes extracted, development by metres driven. Paying for other work activities such as standing timber in timber stoping must detract from the percentage of the total contract paid per tonne produced. Concentrating on the main activity and applying the majority of contract pay to that task reinforces at is beneficial to both the miners and the whole operation.

Jan 1, 1985

By Aust M. I E

IT is the custom, I must admit, for a presidential address to be a review of the progress during the year of the institution presided over, and of the sciences and arts within its ambit. On this occasion precedent is departed from in favour of a subject by request.As man has at last, in employing gravimetric and electrometric methods of subsurface research, started on the rational use of divining rods with some knOWledge of their governing laws and principles, and with some ability to interpret the results obtainedfrom them, I was asked to add to the voluminous literature of the quack or empiric divining rod. James Mansergh, the author of Melbourne's sewerage system, in his presidential address before the Institution of Civil Engineers in 1901, admitted he was afraid touse the hazel rod lest in sinking on its indications to some solution.

Jan 1, 1928

Average annual growth in consumption of primary energy in Australia over the past ten years has been 5.5% compared to a world average of 4.1%. Over the next ten years growth rate is expected to increase to 6% per annum due largely to the rapid development in the mineral processing industry. By the end of the 1970's natural gas is expected to supply more than 9% of Australia's, primary energy market. Coal will supply 40% and petroleum products 47%. Nuclear energy will make its appearance but-will only make a small contribution in the period. Australia has adequate reserves of natural gas and coal to supply its needs in the 1970's and beyond. However the newly developed reserves of crude, while supplying 60-70% of requirements-in the initial years; will need regular and sizable additions if they are to .keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated *that new discoveries-will need to approximate. ten times the volume of recoverable reserves found in Australia to date. .

Jan 1, 1970

Natural gas is a comparatively new fuel in Australia. It was first used in small quantities in Queensland in 1965, but it was not until 1969 that natural gas reached the capital cities Brisbane, Melbourne, and Adelaide in that order; then in 1971 it reached Perth. By the mid seventies, natural gas had secured a significant proportion of the energy markets in Queensland, Victoria, South Australia and Western Australia and in 1976 supply commenced in Sydney. In that year - 1976 - gas supplied about 12.5% of the total demand for primary energy in Australia excluding transport. In the current financial year - 1981/82 - natural gas is expected to supply nearly 19% of the market and forecasts for 1990 range up to 25%. From a starting point in the late 1960's when manufactured gas supplied a small but important proportion of the non-transport energy market - less than 3% - we have exper- ienced an average growth of nearly 24% per annum up to the present time.

Jan 1, 1982

By Masters I. M, Ozberk E, Chalkley M. E

The integration of iron rejection as hematite with the Sherritt two-stage zinc pressure leach process has been investigated on the laboratory scale. The two-stage pressure leach process is applicable for a greenfield zinc plant, or for replacement of the conventional roast-leach circuit in an existing zinc plant. An excess of zinc concentrate is used to accomplish acid neutralisation in the first stage of pressure leaching, and the residual concentrate in the first stage residue is treated with an excess of acid solution in the second stage of pressure leaching to yield high zinc extraction. Integration of hematite precipitation with this process allows for the potential sale of the iron residue, greatly decreasing the residue disposal problem. Two flowsheets containing the desirable features of both of these processes are described in this paper, along with laboratory Results.

Jan 1, 1993