Search Documents

An Ore Reserves and Exploration System has been under continuous development at Mount Isa Mines Limited since 1970. The task of re-engineering the system has now begun, and the first stage is operational. This paper describes how the application of data base concepts, and table driving techniques has resulted in a design in which the input documents, validation procedures and file data content are redefinable by parameters, thus allowing the system to be tailored to suit varying geological Environments.

Jan 1, 1977

Economic mathematical methods have been developed and applied in the design, planning, development and managing stages in the mining industry. Economic and technological efficiency is achieved with the aid of a large range of probability models, which are used to enable decisions to be made progressively during the different stages. The entire operation is considered as a total system made up of sub- systems and the models representing these are consecutively interrelated with each other. Algorithms and programmes representing the economic mathematical models for all the stages involved were tested and were found to be applicable to the various important mines in the Donetsk basin. Currently, these models are accepted and widely used.

Jan 1, 1977

The reasons for including treatment of water in Whites and Intermediate open cuts in the overall rehabilitation strategy are given in the introduction. The target quality of the treated water also is discussed. Equipment selections are reviewed and reasons given as to why certain choices were made. The differences between this plant and an ore dressing mill are highlighted. An outline of the operating procedure is included along with a basic flowsheet. Cost estimates are briefly Discussed.

Jan 1, 1984

The economically significant seams in the Bowen Basin fall into four age groups, two in the Lower Permian and two in the Upper Permian. Coal deposition in the Galilee Basin did not commence until late in the Lower Per- mi-an and persisted into the Upper Permian. The Lower Permian and early Upper Permian coalfields of the Reids Dome Beds, the Collinsville Coal Measures and the Fair Hill-German Creek Formation are restricted to the west flank of the Bowen Basin. The uppermost Permian Rangal-Elphinstone-Baralaba Coal Measures have widespread distribution across the northern half and on both flanks of the Basin. Coal Measures in the subsidiary basins at BlairAtho/ and Ca/en were probably deposited at the same time as the Collinsville Coal Measures. The structure of the north west flank of the Bowen and the east flank of the Galilee Basin is essentially simple, but in the remainder of the basin doming and faulting complicate the structure. Also, bordering a large sec- tion of the east flank, is the Dawson Tectonic Zone, where the beds are tightly folded and faulting is intense. Cok- ing of seams is common in the northern sector of the Basin associated with igneous intrusion. With the exception of the Duaringa Basin on the east flank of the Bowen Basin, Tertiary sediments and basalt flows are more common at the western basin margin. Thick deposits of Tertiary sediments also occur in the south of the Galilee Basin. Con- sequently, coal subcrop, especially in the older, more westerly situated, coal measures is often at depths in excess of 100 m. East of this, the depth of weathering can be as shallow as 13 m and most of the coal subcrop is acces- sible to mining by open cut techniques. Coals deposited in the early Upper Permian are commonly more vitrain rich than those above and below. In the Bowen Basin, coal rank decreases from the north west to the south east, that is, from the semi-anthracites associated with the Dawson Tectonic Zone to the sub-bituminous coals of the southern Galilee Basin.

Jan 1, 1975

By Noble AC

Ore reserve reporting practices in the United States may be broken into four general categories as follows: ò Reserve reports, often of an unofficial and preliminary nature, which are made through the news media. These are often based on exploratory drilling or sampling results. ò Reserve reports made for the purpose of raising public funds by issuing securities on the stock market, or as part of other filings to the United States Securities and Exchange Commission. ò Reserve reports to obtain private funds from banks, financial institutions, or other investors. ò Reserve reports for internal use and planning by companies operating or evaluating mineral properties. This paper discusses current practices for each of these types of ore reserves reports and reviews recent changes which have affected those practices.

Jan 1, 1987

By P Cheluszka, M Jaszczuk, P Sobota

This paper refers to a new idea of stereometry of cutting drums of longwall shearers designed to get medium and hard to mine coals. A new way to place picks on a drum enables to readjust a number of picks being in contact with the body of coal to shearer haulage speed. Owing to this a remarkable increase in depth of a cut within the low range of haulage speed has been obtained. On comparing operating characteristics a considerable reduction in the specific energy consumption has been shown when using the units machined as per the new idea, in comparison with the units produced in series.

Jan 1, 2003

Mining and metals projects have tended to increase in both scope and cost to a point where many projects are Droperly designated as superprojects. Specialist engineer- constructors have developed organisations and systems to provide project management services during the design and construct phase of large projects. However, the engineer-constructor is also required to provide a wide spectrum of services during the evolution of large projects prior to the construction phase. Some common phases of pre-construction evolution are identified together with the associated types of specialised services which may be required. A project management team approach is described which has been developed for the design and construct phase. It is suggested that a modified matrix organisation could be adapted to the provision of special- ised services as well as to project management for ore-construction phases of the project.

Jan 1, 1980

Thermo Fisher Scientific is a supplier of samplers, instruments, analysers and consumables to the mining industry under the Thermo Scientific brand. The critical need to provide a representative sample to the analyser has played a pivotal role in product development. Products discussed are the Analysis and Sampling Station (AnStat) for mineral slurries, the Coal Quality Manager (CQM) and the prototype Bore Hole Analyser (BHX) with optional drill chip recovery system. Analytical techniques used in the above products are XRF, PGNAA and LIBS respectively. The company also designs and supplies conventional mechanical sampling equipment and complete sampling systems for bulk material applications (historical Ramsey brand). These products and application of them are presented.

Jan 1, 2008

The bureaucracy in Victoria has worked against exploration and mining development. There is no doubt that the new Mineral Resources development Act has simplified matters on the mining side of the system. However, WMC's Bendigo and Deep Lead experiences demonstrate that other parts of the bureaucracy can cause serious delays. The mining industry continues to view the approval process causal of excessive costs and delays compared with other States (and countries) and prohibitive to investment in Victoria.

Jan 1, 1992

Petroleum exploration is proceed ing in Western Australia at an ever- increasing pace. Results in recent years have been very successful, with the discovery and development of the Barrow Island oilfield and the Dongara gasfield, and the discovery of several major gas-condensate fields on the Northwest Shelf. The Northwest Shelf discoveries will have a big impact on the economy of the State by providing an abundant indigenous source of energy. Prospects for further large dis- coveries are believed to be excellent. The most prospective areas are thought to be on the continental shelf in the Carnarvon, Browse, Perth, Canning, and Bonaparte Gulf Basins.

Jan 1, 1973

By Forssberg KSE

Purification of GAsgruvan Limestone is carried out by anionic, cationic and cationic followed by anionic flotations in order to obtain a calcite concentrate that is acceptable to the paper industry. The results indicate that such a concentrate could be achieved by first carrying out the separation of siliceous gangue minerals by cationic flotation followed by the separation of carbonate during the anionic flotation. Stearylamine acetate (Flotigam SA) and a modified fatty acid (OMC 357) are found to be selective during cationic and anionic flotation, respectively. A final product containing 99.25 per cent calcite with a recovery of around 80 per cent is obtained. It is hoped that these results could be further improved by the follow-up process variable studies, in particular, the effect of reagent dosages and conditioning time at each stage of cationic and anionic flotation steps.

Jan 1, 1993

By Manlapig EV, Davis JJ

A methodology for modelling dense medium cyclones is presented for cyclones operating under conditions which avoid particle interference or apex crowding. Particle interference and apex crowding are shown to result in less efficient separations and represent undesirable regimes of dense medium cyclone operation. In order to avoid apex crowding, suitable medium to ore ratios and apex diameters should be used. Cyclone density differentials should be kept below approximately 400kg.m 3 to limit loss of efficiency due to excessive particle recirculation within the cyclone. The relationship between size-by-size partition curves shows that the flow split and density of the medium within a cyclone can be related to two new parameters, the pivot partition number and pivot density. The parameters are common to each partition curve in any set of size-by-size data and are mathematically related to the familiar performance characteristics, ecart probable (Ep) and separation density. The resulting expression confirms that the Ep and separation density are directly related.

Jan 1, 1986

By J Sarvinis

The design and operational aspects of fluidised solids transfer-cooling devices will be discussed in this presentation. The devices include air slides and fluoseals (also called seal pots, loop seals, etc), which are widely used in metallurgical plants and other processing plants. Cooling can be achieved while solids are transported in the solids transfer devices. The units combining solids transfer and cooling provide compact and clean plant layouts and also reduce capital and operational costs. Fluidised devices provide excellent gas-to-solids and gas/solids-to-surface heat transfer rates, hence high cooling efficiency. Fluidising gas, such as air, nitrogen or other gases, can be used as direct cooling mediums. Coolants such as water, steam and other liquid or gas cooling fluids can be used as indirect cooling mediums via tube coils immersed in the fluidised solids. The fluidised transport devices share some common features with fluidised bed equipment. The air slide is similar to a linear fluidised bed while the fluoseal is similar to a circular fluidised bed. Therefore fluidised bed design techniques are applicable to the design of the air slides and fluoseals. The heat and mass balance and temperature profiles of the devices concerned will be discussed in the presentation. The design criteria and operational philosophies of the critical components such as tuyeres and air spargers will also be discussed.

Jan 1, 2006

The Golden Cross is the first large precious metals mine to be both commissioned and closed in the æmodernÆ era in New Zealand. This paper discusses the life cycle of the Golden Cross mine, with emphasis on the closure process and post closure management.   The closure process has generally been very well managed, and successful, but in spite of that some on-going issues remain unresolved. Nearly nine years after the end of mining the mine owners are still actively managing the site, with no immediate end to that in sight.   The site has been described as atypical, due to the identification of a deep seated landslide below the tailings and waste rock storage facilities. However that should not be given too much emphasis when addressing the overall closure and post-closure management issues, which could well apply to other existing and future mine sites in New Zealand.   The Golden Cross can provide valuable lessons for other miners, and the issues arising at this site should be watched closely by the industry as a whole.

Jan 1, 2006

By Boyce WH

Earthquakes are the most frightening and devastating natural phenomena known to mankind. They strike without warning and their consequences can be disastrous in terms of the toll of human life, financial crises related to the damage or destruction of man-made structures and the social and economic effects on a wide spectrum of the affected communities in the aftermath of the event. Such situations can be widely attested to by most areas around the Pacific Rim. Indeed, the threat of earthquakes is always imminent because of the geological-tectonic nature of the region as manifested by past experiences. It is patently obvious that earthquake occurrences are not only a geological hazard but also pose a serious social danger. When one considers the 19 September 1985 Mexico (Michoacan) earthquake (Mitchell at al., 1986), the necessity of continuing research is of paramount importance. An estimation . of earthquake risk encompasses both qualitative and quantitative aspects and demands a multidisciplinary research effort integrating seismology, tectonics, geology, enginering, sociology, economics, insurance and governmental policies (Bolt, 1978; Booth, 1984). These roles in mitigating such a hazard have been aptly discussed by Press (1985). A series of discussion papers based on an intergovernmental conference covering the whole scenario were published by UNESCO (1978). A comprehensive case history was provided through a workshop on the 1886

Jan 1, 1987

The mechanism of caving is of interest to the mining engineer only in areas where he is directly concerned. One area is surface subsidence which is outside the scope of this paper. Another area is at the face where coal is being extracted and where control of caving is of vital importance. Coal mining systems have been developed with many considerations in mind, but in this list of considerations, strata control has seldom been given much importance. Research is in progress in Australia to endeavour to determine an optimum sequence for coal extraction underground. As information becomes avail- able from this work it is hoped that appropriate methods of controlling caving in various strata conditions will be devised. When this is done, equipment may be introduced to permit the mining operation to proceed under optimum conditions for strata control, rather than devising a mining procedure to suit the equipment available and methods developed for other reasons.

Jan 1, 1974

By Luck D

Current methods of mucking out small development tunnels are a major limitation to improved efficiency and high rates of advance. This is particularly true in the deep metalliferous mines of South Africa, where the harsh environment, remoteness of operations and the hard abrasive rock conditions mitigate against the use of the tunnel borer type of equipment. The Loader Distributor Train was designed to overcome the special problems of hard rock tunnelling. It combines advanced innovative technology with proven simple methods of operation and maintenance. The system aims at taking advantage of new, efficient and cost effective power sources in South African mines based on replacing compressed air with electro hydraulics and the new concept of hydropower. It also introduces electronics and computer technology, for both automatic control and fault finding, into the production environment. The system is designed to permit sophisticated equipment to be operated and maintained by a semi skilled labour force. Although still undergoing trials it is believed that the Loader Distributor Train will prove highly effective, and that the new concepts offer considerable potential in areas other than flat tunnels, in particular the cleaning of inclined shafts.

Jan 1, 1986

By E M. Rykaart

The design of soil covers as part of the remediation initiatives for mine waste facilities is common practice and more and more engineers are faced with designing these facilities. The design issues associated with these soil covers are complex and requires a good understanding of unsaturated flow. More engineers are making use of numerical models to predict how cover designs would perform, and this has been necessitated by the high non-linearity associated with solving unsaturated flow problems. There are numerous numerical models available to the prospective users and they are all simplifications of reality using different assumptions. The users of these models often do not understand the limitations of the models but rather select a model based on ease of use, and that lends to increasingly erroneous designs being proposed for construction. This paper describes a comparative evaluation of a cover design using four different codes available today; SoilCover, SWIM, HYDRUS-2D and HELP. The paper does not propose to measure these codes up against each other and make statements about which is better than the other but rather illustrates how the assumptions in each code affect the outcome. The data set used for the comparative study is a well calibrated data set that that has been collected over a long period in time and that has been collected according to strict controls. The authors present the pitfalls of numerical modelling of the surface flux boundary conditions, as well as present guidelines towards appropriate use of these modelling tools.

Jan 1, 2003

Results of blasting trials conducted at Gregory Mine, a large open cut coal mine situated in the Bowen Basin, show that fragmentation was improved or equalled whilst reducing the amount of explosives previously required. This was achieved by a system of deck loading whereby two or more explosive charges, separated by air gaps, were positioned in the blast hole, thereby extending the effective explosive column whilst minimizing the total explosives required. In the three trials to date, a saving of approximately 213 kg of ANFO per blast hole was achieved. This represented an approximate 20% reduc- tion in ANFO requirements.

Jan 1, 1989

By O K. Paki

A 14/12 millMAXTM pump was installed in the SAG1 grinding circuit as a trial replacement for the existing 12/10 Warman for performance comparison and in an attempt to overcome process difficulties. Krebs Engineers have developed the millMAXTM pump wet end to adapt to a variety of power frames. This system has been developed specifically for coarse material contained in mill discharge. SAG1 discharge screen undersize with a top size of 10 mm is collected in a flat bottom sump. Two 12/10 Warman pumps located on the same side of the sump, pump the screen undersize at 50 to 65 per cent solids to a distributor box which splits into two separate ball mill circuit sumps. One pump is installed towards the screen feed, while the other is towards the screen oversize discharge. The pump located towards the screen oversize discharge is prone to continual operating problems including pump bogging, high impeller and casing wear, and has consequently restricted SAG mill throughput. To rectify this pumping problem, it was decided to change-out the wet end of this pump with a millMAXTM. The design of the new pump enabled the wet end only to be retrofitted to the existing Warman pump frame, thus reducing change-over time. This was undertaken in the workshop under the supervision of a company representative where the pump, complete with bearing frame, new wet end, motor and base frame, was assembled. After installation of the millMAXTM pump during a SAG mill shutdown, performance indicators including motor power draw, sump level, and pump discharge pressure have been monitored. The trends indicate an increase in discharge pressure, low sump level, and low motor power draw. With the improved pumping efficiency there has been minimal pump bogging and no consequent SAG mill throughput restrictions. Pump wear rate has also decreased.

Jan 1, 2000