Search Documents

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

Evaluation of reserves on a production scale within a shear-hosted gold deposit is complicated by the nature of the mineralisation itself. The 'payable' ground seems to be confined to areas with intense shearing, while the remainder of the deposit is characterised by 'background' mineralisation at a very low level.

Jan 1, 1993

By Brant BA, Lewandowski R, Trendle M, Haughton D

There is a vast amount of geotechnical data, which can be obtained during exploration programs at new and existing mine sites. Additional information on the performance of the in-situ rock mass can be obtained from bore cores, which are usually only geologically logged and then stored. A computer based data management system for storage and retrieval of geotechnical data has been developed to access and manipulate such data.

Jan 1, 1983

By D Morris

This presentation discusses a water filtration technology termed Fabric Media that is somewhat novel to the Australian market place and reports several recent mining industry installations. Like many novel household cleaning products, the Fabric Media technology applies the science of active washable micro fibres as the means of capturing contaminant solid particles. The simple Fabric Media water filtration product offers several attractive attributes when compared to the more traditional media bed filtration processes such as sand filters, and barrier filters such as micro membranes. A micro fibre based filtration media enables both superior adsorption for the contaminant and wash ability. Stronger adsorption capture enables a much higher flux and greater solids loading density for the filtration task, meaning that lower cost and smaller footprint equipment is available. For Fabric Media water filters, a textile weave is selected that minimises the flow backpressure for a given particle size separation. Thus for an equivalent filtration performance this provides a much lower operating energy requirement, generally between 50 and 80 per cent less than for a sand filter. A Fabric Media is not abrasive to itself or to the filter tank. The filtration performance remains constant and predictable. The equipment life is much longer and the asset value of the new filtration equipment should maintain throughout the project life. Fibres are extremely mechanically robust and chemically inert. Fabric Media survives repetitive exposure to a rapid mechanical washing event providing high wash efficiency with minimum equipment off-line time for the backwash. Dislodging captured contaminants by a high-speed mechanical agitation enables a minimum off-line time during backwash events. The vigorous backwash destroys adhering flocculant and eliminates the formation of mud balls, which can permanently foul sand filters. The mechanical agitation wash of the Fabric Media water filter ensures complete removal of grease and biofilm, which can adhere and block a membrane surface. In comparison to sand filters and micro filtration membranes, the Fabric Media product is applicable to a significantly wider range of solids concentrations without permanent damage. The technology is very forgiving to excursion in plant control and is therefore considered a very operator-friendly concept.

Jan 1, 2006

By Van Rooyen F

An introductory review of the current grade control blasting techniques (selective mining strategies) used in the Eastern Goldfields has recently been undertaken. The survey was initiated and conducted by the Western Australian School of Mines. Four distinct selective mining strategies have been identified and a number of trends have been highlighted. Many operations, however, have developed techniques which use a hybrid method to suit the site conditions. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and experiences no mixing of the various identified ore and waste blocks and is fully reco- vered at the minimum overall operating cost. Due to this unified aim all of the grade control blasting techniques have many common design Features.

Jan 1, 1988

Modelling of Magnetic Carrier Separation Process Using Computational Fluid Dynamics

Sep 13, 2010

The reasons for selecting two stage pebble milling in preference to conventional methods of grinding are discussed. Commissioning of the first section was completed in October, 1969. Improvements in both the operating and engineering aspects were then incorporated in the section commiss ioned in March, 1971.

Jan 1, 1975

By Teniswood CF, Sheppard I, Mason LG

An industry initiated project, sponsored by the National Energy Research Development and Demonstration Council, has worked for two years in developing design guidelines for underground coal mining machinery.Continuous miners and shuttle cars were selected for the initial development of design guidelines as these machines were linked with 7500 lost workdays and 490 reported injuries during the preceding two years.

Jan 1, 1991

By G Muller, P Larrondo, M C. Godoy

The categories of Mineral Resources and Ore Reserves that may be used for public reporting in Australasia are defined in the current JORC Code (2004). Most internationally accepted codes emphasise the principles of transparency, materiality and competence in classifying resources. They also provide some guidance in considering the impact of data quality. There is no method recommended in the JORC Code to classify a Mineral Resource into the allowed categories of Measured, Indicated and Inferred for public reporting. A clearly defined procedure is desirable for many reasons, including consistency, repeatability and auditability. The demonstrated use of geological knowledge in the classification method is desirable. In deposits with abundant historical data there can be large variations in data type and quality. Quantification of the error of the estimates may also be considered. Ways to formally incorporate such information into the resource classification process are presented as a first step towards establishing an objective, repeatable methodology that allocates resources into appropriate categories based on defined criteria of accuracy and precision.

Jan 1, 2006

By Jiricek F

Legislative change has reformed the licensing process in Victoria. The Mineral Resources Development Act 1990 and the two stage system of licensing with the authority to commence work is discussed. A key part is the requirements of planning consent, being either an Environmental Effects Statement or the issue of a Planning Permit prior to the issue of an authority to commence work for mineral extraction. Examples of recent experience is discussed.

Jan 1, 1997

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

The developments in hydrocyclone classification in the milling circuit at Bougainville Copper Limited are discussed. A major change in cyclone size and improve- ments in operating conditions have been made. Test work has been carried out to assess the classification performance of a modified Linatex cyclone, Wemco cyclones and a two stage cycloning circuit. The use of a scalping cyclone, to remove coarse material from the present overflow product for regrind, has also been investigated.

Jan 1, 1978

By J F. C L Costa, J C. Koppe

The goal of this study is to characterise co-processed clinkers by identifying the most common minor elements, their distribution in the clinkers and possible effects on the mineralogical properties of the same. The results show the presence of an elevated content of transition metals, especially manganese concentrated in the matrix (up to three per cent) of the clinkers. Anomalous concentrations of arsenic have also been detected, especially at silicate crystal edges. The results indicate that the tracer elements can perfectly be associated to the mineralogical characteristics of the clinkers.

Jan 1, 2008

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

Geological models for the exploration and evaluation of epithermal Au and porphyry Cu-Au deposits rely upon a classification of different deposit styles and an understanding of the evolutionary processes of deposit formation. These models guide the interpretation of subsurface deposit anatomy in order to target drill testing and assist the explorationist to focus on the more prospective projects. It is important for the explorationist to distinguish between different styles of magmatic arc Au deposits as each style displays distinctive characteristics with exploration implications. Magmatic arc Au deposits are distinguished as porphyry Cu-Au formed at depths of 1 - 2 km at the apophysis to larger, buried, magmatic sources which are also the ultimate metal sources for the varying styles of shallower level epithermal Au deposits. Low sulfidation epithermal Au deposits characteristically develop from dilute circulating meteoric waters and are distinguished as the group with a closer relationship to intrusive source rocks, and slightly higher sulfide contents (still generally

Jan 1, 2004

The purposes of defining the mining environment for underground mass mining and the uses of characterisation data are outlined. The requirements for data in the areas of geology, surface and groundwater hydrology, topography and environmental constraints and geotechnical studies are identified. Emphasis is then placed on the collection and interpretation of geotechnical data for establishing the in situ stress regime and for rock mass characterisation. Methods used for diamond drilling, core logging, borehole logging, data analysis and presentation, rock mass modelling and rock mass classification are outlined. Finally, recent and potential advances in the state-of-the-art are identified in areas such as geophysical methods, measurement while drilling, computerised data collection and analysis, rock mass modelling, in situ stress measurement data presentation and interpretation, and some applications of rock mass characterisation data.

Jan 1, 2000

By C McInnes

The key to successful flotation plant design, production planning and mine/mill optimisation is a solid understanding of the resource to be processed. As advocated by the authors of this paper, the main components of geometallurgical modelling of an orebody and its associated flotation plant are: an ore sampling program and subsequent laboratory testing of these samples in order to extract process model parameters; geostatistical distribution throughout the resource model of the process parameters; calibration of the plant via benchmarking (for existing operations); and plant simulation using a system of process models and the distributed metallurgical parameters (from step two) as the data set.It is important that the grinding and flotation models are linked. For example, a laboratory test conducted on a drill core sample, intended to represent a portion of the orebody, is conducted at a specific grind (represented by a P80). However, when that ore is actually processed through the plant it may well be (and in many cases most likely will be) at another P80. Additionally, the flotation plant residence time will often be determined solely by the grinding circuit capacity and feed slurry density. In the case of SAG mill û ball mill circuits, the fluctuations in tonnage and grind are known to be high. The modelling approach described in this paper allows for changes in the measured flotation kinetic parameters in order to reflect the expected grind as determined by the comminution process.

Jan 1, 2005

By R J. Nicholson, J M. F Clout

As part of an overall strategy to make significant new technological advances for the sustainability of the mineral processing and related process industries CSIRO Minerals has developed a new dry separation device. It represents a technology breakthrough and has the potential to radically change the way in which dry particle size classification is achieved in the minerals industry. Conventional dry separation techniques have limited applications and often suffer from low productivity, high operating costs, low separation efficiency, the need for dust control and a lack of flexibility. In the absence of efficient dry techniques, wet processing is often used. The use of wet processing either requires the introduction of water into a separation process, which causes environmental concerns through the need for water supply and tailings dams or the use of æunfriendlyÆ chemicals for dense media separations that have considerable impact on handling and disposal. Wet processing also increases operating costs due to plant instability, materials handling, thickening, filtration and product drying. The new CSIRO technology exploits a combination of natural and applied forces to achieve specific particle motions that produce size separation. In doing so, many of the traditional shortcomings of dry separation have been overcome. The CSIRO Dry Particle Size Separator is ideally suited for dry size separation applications within the size range 1 mm to 30 ¦mfor moderate moisture levels (2 per cent), have low unit throughput, produce a fixed cut size and are therefore impractical where very high unit capacity and low operating costs are required. This paper presents a review of dry separation devices together with details of the new Dry Particle Size Separator and typical results for a number of materials, including iron ore and quarry dust.

Jan 1, 2002

The treatment of slimes has of late years been the chief difficulty in connection with cyanide work, in which much time and money has been spent in endeavouring to find a practical solution of this problem.The processes at present in use are:-1. Filter pressing, as practised in Western Australia.2. Decantation, as practised in South Africa.Filter pressing after apitation affords a ready and efficient means of separating the gold bearing solution from the slimes and admits a perfect washing thus ensuring a high extraction but the very high working costs forbids its application except on high grade material, the chief items being the necessary large amount of labour, compressed air, and general upkeep, none of which can be materially reduced. The decantation method has the ad vantage of low working cost but on the other hand the low extraction obtained, due to imperfect washing, the length of time occupied in' the treatment, and the enormous bulk of solutions to be handled, are serious disadvantages.In either process it is absolutely necessary to obtain a perfectly clean solution before starting the gold precipitation by zinc, which is a source of much trouble. Also the high first cost of installing either plant is such that they can only be adopted on mines with very large working capital.

Jan 1, 1903

King Island is situated at the western approach of Bass Strait and approximately mid way between Victoria and Tasmania. The scheelite orebodies lie within the south east of the island. Ore bearing horizons from 10 m to 40 m thick occur in south and east dipping stratiform deposits. The orebodies occur in skarn formed by contact metasomatic replacement of carbonate rocks by granite intrusives. The scheelite is deposited as fine disseminated grains in and along the margins of andradite garnets in the skarn. King Island Scheelite operates two under- ground mines from which 350 000 tonnes per year are obtained. The Dolphin mine produces almost two-thirds of the total. See Figure 1. The Dolphin orebody lies beneath the sea and an area of reclamation. The orebody is inter- sected by zones of major dislocation. A chequerboard post pillar cut and fill stoping system has been chosen to provide the necessary support to the hanging wall. Because the stability of the pillars is critical to the economic welfare of the mine, considerable attention is given to the reduction of overbreak.

Jan 1, 1977