Search Documents

By McManus D

Situations where in-pit bench stripping methods are favourable are introduced. Examples from Peak Downs Mine are used as a guide to the range of methods available.A number of geological and geotechnical conditions adverse to successful in-pit bench stripping are described. In all cases bench, floor, and/or final lowwall instability can develop and compromise the economics of extraction.

Jan 1, 1992

By Dierling D. H

The paper briefly describes the mining system employed on Western Deep Levels for the past 20 years. The negative aspects which gave rise to a new mechanized method of mining are discussed. The sequence of events leading from the Mine's first attempt at trackless mining in 1980 to the present day in-stope project is presented. The original justification for this project and the in-stope trackless mining method is described in detail. The results to date are evaluated and the original rationale for going in-stope trackless mining questioned. A totally new mining philosophy for Western Deep Levels, whereby major geological disturbances are left in situ and longwalls re-established and mined using trackless mining machinery is described. The economics of this mining method are discussed. Trackless mining machinery can also be put to good use within the conventional longwalls in a new method of mining using Load Haul Dumpers (LHD) in reef drives. When the instope trackless mining project commenced in 1983, it was stated that expansion to any significant degree with diesel powered vehicles could be ruled out and electrically driven alternatives would have to be developed. This issue is discussed and the Mine's decision to expand with diesel powered vehicles explained. Finally, the extent to which trackless mining is likely to be seen in the 1990 s at Western Deep Levels is discussed.

Jan 1, 1986

By M Binks

This paper presents a case study that describes the selection, development, engineering and construction of a process plant for the biological oxidative pre-treatment of a refractory pyrite-arsenopyrite gold ore flotation concentrate. Prefeasibility and feasibility study resource modeling, metallurgical testwork, and environmental and engineering studies are outlined. Options considered for oxidation of the ore, which examine cost, risk, operability, recovery, engineering and environmental aspects are compared, with particular reference to pressure and biological oxidation. The BIOX« biological oxidation process was selected as the preferred oxidation process and the flow sheet for this process is presented. Selection of the BOIX« process resulted in special requirements for the feed preparation circuit, residue treatment and disposal, materials of construction and engineering. Use of a biological process in ore treatment also introduces particular process and engineering risks the management of which are discussed.

Jan 1, 2004

By Little T. N, Bettess D

For many mining operations the challenge of equalling World Best Practices has become the key motivator for increasing mine productivities and for lowering total costs. In most instances this will only be achieved if mines optimise their total system rather than minimising specific costs within unit operations. In the past, drilling and blasting have been viewed as a cost to be minimised rather than operations which should have their impacts fully leveraged. Once a hardrock orebody is defined the activity which has the most substantial impact in determining the efficiency of a mining operation is the blasting. The output from a blast affects every downstream operation; only by understanding the extent and interactions can the mine be optimised. Substantial improvements to hardrock mining, quarrying and excavation operations are achievable. Instead of seeking the regular one to three per cent improvements based on reduction of consumables, mine operators would be well advised to go for much bigger targets of ten to 30 per cent by fully leveraging the drill and blast operations.

Jan 1, 1995

This paper discusses why Argyle Diamonds adopted thickened tailings disposal in 1985 and how the system was developed over the next seven years. A wide ranging review of the thickened tailings disposal system and the tailings deposit it was producing was carried out during 1992 and 1993. The results of that review led to the abandonment of thickened tailings disposal at Argyle because of serious concerns about the stability of the resultant tailings deposit. The exposure to the risk of liquefaction and an assessment of the consequences if this happened to the thickened tailings deposit are shown. The criteria for selecting the new tailings disposal strategy are then described. The final section of the paper discusses the management strategies that have been put in place. These are designed to: ò reduce the risk posed by the thickened tailings deposit to an acceptable level; ò safely store tailings to the end of mine life; ò produce a land form that can be decommissioned to the satisfaction of Government regulatory bodies.

Jan 1, 1996

By Chappel R. A, Fishburn B. R

The Eastern Distributor Tunnels - the first major road tunnel project in Australia - are the preferred solution to traffic congestion problems, when compared with alternatives, in this inner urban environment. This is because of the reduced impact on residential housing, the improvement of the existing environment, less restrictions on future developments, and a reduction in noise and pollution. Developments leading to a tunnelled solution, traffic needs and reasons for route location are discussed. Criteria for design of tunnel alignments and geometry are described, including the restraints imposed by surface connections on profiles and grades resulting in low rock cover at tunnel portals. The main geotechnical restraints are a major weathered dyke at the shallow large span underground fork and the weathered Ashfield Shale capping the Hawkesbury Sandstone at a portal. Rock cuttability and excavation methods are discussed. Roadheader machines are the most suitable for the varying shallow arched cross sections required and the tunnel lengths involved but the use of blasting in special situations cannot be ruled out. Initial support for the major tunnel lengths will be provided by rock reinforcement in conjunction with shotcrete. Steel ribs are proposed in areas of low cover and weak ground. Final support will comprise an insitu concrete lining. Construction concepts and special tunnelling methods required at the shallow underground forks and tunnels are described.

Jan 1, 1987

By Scherbatsky VB, zon BM, Babushkin NM, Kitaev BI, Shabel&apos

The structure and hydrodynamics of the raceway zone of a blast furnace was studied on a cold model representing a sector containing two tuyeres. The model differed from the usual in that it was prov- ided with continuous flow of the coke layer at pre- determined rates, had provision for changing the tuyere parameters (diameter, protrusion, inclinat- ion) and irrigation of the layer with liquid. A combination probe was developed which per- mitted simultaneous measurement of the pressure field both across the area and through the height of the layer as well as determining the topography of the raceway. The velocity fields in the layer were measured with a specially made impulse thermo- anemometer. The determining criteria of the model were taken as the relationships between the energy of the blast and the particles, the dimensions of the raceway and the cross-section of the tuyere. The model established the effects of the tuy- ere structural parameters, blast parameters and amount of liquid products of smelting on the con- figuration of the raceway, the structure of the layer, pressure and velocity fields in the vicinity of the tuyeres and in the vertical direction through the layer. The properties of the raceway formation and the structure of the layer in motion have been clarified.

Jan 1, 1981

By Hall T. P, Taylor R. N

Fluid flow in a 1:14 scale water model of the shaft and settler of the Kalgoorlie Nickel flash smelter has been investigated by flow visualisation and numerical modelling. Detailed flow fields through the reaction shaft, settling chamber and uptake are presented for flow rates up to 800 Vm and a number of burner configurations. The predicted flow fields were compared with experimental data obtained from streak photographs and video recordings. The effects of cessation of flow through individual burners and changes in shaft dimensions were also Investigated.

Jan 1, 1992

Traditionally, surface coal mines in the Western United States have been limited by economics to depths between 150 to 200 feet. Utah International Inc., however, is now planning to strip coal its San Juan Mine in Northwestern New Mexico to depths ranging up to 400 feet while uncovering 20 feet of steam coal. This method is cost-competitive with nearby shallower coal deposits and underground mining of the same property. How trucks and shovels can pre-strip for a dragline, along with results of the planning process, comparison with alternate systems, capital requirements, operating costs and comparisons with other coal sources are all detailed. Also discussed are the major problems anticipated, how they might be corrected, and potential improvements to the concept. Introduction The San Juan Deep Stripping Project will be situated at Utah International's San Jean Mine. The mine is in the Four Corners region, so-called because four states enjoy a common border point about 30 miles to the northwest.(see Figure 1). The area is a semi-arid plateau region with an average elevation of 5,200 feet, receiving an average of 6 inches of precipitation annually

Jan 1, 1981

By Shuguang L, Jing S

Computer controlled truck dispatching systems is a newly-developed technical system in surface mines with shovel-truck technology. The real time dispatching criteria, as the core of optimal truck dispatching software, are analysed and a new criterion, complex dispatching criterion, is put forward. Dispatching criteria previously proposed include: 1. `Earliest Loading' (EL) - to assign a truck to the shovel at which the truck can be loaded earliest. 2. `Max Truck' (MT) - to assign a truck to the shovel at which the truck will have the shortest waiting time. 3. `Max Shovel' (MS) - to assign a truck to the shovel which has been waiting for the longest time. 4. `Minimum Saturation Degree' (MSD) - to assign a truck to the shovel at the branch where the truck flow saturation degree is minimum. 5. `Minimum Saturation Degree with Truck Cycle time consideration' (MSDTC) - as the MSD principle, with the truck travel cycle also considered. 6. `Fixed Dispatching' (FIX) - to assign trucks to fixed shovels. A system simulation model has been set up for truck dispatching system analysis. A few surface coal mines have been selected for case studies. Equipment waiting times and shift production of the system are obtained as the main outputs of the model. Simulation results show that each dispatching criterion has its own applicable range, no one can absolutely dominate the others. For example, when under-trucked, EL and MT criterion can obtain higher production than the MS criterion; when over-trucked, it is vice versa; while for MSD criteria, better results can be obtained no matter how the truck numbers fluctuate. From the view point of shovel output balance, large fluctuations occur for EL and MT criteria, while a good balance can be obtained for other criteria. In the light of dynamic change of mining system conditions, a single dispatching criterion is not necessarily reasonable. A complex dispatching criterion has been put forward to seek the complex optimum effect. Taking the advantage of each dispatching criteria, the dispatching result of a complex dispatching criterion dominates over individual dispatching criterion and a comprehensive optimum effect can be reached.

Jan 1, 1995

By Vogwill R. I J

The Boddington Gold Mine, operated by Worsley Alumina Pty Ltd, is located about 100 km south of Perth and is one of the largest-producing gold mines in Australia.Multiple open pits are planned and several extend below the water table, through the deeply weathered lateritic profile and into the underlying Archean bedrock. Groundwater related mining problems, such as poor trafficability, wet floor conditions and slope instability began to occur early in 1990.The mine is located within Archean greenstones which are steeply dipping and faulted. Rock types include mafic to felsic volcanics, pyroclastics and sediments. These rocks have been regionally deformed and metamorphosed and are intruded by quartz micro-diorites and post-mineralisation dolerite dykes. Deep weathering has produced a typical oxide profile consisting of laterite, clay and saprolite zones underlain by weathered to fresh bedrock.

Jan 1, 1993

By G Power

The successful implementation of sublevel caving (SLC) at Ridgeway Gold Mine (Ridgeway) requires the technical aspects of caving and flow behaviour to be understood. Cave propagation must be controlled and continuous to allow safe extraction of ore below. The understanding and use of processes to manage granular flow behaviour are also required to ensure economic metal resource recovery. Caving and flow technologies are thus critical to the economic viability of the application of the SLC mining technique to Ridgeway Gold Mine. At the time the Ridgeway SLC design was approved there were significant technical uncertainties associated with cave mining methods, including the SLC mining method in competent rock masses. This was in spite of the fact that caving is a relatively low cost mining method. Unique features generating technical risks at Ridgeway include: the fact that the orebody is blind (550 m below surface); highly competent cap rock (RMR >50); and high aspect ratio (height to width ratio of 3:1). Due to the presence of these unique features Ridgeway is considered to be beyond the current state-of-the-art in SLC mining technologies. The success of the technique at Ridgeway to date has indicated that blind SLC mines in strong rock mass can be operated safely and productively, if the technical risks are understood and properly managed. The risk management process was defined by the use of a formalise process to identify and assess the risks to the mine. The major mining related risks were formalised into Major Hazard Management Plans (MHMP) which contained a description of the risk, early triggers indicating the creation of a hazard and a series of agreed responses to be automatically initiated in the event of each trigger occurring. This paper outlines the following with respect to the critical technology areas of caving and flow: international industry, state-of-the-art technology; gaps in the application of this technology; the application of risk management, new processes developed at Ridgeway to bridge these gaps, including issues encountered; and trials and experimentation conducted to develop the new processes.

Jan 1, 2003

By E S. Souza, H Delboni Jr, M F. Calixto

This paper aims at presenting the results of laboratory, pilot plant and simulation studies for the design of the grinding circuit for the beneficiation of compact itabirites from the Conceitpo mine. Two alternatives were investigated, both utilising the current crushing circuit up to tertiary crushing. Under alternative #1, quaternary crushing was considered to produce the feed of the ball mill; under alternative #2, high pressure grinding rolls were selected to prepare the ball mill circuit feed. Pilot scale studies pointed towards the use of high pressure grinding rolls (HPGR). The circuit design was based on a throughput of 720 t/h, representing a nominal solids flow rate of 600 t/h, considering a design factor of 1.2, and P80 of 95 ¦m.

Jan 1, 2007

The Beverley uranium mine û now in production in the remote north of South Australia at1000 tonnes per annum û was established to meet a projected, but little-recognised shortfallin primary supply of uranium for the nuclear industry in the early part of the 21 st century. Inthe context of AustraliaÆs lack of bi-partisan support for uranium mining and the nuclearindustry, a four to five year window of opportunity existed from 1996 to establish the mine.During this period, Beverley achieved a number of firsts including: the first ISL mine inAustralia; the largest ISL mine in the world and the first to produce more than 500 tonnes ofuranium in its first year; the first to be established under a new Native Title regime in SouthAustralia; and the first to be established under a revised South Australian Mining Act.Beverley was brought into production against the background of: hostile opposition fromanti-nuclear activists; a suspicious and at-times hostile media; a regulatory and politicalcommunity that was unfamiliar with ISL mining; commercially unsophisticated Aboriginalgroups; an inexperienced engineering industry; and the vagaries of development in a remote,semi-arid location with neither population nor infrastructure. The lessons that can be learnedfrom Beverley showed that û like much in life û flexibility and timing are crucial.

Jan 1, 2002

By Lawson F

The Australasian Institute of Mining and Metallurgy is a society of engineers and scientists formed in 1893 (incorporated by Royal Charter in 1955) to advance science and engineering in the mineral industries, and to facilitate the exchange of information and ideas to enhance the professional excellence of its members. The Institute has several grades of members. The professional members are linked with Student and Company Members, as well as an Affiliate grade covering other professionals and non-professionals with experience in the mineral industry. The diverse group covers all sections of the mineral industry, from exploration through production to marketing of minerals and petroleum. Corporate (professional) membership also covers science and engineering professionals from specialisms other than the "traditional" ones in geosciences, mining and petroleum engineering and metallurgy. The Institute has Branches throughout Australia, New Zealand, Papua New Guinea and Oceania, whose activities complement the corporate occasions arranged for the benefit of all members by Headquarters in Melbourne. Members are drawn from all sections of the industry - private enterprise, government, research, education, and the support sector, including consultancies, manufacturers and suppliers. Membership of The Institute allows professionals to contribute to their profession through participation in The Institute's seminars and conferences, its many committees and Branch meetings, and through contribution to its many high standard publications. The Institute is the main body for the accreditation of professionals in the minerals industry. The activities of The Institute are directed towards the achievement of professional excellence. It provides opportunitites for contact with, and professional support from, colleagues, and the interchange of information on the latest industry developments.

Jan 1, 1989

In comparisons of a trial extruded brick containing 33 per cent coalwash and 67 per cent clay and a trial pressed brick containing 100 per cent coalwash with a standard extruded clay face brick, the mixed feed stock trial brick compared favourably with the standard brick. If a highly plastic clay is used to mix with the coalwash, satisfactory results are obtained in respect to dimension, strength, water absorption, efflorescence, resistance to salt attack, hardness, colour, weathering, mineralogy and porosity. Although a brick containing only coalwash can be successfully manufactured in a press, its mechanical and physical properties are inferior. This mixed feed stock brickmaking technology leads to the utilisation of a by-product with a potential saving of raw material costs. The extent of use is likely to depend on the proximity of the coal washery and the brickworks and the economicsof transportation costs.

Jan 1, 1992

By E S. B Santiago, C P. N Moreto, L V. S Monteiro, G H. C Melo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Iron oxide-copper-gold (IOCG) systems of the Carajás mineral province (Amazon craton, Brazil) are structurally controlled by regional-scale shear zones and have formed by multiple episodes of fluid circulation and hydrothermal alteration in the Neoarchean (2.71–2.68 Ga and 2.56 Ga) and Palaeoproterozoic (1.90–1.87 Ga).Collectively, fluid inclusion, boron, oxygen and hydrogen isotope data and Cl/Br–Na/Cl ratios in fluid inclusions reveal that regional circulation of non-magmatic brines (eg evaporative fluids/evolved sea water) and mixing with other fluid sources (eg meteoric or magmatic) is an important attribute in the genesis of the Carajás IOCG systems. The ?33S and d34S compositions of sulfides from the Neoarchean and Palaeoproterozoic IOCG systems suggest that the ore-bearing fluids have assimilated sulfur from crustal reservoirs. Nevertheless, most ?33S measurements have indicated mass independent fractionation (MIF) effect for both systems which points to the possible involvement of surface sulfur sources.CITATION:Xavier, R P, Monteiro, L V S, Moreto, C P N, Melo, G H C and Santiago, E S B, 2015. Non-magmatic versus magmatic fluids in the genesis of Archean and Palaeoproterozoic iron oxide-copper-gold systems of the Carajás Mineral Province (Brazil), in Proceedings PACRIM 2015 Congress, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Bevilacqua P, Preti U

The basic separation phenomena taking place in film concentration processes are studied through a kinetic-probabilistic approach. This approach is based on the fact that the particle velocity in the film separation phenomena is a random variable and may be defined by frequency distributions and probability laws. The approach requires: 1. development of probabilistic models for describing the behaviour of particles having different specific gravity and size along selected trajectories in the separating devices; 2. setting up an experimental procedure for determining the relevant frequency distribution curves at the exit of the separators for the particles mentioned above; 3. estimation of model parameters and model validation. In the paper, the model equations are given for the mass distribution of particles on the surface of separators, the mass distribution at the exits of shaking tables and the residence time distribution in channel type devices. The relation between residence time distribution and particle velocity distribution is derived. The test procedure has been defined and results are reported for the exit or residence time distribution in channels. A comparison between experimental and calculated frequency distributions is reported.

Jan 1, 1993

The accurate calculation of ore reserves is one of the most important functions under- taken at a potential or operating mine. In recent years there has been a trend towards recommending more and more complex techniques for the calculation of reserves. However these are not always necessary and many improvements could be made by the use of all potential data and a heavier geological input. An ore reserve should be the result of geological not mathe- matical or engineering reasoning. All ore reserve estimates are wrong and the important thing is to.recognise why they-are wrong and to take action to minimize the errors. Geostatistics and other complex mathematical techniques may appear to answer all our needs for ore reserve accuracy but there are many drawbacks, not least of which is the communi- cation gap which may develop between the operator and both management and production Personnel.

Jan 1, 1979

By K Matsui, R N. Gupta, H Shimada

Roof falls and failures of powered supports were major threats at longwall face. Abnormal geological conditions were caused roof falls and shield damage. Therefore continuous monitoring and analysis of strata behaviour was imperative on real time for forecasting adverse behaviour. Novel PXI instrumentation system was successfully developed for continuous monitoring and analysis of supports pressure, leg closure and gate roads convergence. However, this paper briefly examines the novel gate roads convergence monitoring system with field applications.

Jan 1, 2003