Search Documents

Upper Cretaceous and Eocene coal measures of the Ohai Coalfield are stratigraphically complex, and coal seam geometry and quality are influenced by washouts and partings resulting from accumulation in a fluvially active environment. Mining efficiency is influenced by these seam discontinuities, which are difficult to predict in the absence of refined paleoenvironmental models of peat accumulation. Petrographic variations between the Upper Cretaceous and Eocene coals indicate differences in the environments of peat accumulation. Seams in the Upper Cretaceous Morley Coal Measures accumulated autochthonously (in situ) in predominantly forest swamps with a high water table. These swamps were occasionally subject to brief floods. No significant changes in swamp vegetation, as indicated by petrography, have been detected between seams. In contrast, the greater content of mineral matter and maceral detritus within the Eocene Beaumont Coal Measure seams indicates hypautochthonous (locally transported) peat accumulation under more frequently flooded conditions. A precursor forest-moor is again indicated but the greater resin content of these coals compared with the Upper Cretaceous examples may suggest a greater contribution from conifers. Integration of coal petrography with investigation of other seam characteristics and coal measure sedimentology is expected to result in a detailed understanding of original depositional controls on peat accumulation. Paleoenvironmental models derived in this way should facilitate prediction of seam geometry, roof and floor conditions, and variations in coal quality, with obvious benefits to exploration and mine development.

Jan 1, 1983

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

Alcoa of Australia's Western Australian bauxite mining operations in the Darling Ranges, south east of Perth, present major challenges in the control of air blast. The close proximity of rural communities and the face profile make the traditional methods of air blast control difficult. An extensive blast noise monitoring programme has been established. The develop- ment of a computerised blast noise prediction model and the establishment of a radiosonde weather balloon facility have reduced blast induced complaints by a factor of ten. The meteorological factors affecting blast noise transmission are discussed and examples are given of adverse weather condit- ions for the south west region of Western Australia.

Jan 1, 1982

The paper describes a computer model developed within the State Electricity Commis- sion of Victoria for use in open cut planning. The purpose of the model is to simulate all the typical occurrences in, and influences on, the coal supply and overburden disposal systems in order to be able to assess their performance. The model incorporates much of the long term and day-to-day operations planning logic required for the allocation of resources within an open cut. This logic takes account of power station demands, bunker stocks, plant and crew availability, the balance of reserves between dredgers, planned maintenance, etc. The perfor- mance of plant within the system is simulated using random selections from statistical distri- butions of Time to Failure and Time of Failure for each plant item. The application of the model in selecting a suitable bunker capacity in a notional open cut development is described to illustrate the potential of the model in optimising plant selection.

Jan 1, 1982

By W R. Hancock

Control of complex machinery through the internet is investigated through the construction of a vehicle prototype developed using off-the- shelf hardware. The vehicle was able to be controlled remotely through the use of a client side interface connected to a steering wheel and foot pedals. By attaching sensors to the vehicle, data could be collected from which one could infer the effectiveness of such a control system. The effect of latency on control was monitored by the introduction of an artificial latency, simulating a wide variety of internet-related issues, such as unstable connections and dropouts. Sensor data could then be used to gain an understanding of how the system could be improved though either control or interface design. A path tracking experiment was conducted to gather controllability data and it was found that such a system is plausible within a reasonable range of latencies. It is expected an area of future research would be an extension of this current project, applying the information gained to real world control systems.

Jan 1, 2008

By Jackson S

An investigation into different aspects of importance in the understanding of explosibility of hybrid mixtures of coal dust, air and gases potentially found within mine workings through a comprehensive laboratory program of explosibility tests was conducted. Plotting of test results revealed that conditions of potential explosibility could be described using two dimensional flammability limit surfaces- for coal dust/oxygen; methane/oxygen; and coal dust/methane mixtures. From these plots, the three dimensional flammability envelopes defining the explosibility of the coal dust/methane/oxygen mixtures can be defined and illustrated for a coal sample. The surfaces of the three dimensional envelope describe limits which separate inert mixtures of coal dust and methane at varying oxygen levels from those concentrations which are ignitable under defined conditions. It is considered appropriate to generalise that the geometric shapes of these limit regions are applicable to all type classifications of coal dust. There are practical applications of these results to the underground environment.The action of free radical initiators in the propagation of a methane gas explosion was examined for its applicability to the flammability of coal dust/gas/air mixtures. The oxides of nitrogen or NO x radicals have influence upon the lean limits of flammability of hybrid mixtures and this is illustrated by use of three dimensional coordinate geometry. Gases can be introduced to the underground environment through the exhaust gases of diesel equipment. It is concluded that radical species can substantially increase the flammability of gas and dust flames and as a consequence raise risk of mine atmosphere explosibility.

Jan 1, 1998

Norway, a country large in area but small in population, has put large effort in protect- ion of its inhabitants in case of war. The Civil Defence has provided shelters for more than 50% of the population. Some of these shelters are put into rock. Since rock installations give large resis- tance against weapon effects and also by advan- tage can be used for several purposes in peace- time, an interesting development has taken place the last decades. In towns and cities you will find sport halls, swimming pools, bowling and shooting ranges etc in rock, which easely can be conver- ted to civil defence shelters. Some typical installations are highlighted in the following.

Jan 1, 1987

By P McGavin, R von Varendorff

With the economic trend towards reduced capital spend, more stakeholders are focusing on improved operational efficiency and productivity. Advancements in achieving the optimum dollar-per-tonnage will be more dependent on creating a logistics system that is well balanced and economically optimised. Critical to predicting a successful business case is the ability to accurately define capacity, realistically increase throughput and proactively translate objectives into design and operating requirements. Failure to do this will create an unrealistic perception of capacity and performance for the export corridor. This transition requires a fundamental understanding of the drivers that impact capacity, cost and value across the entire logistics chain. Through examples, this paper will identify the contextual requirements for simulation models that assist decision-makers and stakeholders to more clearly understand the implications of decisions that will define capacity and operational performance. The aim of this approach is to provide a rigorous analysis of the outcomes - regardless of whether the export corridor is owned, used and operated by one entity or various companies.CITATION:von Varendorff, R and McGavin, P, 2013. Can we live up to the capacity expectations weÆre predicting for our iron ore export corridors?, in Proceedings Iron Ore 2013 , pp 553-560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Muir D. M

Highly saline process water has a number of implications for the CIP process during the leaching, adsorption and recovery of gold. The reduced oxygen solubility in saline water can seriously reduce the rate of gold leaching, while dissolved oxygen meters do not necessarily reveal actual oxygen concentrations in saline water. High levels of magnesium in the ground water necessitate operation at lower pH (-9), with the potential for greater cyanide loss via HCN stripping. In addition increasing salinity renders viscosity modifiers largely ineffective.The adsorption capacity of aurocyanide onto activated carbon is improved with increasing salinity, but misleading results can be obtained in assessment of gold loading kinetics of plant carbon samples already loaded, or partially loaded, in saline water if subsequently tested in fresh water. Elevated chloride levels in the Zadra elution process can cause severe anode corrosion in the elecuowinning cell. The Anglo elution process is tolerant to only slight increases in water salinity, but elution times can be reduced by ethanol addition. Care is required in carbon regeneration, as salts can catalyse carbon decomposition as well as increase kiln corrosion.

Jan 1, 1994

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

By Patridge A. C

A pilot scale laboratory investigation of manual slurry sampling methods representative of those used in the minerals industry is described. Samples were taken from slurries made up from silica particles of various sizes and in various concentrations from a stirred tank and from the discharge lip of a rectangular launder. Sampling methods from the tank included immersion flasks and several configurations of a suction probe. The launder was sampled using a conventional narrow-mouth ladle and also with a 'mouth organ' stream splitter. Samples were analysed for overall solids concentration and size distribution and showed different but always significant and often large biases relative to the known overall composition of the slurry, the nature and extent of bias being dependent on pulp concentration, particle size, sampling method and sampling location. Results clearly show the very great difficulty of obtaining representative samples by simple sampling techniques, although the data suggest that errors can be reduced by using an appropriately designed and operated suction probe. Further work will be carried out with the objective of establishing guidelines for industrial sampling practice.

Jan 1, 1995

By Yusuf R

Many heap and dump leaching processes involve competitive, complementary and sequential reactions between multiple minerals and reagents. A comprehensive model has been developed to deal with these complex chemical interactions which is based on diffusion control of the reaction rates. All of the mineralogical and chemical data are obtained from representative samples of the ore or the chemical literature. These properties have been incorporated in a general way, making the model applicable to a range of ore-process systems. The simulation is used to predict the absolute reaction rates and can be used before any leach tests are carried out on the ore itself. The applicability of the model and some tests of its validity are presented.

Jan 1, 1984

TUNGSTEN occupies an outstanding position amongst metals to-day, for by its use modern manufacturing methods have received a wonderful impetus. The important part played by tungsten in the recent war is not generally recognized. It was tungsten steel, in the shape of highspeed tools, that kept our soldiers supplied with munitions of war at more than one critical period. Tungsten added the necessary hardness and durability to various metals which were indispensable for carrying the war to a successful conclusion. In the words of...

Jan 1, 1921

By King ND

This paper presents an economic study comparing two gold recovery processes, zinc precipitation (Merrill-Crowe) and carbon-in-pulp (CIP). Capital, operating, and gold losses costs from an actual CIP plant study are compared to costs developed from a hypothetical Merrill-Crowe process flowsheet. ' Results indicate an overall economic advantage to CIP over Merrill-Crowe for plants processing slurries within the range of the five gold solution grades selected for this study.

Jan 1, 1982

Mining is an intensive resource development industry, where operations are often of relatively short duration and can result in dramatic impacts on the natural environment during the operational period and for many years post mining. An integral component of all mining operations is water û through exploration, resource definition, mine development and operation, rehabilitation and the long-term post-mining land use. Water is a basic requirement in the provision of worker amenities, in drilling, as a means of dust suppression, as a medium for washing or processing the mine product, and as an aid in establishing vegetation on post-mining landforms. Water also plays an important role in mobilising environmental contaminants and is the primary medium for the transport of contaminants off the mine or processing site into the wider environment. It is for this second reason that the mining industry considers water management as a key component of mine management. Cost-effective water management relies on planning that incorporates a total mine system approach commencing prior to exploration and continuing through to rehabilitation and decommissioning. One of the primary considerations that will provide confidence to both government and community at the time of mine closure and lease relinquishment, will be the evidence that any water originating from, or passing through, the mine site is of a quality that will not have any negative impact on the surrounding environs into the future. The role of vegetation in stabilising disturbances to a landscape is well known, as is the recognition of vegetation being a fundamental component of the water cycle through the physiological processes resulting in the transfer of water back to the atmosphere through transpiration. In terms of water management at a mine site, the two crucial issues are the æquantityÆ and æqualityÆ of water that enters a receiving æoff-leaseÆ catchment. In terms of tolerances of the receiving environment, the total load of potential contaminants becomes critical, a reduction in which can be achieved through reduced volumes of water discharged, reduced chemical and physical concentrations of contaminants in that water, and ideally, both. This paper examines the potential role of vegetation in reducing the quantity of water released from a site, and secondly considers vegetation in the role of influencing the quality of that water.

Jan 1, 2003

In South African gold mines, the types of material requiring transportation to the stoping areas include timber packs, explosives, hydraulic rock props, scrapers, scraper winches, pipes, pumps and backfill material (in areas where backfill is being used). Currently timber packs are broken down to their basic components (log and brick) and are transported into the stope by means of either monowinches or a combination of monowinch and scraper winch. Other materials, such as explosives, hydraulic rock props, scrapers, scraper winches, pipes, pumps and backfill material must be transported by other means, usually by hand or, in the case of heavier items, by chain blocks. With the drive to increase stope advance rates and the rise in the number of miners with HIV/AIDS, there is a need in the South African gold mining industry for an improved material handling system. To meet future requirements, material handling systems should assist miners to transport materials quickly and efficiently. Furthermore, it must be financially viable and economically competitive with current material handling systems. This paper looks at the in-stope material handling efficiency of current monowinch systems and provides solutions to improve efficiency. In addition, the use of in-stope monorails are reviewed and the possible scenarios that will substantiate the use of monorail systems are discussed.

Jan 1, 2003

The changing characteristics of raw materials has highlighted the limitations that conventional vibrating screens have in the handling of fine wet sticky materials. These' limitations have led to the development of a totally new concept of screening, the Rotating Probability Screen. In order to illustrate the practical benefits to be gained by the extraction of fine materials ahead of subse quent processes particularly in the coal industry, the experiences gained in Ro-Pro installations in America, Australia, Europe and Britain are drawn upon.

Jan 1, 1984

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981

The Sto Tomas II orebody of Philex Mining Corporation is a porphyry copper deposit located at Padcal, Tuba, Benguet, Philippines. It was mined through open pit method for the first two years starting 1958 and subsequently through underground method using the Block Cave System. The slusher type of draw was employed at the upper levels of the orebody from mid-year of 1959 up to 1994 and then shifted to LHD as the ore became more competent at the lower levels. Application of rock mechanics played a vital role during the conceptualisation of the LHD method of draw, the first of its kind in the Philippines. Rock mechanics is a combined responsibility of the geology and the mine engineering staffs, with the geology providing the vital information to the mine engineering to include in the mine planning the following:the general geology of the orebody; the ground characterisation through rockmass classification; determination of the cavability of the ore column (this includes our experience on airblasts which occurred during the early stage of our last slusher blocks); undercutting sequence; fragmentation of the rockmass in the ore column; drawzone spacing; proper draw control procedure; lay-out of openings; and the design of ground supports based on the rockmass condition. For the proper interpretation of the rockmass that would cater to the diverse mining situations, Philex adopted the modified geomechanics rockmass classification (Mining Rockmass Rating, MRMR) as this system is recognised and used by most of the block cave mine worldwide. This paper aims to discuss and present the role of rock mechanics in the analysis and determination of geomechanical issues encountered in Philex mechanised block cave operation.

Jan 1, 2000

By Alford R. A

The causes of the loss of heavy mineral from mineral sands wet concentrators were identified through detailed surveys of two such concentrators. It was found that tray and spiral sluices preferentially lost elongated panicles, but panicle size had little effect on loss. Recovery was shown to increase with panicle density. The major influences on the recovery efficiency of individual concentrating devices (stans) were feed rate and feed grade, recovery increasing with decreased feed rate and with increased grade. Uneven distribution of total solids and heavy mineral to individual stans contributed to losses through the corresponding effects in feed tonnage and grade. Computer simulation demonstrated that significant recovery improvements could be obtained by appropriate adjustment of splitters to optimise the characteristics of internal plant flows.

Jan 1, 1991