Search Documents

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By Andrews S. J

Century is a shale hosted zinc, lead, silver deposit developed within gently folded, Proterozoic Lawn Hill Formation shales and siltstones, approximately 250 kilometres north-northwest of Mount Isa, comprising 118 million tonnes of stratiform mineralisation, averaging 10.2 per cent ,,inc, 1.5 per cent lead and 36 grams per tonne silver. The deposit is largely overlain by Cambrian limestone and younger Proterozoic sedimentary rocks, outcropping at only two places. Small discordant lode lead-silver deposits formed the basis of relatively small scale mining activity in the area for almost 100 years, exploration tenement covering the deposit being granted to CRAE exactly 100 years after the first mining leases were pegged in the area in 1887.Stratiform mineralisation occurs within three distinct blocks, bounded by normal faults and the unconformity between Lawn Hill Formation and overlying Cambrian limestones. The Termite Range Fault, a major northwest trending, regional scale fault system occurs adjacent to the northeast deposit boundary, while the Magazine Hill Fault, possibly a component of the east trending Little Range Fault system, forms the southern boundary of the deposit.

Jan 1, 1993

By J Araya, O Leiva

The mine evaluation process, composed of the designing, planning and valuation of a mine project, is, among other variables, based on an estimated orebody model. However, as the information from the drill holes is limited, it is impossible to know with certainty the mineral content in each block within the estimated block model. Consequently, uncertainty about the value of metal grades, or other geological attributes, arises because of the lack of information at unsampled locations. This is one of the reasons why, in any mine operation, there will always exist a divergence between estimated and real values. Cut-off grade optimisation is the process used to determine the operating mining strategy (long-term production scheduling) that will maximise the total profit value (normally referred as the net present value (NPV)) of a mine operation. This is done by defining a dynamic cut-off grade policy which is constrained by the production capacity of the mining, mill and refining.Real options is a type of contract, written on real assets such as mining, oil and other natural resource industries, that gives you the right but not the obligation to exercise the contract. It is based on operational and managerial flexibility, which allow mine decision makers to react to either good or bad operational and economic events in the future. But, what do geostatistics and cut-off grade optimisation have to do with the application of real options in a mine project evaluation process? The objective of this paper is to answer the previous question by showing how geostatistics combined with cut-off grade optimisation are key tools for corporate/managerial decision makers, which allow them not only to analyse the resource/reserves of their projects, but also to generate operational strategies that can maximise project value by minimising the downside risk due to ore tonnes and grade uncertainties, while achieving operational and physical constraints such as mining and processing capacities. A real copper grade open pit mine project is used as a case study.

Sep 26, 2011

By L Whitbourn, K Yang, P C, E Ramanaidou

The potential of hyperspectral mineral mapping within a mine environment is demonstrated. Central to this capability has been the development of portable or vehicle-mounted, hyperspectral mine face-mapping systems. Data from these systems were used to detect subtle mineralogical variations and map their distribution across rock faces in a fashion that previously was not possible. In one study, the data usability was enhanced by ædrapingÆ the mineralogical determinations over a three-dimensional æmodelÆ of the rock-face. The eventual melding of the spectral mine face-mapping and three-dimensional spatial technologies will result in a new generation of mineralogical and structural information becoming available to mine geologists, engineers and metallurgists. Specific uses for spectrally-derived, mineral mapping data sets could include:ore grade mapping systems based on either direct detection of ore minerals themselves (eg iron and nickel oxides), or mineralogies that may be used as surrogates for ore-grade information (via various alteration minerals) after a suitable orientation survey; detecting mineralogies that have a deleterious effect on milling, metallurgical processing or have occupational health implications (talc, swelling clays, carbonates, asbestos, etc); selective mining and blending by collecting, processing and displaying such mineralogical images in near real-time to monitor ore grade and quality, and allow the separation of ore from waste during loading operations at the mine face; a mineral detection and mapping capability to assist in structural and geotechnical mine planning applications; and an enhanced geological detection and mapping capability for ore mineral species or alteration mineralogies that may be used to vector further mineralisation, update the existing mine ore model, or provide input to assist in the control of autonomous mining equipment. Within the Woodlawn open pit, Fe- and Mg-chlorites and phengitic- micas associated with sulfide mineralisation were detected and mapped. Subsequent studies using a second generation face-mapping system demonstrated the direct detection of ore-grade materials for iron-ore and nickel laterite mining activities. Satisfactory and meaningful results were extracted from data that were collected under a variety of challenging conditions. However, these non-ideal climatic and operational conditions would be expected under most operational situations in a mine environment. Development of a system using artificial illumination, permitting night-time (and eventually underground) operation and elimination of atmospheric absorption effects is underway.

Jan 1, 2006

By Rogis J

The basic parameters causing outbursts are rock pressure, gas characteristics and the physico-mechanical properties of the coal. The three sets of factors are to some degree interdependent. At Collinsville, the gas characteristics coupled with the physico-mechanical properties of the coal appear to be the major factors contributing to outbursts. The relative importance of rock pressure is uncertain. The following geological parameters appear to be necessary before outbursts can occur. 1. A coal rank greater than 1.2% vitrinite reflectance. 2. Thrust faults with throws greater than 3.Om or strike- slip faults with coal gouge wider than 0.3m. 3. Seam gas emission values greater than 1.1 cm3 /g. Igneous intrusions are the likely source of the carbon dioxide seam gas. Outbursts have occurred at depths ranging from 215m to 265m. They occur at these relatively shallow depths due to: 1. the high rank of coal at the present topographic surface and the high coalification gradient; 2. the relatively high degree of tectonic deformation of the strata; 3. the seam gas characteristics; and 4. the extent of igneous intrusions.

Jan 1, 1980

By Jaques A. L, Heinrich C. A

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

Exploration for uranium in Australia has so far discovered reserves equal to 17.5% of the Western World's. The Australian uranium industry, when fully developed, will be one of the largest producers and possibly the largest exporter in the world. The world's nuclear industry is young, rapidly developing in size and technology and is subject to more social, political and regulatory controls than any other industry. This paper considers the probable development of Australia's uranium industry against a background of normal commercial parameters together with other factors which are peculiar to the nuclear industry. As the theme of this conference is "Australia's role in the World Mineral Indus- try" this paper concentrates on the commercial and practical aspects associated with the development of Australia's uranium resources in a world context.

Jan 1, 1979

To obtain the best economic results in treating the comparatively high-grade ore of the Kalgurli Mine a good roast is essential, and the effort of this paper will be to briefly describe the plant and the conditions prevailing in roasting, which, on an output of about 360 tons daily, subsequently enable an average extraction of slightly over 94% of the gold to be maintained.The percentage of sulphur in the ore varies between 2'5 and 3'5, the lower figure existing when treating oxidized ore. The average gold value is 13 dwt; this occurs chiefly as sylvanite, containing .a lower percentage of silver than is usually present in that mineral. One ore body in the mine contains hessite (Ag2Te) in considerable quantity, associated with gold telluride, and when ore from this stope is being treated the silver contents rise to as high as 20 dwt, but the usual amount is about 9 dwt. per ton, of which only a small proportion is extracted. Other metallic minerals, in addition to pyrite, occurring more or less commonly, are arsenopyrite, magnetite, chalcopyrite, and the tellurides calaverite (AuTez)and coloradoite HgzTe3). A small proportion only of the value occurs as free gold.

Jan 1, 1911

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

By Nemcik JA, Gale W. J

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ

Jan 1, 1992

The Mary Kathleen uranium deposit occurs in 1740-1780 M yr-old calc-silicate melasedimentary and mela-igneous rocks of lhe Corella Formalion which have been tightly folded into lhe Mary Kathleen Syncline. The Corella Formation consists of malic and felsic tuffaceous(?) calc-silicates, quartzile, and minor marble, conglomerate and basic volcanics. Garnet-rich rocks form semi-concordant and transgressive masses in the middle and upper portion of the sequence. Granite, gabbro and acid porphyry dykes also occur in the syncline.Uranium-rare earth mineralisation is closely associated with certain malic rocks and occurs wilhin or close to garnet-rich masses. At Mary Kathleen, uraninite grains are enclosed mainly by allanite which is dislribuled through massive garnet as an irregular honeycomb of interconnected shoot and lenses. The mineralisation occurs along strike from dioritic rocks and conglomerate and lies close to the axis of the Mary Kathleen yncline and adjacent to a major faull zone. All other localities allanite-uraninile mineralisation is broadly stratiform.The mineralisation is interpreted to occur at or near centres of basic volcanism. Garnet formation and uranium-rare earth concentrations are believed to be caused by the volcanism, and to be contemporaneous with it. The former is seen as alteration of a hot, saturated pile of volcano-sedimentary material and the latter as intermittent hydrothermal exhalation.Deposition, volcanism, garnet formation, uranium and rare-earth mineralisation, granile and gabbro formation, and tectonism are seen as a continuum of interrelated processes which operated throughout the period of format ion of the rocks in the Mary Kathleen Syncline.

Jan 1, 1985

By T J. Sheer

The removal of airborne pollutants from underground ventilating air is discussed. The work concentrates on the removal of CO, CO2, NOx, SO2, radon gas and respirable carbon particles. The investigation combines techniques for multiple contaminant removal using forced chemical absorption and oxidation. Both dry and wet scrubbing techniques are employed. Mixed success has been achieved in the tests carried out and this paper is seen as a progress report on the work done to date. The interference and interaction of the gases on the individual removal efficiencies is a very important factor in the finalisation of a macro air conditioner (MAC) design for treating underground ventilating air. This necessitates a specific sequence of contaminant removal. Efficiencies are discussed and recommendations made. Wet forced chemical absorption and oxidation processes, though efficient in terms of removal efficiencies, cannot be employed in the confined underground environment due to safety and health risks. Impacts on the internal water reticulation systems of the mine have been analysed to determine the effect of future large-scale macro air conditioning practices, including blow-off liquids discharged into the water circuits. To engineer the safety and health risks out of such designs can be costly and it is for these reasons the research now concentrates on dry scrubbing of the contaminants from the underground ventilating air. The paper concludes with statements on the benefits of macro air conditioning in deep hot mines, in both recirculating and series air ventilation distribution strategies. These benefits include reduced re-entry times after blasting and increased production rate opportunities.

Jan 1, 2005

By Jankowski P

The Bannockburn gold deposit is located 67 km north-west of Leonora in a poorly exposed part of the Norseman-Wiluna belt of Western Australia. The deposit consists of narrow, complexly shaped orebodies which have presented a challenge to find successful grade control and mining methods. The deposit also presents an opportunity to examine in detail the geology of this part of the Norseman-Wiluna belt.This paper discusses the geology and structure of the Bannockburn gold deposit as well as the grade control and mining systems developed to define the ore and extract it with minimum dilution. We discuss the different techniques employed for grade control in the past and their shortcomings, and the evolution of the present system of doing grade control in cross section from blast hole assays.

Jan 1, 1993

By B Huls, B E. Smith, I Brake, M Yu

A brief outline of some of the pioneering events in the development of flotation technology, which originated in Broken Hill at the start of the 1900s, is presented. The development of the original Potter-Delprat process, the introduction of oils to generate froth flotation and the achievement of selective flotation processing are described, all focussed on solving challenges with the Broken Hill Pb-Ag-Zn ores. Some recent initiatives in flotation at BHP Billiton operations are also outlined, covering coal, copper, lead-silver-zinc and diamonds. Some views are offered on the characteristics of innovation in flotation and on possible trends into the future.

Jan 1, 2005

By Okura T, Hino J

Coal utilization for copper flash smelting in Japan was initiated due to the sudden upheaval in the price of oil in the last ten years. A major portion of the heavy fuel oil has already been replaced by coal resulting in a corresponding decrease in energy costs. In addition to energy cost savings, an interesting metallurgical phenomenon was observed in flash smelting operations. Unlike oil combustion, coal is not burned completely in the shaft. A considerable fraction of coal particles remain on the surface of slag and are burned at the settler. Chemical investigation has shown that oxygen potentials at the settler have consequently decreased, bringing the slag and matte phases into reducing conditions, thus oxidation and reduction can coexist in one flash smelting unit. As a result, a decrease in magnetite and copper contents in the slag, elimination of furnace hearth build-up and dissolution of intermediate layer between matte and slag have been observed. In general, these led to improvements of furnace operations. However, thermodynamic investigations have shown that some minor elements such as As, Sb, Bi and Pb concentrate from slag to matte. Results evaluated on the basis of thermodynamic data relatively agree with practical observa- tions. Consequently, for coal utilization in flash smelting operations it will be necessary to control oxygen potentials from the stand- points of copper loss in slag and minor element Distributions.

Jan 1, 1987

The disadvantages of the present zinc producing methods, RLE and ISP, are high energy consumption and environmental problems. Therefore, efforts have been directed in Outokumpu Zinc towards the development of alternate routes. One interesting pyrometallurgical process to produce zinc is to inject zinc calcine together with a solid reductant into molten iron, saturated with carbon. This process has been studied by thermodynamic calculations, laboratory tests and mini-pilot test runs at Outokumpu Research Oy, Pori, Finland. The results of these tests are presented and discussed in this paper. The mini-pilot tests demonstrated that over 97 per cent evaporation of the zinc was possible using a reactive coal dust as the reducing agent. The recovery of zinc in the metal phase was at best 88 per cent of input zinc, but only part reported in molten lead in the splash condenser. The final metallic zinc contained at best 98 per cent Zn, the main impurities being dissolved lead and coal carried along with the flue dusts.

Jan 1, 1993

By Brzezniak W

Conversion to trolley assist is a means of minimizing diesel fuel consumption, which in many mining situations offers a rapid payback of capital investment plus the inherent flexi- bility and maneuverability of truck shovel op- eration. Whendiesel electric truck shovel mining opera- tion with trolley assist is compared to alter- native mining methods such as conveyor systems, the trolley assist system can be easily justi- fied in terms of return on investment, payback and increased productivity. A review of present technology, performance requirements and past experience in the min- ing industry has led to the development of a trolley assist system for diesel electric haulage trucks which, is proven in the mining environment, offers significant reduction in fuel consumption and increased productivity.

Jan 1, 1981

By Ishikawa K, Kikuchi T, Tokairin Y

Roadheader, developed from coal cutting machines, is generally classified as a tunnel excavation machine for soft rocks in respect to excavation mechanism, machine structure, weight, engine output and so on. In recent tunnel works, however, there is an increasing demand for changing from blasting to mechanical excavation by roadheaders to avoid environmental problems such as noise and vibration. But there exist various difficulties in excavation of harder rocks by roadheaders. In order to explore the possibilities of roadheader excavation, we performed field and laboratory experiments. In the field experiment, roadheader model S-125 (Mitui Miike Machinery Co.,Ltd.) was tested for various rocks of wide range of hardness, and excavation capacity and wear of picks were measured. In the laboratory test, cutting performance of the picks was tested by our cutter testing machine. This report describes thr: of these experiments and discussions :n possibility of applying boom-type tunnelling machines to hard rock excavation based on these experimental data.

Jan 1, 1987

By G Mudd, N Haque, S A. Northey

Life cycle assessment (LCA) provides an internationally standardised framework for estimating the environmental impacts associated with products or services (International Organisation for Standardisation, 2006). A particular strength of LCA is the ability to consider indirect impacts that occur at different stages of a product’s life (eg raw material acquisition, manufacture, use, disposal or recycling) and through its supply chain (Figure 1). A wide variety of impact categories are able to be considered by LCA, such as the potential contribution to global warming, ozone depletion, marine eco-toxicity or freshwater eutrophication.CSIRO has a long history of using LCA to compare the environmental impacts associated with alternative mining, mineral processing and metal production technologies (Haque and Norgate, 2014; Norgate and Haque, 2012, 2013). These ‘mine-to-metal’ assessments have primarily focused upon estimating embodied energy and greenhouse gas impacts associated with these production processes; however, more recently there has been a refocus to also consider consumptive water-use impacts in more detail (Northey et al, 2014).CITATION:Northey, S A, Haque, N and Mudd, G, 2016. Water-related data requirements for improved life cycle assessment of mining, mineral processing and tailings management, in Proceedings Life-of-Mine 2016 Conference, pp 16–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By P D. Franzmann, D J. Readett, J Peterse

A better connection between laboratory- and pilot-scale test results, and heap bioleaching performance can be achieved by generating reliable information on the fundamental microbial, chemical and physical processes that occur in heaps and incorporating this information into a comprehensive and robust model. More efficient heap bioleaching, particularly of chalcopyrite, has the potential to add value to the mining industry as well as deliver attractive environmental and social benefits to the communities within which those companies operate.The results of fundamental chemical and microbiological studies of the leaching mechanism, the temperature dependence of chalcopyrite bioleaching, and the optimisation of leaching conditions are described with examples from full-scale heaps. The development and application of a number of novel techniques and tools has assisted our understanding of heap subprocesses mineralogy, hydrology, chemistry and microbiology. The heap bioleaching model HeapSim, which embodies a large number of effects not previously accounted for in other models, continues to be refined and has been applied successfully to the study of several heap bioleach systems.

Jan 1, 2004