Search Documents

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The distribution of p(~rphyt1 copper deposits, in time as well as place, is used to propose an occurrence model based on the genesis models of Sillitoe and Rona. A magmatic source of the metals is accepted. The characteristic metallogenic epoch and the migration of the mineralization event along an elongate metal province are explained as the result of subduction of an obliquely- oriented strip of mineral-enriched material on the oceanic plate. Two mineral-enriched trails emanate from a hot-spot source of high-intensity hydrothermal activity in an oceanic rift. Because the whole plate system moves relative to hot spots, the hydrothermal source appears to migrate along the rift, and the two trails are not parallel to transform faults, but form a broad "V" centred on the hotspot. Source loci are spaced at intervals of about 3000 km, resulting in the possible repetition of metallogenic epochs, in a subduction zone province, at about 100 m.y. intervals. The position of the mineral-enriched strip can be found graphically, given ages of a series of deposits in a province, and the plate convergence vectors. This knowledge provides an exploration tool at regional scale and, by reflection across the rift, the potential for exploration is extended across oceans. The model has implications for commodities and deposit types other than porphyry coppers.

Jan 1, 1987

Lake Kopiago is located some 71km northwest of Tari in the Southern Highlands Province and lies on the northern edge of the Papuan Fold Belt. The area is underlain by middle Miocene carbonate and fine grained clastic sediments intruded by late Miocene hornblende gabbros.Two mineral deposits occur to the south of Lake Kopiago. These are the Bisamu gold prospect and the Wunaki zinc-lead gossan.The Bisamu deposit consists of a calcic skarn assemblage which is geochemically anomalous in gold, silver, copper, zinc, cobalt, bismuth and tellurium. The prograde mineral assemblage includes garnet, clino-pyroxene and epidote whereas the retrograde assemblage includes epidote, quartz, actinolite and chlorite. Pyrrhotite is the dominant sulphide with minor pyrite and marcasite and trace chalcopyrite and sphalerite. Minor magnetite is also present. The Bisamu skarn shows many of the features typical of gold-skarn type mineral-isation.

Jan 1, 1994

By R van Wyk

In today’s mining environment the use of heavy mechanical devices and other high-tech electronic devices like two-way radios, cellular phones and even automated mining systems, form a vital part of the daily operations of a mining site. These human-made devices and some of the naturally occurring events, like lightning and gamma radiation, can have negative effects on electronic detonators and the associated control equipment.On larger mining operations the necessity to move the point of safety for blasting further away from the blast area, introduced remote firing via radio frequencies for electronic detonator systems. Other influences on electronic detonators can be abuse or ignorance. To ensure the safety of the end-user, an electronic detonator must be resistant to some common mistakes that users can make. One of main concerns here is resistance to static discharge or incorrect wiring. Despite the daily use of electronic detonator solutions, scepticism and concern still exists amongst those who believe the system raises the risk of a premature initiation of the blast through some form of interference trigger.This paper will help users understand how electronic detonators and the associated control equipment protects itself from external influences. Focus will be on protection schemes to counter static and over-voltage discharge and methods to ensure protection of secure wireless radio links and detonator communications. With well engineered communication systems and solid static and over-voltage protection, an electronic detonator system can be more reliable and safer than other detonator systems. The following main points will be discussed:what makes a detonator an electronic detonator,static electricity and over-voltage protection,the general influence of electromagnetic energy on the detonator,the influence of lightning on detonators,the protection of radio communication’s links as used by remote firing equipment, andthe safety protection features built into remote firing equipment.

Nov 8, 2011

My purpose here today is to introduce an element of democracy into this seminar. In my experience, the mines of Australia can be divided into two categories; those that pay and those that don't. As far as I can ascertain, every other paper being delivered at this seminar concerns mines which come into the first category, or at any rate are close enough to it for the promoters to be able to afford an expert's valuation.

Jan 1, 1989

By G Nicholas, S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

"A new approach to mineral project evaluation is described called Scenario-Based Project Evaluation (SBPE). SBPE incorporates well established æscenario planningÆ and æscenario thinkingÆ approaches, which are used extensively in other industries,?most notably the?petroleum industry. While most scenario planning is qualitative and non-probabilistic, the approach described here includes both quantitative and qualitative aspects. SBPE is complementary to optimisation approaches and allows mining firms to build and operate projects that are more robust in the face of adverse changes as well as proactively respond and exploit the upside offered by a realistic assessment of variability. The approach has potential to improve project performance and decrease operational risk. It also has important applications for currently operating mines.Conventional evaluation of metalliferous mineral deposits uses estimates of metal grades and deleterious attributes in singular æorebody modelsÆ, usually 3D block models, which fail to capture two critical aspects that underpin the realised value of mining projects: the inherent uncertainty of the estimated attributes the spatial variability of attributes, at the scale of mining selection, which impact on downstream processing steps and fundamentally drive realised value. While singular models are appropriate for estimating block averages, conditional simulation (CS) models of the relevant attributes are needed to represent uncertainty and capture spatial variability. Any attributes that can be either built into CS models and/or modelled in the envisaged mining/processing steps, can be evaluated fully through to highly ægranularÆ (ie detailed and un-smoothed) cash flows. A complete view of SBPE relies on selected strategies being tested against plausible æscenariosÆ of factors external to the project and thus outside management control. æExternalitiesÆ captured in such scenarios include market prices, costs and taxes. Via SBPE, project managers may demonstrate that there is material value in preserving or purchasing options that provide future flexibility to respond to the changing externalities or changes in orebody performance. Such flexibility generally comes at a cost but is very difficult to value. It is argued that full value chain evaluation using SBPE can help to value these options for a mining company. A case study for a gold mine is presented.CITATION:Vann, J, Jackson, S, Bye, A, Coward, S, Moayer, S, Nicholas, G and Wolff, R, 2012. Scenario thinking - A powerful tool for strategic planning and evaluation of mining projects and operations, in Proceedings Project Evaluation 2012, pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By F J. Rios

In the eastern high-strain domain of the Quadrilßtero Ferrffero, Brazil, hard and soft high-grade hematite ore may occur as schistose bodies in shear zones mainly related to the Cambotas-Fundpo thrust system. These orebodies are almost entirely constituted of oriented specularite platelets that develop both as a product of crystal-plastic deformation of hematite and solution-precipitation processes. Both mechanisms interact in the partitioning of the strain, while solution-precipitation is responsible for the precipitation of hematite and localised leaching of silica resulting in the formation of syntectonic ores. The analyses of fluid inclusions from specularite crystals of the Conceitpo and Timbopeba deposits, located in the northern and southernmost areas of the eastern high-strain domain of the Quadrilßtero Ferrffero, were studied using infrared microthermometry and Synchrotron x-ray fluorescence. The results indicate the participation of highly saline aqueous H2O-NaCl fluids containing other additional cations (Ca, Fe, K and probably Ti) in solution and homogenisation Temperature (Th) averaging between 130¦ - 190¦C. However, the partial fusion of metastable saturation phases indicates crystallisation temperatures of approximately 400¦C. The mineralisation process produces high-grade orebodies as well as Fe-rich specularitic itabirites that are explored in that area. The shear zones are related to thrust faults mapped and interpreted as related to the PanAfrican/Brasiliano Orogeny that affected the Quadrilßtero Ferrffero, thrusting the Paleoproterozoic platform sequence of the Minas Supergroup over Mesoproterozoic quartzites of the Espinhato Supergroup. They intersect and even overprint an early metamorphic and tectonic fabric of Paleoproterozoic age (Transamazonian Orogeny). The geological and fabric relationships lead to the conclusion that the fluids involved in the mineralisation were most probably of external origin, of still unknown source (possibly igneous), during the closure of the Spo Francisco Craton.

Jan 1, 2005

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

By O Omidi, P D. Katsabanis

The effect of delay time on fragmentation has been discussed for a long period but rarely in a satisfactory and unbiased way. Despite the efforts of many researchers, delay selection for fragmentation improvement or optimisation remains a controversial issue. Large-scale tests have been plagued with scarcity and scatter of observations, while small-scale tests have been associated with boundary effects and energy losses. Theoretical work is often used to produce explanations for available measurements or tries to simplify wave propagation and wave interaction to guide observation and practical work. The present work analyses results obtained from a relatively large number of small-scale experiments in blocks made of grout, and re-analyses results of previous experiments, to conclude on the effect of delay on fragmentation. It is shown that the main contribution of the delay is found in the fragmentation of the larger fragments of the blast, while the small fractions show almost no effect. Samples, where copper liners were used to inhibit penetration of detonation products in the rock mass, showed effect of delay only when short times were used and steady but poor fragmentation when long delays were used. Based on small-scale experiments, it appears that the fragmentation is optimised when a hole fires prior to the radial cracks, produced by the previous hole, reach the free face of the blast. Gas penetration may result in the development of few more fractures that affect the fragmentation of the largest particles of the blast.CITATION:Katsabanis, P D and Omidi, O, 2015. The effect of delay time on fragmentation distribution through small- and medium-scale testing and analysis, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 715–720 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The Pongkor Gold Mine employs 678 staff. The mine is owned by the Indonesian state company PT Antam Tbk and is located 100 kilometres south west of Jakarta, in Java, Indonesia. Mine and infrastructure development started in 1992 following intensive geological exploration over 15 years. First gold production was in June 1994. The mine comprises three main orebodies: Ciguha, which is nearly mined out, dips at 75¦ from surface to 150 m. Kubang Cicau, dipping at 80¦ from surface to 230 m, and averages 3.5 metres thick at a grade of 10 g/t Au and 128 g/t Ag; and Ciurug, dipping at 60¦ from surface to 300 m and averages eight metres thick at a grade of 14 g/t Au and 172 g/t Ag. Present global ore reserves are 4.6 million tons at a grade of 12.3 g/t Au and 133.6 g/t Ag. Exploration is continuing for new veins. Initial mining was by manual cut and hydraulic fill at Ciguha, followed by Kubang Cicau. In 1996, it was proposed to convert Ciurug to a mechanised cut and fill operation. Two single boom jumbos and three load-haul-dumps (LHDs) were purchased with the assistance of a gold loan from NM Rothschild and Sons. Implementation of this upgrade was delayed by both a national economic crisis and an invasion of the concession by illegal miners. It was not until May 1999 that raise bore vent rises and access drift infrastructure commenced. Major underground development started in 2000 and is continuing. Production cut and waste fill stoping started in July 2001. The change from manual to mechanised methods has required a total change in work practices and attitudes. However, the process has resulted in a production increase from 600 tpd to 1200 tpd. A three-month compliance test (a condition of the financing loan) was successfully completed, from July to September 2001, with an average production of 700 tpd at Ciurug and 500 tpd from Kubang Cicau.

Jan 1, 2002

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

By E Whiteman, L Reyneke, H Horsch

Heavy mineral sand deposits are a source for the economically important element titanium, which is contained in minerals such as ilmenite and rutile. In heavy mineral deposits ilmenite displays various degrees of alteration. Natural weathering of ilmenite involves the removal of Fe and thus results in an increase in the Ti-content. Minerals such as pseudorutile, ferropseudobrookite, anatase and the ill-defined mineral aggregate leucoxene, which consists mainly of various amounts of remnant ilmenite, pseudorutile, ferropseudobrookite and anatase, are typical replacement products of ilmenite. Ferropseudobrookite occurs as a recrystallised, optically and chemically distinct mineral phase. Textural relationships suggest a diversity of physicochemical conditions including weathering and metamorphism that led to the formation of complex mineral assemblages and textures. In the heavy minerals industry the alteration products of ilmenite are generally referred to as æaltered ilmeniteÆ and/or leucoxene. The distinction between æaltered ilmeniteÆ and leucoxene is not consequently defined and is very much dependent on economic factors and specific mining operations (ie determined by deposit specific mineral assemblages). Generally the term leucoxene is used in the heavy minerals industry as a collective description for ilmenite alteration products with TiO2-components ranging from 65 - 95 per cent. A detailed comparative mineralogical investigation including microscopic, SEM and QEMSCAN« techniques show that it is possible to identify and quantify the replacement products of ilmenite on a micron scale. QEMSCAN« generated particle maps were graphically compared with photomicrographs taken by applying reflective light microscopy. The resulting information can be integrated over the entire sample with respect to composition, absolute and relative mineral abundances, grain sizes, volumes, densities, textural relationships and liberation potentials. This provides a powerful tool for a first appraisal of the physicochemical behaviour of bulk samples and individual particles during metallurgical processing.

Jan 1, 2008

By C Zhang, I Canbulat, S Saydam, H Yu, H Chen

Natural rocks are frequently exposed to groundwater and complex geological conditions. Environments with water presence are more susceptible to chemical corrosion, which notably affects rock’s micro properties. Generally, the pH of acid mine drainage in hard rock mines can be low to 5, and the pH of quarrying waste deposits can be below 3. With the expanding scope of mining engineering in aquifers and salty areas, chemical corrosion can also caused by different types and concentrations of anions. The anions can significantly affect rock’s mechanical properties. Therefore, it is critical to emphasise the impact of anion and acid on the mechanical and micro characteristics of rock. This paper commences with an introduction to representative corrosive environments. Then the UCS tests are conducted on granite samples corroded by chloride ions and sulfate ions. Anion has negative effects on the strength of granite. The reason is that certain minerals can react and be dissolved by anions and hydrogen ions, such as Al2O3. Furthermore, the scanning electron microscope (SEM) shows that the roughness of the fracture surface increases with the anion concentration. The effect of acid is notably more pronounced than anion on the micro properties of granite. The initiated fissures and pores also increase with the concentration of SO42- and Cl- ions, which is the micro explanation for the impact of anion on rock strength and stability. Subsequently, the permeability of the granite specimens is tested. The reason that granite performs insensitivity to acid and anion is attributed to its low permeability and high content of inactive oxides, such as quartz. To summarise, anionic and acidic conditions can slightly deteriorate the mechanical and micro properties of granite. While SO42- demonstrates a higher level of corrosiveness on granite than Cl-.

Sep 1, 2024

By F R. A Jorgensen, G W. Jensen

A pilot scale experimental investigation of the condensation of zinc vapour from smelter off-gases was performed in conjunction with a mathematical modelling study of the system. The work investigated the feasibility of using the high heat and mass transfer rates associated with a fluidised bed to condense zinc directly from smelter off-gases containing zinc vapour. Of particular interest was whether zinc would revert to zinc oxide during the process of condensation, and whether a zinc fog would form and be carried out of the condenser. A 0.1 m diameter fluidised bed condenser was mounted on the top of a 200 kVA DC electric arc furnace in which mixtures of vapours and gases were generated at 1150 - 1300¦C. The gas/vapour mixtures investigated included Zn/N2, Zn/N2/CO/CO2 and Zn/N2/H2/H2O. Greater than 90 per cent of the zinc was deposited on the zircon sand bed of the condenser, and there was no sign of zinc oxide formation, suggesting that the rate of heat transfer was faster than the reaction rate for zinc oxide formation. There was also no evidence that fog was being formed in the condenser. Using the methods of Kunii and Levenspeil (1991), a mathematical model was developed to predict the behaviour of the fluidised bed condenser. The model enabled the distribution of gas/vapour temperature and bed temperature to be determined as a function of distance from the condenser inlet. Similarly the partial pressure of zinc vapour in the gas mixture, and hence the mass transfer rate of zinc to the particles, was determined. Experimental data allowed validation of the predicted bed and gas/vapour temperatures.

Jan 1, 2000

By S Nowosad, A Binder, O Langefeld, M Bothe-Fiekert, F Apollo

The mining industry faces complex and urgent challenges driven by an increasing demand for raw materials, and a socially demanding globalised world. The extraction of primary raw materials is today more important than ever as one of the cornerstones towards a sustainable future since the increasing demand for the raw materials required for the energy transition. In the last three years, leading countries as USA, China, Canada, Australia, and the European Union (EU) have developed and adopted strategies to enhance domestic extraction capabilities, diversifying sources, fostering innovation in recycling, and promoting international collaboration related to critical raw materials. On 2022, the Inflation Reduction Act was signed into law in the USA, in June 2023, the Australian Critical Minerals Strategy 2023–2030 was published and in March 2024, the Council of the EU adopted the European Critical Raw Materials Act. On the other hand, raw materials extraction is facing higher environmental and safety standards and regulations, as well as scrutiny from the broader public. Regrettable environmental accidents as tailing dam failures or acid mine drainage occurrences have led to a general distrust of mining activities leaving mining companies with the dual imperative of increasing output while implementing sustainability, decarbonisation, and circularity as a core value in their production processes. This challenging environment offers the opportunity to enhance ‘blue mining’ (BM) as a sustainable holistic approach that integrates the principles needed to plan sustainable, reliable, and responsible mines for today’s and future generations by implementing the principles of circular economy (CE). This requires a fundamental shift from the traditional linear economy approach to a sustainable, circular economy strategy. At its essence, BM encapsulates four crucial aspects – energy, ergonomics, water, and circularity and integrates these four aspects into integrative mine planning, defining clear goals and objectives from the ‘blueprint’ of a mine towards a beneficial post-mining activity. Its implementation can lead to maximisation of resources beyond the life of the extractive mine and sustainable use of materials by integrating the principles of circular economy and multiuse mine, see Figure 1. These concepts complement and recognise the need to minimise environmental and social impacts while advancing economic development. Finally, this contribution explains the requirements and challenges of moving from linear to dynamic planning approaches under the BM concept. This way, BM stands as an approach that can contribute to the mining industry receiving necessary approvals and support from society leading to a long-term transformation of the industry’s image.

Sep 1, 2024

By Dip L. B

This paper describes the new legislative regime that will apply to the regulation of the minerals industry in New Zealand.The reform of New Zealand's minerals legislation was initiated in January 1988 when the Minister for the Environment, Rt Hon Geoffrey Palmer, announced the Government's intention to review all the major laws governing New Zealand's resources. The Resource Management Bill is scheduled for introduction to the House in December 1989 and its date of enactment is scheduled for June 1990.

Jan 1, 1990

By Morris A. E

The thermodynamically-based pyrometallurgical simulation software STEPSOL (Version 3.0) provides for the modelling of activities using the Interaction Parameter Model, the Regular Solution Model, the Sub-Regular Three Suffix Margules Model, the Sub-Regular Four Suffix Margules Model and various simpler polynomial models. These are briefly reviewed, along with the major sources of data available in the literature, and the implementation of the models in the program.

Jan 1, 1991

By Whiteley M, Robinson T, Vernon B

The Western Australian gold industry has approximately 100 operating plants, mainly CIP/CIL. The nature of the State's rapidly expanding gold industry gave rise to concerns over management of the cyanide hazard, in that most plants are remote from major population centres, have a workforce with a high turn over and use highly saline process water. Approximately 4,500 workers in the industry have the potential to be exposed to cyanide in the course of their normal work.This paper outlines the risk management strategy developed by Government and industry to monitor atmospheric HCN gas in the work environment and the role of continuing education and training along with regular site inspections by Department of Mines Inspectors.

Jan 1, 1990

By I Warren, M P. Simpson

Adularia-sericite epithermal ore deposits have well-documented alteration mineral zonation patterns with distinctive geochemical signatures. Proper use of whole-rock geochemistry can provide useful vectors for exploration and can enhance efforts to characterise and quantify the mineralogy and intensity of hydrothermal alteration.   Analyses of Au and Ag provide the most direct vectors to orebodies, and pathfinder elements such as As, Sb, Hg, Zn, Pb and Se are similarly zoned around at least some orebodies. However, the minerals that contain these elements occur almost exclusively in veins, and therefore identifying geochemical vectors related to wallrock alteration that is zoned outward from orebodies is crucial for effective exploration.   Distal alteration zones contain quartz-illite-chlorite-carbonate-pyrite, whereas samples proximal to veins contain quartz-adularia-pyrite, with lesser though variable illite-chlorite-carbonate. Therefore, adularia-sericite epithermal ore deposits show K alteration in their cores. The resulting K-metasomatism can be evaluated in several ways. Areas that have been most intensely altered are commonly characterised by highest K contents, but these results can be complicated by variations in rock type across the prospective area. Potassium mass balance results provide a robust and rigorous assessment of K-metasomatism, however, knowledge about the composition of fresh rocks and correct identification of fresh precursor compositions of altered rocks are required. Three alteration indices provide effective evaluation of K-metasomatism: 1.   the K number, which is the ratio K/(2Ca+K+Na) (molar); 2.   Barrie values [(K2O * 100) / Sr]; and 3.   the Rb/Sr ratio. In most places these provide similar vectors, although K numbers can be complicated by the appearance of hydrothermal calcite and/or albite.   Plots of K/Al vs (2 Ca + K + Na)/Al (molar) allow estimation of the intensity of K-metasomatism and its mineralogical products, thereby complementing traditional XRD and petrographic studies of alteration minerals.

Jan 1, 2005

By D E. Ralph, D-J Kim, G-J Ahn, Y-H Rhee

The amount of discarded dry batteries are presently found to be increasing globally and waste cathode active materials of the lithium ion battery industry are among them. Hydrometallurgical operations are being applied to recover the valuable metals from these waste batteries. To find an economic and environmentally friendly process, the bioleaching process was applied in the present investigation for recovery of valuable metals. Its principle is the microbial production of sulfuric acid and simultaneous leaching of metals. Bioleaching of spent lithium ion secondary batteries, containing LiCoO2, has been studied in this investigation. A new method for recovery of cobalt, potentially the basis of an economic and environmentally friendly process was examined. The present study has been carried out using chemolithotrophic and acidophilic bacteria Acidithiobacillus ferrooxidans, which utilises elemental sulfur and ferrous ion as the energy source to dissolve metals from spent batteries. Bio-dissolution of cobalt was found to be faster than lithium. The effect of initial Fe(II) concentration, initial pH and solid/liquid (w/v) ratio were studied in detail. Higher Fe(II) concentration showed a decrease in dissolution due to co-precipitation of Fe(III) with the metals in the residues. Similarly, at higher initial pH values and higher solid/liquid ratio (w/v) metal dissolution was found to be inhibited. The optimised conditions for bio-dissolution were solid/liquid (w/v) ratio û 10 g/L, initial Fe(II) concentration û 3 g/L, elemental sulfur û one per cent (w/v) and initial pH û 2.5. In the optimised conditions, cobalt dissolution was observed to be about 60 per cent, whereas that of lithium was ten per cent after 20 days. A first order kinetic model was derived to study the rate of dissolution of both the metals.

Jan 1, 2006