Search Documents

By N Phillips

Fosterville gold mine recently celebrated production of its one millionth ounce of gold based firmly within a history of refractory sulfide gold mining. Compared with other Victorian gold mines, the disseminated nature of the sulfide gold is a deposit style with low estimation variance combined with established processes to accurately delineate the controlling structures. The systems in place had been established and have worked effectively for the majority of the one million produced ounces.By the end of 2014, diamond drill campaigns targeting the lower Phoenix orebody at depths of 800 m below surface began showing a change to the nature of the gold within the deposit. Coarse visible gold within 0.5–2 m thick quartz carbonate veins were being intersected with regularity showing the emergence of a different zone of gold mineralisation.Data about the new and exciting discovery couldn’t be gathered fast enough, however, established systems and processes throughout the geology and processing departments were not developed to handle a coarse gold environment. Change would be commensurate with the size and scale of the discovery, and new learnings would need to be implemented quickly to keep in front of a mining schedule that was focused on producing tonnes due to the dropping grades of the sulfide ore.Gold assays being returned were showing that the gold nature was different to those of other Victorian deposits. Comparative to the highly nuggety nature of gold found in other Victorian goldfields, the fine grained gold accumulations were dispersed in relatively consistent narrow linear trends grading consistently into the hundreds of grams per tonne. New drill intersections were being returned by the day and research to find developed orebodies that had published information into how to handle such a rapid change yielded few examples.The challenge was to review and set new standards with regards to handling an orebody that transitioned the very nature of the gold being mined. This involved reviewing all steps in the estimation process including data capture and quality control and quality assurance through to mineral liberation through the mill. Difficulties also involved finding analogous orebodies that consisted of both free milling and refractory ores that were dealing with drill assays that were measured as percentages of gold.CITATION:Phillips, N, 2017. Fosterville gold mine – breaking the mould for Victorian gold, in Proceedings Tenth International Mining Geology Conference 2017, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

The rush for alternate iron-units in the last few years spurred a true outbreak of new alternate iron units projects many of them incorporating new process in what can be classified as the.most fruitful and innovative technology outburst, in the steel industry, in decades In a recent paper we focused on what would be, in our opinion, the ultimate targets of the use of alternate iron-units by mini-mills: 1. to improve quality, 2. to reduce cost, 3. to increase plant productivity, and 4. to improve `supplyability'. With these objectives in mind liquid hot-metal, among all possible scrap substitutes, has been proven to be by far the best. This conclusion stems from many different authors who have reviewed the `value in use' of hot-metal against other alternate iron units and measured its impact on steel-shop productivity and cost (Figure 1).

Jan 1, 1999

By J C. Volkwein, A D. A Hansen, E Sarver, C Barrett

Ensuring that diesel particulate matter (DPM) levels in underground metal and non-metal mines are maintained below statutory limits is an essential requirement of mine ventilation systems. However, despite the cost of providing ventilation, air ventilation rates are usually based upon models, assumptions, or measurements integrated over long durations rather than actual need. Real-time measurement of DPM, interpreted in terms of mine activity schedules, can offer better ventilation management to keep DPM within regulated levels while controlling costs. This work presents data from three demonstration sites with in-mine applications of an environmental particulate sensor that measured black carbon (BC) as a surrogate for DPM.Aethalometers are a class of environmental monitors that measure the light absorbance of aerosol particles at several optical wavelengths. A model AE33 Aethalometer was operated in three separate mines for periods of two weeks, three months, and seven-plus months, and the data was reported in real time as a concentration of BC. Concentration of aromatic organic compounds, which can indicate other forms of combustion, was also reported. The data was used to:- measure the relative efficiency of a new scale-model DPM air scrubber- determine if ventilation could be reduced in a shotcrete loading facility without compromising air quality- evaluate diurnal and weekly DPM levels in a large-entry stone mine. Instrument data were displayed locally and stored for later downloading in all cases. In one mine, the instrument was connected to a local controller, and in another it was connected to the mine’s underground network so that DPM data was presented in real time to a display in the mine ventilation engineering office on the surface.The results showed that the air scrubber removes from 82 per cent to 95 per cent of the DPM; that DPM produced during shotcrete loading is only a minor part of overall DPM levels; and that wide variations in DPM levels exist in the limestone operation. The DPM monitor operated continuously for extended periods in these underground environments. The only maintenance required was the routine replacement of filter tape, typically on a two-week schedule. A sample diluter, which is currently being tested, could extend the intervals between filter changes. The real-time data output of the Aethalometer is appropriate for direct integration into ventilation-on-demand control systems.CITATION:Volkwein, J C, Barrett, C, Sarver, E and Hansen, A D A, 2017. Application of an environmental ‘black carbon’ particulate sensor for continuous measurement of DPM in three underground mines, in Proceedings Australian Mine Vent Conference 2017, pp 143–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A G. Mitchell

Stream sediment geochemical analyses were collated from open-file mining company reports and assembled in the REGCHEM computerised database at the Institute of Geological and Nuclear Sciences Limited. The database operates on an IBM-compatible PC microcomputer using an application programmed in dBASE IV and termed GEOEXPL. By August 1992, data for 6383 stream sediment samples from 6335 different sites in the Coromandel Peninsula region (Hauraki Goldfield) were entered, giving a total of 29 292 separate elemental analyses. Preliminary statistical analysis using PROBPLOT on a set of data collected by AMOCO from the Mahakirau-Whangapoua area shows that these data are a complex mix of subpopulations related to mineralisation and different source rock types. Thresholds of 37 ppm copper, 31 ppm lead, 112 ppm zinc, and 2.3 ppm molybdenum, defmed by arithmetic models for the combined data set, separate the individual element sets into 'first order anomalous/lesser anomalous and background' subpopulations as follows: copper five per cent/95 per cent, lead five per cent/95 per cent, zinc one per cent/99 per cent, and molybdenum 15 per cent/85 per cent.

Jan 1, 1992

In this address I look back over the past 40 years of mineral exploration in New Zealand û essentially the period since the Second World War (ie since 1945). It was the period of my personal involvement, and indeed of the personal involvement of a number of you. Luckily it was aperiod of great interest and activity. In the previous 50 years, virtually nothing had happened, and it is kindest to draw a veil over that period. In the very important earlier 40 years (1855 - 1895) the New Zealand gold rush occurred. That must have been a fascinating, rewarding period, which has been thoroughly documented by better historians than myself. I will simply comment firstly that its mineral explorers (gold-prospectors) were very successful indeed, and found most localities of the minerals they sought, in spite of using very different methods from ours of today. Secondly, they were preceeded by one of Maori exploration, which searched for a much restricted list of minerals, but succeeded in finding virtually every locality we know of today. The explorers of both of these early periods were obviously highly successful, but, in the time available, I must restrict myself to the period since 1945. I am currently editing the effective up-dating of Gordon WilliamsÆ 'Economic Geology of New Zealand' (1974). It covers the last 12 years or so. Many of you are contributing to that volume û both as authors and as referees û and I would like to take this opportunity of thanking you all. Although this new volume excludes the energy field, many of us have been involved in it, and I am therefore including energy minerals in this review, as Williams did in 1974.

Jan 1, 1987

The Zeehan field has yielded over 190 000 tons of lead and 26,000,000 oz of silver. Moh of the production took place between the initial discovery of silver-lead ore in 1882 and 1920, and the greatest part was extracted from fissure lodes in the Proterozoic to (?) lower Cambrian rocks. It is demonstrated that the prosperity of the mines relied upon the silver content, which is apparently highest in these beds, particularly where spilitic rocks are associated with them. In contrast, galena occurring in orebodies emplaced in the Gordon Limestone is low in silver.Most of the workings are relatively shallow due in some cases to enrichment related to erosion surfaces.Fault zones within a complex anticlinal structure exposing the Proterozoic to (?) lower Cambrian formations appear to have been major factors in the control of mineralization.

Jan 1, 1968

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

By Wilson A. F

The use of stable isotopic measurements as a technique for elucidating the origin and history of the water in hydrothermal fluids is relatively new. Recept studies have emphasized the importance of meteoric water in the formation of many hydrothermal ore deposits including many epithermal gold-base metal deposits which occur in faulted volcanic terrane. Other vein-type gold ores are believed to have formed from fluids of magmatic or metamorphic origin and exhibit characteristic d18O values. Preliminary oxygen and carbon isotopic data for some important gold deposits of eastern Australia have emphasized the diverse origins of their ore fluids.The Mount Morgan gold-copper orebody is shown to be of the volcanogenic massive sulphide type with ore fluids predominantly of sea water origin. The Charters Towers fissure veins formed during hydrothermal activity associated with intrusion of Lolworth Igneous Complex equivalents. Oxygen isotopic studies of the quartz reefs at Stawell and Gympie have been inconclusive. The ore fluids have a d18O value of about 7 per mil and may be of magmatic or metamorphic derivation.

Jan 1, 1981

The mining industry to the lay mind is one which appears peculiarly dangerous, partly because the accidents which take place are usually of a very tragic nature, and partly because other, industries claim victims more from disease than fromviolence, and their fatal nature is not advertised to the same degree so that in spite of this idea of unusual risk, it is a fact that mining will compare favourably, as regards vital statistics, with nearly all other trades requiring special training.Neverthelessthere are a larger number offatal and serious accidents occurring year by year than one would like to see, and could the deaths which take place by accident be eliminated, it is safe to say that mining would become one of the most healthy of all species of skilled labour. If we examine the accidents appearing yearly in the reports of the Mining Departments of the various colonies, it will be at once admitted that many of them need riot, and in many cases ought not to, have occurred.It is, therefore, the object of tbis essay, to pass under review the ordinary precautions which should be adopted to minimise, as far as possible, the dangerous factors whereby fatalities are brought about.

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By Alvin J. F

Tin in ores containing 0·025 to 1·5 per cent tin can be determined polarographically by the reduction of the chlorostannite ion at the dropping mercury electrode in 2M hydrochloric acid solution containing 15 per cent ammonium chloride. The tin is separated from interfering elements by distillation as the tetrabromide and collected from the distillate by co-precipitation with aluminium hydroxide. The method can detect 0·01 per cent tin in ore.INTRODUCTIONAn iodimetric method, suitable for routine analysis of titrating tin in concentrations down to 1 per cent, has been available for some years (Low, Weinig, and Schoder, 1939).As concentrations fall below 1 per cent tin, there is increasing difficulty in obtaining a distinct end point due to large amounts of iron and silica normally present after fusion of the ore. Since concentrations of tin down to 0·02 per cent are significant in ore dressing products it was necessary to examine methods to determine such low concentrations, and to adapt these to tin ores containing a wide variety of other minerals.EXPERIMENTALDigestion and separationCassiterite, the principal tin mineral, is refractory but readily attacked by a sodium peroxide flux to yield soluble sodium stannate. In a recognized procedure, a sample of ore is mixed with up to 15 g of sodium peroxide in an iron crucible and swirled over the full heat of a Meker burner for 7 min. The fusion is leached with water and acidified.This solution then contains tin, silica, and other soluble...

Jan 1, 1962

Fines and unnecessarily small rock fragments are created by as many as four identifiable breakage mechanisms which operate close to the charged section or sections of the blasthole. The peak blasthole pressure (Pb) should not exceed that value at which the rock starts to fail in compression. Excessive Pb values can be prevented by carefully selecting:1. the composition, density and/or diameter of the charge, and2. the initiation/priming system.The percentage of fines increases with:1. increases in the charge diameter:blasthole diameter ratio, burden distance, blasthole diameter, effective sub-drilling and size of blast, and2. decreases in blasthole spacing, stemming height and the length:width ratio of the blast block.Decked charges tend to reduce the percentage of fines.Excessive fragmentation is more evident in buffer blasting and sinking cut shots than in blasts fired to a clean free face. Initiation sequences which give effective burdens considerably less than drilled burdens encourage the minimization of fines, as does an inter-row delay time which promotes good progressive relief of burden.The wastage of explosive energy in creating fines is most pronounced where fully-coupled, energetic charges are fired in weak and/or highly porous rocks. This is especially so where forward movement of the strata is impeded by buffer rock, excessive burden distances and/or inadequate inter-row delay times.

Jan 1, 1979

The presence of undetonated explosives in a rock face after firing constitutes a hazard which can result in a fatal or serious accident if undetected before drilling commences.Most accidents caused by drilling into explosives are the result of failure to examine the working face properly and lack of care in subsequent drilling operations; it is not always realized that explosive may be left in the butts of holes or may be driven into cracks or crevices in the rock.Obviously the best means of preventing accidents of this nature is to adopt methods of drilling, charging and firing which will reduce the hazard to a minimum.There are three ways in which undetonated explosives may be left in the rock face, namely:1. Misfires.2. Cut-off shots.3. Incomplete detonation or failure of the charge to propagate throughout.MisfiresNo attempt will be made in this paper to deal fully with the question of the prevention of misfires, as apart from the fact that most of the preventive methods are well known, it is believed that if the miner receives his explosives and means of initiation in good order, and proper care is taken in their use, the failure of a charge to fire will be a rare occurrence. The provision of central fuse capping stations on mines has gone a long way towards the elimination of misfires caused by the mishandling of safety fuse anddetonators.

Jan 1, 1956

Interest in those physical properties of minerals which might be used to good effect in prospecting is not new. Early in the nineteenth century attempts were made in th'e Cornish mines to measure the natural electric potentials set up by chemical changes proceeding in the lodes. The distortion of the earth's magnetic field by bodies of strongly magnetic iron ore received early recognition in Sweden. Treasure-finders, working on the principle of electrical induction, appear to have been invented about eighty years ago, though were probably not then applied to mineral exploration. By the end of the nineteenth century Eotvos, a Hungarian physicist, had constructed a highly sensitive type of torsion balance capable of measuring the minute distortions in the earth's field of gravitation resulting from variations in the density of the materials composing the crust. During the first decade of this century he demonstrated its value in tracing rock-salt deposits in virtue of their low density compared with the surrounding rocks. Geophysical prospecting began to be recognised as having a very definite value and its development gathered momentum. Its great expansion took place after the 1914-18 war, when its value in oil exploration was amply demonstrated, and this expansion has continued to the present time and shows no signs of abating.Divisions of Applied Geophysics.The four main divisions of applied geophysics are electrical, magnetic gravitational and seismic. With the importance of ores of radio-active metals, one might add to these a radio-active division. The first two are more important to the field of mining, but techniques based on gravitational attraction have their uses in particular cases. Seismic methods are not generally suited to the exploration of metallic ores, but have proved of enormous value in the search for petroleum. With vast quantities of oil as the prize, more money has been lavished on the deve10pment and practice of these methods than on all the others put together.Geophysical Prospecting Methods.Geophysical prospecting methods may be used to detect a mineral deposit directly in virtue of differences in the intensity of some physical attribute common to it and the enclosing country rock. Examples of this are the detection of rock-salt by gravity measurements, or of iron ore by magnetic methods. Of much wider application, however, is the indireot approach in which the aim is to determine, by geophysical means, the geological structures controlling the disposition of mineral deposits. These structures may be partly known from geological work, in which case geophysical methods are useful adjuncts. Where, because of an 'unbroken cover of overburden, no useful geological information presents itself, scout drilling or geophysical prospecting are the only alternatives. Overburden is here intended to mean any covering material not, involved in the structures controlling the mineral deposits. Prospecting for petroleum amounts to the detecting of favourable reservoir structures, and as the chief types of such are the same the world over...

Jan 1, 1950

This Department handles all ores prior to blast-furnacing, the object of the operations being to mix the lead-bearing material with fiuxes, eliminate sulphur from the mixture, and produce a homogeneous sintered product which is chemically and physically suitable for treatment in the blast furnaces.During the financial year ended the 30th June, 1937, the tonnage of charge treated was 458,960 tons, containing some 183,470 tons of lead and 8,504,000 oz. of silver.The quantities of the principal components of the charge treated were as follow:-

Jan 1, 1937

By D Vickers, N C. Fowke

The reduction of geological risk for planning of high production longwall faces is essential. Geological and geophysical techniques applied at Huntly West Mine before 1989 were unable to reduce the geological risk to an acceptable level. The success of a trial long-hole directional drilling programme at Huntly West Mine (Fowke et al, 1989) has encouraged the Coal Corporation of New Zealand to use the technology long-term, for seam definition. Initial drilling in 1989 completed a total of 3543 metres, with the longest borehole length being 369 metres (limited by number of rods available). A major re-interpretation of seam structure resulted from the drilling, which was able to fill in seam details between surface exploration boreholes. The undulating thick seam conditions at the mine require a refinement of drilling strategies used overseas. Long-hole directional drilling also displays potential for inseam gas drainage. Gas flows of the order of 1000 L/min were initially indicated in individual boreholes. Other gas parameters of the seam have been studied by Beamish et al (1991), and highlight the significance of the natural gas resource in the Huntly Coalfield.   The continued development of drilling technology will be of major benefit sustainable development, particularly in policy.

Jan 1, 1991

Low displacement fault zones often comprise a mesh of interlinked faults, extensional-shear and purely extensional vein fractures. Hydrothermal mineralisation localised around such structures testifies to their importance as conduits for fluid flow. Mesh structures are most commonly developed in situations approximating bulk pure shear but predominantly simple shear meshes also occur. They appear to develop through the infiltration of pressurised fluids into a heterogeneous rock mass with varying material properties. In some circumstances, mesh formation appears to be a precursor to the development of major through going faults. Mesh formation generally involves hydrofracturing (Pf > s3, at least locally) and the condition Pf ~ s3 to be maintained for the mesh to remain a high permeability conduit, requiring fluid over pressuring at other than shallow depths in extensional-transtensional regimes. The volumetric character of earthquake swarm activity appears to result from the passage of hydrothermal fluids through mesh structures, representing a form of distributed fault-valve action along suprahydrostatic hydraulic gradients arising from magmatic intrusion, compaction overpressuring, metamorphic dewatering, etc. Fluid redistribution in the crust is influenced by maximum hydraulic gradient (not necessarily vertical), by existing permeability anisotropy arising from bedding and other forms of crustal layering, and by structural permeability developed under the prevailing stress field. Strong directional permeability develops in the s2 direction, parallel to fault-fracture intersections within the mesh and orthogonal to fault slip vectors. In particular tectonic settings, stress-controlled permeability allows strongly focused flow through fault-fracture meshes with high potential for mineralisation. Favoured localities for mesh development include short-lived link structures along large-displacement fault zones such as dilational jogs, lateral ramps, and transfer faults.

Jan 1, 1995

By M Passmore, N Poznik

Olympic Dam is a world-class deposit and is unquestionably one of the most geologically, structurally and texturally complex orebodies in the world. As development advances into the Southern Mine Area (SMA) the geological understanding is rapidly evolving as underground drill rigs are prioritised to provide the additional data necessary to convert Indicated and Inferred Resources into Measured Resources. The SMA represents approximately 70 per cent of Olympic Dam’s total resource and is significantly more complex when compared to the Northern Mine Area with respect to the diverse nature and origin of lithotypes, rock mass characteristics and the extent of major structures controlling primary mineralisation trends.Recent mine development into the central SMA has been impacted by a major structural gouge zone. Sound geological interpretation allowed mine geologists to successfully integrate their local understanding of the distribution of lithotypes with critical geotechnical data, chiefly rock quality designation (RQD), to delineate and better predict this major structural gouge zone. As a direct result, development rates improved whilst also increasing awareness for the importance of sound geological interpretation utilising all available data. In order to maximise predictability across all systems in place through the mining geology value chain, the integration of geological and geotechnical data in a geotechnical RQD block model provides an additional tool to assist in preventative solutions for complex problems to achieve a proactive mining environment.This paper details the methods used to build the RQD block model, the geostatistical estimation parameters, 3D geotechnical domain wireframes, challenges regarding legacy approaches, and collection of geotechnical information and incorporating/linking geotechnical data with geological features, including the use of grade and lithotype domains. Although the geotechnical block model proved difficult and complex to construct, the resultant product has seen successful integration of geological and geotechnical data into mine planning providing higher resolution of critical parameters for local mining areas.CITATION:Clark, J M, Passmore, M and Poznik, N, 2017. Olympic Dam rock quality designation model – an integrated approach, in Proceedings Tenth International Mining Geology Conference 2017, pp 27–36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R L. Brathwaite

As part of an investigation of the deep structure of the Waihi Basin, an extensive set of resistivity measurements was recently collected by DSIR Geology & Geophysics. The objective of this work is to map deep resistivity changes throughout the Waihi area in order to contribute to a better understanding of the regional geophysical structure. This research is also aimed at improving techniques for locating 'deposits of epithermal mineral resources, and helping to establish their origin and genetic relationship to fossil geothermal systems.   The results indicate that the basin south of Waihi is underlain by an extensive layer of low resistivity, modelled as a 5ohm-m layer several hundred metres thick. Lake sediments (mudstones), as exposed in the south western part of the basin, near Waitawheta, are the most likely source of this low resistivity layer, although hydrothermally altered clays and/or elevated temperatures are other possible causes. Strong northeast trending anisotropy is also observed, implying structural links from Waitawheta through to Golden Valley. The observed resistivity pattern is consistent with a æburied calderaÆ or æfaulted depressionÆ structural model for the basin, as inferred from gravity and magnetic data.

Jan 1, 1991

By Warren L. J

The effectiveness of shear-flocculation as a method for upgrading simple mixtures of ultrafine (1-11 \lm) scheelite and garnet was evaluated. Statistical methods were used in the design and analysis of the main test program.The stirrer speed, stirring time, and initial weight ratio were all found to have significant effects on both the recovery and grade of the floes produced. The particle sizes also had an effect on the final grade. There were several important interactions between factors which also affected the results. Optimum conditions for shear-flocculation were established, and under these conditions about 80 per cent of the scheelite could be recovered at a grade which depended on the composition of the starting mixture. Starting with mixtures containing 10 and 50 per cent scheelite, the best final grades were between 20 and 50 per cent and between 70 and 90 per cent respectively, the actual value depending on the particular combination of particle sizes.

Jan 1, 1977