Search Documents

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

By G T. Hefter, P Singh

Sulphur dioxide oxidation is an attractive alternative anodic reaction to the evolution of oxygen in copper electrowinning. Accordingly, the electrochemical oxidation of SO2 in aqueous 1.0 x 10-1 mol/L NaClO4 has been studied at pH 2.3 using platinum and glassy carbon electrodes. On the platinum electrode SO2 oxidation occurred on the forward scan at 0.96 V and on the reverse scan at 0.63 V. For GC, a single SO2 oxidation peak occurred at 1.40 V on the forward scan. SO2 oxidation on both electrode substrates was hampered by oxide layer formation. The electrode could be reactivated however, by oxide layer reduction. Although reactivation was most successful for platinum, SO2 oxidation on platinum is quite complex, with this evidenced by the reverse scan anodic peak. Glassy carbon shows simpler behaviour and thus, is the preferred substrate for SO2 oxidation.

Jan 1, 1998

By S Mitra, D O’Dea, N Barrett, S, T Honey, M M. Hoque

The steel industry is currently exploring hydrogen-enriched blast furnace operations as a means to reduce the greenhouse gas emissions. However, there is a need to investigate the gas permeability behaviour of mixed burdens comprising of lump and sinter as the current knowledge regarding their behaviour is limited, particularly with regards to hydrogen enrichment. In the present study, a series of interrupted softening and melting (S&M) under load tests were carried out in a hydrogen rich gas environment (~15 per cent) in the temperature range from 1000 to 1300°C by placing different types of ferrous ore layer including Newman Blend Lump (NBLL), sinter and sinter-NBLL mixed burden in between two coke layers. X-ray computed tomography (CT) was then used to scan the interrupted test samples. Scanned images were first analysed using an image processing workflow implemented in ImageJ and the material simulator GeoDict (v2022) to segment different phases such as coke, ferrous and void based on their grey scale values. A quantitative analysis was then performed on the segmented images to estimate the phase volume fraction as well as bed permeability. Bed void fraction thus obtained agreed well with the bed contraction data obtained from the S&M test. It was further noted that both ferrous layer void fraction and bed permeability decreased linearly with increasing temperature for all ore samples. The mixed burden voidage changed in a similar fashion to the sinter, demonstrating a high temperature interaction between the two materials

Sep 18, 2023

By F Shi, W Valery

WMC Fertilizers (WMCF) operates a Beneficiation Plant at Phosphate Hill in Queensland, Australia. The plant consists of two-stages of crushing, followed by a wet scrubbing and desliming circuit. Ore is then fed to a tertiary crusher and a milling/classification circuit, with the final product going to a swing-lift thickener and storage tanks. From the slurry storage tanks, the phosphate rock is fed to a horizontal belt filters which dewater the phosphate rock ahead of a hemi-hydrate phosphoric acid plant. The water soluble recovery of phosphate in the phosphoric acid plant is dependent on the moisture content in the filter cake, as this governs the wash water addition to the hemi-hydrate filters. Since commencement of operation, the moisture content of the filter cake fed to the phosphoric acid plant has been higher than design reducing the phosphoric acid plant recovery and at times reducing the throughput through the phosphoric acid plant. The moisture content in the filter cake can be decreased by reducing the generation of fines in the milling and classification circuit (classified as û38 micron material). This paper identifies the causes of fines generation in the Phosphate Hill beneficiation plant. It discusses the options that were assessed to minimise fines generation, and outlines the results to date of circuit changes undertaken at Phosphate Hill.

Jan 1, 2003

Battle Mountain Gold Company's Paj ingo Mine is the first gold mine developed by the Company in Australia. The Mine located in northern Queensland commenced operations in September 1987. The high grade epithermal orebody is selectively mined and processed through a conventional carbon in leach/carbon in pulp (CIL/CIP) plant at a rate of 200000 tonnes per annum. In 1988 it produced 61000 oz gold and 152000 oz silver. Inadequate preoperational development of non technical management and organisational functions often leads to inefficiencies that last well into the operation. The Pajingo experience in this regard is oaTple ented by those from a number of other recently commissioned small operations. A checklist is discussed to assist any future preoperational group in focussing their attention into areas that seem to be of secondary importance at the time but often have a significant impact on overall management efficiency later.

Jan 1, 1989

By D Miller, M Dowling, R Domotor

"This paper is focused on blasting activities undertaken as part of the Pacific Highway Upgrade – Tintenbar to Ewingsdale – project (T2E). This is a ‘priority 1’ Pacific Highway road construction project in New South Wales (NSW), to be completed by mid-2015 (weather permitting). T2E will provide approximately 17 km of dual carriageway road starting at the northern end of the Ballina bypass and extending to the Ewingsdale interchange, and will complete the existing dual carriageway road between Ballina and the NSW/Queensland border.Roads and Maritime Services (RMS) (formerly the Roads and Traffic Authority) is delivering the project on behalf of the NSW state and federal governments. In October 2011, RMS awarded a contract to Baulderstone Pty Ltd (now Lend Lease Engineering Pty Ltd – Lend Lease) to design and construct T2E. One of the key elements in this project is the St Helena Tunnel.In order to avoid the steep grades of St Helena Hill, eliminate a well-known accident black spot and maintain the aesthetics of the Byron hinterland escarpment, RMS and Lend Lease prepared designs to construct a 434 m long dual carriageway tunnel, 46 m below the ridge line of St Helena Hill. Lend Lease elected, where geotechnical conditions permitted, to use drill and blast methods to excavate the full tunnel profile, instead of traditional mechanical excavation techniques.Since all blasting locations (both inside and outside the tunnel) were in close proximity to nearby residents, the NSW Department of Planning and Infrastructure imposed strict air blast overpressure (airblast), ground vibration (vibration) limits and limited working hours. Both RMS and Lend Lease recognised that these restrictions meant that nearby residents may be exposed to blasting activities for longer than was necessary. As a result, after close consultation and agreement with the nearby residents, RMS applied successfully to the NSW Department of Planning to increase the airblast and vibration limits, as well as the working hours.Working under these new conditions, Lend Lease employed a range of best practice drill and blast technologies provided by both Orica Australia Pty Ltd and Atlas Copco Mining and Rock Excavation to improve the safety and efficiency of blasting activities and to minimise the potential negative impacts of the blasting works on affected residents. These technologies included: the use of a continuous environmental monitoring system to record the results of the blast events and provide quick and easy reporting to key stakeholders to address RMS specification requirements electronic detonators to enable accurate hole detonation timing for vibration compliance and to give project engineers the flexibility and precision to alter each design to suit the geological profile of each face the use of two software programs and advanced drill rigs to enable the efficient design of blasts, electronic transfer of designs to the drill rigs, as well as in-hole monitoring and recording of drilling performance the use of a specialised bulk emulsion system to deliver fully coupled bulk explosives into face blastholes to maximise fragmentation, and decoupled bulk explosives into perimeter blastholes, to reduce overbreak and deliver a cleaner profile.By taking a progressive approach towards the environmental restrictions and the work hours imposed, as well as utilising best practice blasting techniques, RMS and Lend Lease were able to blast with confidence and achieve their production deadlines and reduce the total cost of the project.Most importantly, RMS and Lend Lease were able to meet their environmental obligations and work constructively with the nearby residents to ensure that the blasting was undertaken as safely and efficiently as possible without delay or negative impact.CITATION:Dowling, M, Domotor, R and Miller, D, 2014. Improving excavation efficiency at the St Helena Tunnel using best practice drill and blast techniques, in Proceedings 15"

Sep 17, 2014

Drilling underground can be a hazardous undertaking in many circumstances. Raiseboring and boxhole boring underground could form an integral part of the block caving production methodology and getting the right mix of technical capability, ergonomics and economical viability has been the goal of many machine manufacturers. With the introduction of the Terratec Universal Boring Machine concept, flexibility of raiseboring, downreaming and boxholing has been enhanced by the introduction of a single machine that will perform all three processes. In addition to its technical flexibility, additional safety features have been introduced that will eliminate many sources of injury by mechanising most of the operational procedures. Together with the one-man remote operation, this machine design addresses and solves many of the safety issues. This paper outlines the machine concept, details its safety features and shows the techno-economic advantages for use in the block caving environment. Block caving is a distinct caving method applied mostly to large massive orebodies because of the inherent low costs and high production capabilities. Areas of sufficient size are mined by undercutting so that the mass above will cave naturally. Extraction of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling (Figure 1).

Jan 1, 2000

Geological modelling is a crucial preparatory stage to most facets of the mine planning of an orebody. The process of modelling involves skilled geological interpretation. Recent innovations in computer software and graphics hardware provide many tools which can be used to dramatically improve on manual methods of interpreting orebody data. Geological interpretation can be carried out quickly to produce accurate block models for many orebody attributes, such as grades, and these models can be easily updated locally as exploration and mine development data become available. The speed of the modelling process coupled with the mass storage capabilities of the computer now allows geologists to optimise the geological model or carry more than one model through to the mine planning phase.

Jan 1, 1987

By C Torrisi, J Andreatidis, M Duffy

BHPÆs Cannington process plant was commissioned in October 1997. The Cannington ore contains high grades of silver, lead and zinc but also contains high levels of fluorine which must be removed to produce a marketable concentrate. As a consequence the plant is more complex than the typical base metal concentrator. Some of the features of the Cannington operation include a single stage autogenous mill, multiple stages of flotation cleaning, two leach circuits, pressure filtration and a paste fill plant. The start-up and achievement of design performance for new lead/zinc operations has traditionally taken much longer than for gold or copper operation and is littered with many tales of woe with feasibility targets often not achieved (Agarwal, Brown and Katrak, 1984; Bulatovic and Wyslouzil, 1999; Leung, Andreatidis, Woodall and Alford, 1996; Sherman, 1999; Ward, 1998).

Jan 1, 2000

This case study reviews the Charters Towers vein systems for potential open-pittable bulk tonnage resources in' stockworks, horsetails or multiple vein systems. The review summarises district evaluation undertaken over the last 18. months before specific drill evaluations.Historical mining from Charters Towers includes in excess of six million ounces at head grades of one ounce per ton. A review and structural studies show most veins as simple, tight systems without significant horsetails or multiple sheeted systems. In addition the normal gold content of the pyritic selvages ('formation') is low and disseminated gold is virtually absent. Shoots are structurally controlled on vein/vein and vein/contact intersections. Historically high production vein systems are hosted by .,.t o of the younger granodiorite phases.Geometrically most veins dip shallowly (from 45¦ to as low as 200) in a north or easterly quadrant. Flat dips permit open cut exposure of considerable vein area at a favourable stripping ratio.

Jan 1, 1986

By J Durbin

To effectively plan for closure, we must have an end-point in mind. To undertake meaningful rehabilitation, a post-mine land use (or uses) must be known. However, it is becoming more apparent that the end-point or “goal-posts” are shifting - and may continue to do so throughout the life of a mine. As well as being safe, stable and not causing environmental harm, post-mine land uses should always be sustainable, achievable within the given land capability, and they should involve stakeholders in their design and development.The majority of mines in Australia, and around the World, were historically expected to return disturbed land to either native ecosystem or agriculture/forestry practices. However, examples of highly successful final land uses suggest that today’s focus on closure includes not only minimising future liability and impact but also – and importantly – a move towards the creation of economic opportunity (Murphy and Heyes, 2016).CITATION:Durbin, J, 2018. Planning for (not so) final land use, in Proceedings Life-of-Mine 2018, pp 110–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Z Terzic, M Schult, D Chu, S Macklin

The East West Link road tunnels are proposed to provide a connection between the CityLink toll road and the Eastern Freeway north of the Melbourne CBD. The alignment passes from Moonee Ponds valley beneath the Upfield Line railway cutting, Royal Park, the historic Melbourne Cemetery and beneath Alexander Parade rising to an eastern portal at Hoddle Street. The western (Royal Park) part of the alignment passes through the folded and faulted Silurian Melbourne Formation, which has been subjected to deep weathering since the Triassic.The Melbourne Formation in the Royal Park area is mainly characterised by interbedded sequences of siltstone and fine-grained sandstone. The beds are often graded and a clear boundary between the siltstone and fine-grained sandstone rock can be difficult to distinguish. Variation in lithology and the presence of structural geological features such as folds and faults have resulted in an irregular weathering profile within the Silurian rock; nonetheless the formation typically becomes less weathered with depth.Due to difficulties in obtaining reliable laboratory strength and stiffness relationships with weathering grade, in situ testing methods such as downhole shear wave velocity and high-quality pressuremeter testing are a useful aid to assessing appropriate geotechnical parameters for design.This paper presents an analysis of the variation in shear modulus of the Melbourne Formation, determined at small-strain (from downhole seismic data) and at ‘engineering scale’ strain (from pressuremeter tests) for extremely weathered (XW), highly weathered (HW) and moderately weathered (MW) rock. Estimates of small strain shear modulus (Go) obtained a range between 400 to 3400 MPa for these weathering grades. By comparison against the pressuremeter test data, reduction factors to be applied to these Go values to estimate shear moduli at engineering strain levels typically range between 0.10 and 0.35.The downhole geophysics undertaken in the Royal Park boreholes also suggests that there is an inversion in velocity between approximately 15 and 27?m depth below the top of the formation. This is thought to be related to the effects deep Plio-Pleistocene weathering, iron cementation of joints and increasing frequency of ‘non-healed’ joints in the transition from MW to slightly weathered (SW) rock.CITATION:Macklin, S, Schult, M, Terzic, Z and Chu, D, 2014. Strain-dependent stiffness of the weathered Melbourne Formation, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 179–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S Udayakumar, S Biswal, N Sarmadi, V Sahajwalla, F Pahlevani

Recent times have witnessed a notable momentum in the interest surrounding technology dedicated to harnessing waste as valuable resources, prompted by the mounting challenges posed by waste accumulation and the swift depletion of natural resources. The carbon dissolution process within a molten iron bath stands as a pivotal reaction within the metal processing sector. The current study explores the utilisation of waste graphite electrodes (WGE) (obtained after being utilised in an electric arc furnace) as a secondary resource of carbon for dissolution into liquid iron. Experimental investigations were carried out at 1550°C using the sessile drop approach. High purity iron powder was used and the carbonaceous substrates were prepared from the ground WGE. The carbon pickup was determined using a suitable carbon analyser. Furthermore, an examination of the interfacial area between the molten iron and the WGE substrate was conducted beneath the metallic droplet, which effectively represents the iron/carbon interface. This interfacial analysis was carried out on two different samples obtained after a varying period of heat treatments at 1550°C. The interface layer was investigated using scanning electron microscopy (SEM) in conjunction with energy-dispersive X-ray spectroscopy (EDS).

Jun 19, 2024

By A K. B Chigwada

Mining organisations grapple with the same problems year after year, wasting incredible amounts of time and money. According to estimates from the International Labour Organization (ILO), over one million work-related deaths occur annually, and hundreds of millions of workers suffer from workplace accidents and occupational exposure to hazardous substances worldwide. Many accident reports cite human failure as a primary cause (Busse and Johnson, 1998). The workers at the Bhopal chemical plant pumped methyl isocyanate into a leaking tank (Morehouse and Subramaniam, 1986). On 3 December 1984, more than 40 tons of methyl isocyanate gas leaked from a pesticide plant in Bhopal, India, immediately killing at least 3800 people and causing significant morbidity and premature death for many thousands more. The company involved in what became the worst industrial accident in history immediately tried to dissociate itself from legal responsibility (Broughton, 2005). Australia is not spared from safety problems either (Lucas, 2022). The ILO Convention 176 (1995) as a response provides that national law should inter alia provide for the supervision of safety and health in mines; the inspection of mines by designated inspectors of the competent authority; the procedures for reporting and investigating of fatal and serious accidents; the compilation and publication of statistics on accidents, occupational diseases and dangerous occurrences; the competent authority to suspend or restrict mining activities on safety and health grounds until conditions giving rise to the suspension are addressed; and worker consultation on matters related to safety and health in mines. This has assisted in getting enough data to define the magnitude of the problem to the mining sector.

Apr 16, 2024

By A Fern, A Hawkes, o, T Vincent

The modern workplace has changed dramatically in recent years with an increased emphasis on the psychological well-being of employees. While adhering to a certain standard of psychosocial safety at work is now not only a moral, but legal obligation in Australia, it begs the question: how can organisations begin to ensure psychosocial safety? A positive psychosocial safety climate is one where employees feel they are psychologically safe, feel supported in their work and are not exposed to work-related stressors that can negatively affect their mental health. Such a climate can help boost productivity and create a more positive working environment. This presentation will provide a twopronged approach to understanding and managing psychosocial safety: pairing a traditional risk assessment with climate measurement. Risk assessments can provide several benefits, including identifying and characterising work-related hazards, identifying the nature and severity of the risks to employees and prioritising necessary interventions for reducing or preventing psychosocial harm in the workplace. However, these assessments can have certain limitations, especially when it comes to capturing some of the less obvious causes of psychosocial harm. Climate measurement can provide valuable insights into employees’ perceptions of the work environment, identify areas of concern that may not have been identified in the risk assessment and help to guide organisational changes that will enhance employees’ psychosocial well-being over time. It will also be argued that climate should be assessed from a broad perspective exploring general, physical, social and psychological aspects of safety climate. This presentation will explore why conducting risk assessments in conjunction with detailed climate measurements is integral to protecting the psychosocial safety of employees in the workplace and demonstrate why employers should view the two approaches as complementary and interconnected. Best practice recommendations will be provided for the risk assessment, climate measurement and psychosocial interventions

Apr 16, 2024

By Worner H. K

The paper briefly summarises the work of the Titanium Research Section in the Metallurgy Department of the University of Melbourne and mentions the development of a new electrolytic process for titanium production. This process utilises the "hot-spot" cathode technique and titanium carbide anodes. An introduction is given to three further papers on titanium metallurgy to be presented to the Institute.INTRODUCTIONThe unique combination of strength, lightness and corrosion resistance possessed :by titanium and its, alloy has made them of great interest to engineers. However, high cost, difficulties of production and limited knowledge of techniques of application restrict their usage at present almost exclusively to high priority armaments.The cost of the metal is divided between extraction and processing and much research has been carried out to devise new and cheaper methods for winning the metal from its ores. Processing costs will be reduced when production volume increases.Extraction research is proceeding rapidly overseas and Kellogg (1955, p. 72) reports that 'at least seventeen companies in the U.S.A. are interested in titanium production. Of these, two are producing the metal by a modified Kroll process, three are building Kroll plants and the remainder are in various stages of research activity. The Horizons Corporation alone is contemplating electrolytic extraction and is building a pilot plant. Steinberg et aI. (1955, p. 252, p. 332) have reported the early work done by the HorizonsCorporation on electrolysis of potassium fluotitanate and titanium monoxide in fused salt electrolytes. Of these two, the former appears to be the more attractive process.

Jan 1, 1956

Copper entering a lead ,smelter in concentrate or from other sources is recoVered as matte and speiss which contain appreciable quantities of lead. The matte and speiss are usually sold to copper smelters to recover the copper content and also any gold and silver in these products, but the value of the lead is largely lost. Some copper plants pay for portion of the lead content, but regarded as a means of recovering lead it is more costly and less efficient than if the lead were recovered at the lead smelter.Because of the value of this lead loss, the metallurgy of copper recovery has assumed greater importance in recent years owing to the rise on the price of lead.Two processes are in use today to produce matte and speiss, namely the iron matte process and the soda matte process developed by the American Smelting and Refining Co. 1 in D.S.A. The latter process is characterised by a higher copper to lead ratio than the older iron matting process.The following analyses are typical of matte and speiss produced at Broken Hill Associated Smelters, by both processes, although the soda matte process is still in a developmental stage and experience indicates that matte and speiss of lower lead tenor can be produced under favourable conditions.

Jan 1, 1951

By K George

The Dugald River lead-zinc-silver deposit is located approximately 60 km north-west of Cloncurry and 87 km north-east of Mount Isa. The development project is expected to turn operational in 2018. The resource is estimated to contain 61.1 Mt at 12.6 per cent zinc, 1.9 per cent lead and 34 g/t silver, with a projected mine life of 25 years. The evolution from exploration project to development project has presented multiple challenges for the technical team. Understanding and modelling the structural complexity of the deposit has been one of these challenges.Historically fault zones were logged as a lithology, with structural measurements recorded in a separate database table. When underground drill programs and development commenced in late 2012, it was recognised the deposit was more structurally complex than had been modelled. The extensive number of fault zone lithologies in core logging, made it difficult to identify fault trends and model faults in 3D software packages.In 2014, a structural project was conducted to produce a fault model for the deposit. The project highlighted that by logging the faults as a lithology, a shortage of fault characteristics was being recorded. Additionally, structural information could not be filtered to identify different fault sets due to the lack of information available to filter on. One of the major outcomes of the study was to change the methodology for the structural logging of drill core.Faults are now logged in a separate structural log. The structural log collects two types of information: interval data and point data. The interval data represents the damage zone of the fault in the surrounding rock and the point data the plane of movement for the fault. The faults are further characterised by their intensity on a scale of one to five, the type of fault structure (fault breccia, fault vein etc), the minerals present on the fault surface and structural measurements when available.The new data set allows fault data to be filtered based on fault characteristics, making implicit and explicit modelling of the faults more timely and accurate. The data set can be used to produce fault wireframes as single surfaces from the point data or hanging wall and footwall surfaces from the interval data. The logging method and how its applied in fault modelling form the focus of this paper.CITATION:George, K, 2017. A new approach to logging and modelling faults at the Dugald River Pb-Zn-Ag deposit, North West Queensland, in Proceedings Tenth International Mining Geology Conference 2017, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Fuchs

Roadheaders were introduced to mining and tunnelling in the early-1960s. Since this period their main field of application has been for roadway drivages in coal mines and for mineral production, for instance in coal, rocksalt, potash and gypsum mines. Their main field of application in tunnelling is in softer and partly friable rock formations, a suitable area for non-blasting excavation. However, in longer tunnel sections excavators with high ripping forces have replaced roadheaders in many situations. The main arguments against roadheaders have been and still are:a sharp increase in excavation cost with increasing rock strength and increasing abrasivity; and greater risks in conditions which have not been, or could not be, investigated to a sufficient extent. These arguments have, to a great extent, restricted practical roadheader application in production mining and in a lot of æstandardÆ tunnel projects. To address these limitations, factors which could make roadheaders attractive for such conditions and could overcome existing technological difficulties have been investigated. Extension of the economic field of application in hard rock was found to be the most important and the most effective step forward.

Jan 1, 2002