Search Documents

The coastline is. an incomparable stretch of sea coast known as Ninety Mile Beach. Two gas pipelines and two oil pipelines carrying hydrocarbons from thb'Bass Strait fields to the markets of Australia cross this beach. They cannot be seen as they are laid in trenching stretch- ing many miles out to sea and the beach was restored to its natural state. Even where the dunes were disturbed, suitable grass was sown thus consolidating the sand and preventing erosion. Ninety Mile Beach is but one of the many key.wildlife and recreational areas that our operations must be concerned with. Others include Westernport and Corner Inlet, but the one discussed in this paper in particular is the platform area of the Bass Strait itself. Never was the old adage "an ounce of prevention is worth a pound of cure" more meaningful than in offshore oil production. All are well aware of some of the events of the past several years that resulted in large and costly oil spills. Far less is known, seen or publicised about the measures and developments that are undertaken to ensure that such events do not occur. We also have well developed plans for response in the event of an emergency situation, which can be initiated with great rapidity. Our responsibility is to ensure that with the best of engineering technology and operating procedures, spills do not occur.

Jan 1, 1971

This paper carries on from an earlier paper 'Cemented fill practice and research at Mount Isa' and reports further on the laboratory programme at Mount Isa to develop a cheap cem- ented fill using Company waste products. The practical economic significance of availability of cheap cementing agents is re- viewed, with the various alternative approaches available The basic approach adopted within this paper is that use of reactive pozzolans such as ground slags to replace a proportion of the Portland cement in the fill can make mining methods employing cemented fill more economic- ally competitive with other mining methods.

Jan 1, 1973

The Callie Underground Gold Mine (Callie) is owned by Newmont Asia Pacific and located 531 km north-west of Alice Springs in the Northern Territory. Historically, stopes have been mined utilising a primary and secondary stoping sequence with cemented aggregate fill and rock fill respectively. Current and near-future mining will employ long hole open stoping with rib pillars and rock fill with a paste fill system approved to allow a higher extraction ratio from mid-2011. The Callie rock mass is of good quality with little or no mining difficulties during development and stoping to a depth of 1140 m below surface. Development is currently occurring at depth of 1360 m below surface. Stress damage previously observed only in secondary stope accesses is now observed in development unaffected by stoping stresses. A change in rock mass properties is being experienced with depth, with more pronounced and frequent joint planes. Also, other structures are intersected more commonly, such as lithological boundaries and fault zones. The 'Callie rock factory' mentality that has persisted for years is challenged. This paper covers an appraisal of the stress and ground condition changes at Callie. The appraisal outlines the mine design criterion that was developed and examines the transition from a low stress environment to one where stress damage is observed. Discussion includes a judgement on the rock mass damage observed in development, the dominant geotechnical factors influencing the change in ground conditions, and if a correlation can be made between the observed rock mass damage with stress through the use of numerical modelling.

Nov 25, 2010

The history of potential large scale development at Stawell in northwestern Victoria dates back to 1914, when Great Boulder Mines Limited, of Kalgoorlie, Western Australia, took up options on some of the major mines in the Stawell Goldfield. Despite this and other attempts by various groups over the next thirty years, mining activity on the field gradually dwindled to the retreatment of old mill tailings.A static price for gold and indifferent drilling results prevented a major effort towards reopening the field until the late 1970's. A renewed exploration effort led to the discovery of sufficient reserves to justify installation of a carbon-in-leach gold treatment plant.

Jan 1, 1984

By Jagger ND

Pressure filters were found to be necessary to produce Elura silver/lead and zinc concentrates at sufficiently low moisture contents for bulk cargo shipment by sea to smelters.The difficulty in obtaining low moistures was due to the fine primary grind, 80% passing 45 microns, and resultant fine concentrates, 97% passing 45 microns.The filtration system was designed to filter up to 90,000 tonnes/year silver/lead concentrates and up to 130,000 tonnes/year zinc concentrates.This paper details the preliminary test work to select Larox automatic pressure filters, and the commissioning and operation of these filters to achieve design criteria for both concentrates. The design criteria for both concentrates have been bettered due to the concentrates being coarser than the design sizing.

Jan 1, 1985

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

By Smith E. L

The Ore Reserve/Exploration System implemented at Mount Isa for M.I.M. Holdings Limited is a comprehensive computer system designed to process assay, geological, structural and survey data input via special purpose logging sheets from daily activities at Isa Mine, Hilton Mine and various Carpentaria Exploration Company prospects. The system performs two basic functions; (1) data acquisition, validation and file maintenance to prepare the data for retrieval, and (2) generation of routine and optional reports. The types of reports available range from masterfile detail printouts and retrieval of data by key items to survey computations, structural analyses, cutoff calculations, statistical analyses and ore reserve calculations by the polygonal, inverse square or moving average techniques. The use of various optional reports available through the system is illustrated by several examples, and planned future development is discussed.

Jan 1, 1973

By Millett R

In January 1989, Western Mining Corporation (WMC) acquired the Perseverance and Rocky's Reward orebodies and associated infrastructure from the Agnew Mining Company (AMC). AMC had closed the operation in August 1986 and it had been on care and maintenance since that time. To return the operation to full production as quickly as possible it was planned to mine the Rocky's Reward orebody by opencut mining and treat this ore whilst the underground Perseverance workings were rehabilitated. Removal of overburden from Rocky's Reward thus commenced immediately with a target of April 1989 for delivery of the first ore to the concentrator. Extensive rehabilitation and upgrading of the concentrator commenced in late January, and continued in stages for an 18 month period. The first stage consisted of overhauling all existing equipment and completing a crusher upgrade commenced by AMC prior to the mine closure. During this period, it was necessary to recruit a workforce and re-establish all the required support structure. In late April the plant commenced commissioning trials on mullock. The first ore was crushed on the 11th May 1989 and concentrate produced the following day. From May 1989 to June 1990 the plant was producing nickel concentrate whilst further upgrading continued. During this period, the flotation capacity was tripled by installation of a bank of eight Wemco 144L flotation cells in rougher-scavenger duties and two 12 metre by 2 metre diameter columns in cleaning duties. The existing vacuum drum filters were replaced by two Larox PF32 pressure filters, eliminating the need for solar drying and allowing the flash drier to be fed direct from the filters. These, along with a major borefield expansion and further work to the crusher increased the nominal plant capacity from 600,000 to 1,000,000 t/yr. The plant achieved the 1,000,000 t/yr rate in April 1990.

Jan 1, 1991

By Jaracz K

At the operation of mine winders in deep shafts considerable oscillations of winding ropes may occur due to elasticity of both wind-ing and balance ropes. The amplitudes of longitudinal oscillations may reach + lm at relatively low frequencies, ranging from 0.5 to 2 c/s. These oscillations may be dangereus for the rope and produce several hazards to the winding installation as a whole. They may cause conside-rable instant accelerations on the pulley and dangerous tensions in ro-pe wires. The excessive acceleration may cause the uncontrolled rope slip on the pulley. Several methods of limitation of these accelera-tions were developed, some of them have been already in control system: of electric drive of the winder. The most simple ones are: a/ limita-tion of the rate of change of acceleration and retardation of the win-der /so called "jerk"/ and b/ the proper selection of regulators of the winder control system to get the optimal control. The trouble in solv-ing the problem of rope oscillations is that the dynamic system of the winder is a nonstationaryone owing to changing distance of conveyance from the pulley. Besides, the system is described by the equations with distributed parameters. The brief discussion of the theory and its practical aspects are enclosed as well.

Jan 1, 1985

By B P. Wrench, M J. Gowan, P J. Chapman

Embankment dams constructed mainly of sand or non-plastic fine soils are susceptible to liquefaction, particularly in high-rainfall, high-seismicity environments where there is sufficient water to saturate the materials and sufficient energy from an earthquake to cause liquefaction. This paper shows the process adopted to review the stability of an existing cross-valley, centreline-raised cyclone tailings sand embankment dam.The study showed that two-dimensional stability analyses did not sufficiently capture the potential for instability, overestimating the depth of the critical failure surface. Instead, three-dimensional modelling was required to provide a reasonable representation. Post-liquefaction stability analyses carried out using the three-dimensional model indicated an adequate factor of safety (FoS). The FoS under seismic conditions was still considered to be a concern based on pseudostatic analyses (but noting the limitations of the analysis method).Earthquake-induced settlements were estimated using an empirical approach based on case history records (Swaisgood, 2003). The post-earthquake event settlement was estimated to be in the order of 600 mm, which is considered to be acceptable for the embankment, taking account of the proposed long-term freeboard of more than 8 m under operating conditions and 2 m under the probable maximum flood condition.CITATION:Chapman, P J, Wrench, B P and Gowan, M J, 2015. Review of static and seismic stability of a cross-valley sand tailings embankment in a high-rainfall, high-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

In the Illawarra District of New South Wales, Mines were traditionally developed from the seabord. The advantages were close access to the working faces and a minimal depth of cover. Travelling times to the working faces have become prohibitive in many cases due to progressive westward development of the mines. As a result, additional vent- ilation shafts were sunk to service existing mines and new mines were established west of the Illawarra escarpment. Mining operations west of the escarpment are now being conducted at an increasing depth of cover and can be effected by gas related problems such as high seam gas emission rates and gas outbursts.

Jan 1, 1983

By Kennewell G. J

This paper aims to present the evolution of the mining method in the Prince Lyell orebody. Initial strategy and practical experience are detailed as are the reasons for and benefits of changes to the method since 1972 when underground mining began. This section of the paper starts with ten series and concludes with 40 series which was completed in 1989/90.In addition, to update the series of papers written by various authors over the past ten years on Mount Lyell, a review of the experience in the current 50 series lift of mining will be given. As well, the basic planning guidelines are discussed for 60 series - the final lift of the Prince Lyell orebody.

Jan 1, 1992

The celebrations which took place in 1986 to mark South Australia's Jubilee 150 served to focus attention on all aspects of the State's heritage. Until that time the sites and relics of South Aus- tralia's early mines had been generally neglected. Marked by the ruins of enginehouses and littered with the remains of the massive technology of the Industrial Revolution, these sites have now been recognised as containing the threads of a fascinat- ing story. In the early days of settlement the economy of the Colony was based on land and farming. Droughts caused periods of economic depression which were alleviated by chance discoveries of gold, lead, silver, and copper ore. Some of the mines which were opened on the copper deposits were the largest in the world at that time and their names well-known throughout mining circles. Working by hand with primitive equipment, the early miners excavated vast networks of shafts and stopes often extending to great depths: at Moonta- Wallaroo Mines for example workings extended to 860 m below ground. Because of the presence of underground water, mining to these depths would not have been possible without the Cornish pumping engine. Operated by steam power these massive engines and their associated equipment were transported from Cornwall by clipper and delivered to the mines by bullock cart. At this time the engines were at the peak of their devel- opment and, although expensive to import and install, they were highly reliable: the engine oper- ating Hughes pump at Moonta worked continu- ously for sixty years without a major breakdown.

Jan 1, 1987

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

Mining operations have been carried out at Mt. Lyell for the past century. Until the 1970's the location of the mines in relation to the surface topography has enabled the mines to drain their copious inflows of water by gravity. Deeper mining has forced the Company to undertake pumping of increasing inflows of water. A major pumping facility is being established near the base of the known ore reserves with a view to serving the future requirements of the mines. The system has a design capacity of 600 litres per second. Run of mine water will be treated in Vertical Flow Settlers to produce clear water and thickened mud, each of which will be disposed of separately. The clear water will be pumped by six 1000 kW conven- tional centrifugal pumps. The thickened mud will be removed by a Hydraulic Displacement System. The rising mains for both the mud and the clear water are stainless steel cased bore- holes.

Jan 1, 1982

By M E. Rakidjan

The DOZ underground mine at PT Freeport Indonesia is a copper and gold mine in Indonesia with current ore production of 42 000 tpd. Because of the mine expansion into the West DOZ more ventilation raises are needed to create a safe and healthy work place. All ventilation raises that connect the extraction levels to the underlying gallery exhaust drifts at DOZ are now developed using drop raise techniques. This paper describes the improvements undertaken to increase blasting efficiency, to decrease cost and reduce safety risks. This was achieved by using deck loading and presplitting, changing of stemming materials and prevention of excessive raise collar cratering (blow up).

Jan 1, 2005

The BHP Billiton Cannington mine uses sequential flotation to treat a silver, lead and zinc ore supplied from an underground mine. The final products from the process plant are a silver rich lead concentrate and a zinc concentrate. Operational history of plant performance highlighted that the majority of valuable metal losses to final tailing occurred in the -5 ¦m fraction. Research completed on the flotation characteristics of this size fraction in plant feed resulted in the development of a split flotation process to improve the silver and lead mineral recoveries. Construction of a $A 9.5 million brownfield project to install the new split flotation circuit at Cannington was completed in July 2002. The circuit consists of three stages of cyclone classification to recover the ultra fine material to a final cyclone overflow stream, conditioning of this pulp to achieve optimal process conditions, and conventional rougher and three stage cleaner flotation to produce a silver rich lead concentrate. The rougher tail from the new circuit is recombined with the cyclone underflow streams and processed through the original lead-zinc flotation circuit. This paper discusses the circuit design, material properties, material selection for components of the circuit, operational practices and requirements to ensure the circuit succeeded in meeting production targets. The technology is subject of a number of patent applications including international application No PCT/AU02/00400.

Jan 1, 2003

By Terrill JE, Fergusson LJ

In the last decade of precious metal exploration, several important gold discoveries have conclusively demonstrated that epithermal gold deposits formed in what were once active geothermal areas. A significant deposit in this category is the Lihir Island discovery in the Tabar-Ferri volcanic island arc off the coast of New Ireland, Papua New Guinea. Within that arc are the Feni Islands where exploration by Esso PNG Inc. and City Resources Ltd. has been carried out since early 1984. On Ambitle Island in the Feni Group, an epithermal gold prospect located within a young caldera has been tested by diamond drilling. The drillholes intersected a boiling zone at depth beneath acid altered 'cap' rocks. The zone is 30-60 metres thick and comprises hydraulically fractured and mineralised lavas with gold grades of 1-7 g/t. The prospect is still an active geothermal area with current boiling in the zone tested. As on Lihir, the recent epithermal alteration and mineralisation overprints a relict prophyry system. On Ambitle and the adjacent Babase Island several other, cooler exciting gold prospects are currently being tested.

Jan 1, 1987

By N Maistry, A Singh

It is estimated that in less than a decade, high-grade iron ore reserves in South Africa will be depleted, leaving only low-grade ores with a dominant lithology of banded iron formation (BIF) hematite. BIF is a complex ore reserve as it is typically liberated below 1 mm, resulting in high energy costs. However, due to its abundance, its beneficiation potential should be evaluated to maximise recovery at an acceptable product grade. To develop a beneficiation program for BIF hematite, the first step is to determine the effect of two laboratory crushing techniques on mineralogical characteristics, specifically liberation and shape. For this study, the cone crusher and high pressure grinding rolls (HPGR) were used. The Electron MicroProbe Analysis (EMPA) and Mineral Liberation Analyser (MLA) were used to compare the mineralogical characteristics. The liberation characteristics for hematite are similar for both crushing techniques; however, HPGR preferentially liberates quartz. HPGR achieved 8– 12 per cent additional quartz liberation in the greater than 80 per cent and 100 per cent liberation classes respectively and specifically in +75 μm size range. Improved quartz liberation is associated with lower energy requirements for downstream milling and improved separation efficiencies for beneficiation units that operate in this size range. Both samples displayed similar shape characteristics; most particles were elongated smooth and the rest were elongated angular. Good hematite liberation is expected at grinds of 212 μm to 150 μm. Further consideration should be given to throughputs, energy efficiency and downstream equipment selection prior to selecting a crushing technique.

Sep 18, 2023

By D Atheis, S Williams, A Dance, D Taplin

"Resurrected from its former life at the Big Bell operation, the grinding circuit at Evolution Mining’s Edna May operation in Western Australia has many a story to tell. The task of optimising a plant designed for another orebody provides as many challenges as opportunities. Initially faced with a blend of primary and oxide ore, the circuit achieved in excess of 320 t/h until the oxide was depleted, leaving only the much harder primary feed.The 2.0 MW semi-autogenous grinding (SAG) mill and 3.7 MW ball mill were assisted by a 150 kW pebble crusher, but the power limitation of the SAG mill resulted in a drop in throughput. Edna May personnel have been involved in a number of progressive improvements to restore the design capacity of the concentrator and work towards 3 Mt/a or even higher ahead of the gravity and leach recovery circuits.These improvements include: a crush forward configuration of the SAG mill scats partial to full secondary crushing variable speed drive upgrade of the SAG mill lifter and grate design changes ball mill circuit grinding efficiency.This paper summarises the chronology of events that has resulted in significant improvements in throughput by conventional (and in some cases, novel) methods of reconfiguring the existing grinding mills. Lessons learned and hindsight perspectives will be summarised, sharing this educational experience with other operations in a similar situation.CITATION:Dance, A, Atheis, D, Williams, S and Taplin, D, 2014. Grinding circuit improvements at Evolution Mining’s Edna May operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014