Search Documents

By W Dodson

Major ions, d18O and d2H and Carbon-13 concentrations in groundwater from 30 bores near an open pit iron ore mine were used to better understand the chemical evolution of groundwater in the aquifer. The relatively depleted d18O and d2H isotopes of groundwater from various depths suggest that groundwater is recharged from intense rainfall events, with little evaporative effect. The 300 to 500 mg/L increase of major ions relative to that of rainfall is due to evapotranspiration of rainfall during recharge. Geochemical mass balance modelling suggests that the evapotranspiration of rainfall during infiltration through the unsaturated zone varies over six fold from 20 to 130. This coupled with the dissolution of CO2 from the unsaturated zone and partial dissolution of carbonates and gypsum from Tertiary sediments and carbonates from the Wittenoom Formation accounts for the current major ion, d18O and d2H distribution in groundwater. Despite the relatively dissected morphology and steep hydraulic gradient the results of this study highlight the dominance of vertical flow relative to horizontal flow. The study also shows the dominance of rapid recharge by significant rainfall events as an important component of the water budget for east Pilbara aquifers.

Jan 1, 2009

By E Kasai, D Maruoka, Y Konno, T Murakami

The iron ore sintering process produces approximately three per cent of carbon dioxide emission in Japan because a large amount of coke breeze is used as the main agglomeration agent. Therefore, its suppression has been required. A promising method is to replace the coke breeze with biomass char and iron-bearing materials. In this study, the effect of the utilisation of metallic iron with coke or palm kernel shell char (PKS char) as an agglomeration agent on its oxidation behaviour was examined by a series of experiments using a sintering simulator. The use of PKS char leads to a larger decrease in the pressure drop difference of the sintering bed compared to the case using coke. Furthermore, the oxidation rate of metallic iron was larger in the case using PKS char together than that using coke. It was considered that the oxidation of metallic iron was promoted because the bed-temperature increased at a faster rate and achieved a higher temperature.

Nov 8, 2021

By K Brand, M J. Ind, M Rynhoud

Water management at a tailings storage facility (TSF) presents one of the major risks to the safe performance of the facility. International and domestic dam safety guidelines assess a dam’s hazard category based on the consequences of a dam failure and the subsequent downstream damage to the environment and communities.Often a rigorous risk assessment is undertaken during the design stages to identify and control hazards associated with water management through life-of-mine (LOM) phases. However, as experienced during the recent downturn in commodity prices, early closure of a mine can occur rapidly and unexpectedly. Although guidelines such as the Australian National Committee on Large Dams Incorporated (ANCOLD) recommend that one of the key objectives of integrated TSF planning is to ‘plan all phases of a tailing dam’s life to ensure adequate storage capacity including early closure ’ (Australian National Committee on Large Dams Incorporated (ANCOLD), 2012) this is often overlooked by owners who are focused on fulfilling the mine’s potential and early closure is not on their radar.CITATION:Ind, M J, Rynhoud, M and Brand, K, 2016. Life-of-mine spillway strategy – managing risk associated with surface water at a tailings storage facility, in Proceedings Life-of-Mine 2016 Conference, pp 209–211 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By T J. McGavin

This paper examines the fire life systems implemented in two existing tunnels and discusses whether the standards used were appropriate. It focuses on the Terrace Tunnel as this upgrade and refurbishment is complete.The New Zealand Transport Agency (NZTA) manages six tunnels on the State Highway network with two of these built in the last seven years. The Terrace Tunnel, opened in 1978, was refurbished with modern fire life safety systems in 2010–2012. An interim upgrade of the Mt Victoria Tunnel, opened in 1931, was also carried out at this time.In present times, few existing tunnels have undergone significant upgrades and refurbishments. The Terrace Tunnel required: new power supplies, control buildings, lighting, wall panels and jet fans, a deluge system, emergency exit lights and way-finding lights, a public address (PA) system, a radio rebroadcast system, lane control sign (LCS) and variable message sign (VMS), an over-height detection system (OHD) and a new tunnel management system.In the absence of suitable guidelines, various standards were used to carry out the refurbishment. The Austroad Guide to Road Tunnels and AS4825 Tunnel Fire Safety, although designed for new tunnels and not specifically intended for existing tunnels, provided a framework. A multi-criteria assessment of risk (MCAT) was carried out to determine the systems to be provided.The Terrace Tunnel has perhaps set a benchmark for refurbishing existing tunnels as few projects of this type have been completed recently. This paper examines the process and the outcomes.CITATION:McGavin, T J, 2014. The refurbishment of the Terrace and Mt Victoria Tunnels, Wellington, New Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 87–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J M. Galvin

The traditional engineering approach to assessing stability is based on comparing resisting force (capacity) to driving force (demand), or strength to working stress. In underground coal geomechanics, considerable effort has been expended on quantifying the strength of rock structures. However, this has not been matched by advances in determining the load acting on these structures, reflecting a reluctance by some to embrace numerical modelling to assess load magnitudes and distributions. Numerical modelling is a valuable aid as loading environments are a function of both the stiffness of the mine workings and the stiffness of the superincumbent strata and are statically indeterminate in most cases.This paper defines stiffness, which is often confused with elastic modulus. It shows that, effectively, stiffness encapsulates geology, depth of mining, panel width, pillar width and mining height. Therefore, these factors are variables that need to be taken into account when determining stress magnitudes and distributions about mine workings. A range of examples are presented that illustrate the significance of the stiffness of the superincumbent strata on surface subsidence; the magnitude and distribution of pillar and abutment load; and aspects of bord and pillar mining, pillar extraction and longwall mining. These examples provide bases for identifying the limitations of some empirical approaches to mine design, identifying how to compensate for some of these in design processes; and emphasising the need to make greater use of numerical modelling in understanding and quantifying loading environments in underground coal mining.CITATION:Galvin, J M, 2014. The significance of superincumbent strata stiffness and its impacts on coalmine design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Brent A. D, Olsen a. H, Mayfield P. L J, Grazier P. E

Concentrates produced from MnO2 and Fe203 ore fines have been targeted as potential feedstocks for direct metallurgical processing. Prereduction of pyrolusite-rich Mn02 sands to MnO has been investigated in batch and continuous experimental bubbling fluidised beds using CO-H2 reducing gas mixtures. This process has been found to produce a high grade feedstock suitable for smelting to ferroalloys or acid digestion for chemicals production. Similarly, production of highly metallised direct reduced iron (DRI) from hematite ore fines has also been investigated in batch bubbling bed reactors. Programs to characterise the reduction kinetics, fluidisation behaviour and defluidisation phenomena for both feedstocks are currently in progress to enable optimum process conditions to be determined.

Jan 1, 1995

By Feebrey CA, Duncan RA

The Ebor Volcano in northeastern New South Wales is an eroded example of a central-type intraplate volcanic-intrusive complex. It is of Miocene age (19-20 Ma) and has similarities to other central-type volcanoes in eastern Australia which may represent manifestations of sub-lithospheric hotspot activity. Thick lava flows are exposed around the Great Escarpment and are dominated by a tholeiitic basaltic suite, ranging from ol-tholeiite to qz-tholeiite to icelandite with ages of 19.2-19.6 Ma. On its western edge, the tholeiitic lava suite probably overlies remnants of basanite flows belonging to the Eocene (-48 Ma) Doughboy province, but elsewhere, minor alkaline basaltic lavas may be coeval with the tholeiitic suite. Several felsic bodies were emplaced into the volcano at -19.0-19.2 Ma and include subalkaline and peralkaline types. The Crescent Complex is a Miocene-age, strongly differentiated mafic to felsic intrusion in basement rocks and centrally located in pre-erosion reconstructions of the Ebor Volcano. It is interpreted to be a major feeder for the tholeiitic lavas based on age and composition. Evolution of the dominant tholeiitic suite proceeded from a parental ol-tholeiite magma, through qz-tholeiite, icelandite and small volumes of felsic rocks by fractionation of plagioclase, olivine, clinopyroxene and titanomagnetite, accompanied by enrichment of SiO2, F,FeO/MgO, alkalies and HFSE.

Jan 1, 1995

The intent of this address is to look forward into the 21st Century and present certain thoughts as to how underground coal mining might be conducted. The views in this talk are based principally on the author's experience with mining practices in the United States. It may be difficult to accept, but the 21st Century is a mere 12 years away. What new techniques will be available? To develop an understanding of the way in which technology has been and could be changing, a two- stage analysis is made of mining technology for U.S. Coal. The first phase covers the period 1975 to the present, while the second includes 1960 to 1975. This historical perspective includes a view of underground production by mining methods, considerations of labour productivity, and a review of accident and fatality rates. Several topics are important features of this historical analysis. Among the most significant are: (1) the introduction of Ion-wall mining technology into U.S. underground coal mines, (2) the use of computers to assist in mine planning and design activities, (3) major efforts to improve health and safety performance, with emphasis on underground dust control, and (4) improvements in mining equipment with an eye towards increased reliability and up-time performance. Based on that historical perspective, projections are made in three increments. The first being immediately at the turn of the century, the second being a dozen or so years beyond that, and the third being at the quarter point of the 21st Century.

Jan 1, 1988

By E Broers, J Goh, S Davies

With recovery being important in optimising the business performance of a laterite and sulfide plant and with water being a precious resource in Australia, there has been increased pressure for companies to improve their methods of improving liquor recovery and improving water recovery in both laterite and sulfide plants. This has resulted in new control technologies such as the Manta Cube being applied on countercurrent decantation (CCD) and thickening circuits which is necessary to improve stability and optimise the liquor and water recovery in these processing plants. This paper describes the benefit of applying these new control techniques on CCD and thickening circuits in some of the mineral processing plants in Australia.

Jan 1, 2009

Comprehensive occupational health and safety legislation in Australia is comparatively recent. It follows the examples set in U.S.A. and U.K. a decade or more ago. In Western Australia the Occupational Health, Safety and Welfare Act was proclaimed in April 1985. It still has a long way to go before it achieves all its objectives. The mining industry has developed a substantial body of health and safety regulations under the Mines Regulation Act. Considerable practical expertise in such matters already exists, much of it developed from hard won experience. As a result it would prefer not to become engulfed in the new legislation. It would prefer to build upon the cooperatively developed policies and workable practices in the field of occupational health and safety with which it is familiar. Associated Minerals Consolidated Ltd. is a leading mineral sands producer in Western Australia and has continuously developed its occupational health and safety policy and practices. Under the banner of "Resource Control", AMC seeks to provide a safe and healthy working environment at all times. This is being achieved through a strategy of a policy, a defined organisational structure and a detailed programme, which together comprise the "Resource Control System". Some of the activities and achievements of AMC in the field of occupational health and safety are compared with the objectives of contemporary legislation, and details of some of the specialised areas of the Resource Control Programme are discussed. The paper will also highlight and discuss impractical areas of potential legislation.

Jan 1, 1986

By Caress ME, Knight MD

The eruption 75,000 y ago of the Younger Toba Tuff ignimbrite and associated ash-fall ranks as the greatest known volcanic event of the past million years. The ignimbrite is known to cover 21,000 km2 (it may extend farther under alluvium of the coastal plain) and forms a low-angle depositional shield centered on the Lake Toba caldera. The ignimbrite is largely nonwelded and shows systematic outward decreases in lithic and crystal contents and clast sizes. Coarse lithic lag breccias that occur at places 85 km apart point to two or more vents on a fissure having this length. The extensive associated ash-fall traceable as far as Malaysia and India is evidently a co-ignimbrite ash but could have a phreatomag-matic component. The Lake Toba caldera measures95 x 35 km and is >1 kn deep. It is not a single caldera but comprises several contiguous depressions and grabens diversified by two re-surgent domes. Earlier parts of the caldera are related to at least two earlier ignimbrites including the Older Toba Tuff dated by Chesner at 0.5 Ma. The caldera is elongated parallel to, and is only 25 km from, the great Sumatra strike-slip fault, and it can be considered almost certain that the caldera is in part a kind of pull-apart structure. The ignimbrites are very crystal-rich. There is no reason to think basaltic magma was involved in their emplacement. Together with ash-falls they have a total volume of several thousand cubic kilometers. They can be categorized as originating from partially crystallized granitic magmas that erupted because tectonic pull-apart occurred several times across the pluton. Small rhyolitic lava domes on fault-lines comprise the youngest volcanic products.

Jan 1, 1990

By B C. Povey

HPGR technology has been used at a number of magnetite mines in the world and have significant energy advantages over SAG and AG technologies. The early design at Los Colorados in Chile has been in operation for more than 12 years - and operates very successfully though only reduces the feed size to -5mmThe Whyalla project magnet design pushed the concept to produce a preconcentrate of 80%-350micron - a significant reduction on previous plants though with some wear problems in the early years. The Karara design backpedalled slightly and will only crush to 80%-1.8mm.However, the design issues of using a HPGR to further reduce the feed size continue to be explored. The aim is to reduce the process risks associated with wear and also to reduce the complexity of the downstream process - with consequent benefits in terms of capital and operating costs.The designs are being developed for a couple of projects - one planned to produce 20Mtpa of concentrate with the potential to not only remove SAG and AG milling but also ball milling. The concept is to use multiple passing through the HPGR since, on the data available, the efficiency of the HPGR to reduce size does not significantly diminish as the feed size is reduce. This can be have benefits in both capital and operating cost.CITATION:Povey, B C, 2013. Pushing the use of high pressure grinding rolls in magnetite circuits, in Proceedings MetPlant 2013 , pp 176-189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

By S P, F Villanueva, R Palomo, D Meadows

During 2002, design and development of the worldÆs largest flotation cell was completed. The cell is the mineral industryÆs first 257 m3 flotation cell, and represents a major development in the design of larger flotation cells, with a 50 per cent increase in cell volume over the widely installed 160 m3 WEMCO« SmartCellTM flotation machine. It is anticipated, in the next few years, world-class copper sulfide concentrators will incorporate 257 m3 flotation cells in their rougher-scavenger flotation circuits. The prototype 257 m3 cell, No 250 SmartCellTM flotation machine is installed in Minera Los PelambresÆ existing rougher flotation circuit. The machine is located in front of the first cell in Row 1 and is followed by nine No 130 SmartCellTM flotation cells. The unit has been in operation since April 2004, and has proven itself in this duty. A key to the successful development of the equipment has been the emphasis placed on fundamental hydrodynamic scale-up criteria. Hydrodynamic factors include superficial gas velocity, water (pulp) circulation through the draft tube, and pulp mixing (distribution) characteristics. This paper will review the scale-up criteria of the No 250 flotation cell, and a case study will be presented on the in-plant testing of the equipment. The case study will document the metallurgical and hydrodynamic performance of the machine. It will also illustrate the economic benefits derived by incorporating larger flotation cells in a modern copper sulfide concentrator.

Jan 1, 2005

The Bau Goldfield lies in the southwestern corner of Sarawak in East Malaysia. Evidence of past mining in the form of open pits and adits can be found over an area of 250 sq kin, centred on the township of Bau. Chinese were mining gold in the district as early as 1820. The Bau Goldfield so far has produced approximately two million ounces of gold, from alluvial deposits and over 50 hard rock mines. The largest single producer was the Tai Parit mine (700 000 oz) which was operated by the Borneo Company from 1898 to 1921 and by a local Malaysian family from 1991 to early-1997. Over the past ten years, gold resources totalling around one nullion ounces have been delineated through systematic exploration using modern techniques, with the bulk of the resource hosted in two deposits (Jugan and Pejiru).Triassic to Jurassic andesitic volcanics and coeval intrusives are the oldest rocks that crop out in the Bau Goldfield. These igneous basement rocks are unconformably overlain by 500 m of late Jurassic, massive, micritic limestone which in turn is overlain by a 1500 in thick flysch sequence, composed mainly of shale. Basement rocks and limestone are exposed along the hinge of a ENE-striking anticline that passes through the Bau district (Bau Anticline). A NNE-striking belt of Miocene granodiorite porphyry stocks and dykes also passes through the Bau Goldfield. All of the known gold deposits lie within 5 km of this zone of intnisives, with a concentration of deposits at the intersection of the intrusive hell with the Rau Anticline.

Jan 1, 1997

Confirmation of significant mineable reserves of high grade silver ore at Elura Mine has led to the development of a high cost, high recovery mining system. At the contact of oxidised and sulphide ores lies a supergene zone of enrichment which has provided a contrast, not formerly imagined, to Elura's primary development and stoping operations. Because of the soft nature of the ore, intense ground support practice has been combined with a panel cut and fill continuous mining system to extract a reserve of small, but most valuable Proportions.

Jan 1, 1988

Equilibrium in the reaction H2(g) + [%0] (in liquid copper) = H2O (g) was investigated at temperatures between 1200 -and 1350°C with p(H2Oj/p(H2) ratios between 1 to 15. A semi-microbalance was used for direct measurement of dissolved oxygen in molten copper. Oxygen was found to obey Henry's law under the experimental conditions used. The standard free-energy change for the above reaction is given by Equation 1where 1 weight per cent solution is the standard state for dissolved oxygen.For the dissolution of oxygen in copper according to 1/2 O2(g) = [%0] (liq. Cu), the standard free energychange is given byEquation 2.

Jan 1, 1973

By O Tiili, A Dixon

Many minerals processing plants need to have greater efficiency in current times and optimise their process performance in order to maintain high profitability. This is even more so in the current economic climate. In the case of large flotation cells, such as TankCell«-300 with over 300 m3 active capacity, ensuring consistent operation and optimal flotation conditions is particularly critical, given the high impact on overall process and throughput of such cells. As there are fewer cells to control and monitor, there is also a lower initial capital cost for instrumentation - the requirements, however, are higher. Despite such compelling reasons, instrumentation and basic control in flotation cells has not changed much in recent years. The standard is still to use traditional feedback (PI algorithm) controls for slurry level and flotation air. A new advanced instrumentation and control package for large flotation cells has recently been developed by Outotec and has been installed at Macraes.In addition to the standard basic instrumentation and control, the new system at Macraes consists of a froth image analysis system, a froth velocity control, and a level control system which utilises adaptive feedforward compensation. There are three TankCell«-300 cells in operation at Macraes since November 2007 and the new control system was commissioned in December 2007.The paper will include comparative data from pre- and postsystem installation and discusses benefits including optimised recovery, improved performance, as well as ease of operation.

Jan 1, 2009

By C Nucifora, M Landers, J Jones, G Maddocks, K Mandaran, A Forbes, W Wilson, S Newman

Glencore’s Mount Isa Mines Limited (MIM) operates the Mount Isa open cut and underground copper (Cu) and zinc-lead (Zn/Pb) mines near Mount Isa in Queensland, Australia. Tailings from processed Cu and Zn-Pb ore is contained in a 1,315 ha shallow (< 35 m deep) multi-cell valley fill tailings storage facility (TSF). Static geochemical testing conducted by MIM over the life of mine (LoM) verifies that the Cu, and Zn-Pb tailings has a wide range in sulfide content and diverse mineralogy with significant acid neutralising capacity (ANC) in some samples. The tailings are predominantly classified as potentially acid forming (PAF) using static analytical methods. Kinetic leach testing using free draining columns and humidity cell tests simulating tailings placed on the surface of the TSF suggest that the tailings samples are likely to remain non-acid forming (NAF) for 10 to 40 years under aerial exposure, and much longer than this under saturated conditions within the TSF. During this period of weathering, as ANC is depleted, the neutral pH drainage may contain elevated concentrations of some elements including sulfate, manganese and zinc. Only when the ANC is depleted would the tailings then begin to produce acid drainage. CITATION:Mandaran, K, Jones, J, Nucifora, C, Maddocks, G, Landers, M, Forbes, A, Wilson, W and Newman, S, 2018. Mount Isa Mines Rehabilitation Materials Sampling and Analysis program for closure planning, in Proceedings Life-of-Mine 2018, pp 138–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930