Search Documents

By P Nichols, C te Kloot, A Harrison

Ernest Henry mine (EHM) is a sub-level caving operation located in north-west Queensland, Australia. Located below a previously mined open pit, the underground operation ramped up production to 6.8Mt/a in 2017. The EHM ore body dips at 45 degrees to the South and therefore requires each level to “step out” from the level above as seen in Figure 1. Within this step out zone it is important to both maximise recovery and allow for efficient operation of the underground workings production to bring the level up to full production as quickly as possible. Throughout the step out design process, a combination of further defining the ore boundary, using lessons learnt from production performance on upper levels and the introduction of design improvements, has reduced the production ramp-up time, decreased costs and increased recovery for a single level at EHM. CITATION: Nichols, P, te Kloot, C and Harrison, A, 2018. Case study – Ernest Henry Mine: designing step out zones in an inclined sub-level cave, in Proceedings Complex Orebodies Conference 2018, pp 53–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

The Favona Underground Project is located approximately two kilometres east of Martha Mine Open Pit in Waihi, 150 km south east of Auckland, New Zealand.   The underground reserve of 354 koz Au contained in resources of almost 600 koz lies within 600 m of the existing process plant presenting an attractive development target in a challenging environment.   The Martha Mine Open Pit is surrounded by urban housing on the north western edge of Waihi township and the Favona Underground abuts residences on the eastern edge of town. Environmental, community and social licence aspects influence project strategies as the new underground mine extends mining in a town that is planning for closure of current open pit operations in late 2006.   The Favona Underground Project has successfully passed through a detailed feasibility study, the third stage of the five stage Newmont project appraisal system. Methodologies used in the feasibility study and parallel permitting draw on a high level of stakeholder involvement to streamline the development and permitting phases.   This paper discusses the project appraisal process and design innovation required for developing an underground mine adjacent to town.

Jan 1, 2004

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

By P Ritchie, E H. Briese, N A. Currey

Kidston Gold Mines, located in semi-arid North Queensland, Australia is currently in its closure phase. Highly innovative and comprehensive rehabilitation strategies were employed at the site, including the direct revegetation of the surface of the tailings storage; the construction of a tailings sediment entrapment pond; the construction of a spillway to drain large rainfall events from the surface of the tailings; the construction of store/release covers over the tops of the waste rock dumps; the sheeting with oxide waste rock of the waste rock dump slopes; the partial back-filling of the initial Wises Hill Pit with waste rock and thickened tailings produced from the subsequent Eldridge Pit; the partial flooding of Eldridge Pit following the end of mining; and the construction of wetland systems to treat contaminated tailings and waste rock dump seepage. These closure strategies involved the careful consideration of water management. Specific water management issues included understanding the water balance of the tailings dam; the operation of the tailings dam sediment entrapment pond and spillway; understanding the water balance of the store/release waste rock dump covers; the importance and sustainability of vegetation on the tailings, store/release waste rock dump covers, and on the sheeted waste rock dump slopes; the level and quality of water in the partially flooded Eldridge Pit; and the treatment of contaminated seepage in the constructed wetlands. The seasonal and highly variable rainfall experienced in this semi-arid climate posed a number of challenges for the management of water on the site post-closure. The paper details these challenges and highlights how they were resolved over the period leading up to and following the end of mining.

Jan 1, 2003

This paper describes several sources of external dilution affecting the stope walls during underground sub-level and bench stoping. Factors which control ground behaviour such as the geometry of the openings, the influence of geological discontinuities, stress re-distribution and blasting practices are discussed. Crown stope instability due to stress concentrations induced by changes in the excavation geometry, is discussed and the most efficient ways to sequence blasting within a stope are analysed. Effects of undercutting by blasting, blast damage in the near field and cut-off slot blast designs are analysed. The influence of dynamic loading on the exposed walls as well as the practice of blasting fill passes within stope crowns are discussed.

Jan 1, 1995

By Espi J

The Nena high sulphidation deposit, located in the Sandaun Province, PNG, contains a measured and indicated resource of 51 Mt of copper ore grading 0.5% Cu and 0.6 g/t Au at a 0.5% Cu cut-off. The copper orebody is overlain by an 18Mt oxide gold resource grading 0.1 % Cu and 1.4 g/t Au at a 0.6 g/t Au cut-off. The deposit is hosted in advanced argillic altered pyroclastics interstratified with lavas, volcanoclastics, epiclastics and sediments of the Debom Volcanics within the Frieda River Intrusive Complex. Foraminiferal sediments indicate the Debom Volcanics to be Early-Middle Miocene in age. Alteration is elongated along, and concentric about a northwest trending structure (Nena Structural Corridor) which is about 7km in length. The inner two alteration types, residual and massive silica-alunite are strongly brecciated and host the bulk of later hypogene Cu-Au mineralisation. Weakly mineralised weak silica- alunite and barren peripherally zoned clay alteration surround the inner mineralised alterations. The hypogene sulphide deposition was polyphasal, episodic and is zoned from north to south from covellite-enargite ¦ chalcocite (5600N to 5200N) to a mixed enargite-luzonite (5200N to 4700N) to luzonite-stibioluzonite (4700N to 4400N) in the south within a 1200m long by 300m diameter sub horizontal pipe like body. Paragenesis studies indicate that pyrite ¦ marcasite were introduced early with barite and black native sulphur before deposition of banded pyrite (melnicovite) with barite during a period of brecciation. Continued brecciation allowed bladed covellite ¦ chalcocite followed by enargite-luzonite-stibioluzonite ¦ pyrite (brassy) and minor acicular covellite deposition. Yellow native sulphur and trace amounts of galena were deposited in remaining pores. Pre-acid alteration intrusives domed the mainly volcanic stratigraphy in the southwest and post-mineralisation porphyries in the northeast truncate mineralisation. Supergene processes and erosion have modified the top of the deposit, creating a 45m thick goethitic-scoroditic-haematitic gold cap above a 40m thick (on average) chalcocite rich supergene blanket. Lesser amounts of digenite, covellite native copper and rarely seen malachite occur in the supergene copper zone.

Jan 1, 1997

By Greenhalgh L. P H

The opportunities offered by an increasingly volatile world invite the international consultant or engineering services contractor to broaden attitudes, diversify interests, expand capabilities, retain and develop specialist skills and base judgements upon sound principles and solid experience. The wide-ranging scope of this review reflects such a change but the topics of discussion are not intended to be exhaustive or to detract from many other current developments.The subject of environmental protection, effluent control and pollution prevention is a primary consideration in the application of many mineral processing technologies but is not covered here. There is an array of developments relating to noxious gas emissions and toxic wastes and the paramount importance of this matter justifies comprehensive conferences dedicated solely to the application of suitable measures. This review concentrates therefore on the main stream processing techniques for the primary recovery of values.

Jan 1, 1993

Attention is drawn to the largest eruptions with dense rock equivalent (D.R.E.) volumes approx-imating 50 km3. These have been strongly clustered during the last 40 000 years, with 11 recognised in the period 35 000 to 22 000 years ago, and 10 in about the last 9000 years, but none in the period 22 000 to 9000 years ago. With the latest such eruption, at Tambora, only 175 years ago, it is likely that we remain in a period of increased activity. During the last 100 000 years, roughly the period during which modern Homo sapiens has existed as a species, there has only been one eruption an order of magnitude larger (>_ 500 km3 D.R.E.). This took place at Lake Toba, Sumatra, about 75 000 years ago, and is estimated to have deposited ash to a thickness of a centimetre or so in parts of Ethiopia, Somaliland, Saudi Arabia and Iran, and to a thickness of a few millimetres in the eastern Mediterranean. The average interval between global eruptions of this magnitude is probably about 40 000 to 50 000 years. Insufficient work on the Quaternary history of volcanoes has been carried out to suggest where the next such eruption might occur. At Yellowstone, which has been well studied, the average interval between very large explosive eruptions is about 700 000 ¦ 120 000 years.As a prerequisite for magnitude-frequency analysis of eruptions, and hazard and risk impact assessments, it is important to classify past eruptions in a consistent manner. In an attempt to find a universally applicable method to estimate order of magnitude D.R.E. volumes from the distribution of airfall tephra, an empirical correction has been derived for the elongation of tephra dispersal fans due to wind. Dispersion distances for various thicknesses of tephra, recalculated for windless conditions, have been obtained from a study of about 40 tephra isopach maps for which D.R.E. volumes have been calculated, and a range of distances derived, equivalent to D.R.E. volumes from 106 m3

Jan 1, 1990

By T Connor

Alkali emissions are one of the environmental challenges facing alumina refineries. Queensland Alumina Limited (QAL) is undertaking a number of initiatives to continuously improve its environmental performance. One of these is a program aimed at the reduction of alkali emissions. Alkali emissions originate from a number of sources (eg elevated open tanks), and its level depends on a number of process parameters/ mechanisms (ie splash filling, thermal currents in tanks, streams discharged from a pipe, tank temperatures, atomisation) and climatic conditions (eg wind speed and direction, rain, etc). Under normal operating conditions, there is a continuous low level of alkali emissions from the plant. Certain vessels within the plant have been identified as major contributors to this level of emission, while certain activities within the plant contribute to a temporary elevation (æspikeÆ) of alkali emissions. QAL developed a method using phenolphthalein-treated pads to measure emissions within and outside QAL boundaries. These provide no information about mass emission rates but are important for detecting if alkali material is present. Since mass emission rates are important for determining if improvements in emissions are made, QAL identified the need to design an improved sampling method. Following the development and implementation of a sampling and analysis method to monitor alkali emission concentrations, QAL is conducting a number of feasibility studies evaluating a range of alkali emission reduction options. The alkali measurement method will be used to track and demonstrate progress in this environmental initiative. This paper will discuss the measurement method and emission reduction options being evaluated.

Jan 1, 2005

By M B. Lovitt

At present there exist few engineering calculations and principles to determine exclusion zones for personnel in the vicinity of underground explosive storage areas. This paper is written to encourage discussion and proposes a method to determine the impact of a blast wave through scientific principles. Then, criteria to determine an ‘exclusion zone’ need to be identified.There has been much work on identifying the pressure rise and the energy of explosive detonations underground but little to develop standards in criteria that can be used to identify exclusion zones for useful design of underground infrastructure. The author presents the newest ways of calculating the pressure rise and energy (impulse) of detonations and puts forward some criteria to be used in the identification of personnel exclusion zones to spark peer review and discussion of these criteria towards developing standards for engineering design.Smith and Sapko (2005) used Sach’s scaling laws to develop a relationship for both pressure rise and impulse, which incorporated factors for intersections. Intersections will have a large bearing on the peak pressure and the energy of the blast wave and needs to be incorporated. Silvestrini, Genova and Leon Trujillo (2009) developed the scaling laws with an energy concentration factor to predict blast propagation in partially confined geometries and together the author has proposed equations for determining the peak side pressure and the impulse in a tunnel. Given the weight and type of the explosive, the average cross-section of the tunnel complex and the number and type of intersections encountered, the pressure and impulse can be calculated.The military has carried out many investigations as to the influence of blast pressure and impulse on the human body. Lung damage, ear damage and velocity knock down are three of the criteria standards that are presented as possible methods of determining exclusion zones around an underground explosives magazine. The author suggests that the velocity curves presented by Bowen, Fletcher and Richmond (1968) could be an acceptable method of determining an exclusion zone as it incorporates the side pressure and the energy of a blast wave to determine the ability of the wave to knock down personnel.CITATION:Lovitt, M B, 2014. Exclusion zone calculation for underground explosives storage, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Abishev D. N, Balakirev V. F, Davydov G. I

The problem of recovery of cobalt products from poorly oxidised nickel ores (Kempirsaisk deposit) and pyrite concentrates with a low content of cobalt (Sokolovsk-Sarbaisky deposit) has not been solved to the present time in Kazakstan. The balance reserves of nickel ore of the Kempirsaisky deposit make up more than 35 million tons with a nickel content of 1.13 per cent and cobalt content of 0.05 per cent; besides there are 110 millions tons of out-balance ores (Anon, 1995). In a tailing dump of Sokolovsk-Sarbaisk Mining and Productional Association more than 320 million tons of tailings of wet magnetic separation have accumulated, which contain 7.2 per cent of sulphur, 0.022 per cent of cobalt, 0.012 per cent of nickel, 0.094 per cent of copper, 0.079 per cent of zinc, 16.45 per cent of iron, and from which a high quality pyrite concentrate car) he separated through flotation, containing 48 - 50 per cent of sulphur, 44.15 per cent of iron, 0.141 per cent of cobalt, 0.07 per cent of nickel, and 0.10 per cent of copper. The well-known technological flow charts for cobalt and nickel recovery from the tailings of sulphide-magnetite ores dressing (to give pyrite concentrate) and from oxidised nickel ores, are not profitable at the existing prices for metals, but are not worthless and require significant capital investments for the realisation of their value. The flow chart `sulphate roasting - leaching - solution processing' is used widely for combined processing of cobalt-containing pyrite ores and concentrates.

Jan 1, 1996

By Torabi S. R, Daly C. R

Wind blast is the sudden movement of air displaced by the massive collapse of roof rock in underground openings and is experienced as a high velocity flow of air through adjacent workings. The initial flow in the outbye direction is often followed by 'suck back', that is a reverse flow of air towards the newly created void. As part of the Wind Blast Project, undertaken by The University of New South Wales, Department of Mining Engineering, a physical model was constructed. One of the functions of the laboratory wind blast model is to provide insight into the dynamics of the interaction between the falling strata and the air being compressed below. During a collapse, some air is expelled into the surrounding roadways while the remainder penetrates towards the top of the roof elements. In this paper two aspects of the rock mass properties which influence the phenomenon are considered: - Flow paths through the falling roof element, ie the permeability of the roof element; - Bed separation prior to the fall which introduces a void above the roof element. A series of tests was carried out utilising the physical model in order to investigate the relationships between the flow of air through the simulated roadways, the variations in gauge pressure above and below the falling roof element, and the acceleration and terminal velocity of the latter, all as a function of the flow paths through the roof element and of the extent of the void above. The results of comprehensive tests using the wind blast physical model suggested that the time history of outbye air flow in the simulated roadway comprises two distinct phases. a) A primary phase, characterised by a high velocity flow of air which exhibits a peak and corresponds to the period during which the roof element is accelerating. The peak air velocity is related to the acceleration of the roof element. b) A secondary phase, characterised by a residual air flow of a lesser velocity than in the primary phase and corresponding to the period during which the roof element is falling at its terminal velocity. The velocity of the residual air flow is directly proportional to the terminal velocity of the roof element. In a monolithic collapse of a roof element it was shown that the presence of flow paths in the roof element increased the air velocity in the roadway in both the primary and the secondary phases. The presence of an air-filled void above the roof element, on the other hand, influenced the air velocity only in the primary phase by increasing the peak air velocity. The overall duration of the process was however decreased as a result. 'plug type' collapses, where roof failure extends to the ground surface, potentially generate the highest peak air velocities likely to be encountered during wind blasts.

Jan 1, 1995

By S A. Ravishankar, W Perez

Flotation is one of the main concentration processes to purify kaolin clay via the removal of naturally occurring impurity minerals containing Ti and Fe. Currently, there are two types of collector chemistries used in the industry to float coloured impurity minerals. These are traditional tall oil fatty acids (TOFA) and specialty hydroxamate (AHX) based collectors. AHX based collectors have long been known to be the most selective collectors to float Ti and Fe based coloured impurity minerals (CIMs) as compared to TOFA based systems. AHX based collectors provide, not only improved selectivity and simplified process, but also more importantly, make it possible to treat certain kaolin resources that do not respond to standard TOFA systems. However, the relatively higher cost of straight AHX collectors has restricted broader application of these collectors in kaolin clay and other oxide flotation applications for a long time. Recent technological advancements, in both making and formulating AHX products more economically, increased the usage of these collectors in kaolin applications. Modified AHX products offer more economical alternatives and process options to provide high purity kaolin clay products for specialty applications based on cost-performance criteria. In this paper, the flotation performance of a series of newly developed AHX formulations is provided along with the characteristics of AHX flotation in general. In addition, flotation performance of earlier AHX collectors is provided based on published literature as background data.

Jan 1, 2005

By G J. Keyter, P J. Terbrugge, Yu Xianb

There has been disappointingly little development in the understanding of the behaviour of rock slopes in open pit mines over the past 30 years. The lack of development in general, and of robust, standardised approaches in particular, are surprising in view of the æultraÆ deep open pit mines that are being developed to depths in excess of 1000 m. Research has recently been carried out into the occurrence of zones of extension strain in open pit slopes. This showed that very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. Results of the research will be presented for different slope heights, slope angles and horizontal to vertical in situ stress ratios. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning, producing easily measurable seismicity. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. Case studies of slope failure in two open pits will be described. In both cases failure occurred æsuddenlyÆ after very limited amounts of deformation. In the first, the slope crest moved suddenly upwards and backwards over a length of more than 200 m, with associated instability. In the second, the horizontal displacement of the slope face was almost an order of magnitude greater than the vertical displacement and occurred æsuddenlyÆ. A recently installed seismic system is detecting events in a significant zone behind the slope face. Both pits were in the 200 m to 300 m depth range at the time of the occurrences.

Jan 1, 2003

By Cunningham J. C

JUST prior to the war the Broken Hill South Ltd: raised, on the average, 6628 tons of ore per week, all of which was crushed and treated in the 4-section gravity mill and the slime flotation plant, for the recovery of lead concentrate carrying silver. The sandy residues from that treatment were railed to the treatment plant of the Amalgamated Zinc (De Bavay's) Ltd. for the recovery of zinc concentrate by flotation, on the joint account of both companies. Subsequent to that-since 1916-approximately 1000 tons of old dump slime were also treated weekly for the recovery of lead and silver as slime-lead concentrate.PLANT CAPACITYUnder this programme the Babcock and Wilcox boiler plant of 8 boilers was taxed to such an extent as to call for the installation of two additional boilers, each of 2690 sq. ft. of heating surface and 55 sq. ft. chain-grade area.The electric generators and the air compressors of the old powerplant were also loaded to their maximum capacity. In view of the fact that the old power-plant had been added to from time to time since 1901, and that further extension was notpossible, and as it was not, moreover, an economical arrangement, the whole question of power generation was reconsidered. The considerations that determined the installation of entirely new plant were as follows:(1) The need for more compressed air for underground work and more electric current for the extension of the slime-flotation plant for the recovery of zinc, as well as lead, as slime concentrates. Provision of additional power was also deemed advisable for the...

Jan 1, 1921

By Matthew SP, Hayes PC

The product morphologies formed on the reduction of dense wustite crystals are classified into three types,A) porous iron, B) porous wustite covered with dense iron and C) dense wustite covered with dense iron. The mechanisms of formation of these structures and the effects of impurity elements on the product morphologies are discussed

Jan 1, 1984

By P J. Chapman

Recent catastrophic failures of tailings storage facilities (TSFs) continue to highlight the need for a detailed understanding of failure modes and the defences that are in place within the design to mitigate the failure modes. However, in many cases the instrumentation devices and monitoring approaches selected during operation do not link back to the design defences and inappropriate or redundant instrumentation is often installed. Candidate instruments and monitoring approaches (critical controls) are presented and matched to critical failure modes, with clear linkages to the intent of each instrument/monitoring approach. Commentary on where complementary measurements with independent technology types are recommended to provide greater assurance of trends to the design engineer or TSF owner is also presented. In response to the recent TSF failures, an increasing focus is being placed on instrumentation and monitoring relating to slope instability and safeguarding against the potential for static liquefaction, using a critical state soil mechanics framework. To support selection of appropriate zoning within a stability model, three complementary devices are recommended – vibrating wire piezometers to provide an indication of pore pressure and allow the phreatic surface to be inferred, tensiometers to confirm the presence of unsaturated conditions (and hence low potential for undrained failure) and moisture content sensors to provide an indication of void ratio, and hence state parameter, in saturated zones. The combination of VWPs and tensiometers will provide complementary measurements in the saturated and unsaturated zones, and also provide information on the extent of any near-saturated zones, provided that sufficient instruments are installed.

Jul 1, 2021

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

Renison Limited produces high and low grade tin concentrates at an annual rate of 5000 tonnes of contained tin metal. In spite of the fine average cassiterite grain size, emphasis is placed on gravity concentration methods to produce a high grade final product. Cassiterite flotation is considered and operated as a gravity circuit scavenger responsible for approximately 15 percent of recovered tin metal as a fine grained low grade concentrate. Metallurgical problems mainly result from ore-type variations which may be aggravated by a number of circulating loads. The rationalisation of circuitry is being studied to provide more effective control by operators and to allow exploitation of current control and modelling techniques.

Jan 1, 1977

By J Ta’ala, M Handyside

Mechanical sampling from conveyors has historically been a staple in the iron ore industry when information related to chemistry, sizing and moisture is required. In order to comply with ISO 3082:2009, samples can be taken either on a mass or time basis provided no bias is introduced by periodical variation in quality or quantity. With the introduction of mechanical sample carousels, you also have the opportunity to collect samples on a mass or time basis. In order to optimise automatic sample stations in a changing production environment, BHP Billiton Iron Ore (BHPBIO) has developed a simulation model that enables the various combinations of mass–mass, mass–time, time–time and time–mass to be investigated.The sample station model can utilise actual (variable) feed rates to achieve high resolution and enables the simulation of sample size variation. Cutter speeds and other settings can then be adjusted to better optimise the performance of the sample station with regards to optimal sample size as well as ensuring the sample station is in compliance with ISO 3082. The model can also assist process engineers in adjusting settings to better optimise the sample station and reduce unwanted events such as blockages. The model can be easily modified to conform to various sample station designs. This paper demonstrates the use of the model and the benefits that can be achieved.CITATION:Handyside, M and Ta’ala, J, 2014. Simulating time versus mass basis?sampling, in Proceedings Sampling 2014 , pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014