Search Documents

By Harold Markus, Gerhard Derge, Arthur Grobe

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from ½ to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.1°. Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By R. J. P. Lyon

It is usually assumed1,2 that ore deposition is relatively slow, taking place over tens of thousands of years. Yet many syntheses and phase changes can be completed in the laboratory in a matter of hours, under essentially the same pressure and temperature conditions to be expected in nature. Much has been written about geothermometry, and Ingerson's recent summary2 an hardly be surpassed. Rather than review the whole field, this article will deal specifically with diffusion rates in solid solutions* of the sulfide minerals. In the study and application of temperature-indicating phenomena to problems of ore genesis, the time factor has often been neglected. In the particular case of sulfide systems, the speed of unmixing and diffusion of the constituent phases in the solid solutions has seldom been considered when laboratory data are applied to the genesis of natural sulfide ores. Chalcopyrite and Bornite Intergrowths: Chal-copyrite and bornite are copper iron sulfides often found in association. In many ores the individual grains appear to have mutual boundaries, but bladed intergrowths are quite common. Early workers in the field, " deduced that while these patterns could have been formed by replacement, they could be experimentally reproduced from the unmixing of solid solutions of the two previously homogenized at 475°C. Much of the ore from Roan Antelope mine in the Rhodesian Copper Belt exhibits these bornite-chalcopyrite intergrowths, from which it has been deduced that the ores could have been subjected to a minimum temperature of 475°C. In several recent interpretations,' this temperature rise has been considered to result from a regional metamorphism of an original syngenetic copper-bearing sediment. The same temperature rise to 475 °C was suggested from similar intergrowths in the sulfide- • The general subject of solid solution in structurally similar minerels is treated in many texts'. :' ' and will not be further elucidated. bearing ore from the Happy Jack uranium mine8 on tile Colorado Plateau, although this temperature had a different origin. In 1931 SchwartzV etermined that 475°C represented the unmixing temperature of his bornite-chalcopyrite solid solutions but, more important, that the characteristic intergrowths of bornite and chalcopyrite could be preserved only if the solid solution were chilled quickly to room temperature. This significant corollary has been almost completely neglected by both Davis and Miller.7,8 By suitably decreasing the cooling rate, Schwartz found that the original pattern of the intergrowth was reformed (Fig. 1). The cooling rate was critical. In cooling from 475°C to room temperature in

Jan 1, 1960

By William Marsh Baldwin

[Two of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Hencky1-3 and the St. Venant7-10 equations. HUBER-VON MISES-HENCKY EQUATION The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,? al, a2, and a3 satisfy the equation: (s1 - s2)2 + (s 2 - s 3)2 + (s 1 ? s3)2 = 2K2 [I] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities a1, a2, and a3 are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4,5 (Fig. I). The radius of this cylinder is v2/3K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values s 1/K = si, s 2/K = s2, s 2/K = s3 to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (s1 - S2)2 + (S2 - S3)2 + (Sl - S3)2 = 2 [2] and the radius of the cylinder becomes 2/3v. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elastically, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates s1, s2, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordi¬nate axes). Let us now pass a line through the point on the circle and the point on the axis.]

Jan 1, 1946

By Carl F. Floe, Michael B. Bever

TRE solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to 1300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. REVIEW OF PREVIOUS WORK The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available. According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar6 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwas3é reported large hydrogen solubility values for several compositions of copper- tin alloys, which appear to be in error.

Jan 1, 1944

By Frederic Lahee

THE total production of crude oil in Texas during 1924 was said to be 133,613,985 bbl. as compared with 125,991,628 bbl. in 1923.1 Subtracting from these figures the yield of the Gulf Coast fields, there remains, for the other part. of Texas, a yield of 106,272,573 bbl. in 1924, as compared with 101,931,595 bbl. in 1923. This represents an increased, production of over 4,250,000 bbl. for all of Texas outside of the Gulf Coast or Salt Dome fields. Within this same region, in 1924, there were 3624 completions, of which 2352 were oil or oil and gas wells, 7 were gassers, and 1265 were dry holes. Thus, nearly 35 per cent. of the completions were dry holes. In 1923, there were 4134 completions, with 2853 oil or oil and gas wells, 2 gas wells, and 1279, or 31 per cent. of the total, dry holes. Outside of the Gulf Coast region, six major pools were discovered and developed in 1924.; two pools, previously discovered, were extended far beyond their limits at the end of 1923, and many smaller pools were opened. The major pools were the Big Lake field, in Reagan Co., the New Richland field, in Navarro Co., the Harmel, Carey, and Ragle pools, in south Archer County, and the Wortham field, in Freestone and Limestone Counties. Fields that were notably extended were the Panhandle producing area and the Luling field. Many wildcat wells have been drilled; most -of these were failures, but several opened .pools and several have had sufficiently favorable results to. lead to further drilling. The activity of the operators in searching for new production was very intense during 1924, and indications point to as feverish a campaign during the coming year. This will be stimulated by rising prices for crude oil. There are good reasons for believing that new pools will be discovered along the Mexia fault zone, in Archer, Young, Baylor, and Throckmorton Counties, in the great central region of Texas where we now have the Mitchell County and Reagan County pools, and very likely in the eastern Red River Counties including Cooke and Grayson. On the other hand, with the opening of the year, there is no new big pool in sight. An outstanding feature of the production end of the business is the increasing reliance placed on geological work and geological recommendations. Not in five or six years has there been such a demand for first-class geologists.

Jan 3, 1925

By B. R. Coil, C. A. Ross

NEW demands for underground power in the Miami mine of the Miami Copper Co., Miami, Ariz. has brought about expansion of the distribution system for both ac and dc power. Progress in mining equipment and the normal changes in the mine were responsible for this increased demand. Early power requirements were for pumping and haulage. A 440 v ac power line down No. 5 shaft took care of a small pumping load and shaft station lighting, 275 v dc power was generated by motor generator sets on the surface, with a churn drill hole from surface to the 570 haulage level serving as a cableway. Electric lights were installed where power was available, and thus were confined to the haulage level and shaft stations. All industrial power in the Miami area is 25-cycle, which dates back to the hydroelectric generator installation at Roosevelt Dam in 1908-10. The Problem The main haulage level was moved to the 720 level and later, to the 1000 level, requiring a longer feeder line with the resultant voltage drop. Also, as mining progressed to the east, the churn drill hole for the power cable would have been subjected to subsidence cracks. The first extension in the use of electricity was in electric blasting. About 1935 the mine went to electric blasting, using the dc haulage current. Bringing electric current to the working levels of the mine for blasting greatly expanded the use of electric lights. Lights were used in tool rooms, powder and cap magazines, stairways, and other semi-permanent installations. Like all mines, Miami Copper began to study and experiment with mechanical mucking and transportation of ore by slushers, shakers, and belts during the late 1930's and early 1940's. At the beginning of the program, power was supplied from the haulage level 275 v dc system. Later it became necessary to run a cable, carrying 440 v ac power, down the No. 7 ventilation shaft. The increased use of power came about gradually, and many new problems were added, not the least being the introduction of switch boards and power cables into the working areas of the mine, where drifts and crosscuts take weight, and require repairs. The 25-cycle current presented special problems, in that 25-cycle transformers are twice as large and about 2V2 times as heavy as 60-cycle transformers of the same power output. The 25-cycle transformers were considered too large for installation in the mining areas. In 1947 the distribution system was revised and standards were adopted, governed by the following

Jan 1, 1952

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By Will Mitchell, T. G. Kirkland, C. L. Sollenberger

BENEFICIATION of a Korean scheelite ore has been studied during the past year in the Basic Industries Laboratory at Allis-Chalmers Manufacturing Co. A flowsheet has been recommended including flotation, gravity separation, and a final cleaning by a magnetic separator. The investigation was continued in the field of flotation in order to establish the effect of certain variables on recovery and grade of rougher concentrates. The results of this investigation are recorded here. Mineralogy The scheelite ore was obtained from Korea and was mined from the Sang Dong deposit. This deposit is described as lying in gently dipping metamorphosed sedimentary beds of Cambrian age.' The metamorphism was probably either metasomatic replacement or recrystallization, or both, with subsequent hydrothermal deposition. Igneous bodies in the form of granite porphyry have been found within 7 km of the main shaft and are considered to be a possible source of the mineralizing solutions. The Myobong formation, the host for the Sang Dong deposit, was laid down in middle Cambrian times and consists of series of mudstone, siltstone, shale, and marl, with local stratification of mica schists, hornfels, and tactites. The scheelite is found in quartz bands in the tactites. Although there are six of these bands, only one, the "main bed" averaging 1.75 pct WOs, has been mined to any extent. The ore sample as received in the laboratory was the product of a cone crusher and was all —2 in. The rock appeared to be even textured, medium to fine grained, and gray green in color. No scheelite could be recognized by the unaided eye. However, under ultraviolet light of 2537 A, the scheelite fluoresced and could be distinguished from the gangue. Under the black light, the scheelite showed no definite vein structure but was disseminated throughout the specimen. The raw ore had a specific gravity of 2.96 and weighed about 125 lb per cu ft at —20-mesh Tyler. The —2-in. material was stage crushed through 20-mesh, and samples were cut for mineralogical, chemical, and spectrochemical analyses. Several polished sections were cut from hand specimens. Figs. 1 and 2 show quartz to be the matrix for scheelite. It was reported by Kim2 that the greatest scheelite concentration in the mine is found with a high concentration of quartz and a decrease in the abundance of garnet. Diameters of scheelite particles ranged from 1.2 mm down to less than 50 microns. Spectrochemical analysis showed the ore to be high in aluminum, bismuth, calcium, iron, magnesium, manganese, silicon, tungsten, and with lesser amounts of beryllium, chromium, lithium, sodium, and titanium. Chemical assays showed the —20-

Jan 1, 1952

By C. M. Young

Wherever salt is extracted from the ground as an artificial brine produced by pumping down fresh water to dissolve the salt, subsidence of the overburden is a possibility, though apparently few cases of such subsidence have been noted and detailed records are wanting. This description is intended as a record of subsidence that may permit the forcasting of similar occurrences in other cases; the data were supplied largely by R. B. Lee, city engineer of Hutchinson, Kans. About eleven years ago, ground movement occurred at a neighboring salt plant, when the surface assumed the form of a shallow funnel. Movement was probably due to a flow of sand into a well through a poor seal or a broken casing. The salt deposit increases in thickness from the east until at Hutchinson, where the subsidence occurred, it is about 310 ft. thick. The interbedded layers of shale vary in thickness from mere traces to about 7 ft. While knowledge of the shale content of the beds is not exact, the log of a shaft 3 miles east of Hutchinson indicates that shale forms about 25 per cent. of the total thickness. This shaft does not reach the bottom of the salt by about 60 ft., but there is no reason to think that the lower part of the bed is different from the upper. Logs of wells sunk to the bottom are not sufficiently detailed to be of much value. Above the salt is the shale of the well-known Red Beds. The thickness of this is variable, principally because of its eroded surface, but at the mine it is 340 ft. This shale is variable in character and strength, but contains no strong members of limestone or sandstone. If the support is removed, very probably it will subside. The Arkansas River flows across the salt district and Hutchinson is situated on the flood plain. Between the top soil, which is about 8 ft. thick, and the shale is 60 to 100 ft. of water-bearing sand and gravel. The process of removing salt, at least in the case of the earlier wells with which we are concerned, is as follows: An 8-in. hole is put down through the sand and gravel by means of a drive pipe, which is bedded in the shale. Prom the top of the shale, a 6411. hole is drilled through the shale, to, or nearly to, the bottom of the salt. Casing is put in to a depth of about 140 ft. to shut off a water-bearing layer in the shale.

Jan 1, 1927

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friede1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to B00 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By E. V. Potter, H. C. Lukens

THE volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.2 Both sets of data show a minimum solubility between 500° and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. There- fore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. APPARATUS AND METHOD The apparatus and method were essentially the same as those described in the previous work,1 as shown in Fig, I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transition points determined under such conditions were less accurate. ABSOLUTE SOLUBILITY Procedure and Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1946

By R. S. Christie

Reservoir pressure is the pressure at which a fluid is held in a state of equilibrium in a porous stratum. This pressure may be a result of the genesis of oil or gas and its subsequent migration into and through an adjacent porous stratum, or of hydraulic head. Reservoir pressure is an indication of the potential energy contained in the reservoir, and when it is known the engineer is in a position to use it to advantage in recovering and lifting the oil. It is important to know the pressures in any type of reservoir, but this knowledge is probably of greater value in a limestone reservoir, as at Hobbs, where producing rates or conditions may be more sensitive to changes in pressures. The Hobbs field is in east central Lea County, New Mexico. The discovery well was completed by the Midwest Refining C I. in 1928, but intensive development did not begin until after the completion by the Humble Oil and Refining Co. of No. 1-A Bowers in February, 1930. There are 143 producing wells on approximately 5500 acres. The field has not been defined to the northwest, but a projection of structural contours indicates that the productive area ultimately may cover 7500 acres. The producing horizon is the White or Crystalline lime of Permian age. The top of the lime is found at an average depth of 4000 ft. and the wells penetrate it an average distance of 200 ft. The main pay zone is an oolitic stratum about 25 ft. below the top, and varies from 2 to 15 ft. in thickness. Other porous or cavernous strata are found lower in the lime but have little saturation. The initial production varied from 100 to 25,000 bbl. per day, depending perhaps to some extent on the structural location but chiefly on the porosity of the pay. The initial gas-oil ratio varied from 325 to 16,000 cu. ft. per barrel. In wells where the top of the White lime was found below 350 ft. below sea level (Fig. 1)) the gas-oil ratio was usually less than 1500 cu. ft. per barrel, while in wells higher than 350 ft. below sea level, the ratio was usually above 2000 cu. ft. per barrel. The water table has been determined at about 620 ft. below sea level, by three wells on the west side of the field. With few exceptions, the wells have been completed with 7-in. casing cemented

Jan 1, 1932

By R. D. Barer, M. B. Bever

Age hardening alloys are quenched from the solution treatment to room temperature in order to retain a supersaturated solid solution. Some alloys age "naturally" in this condition but in most alloys aging is induced "artificially" by heating to intermediate temperatures. Cold working of the supersaturated solid solution accelerates the aging process and quenching strains have the same effect. The investigation reported here is a study of the progress of aging in specimens quenched directly from the solution treatment to various aging temperatures. This procedure reduces the temperature interval of quenching and the resulting quenching stresses. It also eliminates any changes which would take place in the undercooled sample at room temperature prior to aging at an elevated temperature. Isothermal aging is thus approached and its kinetics may be studied. An aluminum-copper and an aluminum-silicon alloy were chosen for this investigation. The aging mechanism of aluminum-copper alloys is complex while the aging of aluminum-silicon alloys is nearly ideal. As standards of comparison for the samples directly quenched to the aging temperature, specimens were also age hardened by the usual procedure in which solution treated samples are first quenched to room temperature and then reheated to the aging temperature. Review of Previous Work The mechanism of age hardening has been the subject of a controversy which has ranged from the theory of outright precipitation of an equilibrium phase to theories based on subtle changes occurring in the matrix prior to precipitation. A detailed critical review of the literature up to 1939 is available1 and contributions to the general theory of age hardening continue to be made.2,3 Age hardening, whatever its mechanism, involves the nucleation of a second phase within a supersaturated solid solution. Theoretical considerations4,5 indicate that the rate of nucleation reaches a maximum at an intermediate temperature below the temperature at which supersaturation sets in. Studies of precipitation at various subcritical temperatures have demonstrated that the largest property changes in a given time occur at such intermediate temperatures.6,7,8 The precipitation of a phase from supersaturated solid solution is accelerated by strains which may result from quenching or cold work. Phillips and Brick9 established that quenching strains are an essential condition for the age hardening of aluminum-copper alloys at room temperature, at least for aging periods of less than 30 days. They also found that on aging at 300°C the hardness increased faster and reached a higher maximum after quenching into water than after quenching directly to the aging temperatures. Fink and Smith10 observed preferential precipitation on slip bands and grain boundaries in aluminum-

Jan 1, 1950

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8.9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3-s in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6.9 The measure of internal friction adopted here, I/Q, is (p) X the logarithmic decrement, a measure used by some writers, and is also (I/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°°C. As shown in Fig. i, the internal friction increased by only a factor of 2 from room temperature to 300°°C., then by a factor of 100 during the next :too' interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction ~ e-HI/RT [I]

Jan 1, 1942

By M. R. Tek, F. H. Poettmann, M. L. Grove

The general problem of single-phase natural gas flow through porous media has been considered both by mathematical analysis and field experiments. Theoretical studies on the fluid dynamics of natural gas wells resulted in derivations of expressions which permit a ber-ter understanding of the flow mechanism for conditions under which Darcy's law is no longer valid. In applying these results to natural gas production and testing technology, special emphasis war placed on the study of low permeability, slowly stabilizing formations. These applications resulted in a method of predicting the performance coefficients of tight natural gas wells. The calculation of the performance coefficient requires the determination of the "test-index", pkh/µ, the drain- age radius, R, and the effective wellbore radius, rw. Methods for estimating these parameters from field data were also developed. Field data from 15 wells were collected and analyzed. The measured values of the performance coefficients were compared with the predicted values. This statistical evaluation gave a bias of 7.14 per cent and a standard deviation of 11.6 per cent. INTRODUCTION The performance of a natural gas well is determined by the physical properties of the reservoir rock, the extent and the geometry of the drainage area, the properties of the flowing fluid, and the conditions of pressure distribution within the drainage matrix. The relation between the quantity of gas delivered and the pressure drop within the reservoir is characteristic of the behavior of each well and is often referred to as the back-pressure behavior of the well. It is well established that for normal, single-phase gas wells the relationship between the gas delivery rates and the bottom-hole pressure take, in general, the form, Q = c(P3 8 -P2 1)n. ,.......(1) where C is the performance coefficient, and n is the exponent corresponding to the slope of the straight-line relationship between Q and (P2 s, — P2 l) plotted on logarithmic coordinates. The determination of a well's performance by the back-pressure behavior not only permits the production engineers to analyze many operating problems, but also provides necessary information useful and essential to predict the future development of the field.' Important engineering and production problems such as calculation of gas deliverability into a pipeline at a predetermined line pressure, design and analysis of gas-gathering lines, determinations of spacing and number of wells to be drilled during field development to meet future market or contract obligations, etc., all depend, at least in part, on the availability and use of reliable back-pressure curves.' In the past the behavior of gas wells was evaluated

Jan 1, 1958

By W. P. Blake

FORGING under the hydraulic press, which was introduced by Haswell in the year 1861, at the machine shops of the Imperial State Railway Company of Austria, has since been greatly improved, so that at the present time there are very few parts of machines which cannot be produced in this way, and at no greater cost than iron castings. The process is now used at Vienna chiefly for such parts of locomotives as cross-heads, link-bars, axle-box frames, etc., especially where the form is intricate, and there are many angles and projections. These objects weigh from 50 to 150 lb. or more, and it is claimed for them that they are not only much cheaper than ordinary forgings, but are much more regular in form and stronger. The results which Mr. Haswell has attained, after years of patient experimenting, were well shown in the Austrian Department of the Vienna Exhibition by a collection of the pressed objects in iron and steel, just as they left the moulds, with some of them cut asunder longitudinally and the surfaces etched, so as to show the internal structure or direction of the grain. Through the courtesy of Mr. Haswell and his son I saw the hydraulic presses in full operation at the works, drawing down large Bessemer ingots, cutting them up into blocks of convenient size, and forming various parts of locomotives. They have two large hydraulic presses in use; the largest, with a piston 24 inches diameter, gives 1200 tons pressure, and the second, with an 18-inch piston, gives 600 tons pressure. The pressure in the pumps is 600 atmospheres. The action is vertical ; the piston descends upon the work, and for forging ingots is armed with a hammer-like head. An ingot of No. 7 soft Bessemer steel, which was forged in my presence, weighed 2030 lbs. One end being placed upon the anvil, the piston is brought slowly down and crowded into the mass as if it were putty or dough, forcing it each way, but chiefly in the direction of the length of the ingot, this being the narrowest section of the anvil and hammer. The piston is then raised and the ingot is moved forward for a second squeeze, and so on, until the first half of the ingot has been reduced in thickness, when it is turned on edge and the operation is repeated. The ingot is then turned end for end and forged until the whole length has been re-

Jan 1, 1874

By R. H. Dourson, B. H. Sage, W. N. Lacey

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943