Search Documents

By R. M. Treco

THE thermal expansion of pure beryllium was first investigated by Hidnert and Sweeneyl in 1925 on a single cast specimen stated to be of 98.9 pct purity. A study of the coefficients of expansion by X-ray methods has recently been made by P. Gordon' on powder obtained from the Brush Beryllium Co. assaying 97 wt pct beryllium with about 2 wt pct oxygen as an impurity. The present work pertains to about the highest purity metal obtainable from the Brush Beryllium Co. This metal was in the form of lumps which were remelted and cast in a high-vacuum induction furnace. Expansion data in this paper deal with beryllium extruded into bars of rectangular cross-section 4x1/2 in. and the anisotropic expansivity of a large cast single crystal. Analysis of the cast metal after extrusion indicated a beryllium assay of 99.28 pct. Impurities were 0.170 pct Fe, 0.140 pct Al, 0.014 pct Mg, 0.086 pct Si, 0.020 pct Cu, 0.020 pct Mn, 0.007 pct Ni, 0.007 pct Ca, 0.080 pct C, 0.179 pct 0, (as BeO). Part I—Extruded Metal Thermal expansion measurements were obtained with a fused quartz-tube differential type dilatom-eter3 on specimens cut from the extruded sections in longitudinal and transverse directions. Specimens were machined to a diameter of 0.250 in. and a length of 3.000 in. One sample from each direction was vacuum annealed for 1 hr at 800°C. The dilatometer tube was placed in a vertical tube furnace having a uniform temperature zone which was twice the length of the sample. Average time for a complete thermal cycle to 500°C was 18 hr. Temperatures were observed with two chromel-alumel thermocouples attached to the sample about 1 M in. apart. The accuracy of temperature measure-ment was ± 0.25°C. An argon gas atmosphere sur-rounded the specimen to prevent oxidation of the beryllium. Samples were identified as shown in table I. Results - The original plan included measuring expansion up to 1000°C, but the first two runs on sample No. 5 showed that a permanent contraction occurred from

Jan 1, 1951

In an address delivered at Atlantic City, N. T., Dec. 5, 1918, M. L. Requa, General Director, Oil Division of the United States Fuel Administration, said: We face a new era with all its uncertainties. We have arrived at the period of reconstruction and are face to face with the problems concerning which we have so often speculated during the past four years. In all this reconstruction work the United States must bear an important part. We are looked upon to lead the way, to blaze the trail and our actions will have a profound influence upon the rest of the world. If we are to succeed, even in part, we must not be ashamed to practise economy; we must not despise the clay of small things; the little savings; we must have the closest cooperation between Government and industry. Just as truly do we need civic awakening. All that we have ever fought for, the liberty of the world, is comprehended in the ballot; and yet how lightly we have held this great privilege! We need, if we are to reap in full the benefits of the past 18 mo., an awakened civic consciousness; a jealous guarding of government; a resolution that we will, each and all, perform to the full the duties imposed upon us by Democracy; that we will perform more completely the obligations resting upon us as citizens. During the war, industry, through sane cooperation and intelligent effort, has accomplished results possible of attainment in no other way. Government and industry have worked hand in hand and pointed the way o to future activities which, if realized, can but be most highly beneficial to all. If Government and industry are to fulfill their respective duties satisfactorily, it is obvious that there should be complete mutual confidence. Industry must not attempt to "put something over"-and Government must treat with industry upon the high plane that has characterized the public utterances of the President during the war. The individual who cannot conform to these high ideals should have no place in industry, and equally no place in Government. If the dignified and broad princi-

Jan 2, 1919

By B. L. Sackett

In a general way, the situation in copper smelting is quite similar to that of lead smelting. In other words, the introduction and successful flotation of copper ores has tended to decrease greatly the tonnage to be handled by the smelter and therefore has resulted in curtailed smelter operation. However, copper production has increased rather than decreased. The general effect of flotation has been to decrease the number of furnaces operating, but it has also increased to a considerable extent the difficulties in handling the material, just as was outlined in the case of lead smelting. In copper smelting, the flotation concentrates must be roasted and prepared for the reverberatory furnace. Handling Flotation Concentrates The handling of copper flotation concentrate, which is more or less wet and mucky, is more difficult than was the handling of the old gravity concentrate. Also, the roasting of the concentrate and the handling of the calcine produced is more difficult. That is mainly because the material is extremely fine and the tendency to higher dust losses is greatly increased. The draft in the roasting furnaces must be kept as low as possible, and the feeding of the calcine into the reverberatory furnace must be done carefully, so that dust losses may be kept at a minimum. Transition Stages oF Concentration and Smelting The general process through which the copper smelter has gone as a result of flotation has been somewhat as follows: In the relatively old days, when copper ores of low grade were first treated, a large number of furnaces were required, and naturally comparatively poor recoveries were made. Also, the profits on low-grade ores were small and the handling of those ores was possible only because of the large tonnages. Then came gravity concentration, which was a great improvement but which only incompletely removed the gangue material, the insoluble and the iron, from the copper ore, and made comparatively poor copper recoveries. This still left a considerable amount of insoluble and iron, as well as the copper itself, to be treated at the smelter.

Jan 1, 1928

By A. R. Troiano, W. J. Barnett

The existence of a grain size stabilization effect on martensitic type reactions as shown by Scheill in an iron-29 pct nickel alloy and by Troiano and Tokich2 in cobalt prompted a review of other martensitic reactions to determine if this stabilization effect is characteristic of all martensite type reactions. Preliminary work has shown this effect to be present both in the gamma —+ epsilon transformation in an iron-20 pct manganese alloy and the martensite transformation of SAE 4140 and 3 pct Cr-O.40 pct steels. No appreciable effect was found in an SAE 2340 steel. The M, temperature for the gamma —+ epsilon transformation was lowered from 380°F to about room temperature by varying the annealing treatment following cold work as shown in Table I. The effect of austenitic grain size on the M, of three steels is shown in Table 2. M, was deter- mined by the conventional quench-temper method of Greninger and Troiano. In a single crystal the change in external shape concomitant with the homogeneous shear mechanism of the martensite transformation can take place unhindered. In a polycrystalline specimen a restraint of these changes must occur at the grain boundaries. Therefore, the smaller the grain size the greater the shear strain energy necessary for the formation of a martensite crystal. The degree of lowering of M, due to the reduction of grain size is much greater when the change in crystal structure involves only a small energy change, such as face-centered cubic —+ close packed hexagonal (that is, CO and Fe-20 pct manganese alloy). The maximum lowering of M, observed in the steels investigated was 50°F with a change in the ASTM austenitic grain size of 1-2 to 8-9. In comparison, the crystal structure change face-centered cubic —+ body-centered tetragonal involves a considerable energy change. There is little doubt that with much finer grain sizes the increased grain boundary restraint would greatly enhance this stabilization effect. The implications of this phenomenon are multifold. Undoubtedly. under certain conditions it offers a method of stabilizing high temperature phases for room temperature

Jan 1, 1949

By Walter O. Snelling

Continuation of the discussion of the paper of WaltER o. SnelLIng, presented at the New York and San Francisco meetings, February and September, 1915, respectively, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704 and Trans., li, pp. 657 to 671. A. C. McLaUghlin, San Francisco, Ca1.—It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out in the last 25 years. If his end products are what they seem to be, he has made. a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750" F, and pressure of 750 lb. per square inch. William A. WillIams, San francisco, Ca1.—What metal did you use, Mr. McLaughlin? A. C. McLauGHILIN.—Ordinaly seamless tubing, extra strong. William A. Williams.—Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Bittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150" C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. Best, New York, N. Y.—What is the difference between the Rittman and the Snelling process or system? William A. Williams.—he fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By Merton C. Flemings, Harold D. Brody

Analyses that include diffusion of solute in the solid phase are formulated to describe solute redistribution in dendritic solidification of metallic alloys. The analyses are based on conditions that include negligible undercooling before nucleation of solid phases, negligible increase of solute in advance of the tips of growing dendrites, complete diffusion within the liquid over distances the order of dendrite spacings, and a plate-like dendrite morphology. The classical nonequilibrium freezing equation, Cs = kCo(I - fS)k-l accurately describes solute redistribution between dendrite arms for the solidification processes considered, provided diffusion in the solid is negligible. To account for the effect of diffusion in the solid, an analytic expression is given which is similar inform to the classical expression. 172 addition, a numerical-analysis procedure is etnployed to examine in more detail the effect of diffusion both during and after solidification. The analyses are intended for application to solidification of castings and ingots to describe a) final solute distribution after solidification and cooling to room temperature (microsegregation) and b) local fraction solid as a function of ternperatcre within the solidifying casting or ingol. SOLUTE redistribution in cellular and dendritic solidification has been discussed quantitatively in recent papers'-3 and in a series of earlier work.4-6 However, none of the analyses developed have permitted close correlation of theory with final solute distribution (microsegregation) observed in castings and ingots. In this paper, discussion is given of approximations which may reasonably be made in mathematical treatment of microsegregation, and analyses are presented based on these approximations. Numerical results are given for Al-Cu alloys. In a second paper the analyses will be compared with exeriment.7 CLASSICAL ANALYSIS The classical quantitative treatment of solute redistribution within a closed "volume element" has been derived repeatedly, for example by Gulliver,4 Scheil,' and Pfann.' This "classical nonequilibrium solidification equation" is written for constant partition ratio: where Cs = interface composition of the solid when the weight-fraction solid within the "volume element" is fs (weight fraction, wt pct); k = equilibrium partition ratio; Co = initial alloy composition within the volume element (weight fraction, wt pct). Assumptions of Eq. [11 are: 1) There is negligible undercooling before nuclea-tion, or from curvature or kinetic effects. 2) There is no mass flow in or out of the volume

Jan 1, 1967

By Oscar A. Glaeser

THE mine and plant of the United Verde Copper Co., located in Yav-api County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level. The underground mining operations extend from the 300 to the 3000-ft. level. There are about 45 stopes in active operation on the 17 levels

Jan 1, 1929

By W. R. Ingalls

In choosing the unusual title given to this paper, in which the term "cyclic " might be substituted for "intermittent," my idea has been simply in respect of precision. We might say old method vs. new method, but that antithesis implies something of substitution that has not occurred and perhaps is not in sight. We may say horizontal retorts vs. vertical, but none of the older retorts are truly horizontal, and there are three different types of vertical retorts. Other complexities might be suggested. There is, however, a broad distinction between distilling that is accomplished in a periodic cycle, generally daily; and distilling that is accomplished continuously, irrespective of whether it be done in the vertical retorts of the New Jersey process or in the retorts of the Trollhät-tan process. In offering a summary of the present state of the art with the intermittent process, I shall not have any idea of exemplifying it through descriptions of any single plants, but shall rather divide among the main steps of the process and outline what is best developed among them. In pursuing this thought, it will manifestly be impossible to make a composition that will exemplify the acme of good practice, for the latter will always be a function of the cost of labor, fuel, etc., which are widely variable. As of 1929, in respect of labor we might generalize the average plant wage in the Pittsburgh-Wheeling district of the United States at $5 per day; in Oklahoma at $3; in Great Britain at $3; in Germany at $1.75-$2; in Belgium and France at $1. With high labor costs the metallurgist will naturally use means of the nature of mechanization that with low labor would be uneconomical when capital charges are taken into account. Nor may we from records of performance safely make positive deductions in respect of the efficiency of different types of furnaces unless they have been tested comparatively under identical conditions in the same works. We shall find gas-fired regenerative furnaces showing coal consumption from 1.2 tons down to 0.7 per ton of roasted ore, which may be ascribable to difference in the thermal value of the coal that is used or to differences in proportions of the parts of the furnace, which is something quite distinct from the principle of the furnace. Thus, we have

Jan 1, 1937

By D. J. McAdam, G. W. Geil, R. W. Mebs

AS shown in previous papers by the authors 9-l7† the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses.‡ A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers, 9-I8 the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress, § namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the influence of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture, of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals "should" behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or "plastic fracture " and a "brittle fracture." In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture. In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1947

By C.A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth' noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1943

By C. A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth' noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1943

By R. J. Sullivan

DURING the past twelve months the Loudon pool of the Eastern Interior Coal Basin has become established as one of the two largest discoveries since the revival of exploitation in the Illinois region and now occupies a position among the important pools of the United States. On Aug. 1, 1939, production averaged 54,000 bbl. per day from 990 wells, having accumulated a total of 10,305,000 bbl. Its very active develop-ment promises to continue for fully another year. It is the site of one of the industry's most singular large-scale gas-injection programs. LOCATION AND RESERVOIR CHARACTERISTICS At present the pool embraces an area 15 miles long by 3 ½ miles wide in eastern Fayette County, along the western rim of the now well-known Illinois Basin's deeper part, through townships 6, 7 and 8 north and ranges 2 and 3 east of the Third Meridian. It is the northernmost, and most prominent, productive structure of a group extending over a 50-mile trend southward to the Dix pool of Jefferson County. Three horizons have been proved to carry production-namely, the Weiler sandstone at 1390 ft., the Paint Creek sand at 1460 ft. and the Benoist or Bethel, at 1500 ft. Geologically, they fall in the Chester series of the upper Mississippian system, where much of Illinois' early-day oil was found, having been laid down in shallow off-shore waters as a part of the vast delta deposit underlying central Illinois and parts of Indiana and Kentucky. As a result of this type of sedimentation, followed by repeated uplifts and warping along an anticlinal axis, differ-ential deposition of sands and shales contributing to great irregularity took place. This is further reflected by wide variations in permeability, porosity and thickness of all the sands and, accordingly, in the producing characteristics of wells. Permeabilities range as high as 550 millidarcies, with the average commonly lying between 60 and 100. For the three pay horizons the mean porosity is 18 per cent, at a calculated water saturation of roughly 30 per cent. The Weiler sand has an average thickness of 25 ft., the Benoist of about 23 ft. and the Paint Creek of approximately 18 ft. Of these three productive formations the Benoist

Jan 1, 1940

By R. E. Reed, C. J. McHargue

Single crystals of aluminurn were reduced 90 pct in diameter by extrusion at 296" and 77°K. The resultant double fiber texture had a strong (111) component with a weak (001) component. The relative anzounts of these components varied with starting orientation. Decreasing the Lemperatuve of defovtnation increased the amount of (001) texture component in crystals with inilia1 orientations near (111). The starting orientation and temperature of deformation strongly affected the morphology of the (001) component. The effects of orientation and Lemperatuve upon the distribution of the (001 ) texture component in extruded aluminum single crystals were rationalized on the basis of deformation band formation and interaction. MANY papers since the early 1920s have discussed the occurrence of the double fiber texture (111) + (001) in wires and rods of deformed fcc metals. Aside from the reporting of experimental results for the various metals under a variety of fabrication conditions, emphasis has been placed on two related problems. One problem deals with the prediction of ideal end orientations based on the glide systems and flow directions. The other problem seeks the reason why different amounts of each component may be produced by the same fabrication schedule for metals apparently having the same deformation systems. Some of the difficulties in developing a satisfactory explanation have their origin in the experiments themselves. One mistake has often been the assumption of an initially randomly oriented specimen or complete ignorance of effects of starting orientation. Recent studies by Grewen and Wassermann,1 Cullity and co-workers,2' and McHargue4 have shown that the initial orientation may be the most important factor in determining the final orientation. Hence only limited comparisons of data from different studies can be made unless all conditions of the initial material are specified. Another question has been the nature of the (001) component. Hibbards suggested that any (001) present was the result of re crystallization during fabrication. Although Fleischer6 found no (001) texture in aluminum swaged at room temperature, and Dayal 7 found that component to disappear at very high reductions, a double fiber texture has usually been reported for aluminum. Vandermeer and McHargue showed that, while some (001) in aluminum may be the result of recrystallization, much of this component has its origin in the deformation process. Ahlborn and Wassermanng found the (001) component in silver deformed at low temperature not to be the product of recrystallization.

Jan 1, 1968

By L. E. Young

THE progress of mineral industry education will be limited to the period prior to World War II and will be considered as primarily a division of engineering education. Its relation to progress in the mineral industry and to the activities of the American Institute of Mining and Metallurgical Engineers will be emphasized. The history of mineral industry education has been recorded most completely and authoritatively by Dr. T. T. Read in his recent volume in the Seeley W. Mudd Series of American Institute of Mining and Metallurgical Engineers publications, entitled, The Development of Mineral Industry Education in the United States. Therefore, most of the historical details will be omitted from the discussion and an effort will be made to point out significant developments and to analyze trends. INTRODUCTORY STATEMENT AND SIGNIFICANT POINTS IN PROGRESS Among the significant points in the development of mineral industry education in the United States since 1871, the following deserve particular mention: I. The number of institutions offering undergraduate instruction has increased, particularly during the years 1890 to 1925; the number of students enrolled in undergraduate study has increased greatly, largely on account of the development of courses in petroleum engineering and increasing interest in metallurgy. 2. The selection of students to be admitted to undergraduate courses has been improved through the advisement, counseling, and guidance programs sponsored by the Engineers' Council for Professional Development. 3. Improved instruction methods and the training of the teaching staff have been promoted by the educational institutions themselves, but with the most effective stimulus and guidance of the American Society for Engineering Education and the Engineers' Council for Professional Development. 4. The accrediting of undergraduate curricula through the Engineers' Council for Professional Development, considering both qualitative and quantitative criteria, has done much to improve standards of instruction in engineering education for the mineral industry. 5. Undergraduate curricula and courses are revised currently to meet the needs of the American mineral industry. New curricula are developed currently to permit specialization in technical fields, particularly in the fourth year of undergraduate work. 6. There has been a strengthening of the fundamental courses in mathematics, physics, mechanics, and chemistry, and at the same time these courses are being adapted to the most recent developments in the industry, including metallurgy, geophysics, petroleum engineering, petroleum technology, ceramics and so forth. 7. There has been continuing improvement in plant and laboratory facilities of the educational institutions.

Jan 1, 1947

By S. J. Matas, R. F. Hehemann

The existence of two distinct forms of bainite—upper and lower bainite—in hypoeutectoid steels is confirmed by a systematic study of the structure of the product resulting from this mode of austenite decomposition. The transition between these two forms occurs at about 650° F regardless of the alloy content of the steel and their structural differences can be interpreted in terms of the kinetics of carbide precipitation from supersaturated ferrite. In the past few years, a renewed interest has been displayed in the kinetics and mechanism of the bainite reaction in steels. Several rather divergent models for the transformation mechanism have evolved from these studies,'-' however, it is difficult to evaluate these models critically on the basis of the existing experimental data. In particular, a more detailed knowledge of the structure of bainite should be helpful in providing a framework for the construction of an appropriate model. Metallographic studies7-l4 have led to a recognition of at least two distinct forms of bainite—frequently termed upper and lower bainite. Although the morphology of bainite changes with reaction tem- perature, there appears to be a relatively sharp transition between the two forms. This occurs in a narrow temperature range near 650° F. Transformation at temperatures below about 650° F results in the presence within the bainite of small plates of carbides oriented at an angle of 60 deg with respect to the direction of growth of the plate, while at higher temperatures carbides are oriented parallel to the growth direction. There is no generally accepted view regarding the significance of this structural transition. Some authors feel that carbides precipitate from austenite at all reaction temperatures1' while others claim, at least for low-temperature bainite, that carbides precipitate from supersaturated ferrite.14.15 It was recognized many years ago that the nature of the carbide in bainite depends on the reaction temperature. The carbide hase in upper bainite is unmistakenly cementite.16-19 The exact nature of the carbide in low-temperature bainite is less certain. Magnetic measurements of lower bainite reveal no cementite Curie point21'22 and dilatometric studiesz0 produce total expansions which are larger than those predicted on the basis of a ferrite-plus cementite structure. These effects have been attributed to the

Jan 1, 1962

By N. A. Gjostein

The self-diffusion coefficient D, for a surface near the (100) plane in copper was determined by means of the Mullins theory of thermal grooving, and was found to obey the Arrhenius relationship, and Do = 6.5 x 10' sq cm per sec. Suppression of surface diffusion by chemisorbed impurities encounters difliculties as a satisfactory explanation for the large Q, and Do. Instead, a model is presented which indicates that Q,, as determined by a mass-transport technique, may involve both the energy needed to form an adsorbed atom from a ledge in the surface as well as that for the movement of the adsorbed atom.; LITERATURE reviews1-3 indicate that the mechanism of self-diffusion on metal surfaces is not clearly understood. The lack of experimental data on the temperature variation of the surface self-diffusion coefficient DJ has contributed greatly to this situation. Radioactive tracer techniques4-rn have been used to measure Ds, but for many years only Nicker-son and Parker8 had determined (for polycrystalline silver) an activation energy B, and a frequency factor Do for the surface self-diffusion process. Even in this case, a mechanism could not be clearly inferred because it was suspeted7 that a contribution from volume diffusion was not taken into account by the investigators. Some later work by Li and parkere on polycrystalline gold, in which they obtained essentially the same results as for silver and in which volume diffusion could be accounted for, seems to invalidate this criticism. In 1957, Mullins10'11 developed the theory for the thermal grooving process. This advance has opened a new and promising technique for measuring the surface self-diffusion coefficient Ds. Recognizing that a thermal groove may form by several different mass transport processes, Mullins first consideredlo the cases where a) the groove forms by evaporation and condensation or b) by diffusion along the groove surface, in either case, in a system where a metal surface is in contact with only its dilute vapor phase. In a later paper," he extended the treatment to cases where the groove forms by volume diffusion into c) the solid phase or d) by mass transport through a passive gaseous phase at 1 atm pressure. The time dependence of the groove dimensions and the shape of the groove profiles predicted by Mullins' treat-

Jan 1, 1962

By D. J. McAdam

As shown in three recent papers by the author,6,7,8 in two papers by McAdam and Mebs,9,10 and in a paper by McAdam, Mebs, and Geil,11 the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stresses? as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strengths nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. Ib and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses, with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. Ib shows stress combinations with S2 equal to Sa. The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. Ia shows stress combinations with Ss equal to Sl. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-11 In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1944

By G. Sachs, L. J. Ebert, W. F. Brown

IT is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to the same strength level (i.e., the same tensile strength in a conventional tensile test), However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features-the high speed, the notch, and the bending-the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels3,4,7,8 have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests, In an attempt to analyze the fundamental nature of this test,8 it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom, The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension, This triaxial stress state occurs at a point in the interior of the notch specimen, It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present, This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors, This is contrary to the behavior of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1946

By F. N. Rhines

I. An Outline of the Theory of the Sintering of Pure Metal Powders SINTERING may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, q, 28, 34, 38, 50, 52, 54 a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." II. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A. The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature.28 Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light contact,"' as do those of many other substances, including nickel." b. Upon compression the strength of the bond is increased progressively.28 There is a limit of pressure

Jan 1, 1946

By H. R. Collins

The purpose of pulverizing coal before burning it is to make available every heat unit it contains. Machinery has been developed which will pulverize coal in one operation, delivering it to bins in front of the furnaces at an expenditure of about 17 hp.-hr. per ton, in a medium-sized plant. The cost of the operation depends upon the amount of moisture that must be expelled before pulverizing, the cost of labor, and the cost of coal delivered at the plant. At a small plant, requiring a pulverizer with a capacity of only 1/2 ton per hour, the cost per ton pulverized will naturally be greater than at a plant requiring the largest pulverizer, with a capacity of 7 tons per hour. :The first step is to reduce large lumps to a size suitable for drying uniformly, before passing to the pulverizing mills; this is done in rolls, at a single pass. The second step is the elimination of moisture, in order to facilitate pulverizing to great fineness, while also increasing the heating effect and the temperature attainable when the coal is burned. There are other mechanical advantages in the handling of dried coal. Driers are now manufactured which are able to eliminate moisture without distilling any of the volatile combustible matter in the coal; they are fired by hand or with pulverized fuel. The heat first surrounds the shell of the drier, being confined within a chamber where complete combustion takes place; the heated gases are then led through a duct to the discharge end of the drier and enter the inside of the shell at a temperature not exceeding 300" F. This temperature is maintained by the operator and is indicated by a pyrometer. Volatile combustible matter is not likely to be distilled until the temperature rises above 400" F. On discharging from the drier, the coal is usually passed over a magnetic separator in order to prevent pieces of iron from going to the pulverizer. Two types are used: a magnetic pulley which automatically discharges its collection of iron, and a lifting type, from which the iron is removed by hand when convenient. In the operation of pulverizing, the coal should preferably be reduced until 95 per cent. will pass through a 100-mesh and 70 per cent. through a 300-mesh sieve. Such a product is obviously an almost impalpable powder.

Jan 1, 1920