Search Documents

THE CHAIRMAN (G. C. STONE, New York, N. Y.).-It is a matter of history that the smelting of zinc ore in, a reverberatory furnace was the first process used in this country for making oxide of zinc, and it was abandoned for three reasons: it was very expensive, the recovery was, very poor, and the color of the oxide was worse. It is probable, however, that the Anaconda company is working in a totally different way. While Mr. Ingalls does not say so, my own suspicion is that they are using coal-dust firing, very much as they do in the copper furnaces, and by that method there is much more chance of getting good recovery.

Jan 1, 1918

Jan 1, 1951

By Bernard Amadei, Richard E. Goodman

A medium is anisotropic if its properties vary with direction. This is the general characteristic of many rocks, for example, schists, slates, gneisses, phyllites and other metamorphic rocks. Bedded and regularly jointed rocks also display anisotropic behavior. This paper is concerned with the influence of rock anisotropy on in-situ stress measurements. It is limited to stress measurements by overcoring techniques for which strains and displacements are recorded either on the walls of a pilot hole at the end of one or several boreholes or within instrumented solid or hollow inclusions perfectly bonded to the surface of the pilot hole. The rock is described as homogeneous, continuous, anisotropic and linearly elastic. The following questions are answered with special emphasis on rocks that can be classed as transversely isotropic or orthotropic: the number of independent measurements obtainable in a single borehole; the number of boreholes required to determine the in-situ stress field; the influence of rock anisotropy on these numbers; the influence of the anisotropy type and the error involved by neglecting rock anisotropy.

Jan 1, 1982

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Engineer, 43, married. Sixteen years' experience mining. Desires permanent position mine superintendent. Broad knowledge all types underground mining and shaft sinking. Construction and milling experience. Prefer North American continent but will accept foreign. Presently located Australia but available May 1, 1953. M-706. POSITIONS OPEN Mining Engineer with broad exploration experience, young, single status, and must be in excellent physical condition, as nature of work will be under very primitive conditions. Salary about 25 pct more than applicants last salary rate plus travel expenses and living allowance. Duration until July 1953. Location, Burma. Y7498.

Jan 1, 1952

By A. R. Hendrickson, C. F. Smith

Hydrofluoric-hydrochloric acid mixtures have been successfully used to stimulate sandstone reservoirs for a number of years. Hydrofluoric acid (HF) has a specific reactivity with silica which makes it more effective than HCl for use in sandstone. Kinetics of the reactions of HF have been studied to determine the related effects of reservoir composition, temperature, acid concentration and pressure on the spending rate of HF. Secondary effects from by-product formation are noted and described. Predictions are made concerning the improvement in productivity resulting from HF treatment of skin damage. The kinetic order of HF reaction in sandstone was experimentally determined to be first order, i.e., the reaction rate is proportional to concentration. HF reacts faster on calcite than on clay, which, in turn, is faster than the reaction rate of HF on sand. Static conditions retard the HF reaction rate. As HF is forced into cores, there is a temporary reduction as a function of flow rate and acid concentration. Extensive deposition of calcium fluoride in acidized cores was not observed. Although some CaF, was defected, it was not considered a major source of damage in cores containing moderate amounts of carbonate. Other fluosilicates could be potentially more dangerous than CaF, in reducing permeabiliry. INTRODUCTION Hydrofluoric acid has been widely used in stimulation treatments since 1935, when mud acid was introduced to the petroleum industry. Originally, this hydrochloric-hydrofluoric acid mixture was intended to remove mud filter cake, but it has since been successfully applied to many other oilfield problems. Mud acid treatments have been unusually successful in sandstone reservoirs where hydrochloric acid is unreactive due to a lack of enough calcite in the formation. The relatively small amount of hydrofluoric acid present (2.1 per cent) reacts with sand grains, clays and traces of calcite which are generally present in sandstone reservoirs. Since hydrofluoric acid (HF) is the key to mud acid success, this research effort has been dedicated to gaining a more thorough understanding of the basic chemical and physical principles involved as HF reacts. Hydrofluoric acid's reactivity with silica makes it unique in application. Other mineral acids such as hydrochloric, sulfuric or nitric are unreactive with most silicious materials which comprise sandstone formations. A typical sandstone reservoir may contain 50 to 85 per cent silicon dioxide, more commonly called sand or quartz. Hydrofluoric acid reacts as follows: 4HF + SiO2 + SiFO + 2H2O The silicon tetrafluoride (SiF,) is a soluble gas, in some ways similar to CO2, and is capable of undergoing further reaction when held in solution by pressure. These reactions will be considered in detail later. Kinetics of the reactions of HF have been studied to determine the effect of reservoir composition, temperature and pressure on the spending of the acid. Secondary effects from by-product formation have been noted and described. The individual reactions of HF on quartz, glass and clay are reported. Mathematical correlations have been drawn, then applied to studies of HF spending in cores obtained from actual producing sandstone formations. The research reported herein is only the beginning of a continuing approach to better understanding and use of HF in petroleum reservoirs. THEORY AND DEFINITIONS Through the years, a concentrated effort has been made to understand the effects of many variables on hydrochloric acid (HCI) spending in limestone. Hendrickson el al., have given mathematical relationships for HC1 reactions which made possible the engineered approach to acidizing. The same variables—temperature, acid concentration, formation composition, pressure and permeability-porosity relationships—which affect HC1 behavior in limestone also govern HF behavior in sandstone. Insoluble by-products of HF reaction have been isolated and identified. Their effect on fluid flow has been measured under varying conditions in an attempt to evaluate the extent of possible damage and means of eliminating it. In general, HF follows the same reaction paths as HCI. It will react with limestone and dolomite with speed and ease. Thin sections of acidized cores show the reaction of HF with limestone or calcite faster than its reaction with either clay or sand. When HF reacts with calcite (CaCO,), theoretically, calcium fluoride (CaF2) is precipitated, and has been blamed as a major cause of reduced permeability. On the other hand, pH and pressure such as that encountered in an underground formation under acid treatment definitely retard CaF2 formation,' so the whole question of CaF, deposition in wells is a subject for study.

Jan 1, 1966

MIXED emotions were produced by the announcement that the buildup of weapons will be stretched out till mid-1954 instead of the previous 1953 deadline. Reason: government assistance programs will be tougher to get but there will be easement in materials allocations. Earlier in February, DPA had announced that tightening up on regulations governing rapid tax -amortization would become effective March 1. In the future, DPA will have to certify amortization contracts for all construction and permanent installations costing more than $100,000. This action was necessary according to DPA's James F. King, so that new industrial expansions already approved could be assessed in the light of the changing critical mineral picture. When DMPA inherited the backlog of government assistance, requests from DMA, it moved in fast. The results of DMPA's work is described in the article on p. 351 by James K. Richardson; The speed with which these requests were approved and the lengthening of the military program have made a reappraisal of the critical mineral list necessary. It looks as though the consumer industries will be getting more metal soon and, led by steel, there is an industry push toward the abandonment of CMP. Relaxing of materials controls appears imminent but discontinuing CMP is in the "let's talk this thing over" stage.

Jan 1, 1952

By A. L. Mincher, W. F. Sheely

Mechanical properties of columbium have been studied over the temperature range of -196 to 1093oC. The decreased strengthening influence of cold-work at temperatures below ambient has been interpreted in terms of the Peierls-Nabarro effect. Maxima in the rate of strain hardening observed during tensile testing in the range 250-600°C. have been correlated with interstitial impurities to indicate the temperature ranges at which carbon, oxygen, and nitrogen, respectively, are responsible for strain aging. THE growing need for structural materials for use above the useful service temperatures of the iron-, nickel-, or cobalt-base alloys has caused the refractory metals to be considered as potential engineering materials. These metals, which include columbium, tantalum, molybdenum, and tungsten, are called refractory because the lowest melting point among them,that of columbium, is about 1000°C higher than the average melting temperatures of conventional high-temperature alloys. They are all body-centered cubic transition metals and, as such, their mechanical properties have basic characteristics which distinguish them from the face-centered cubic metals. For example, all show a much steeper rise in strength with decreasing temperature below room temperature than do the face-centered cubic metals, and their mechanical properties are strongly influenced by interstitially dissolved impurities. In order that these new metals may be used efficiently, it is necessary that their characteristics of behavior be fully known. In this paper, the mechanical properties of columbium will be examined over a wide range of temperatures. In particular, the influences of cold-work and individual species of interstitial impurity atoms on mechanical properties will be described, and basic mechanisms which may control the observed characteristics will be explored. EXPERIMENTAL The material used in this investigation was Union Carbide Metals Co. columbium roundels consolidated to four 4-in. diam ingots, three by consumable-electrode arc melting and one ingot by electron beam melting. Impurity contents of the ingots and methods of ingot conversion and treatment are summarized in Table I. The only metallic impurity occurring in any significant quantity was tantalum at about 0.1 pct. Iron, silicon, titanium, and zirconium were each less than 0.015 pct; boron was 1 ppm or less. This should have no appreciable influence on properties. The electron beam melted material, being the purest, will be used as the basis for comparison in the discussions to follow. Tensile tests were conducted from-196 to 1093oC, on both cold-worked and fully recrystallized arc-melted and electron-beam melted columbium using standard 1/4-in. diam, 1-in. long gage length test specimens. A strain-rate of 0.005 in. per in. per min was employed until the 0.2 pct yield strength was achieved and then the strain-rate was increased to 0.05 in. per in. per min for the balance of the test. Samples were protected in an inert atmosphere at tests above 300°C. The tensile properties obtained on the electron-beam melted columbium, E, in both the cold-swaged and recrystallized conditions are given in Fig. 1. The yield strength data of Dyson, et al.,' obtained on recrystallized electron beam melted columbium and the tensile strength data reported by Tottle2 on powder metallurgy columbium are included in Fig. 1. The material used by Tottle had been purified by vacuum sintering. There is excellent agreement between Dyson's data and those obtained in the present investigation. The tensile strengths obtained by Tottle were slightly greater than those obtained in this investigation on electron-beam melted columbium but varied with temperature in a similar manner. Tottle's data showed a maximum in tensile strength near 500°C, as did our data on electron-beam melted material, and also showed a small maximum at 300°C. The significance of these maxima will become evident later in the discussion. The tensile properties of cold-swaged and recrys-tallized arc melted columbium are plotted in Fig. 2. It was found that the properties of the recrystallized arc-melted columbium from all three heats showed very close agreement except at temperatures between about 500" and 800°C. A reason for this range of disagreement will be suggested in the discussion. The generally good agreement, however, attests to the ability of cold-working and subsequent recrystal-lization to erase the effects of the three different primary breakdown procedures and to produce nearly equivalent structures in the samples derived from the three different heats. wesse13 reported tensile data on columbium having interstitial impurity contents between those of the

Jan 1, 1962

By S. Nakajima, H. Okazaki

Quantitatiue studies of the deformation texture in drawn tungsten wives were made by the X-vay dif-fractottletetr. Experimental results show that the diffraction Intensities are equal to tilose pvedicted from the (1 10). fiber lexlure but the angxla), spreads of. diffraction peaks in the pole distribution curres are different for different diffraction planes and directions. For this reason a modified (110) fiber lextuve model, in which a kind of anisotropy is assumed, is proposed to explain the results. According to this model the poles lying on a line directing front the (110) to the (110) poles in the (1 10) standard stereograpllic projection should show spreads which are different from those lyitlg on a line directing from the (001) to the (001) poles, which is confirmed by the experiments. The anisolvopy and the spveads of the pole positions are large at the outer part of the wires and decrease gradually lowards the inside of the wire. The possibilily of occurrence of such anisolropy in irrelals with fcc stvuctures is discltssed. THE deformation texture of drawn tungsten wires has been assumed by different investigators to be the simple ( 110) fiber texture.' Recently, however, Leber2,3 has shown that a swaged tungsten rod has a cylindrical texture. It changes gradually to the (110) fiber texture by drawing through dies. However, even after drawing to 0.25 mm in diam, the cylindrical texture can still be found in wires together with the (110) fiber texture. This was deduced from the pole figures obtained from the longitudinal section of these wires. Use was made also of quantitative measurements of the pole distribution curves. Leber stated that the angular spread of the pole distribution curves (henceforward called dispersions) are quite different for (400) 45 deg and (400) 90 deg: the former is always larger than the latter. This inequality is accompanied by deviations of the diffraction intensities from the theoretical values for the ( 110) fiber texture. Bhandary and cullity4 have reported similar results on iron wire and explained them by assuming a cylindrical texture. Both Leber3 and Bhandary4 used only the results of the (400) reflection for the determination of the dispersion. The pole figures found by Leber3 and by Rieck5 are largely different. The model given by Leber to explain the effects is in the authors' opinion in some respects unsatisfactory, especially if one looks at other than the (400) reflections. Intensities and dispersions of diffraction peaks are conclusive factors for the determination of the fine structure in wire textures. For this reason we studied them extensively to come to a model which is more suitable to fit the facts. In the following, after giving the experimental set-up, we report about measurements of X-ray diffraction on drawn tungsten wires. Different models to describe the experimental results will be discussed. EXPERIMENTAL GO-SiO2-A12O3 doped tungsten wires drawn to 0.18 mm in diam were used for the measurements. The wires were chemically etched to various diameters down to 0.03 mm. Measurements were carried out for the different wires in order to determine the dependence of the texture on the radius. The wires were cut to pieces of 10 mm length and fixed with paste closely against each other on a flat, polished glass plate. Parallelism of the wires with the surface of the glass plate should be adequate. For the diffraction studies three different X-ray sources were applied, respectively, giving the CuK,, FeK,, and FeKp emission. The measurements were carried out with a diffrac-tometer with a GM counter. The latter was fixed to a certain diffraction angle 20hkl and the diffraction intensity was recorded as a function of the angle of rotation of the specimen around the axis, lying in the specimen surface and perpendicular to the wire axis, as shown in Fig. 1. Measurements were also done with the detector at angles slightly deviating from the diffraction maxima The measured intensities in this case were taken to be equal to the background level. The deviations were chosen as small as possible but large enough to eliminate the influence of the diffraction maxima. The useful range of the rotation angle x of the specimen is generally limited by the wavelength of the X-rays. We have: where and cp is the angle between the wire axis and the normal of the diffraction plane. Intensity measurements were made to find the necessary corrections for counting loss of the GM counter and for distortion resulting from such effects as absorption of X-rays and from inclination of the reflection plane under study with respect to the surface of the specimen. The counting loss was esti-

Jan 1, 1968

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959

By Robert F. Shurtz, William J. Verner

Three basic questions must be answered by an engineer performing an economic analysis of a mineral property: (1) How much can the company afford to pay for the property; (2) At what rate should the property be mined; (3) What will be the return on the investment. These questions often defy reasonable analysis, because at the point in time at which they must be answered little may be known about the grade of ore and the reserve tonnage. The purpose of this report is twofold. First, to derive a method of determining purchase price, rate of production and return on investment which is valid under varying conditions of ore grade and tonnage reserve; and, second, to apply this method to the Margay deposit in an attempt to evaluate it as a business enterprise. This is an actual economic analysis of an existing nickel-copper deposit fictitiously named the Margay. It was carried out for a mining corporation and proved to be the determining factor in the subsequent purchase and development of the property. All data referring to costs, quality and quantity of ore, etc., are accurate and truly represented. Prices used are obsolete but the method is not dependent on those variables. Basic assumptions for the analysis are given in Table I, page 71.

Jan 11, 1966

By E. Teghtsoonian, E. M. Schulson

The tensile behavior of bcc ordered P' AuZn single crystals (CsCl structure) has been investigated under varying conditions of temperature, composition, and orientation. Between -0.2 and 0.4 T, multi-stage hardening occurs fm stoichiometric and nonstoichio-metric crystals oriented near the middle of the primary stereographic triangle. At higher and lower temperatures, parabolic type hardening occurs, followed by work - softening at the higher temperatwes. Deviations from stoichiometry give rise to increased flow stresses. Multi-stage hardening was observed for most orientations, except along the [loll-[lll] boundary and near the [001] corner of the stereo -graphic triangle, where parabolic type hardening occurs. Along two slip systems, (hk0)[001] and (, operate simultaneously while in the [001] comer, slip occurs mainly on the system. Electron microscopy of deformed crystals revealed bundles of edge dislocations forming walls approximately Perpendicular to the glide plane. In general the plasticity of 4' AuZn closely resembles the plasticity of bcc crystals. In recent years, considerable interest has arisen concerning the mechanical properties of the CsCl type intermetallic compounds Ag Mg,'- Fe co,' and Ni Al.'-' The compound P'AuZn is structurally similar. It has a low and congruent melting point of 725"~,'" remains ordered up to the melting point,16 and pos-esses a range of solid solubility from 47.5 to 52.0 at. pct Au at room temperature.15 The present paper reports the results of an investigation on the general tensile behavior of material in single crystal form. Some dislocation configurations characteristic of the deformed state are also reported. The results of a detailed study of the slip geometry in AuZn are presented in a separate paper.17 PROCEDURE Alloy preparation, crystal growing techniques, and the procedure followed in selecting specimens of minimum composition variation are reported elsewhere.17 Dumb-bell shaped tensile specimens were prepared by carefully machining single crystals in a jewellers' lathe to a gage length of 0.80 in. and diam of 0.090 in. Back-reflection Laue X-ray patterns and room temperature tensile tests revealed that machining damage could be eliminated by electrochemically polishing 0.005 in. from the machined surface followed by annealing at 300°C for 1 hr. Specimens were polished in fresh 5 pct KCN solution (40°C, 12 v). Experiments were performed by gripping specimens in a self-aligning pin-chuck and threaded collet system, then straining in a floor model Instron tensile machine. All tests were performed in duplicate. Experimental variables included temperature, composition, and orientation. Unless otherwise stated the strain rate was 2.5 x 10"3 per sec. Liquid testing environments included nitrogen (WOK), nitrogen cooled petroleum ether (133" to 293"K), and silicone oil (293" to 488°K). Resolved shear stress-shear strain curves were electronically computed from autographically recorded load-elongation curves. Stress and strain were resolved on the macroscopic noncrystallographic (hkO) [001] system operative under the specific test conditions of temperature, strain rate, and orientation reported earlier.17 RESULTS The temperature dependence of the work-hardening curves is shown in Fig. 1 for gold-rich crystals of 51.0 at. pct Au oriented near the center of the stereo-graphic triangle. Over the range of intermediate temperatures from -200" to 400°K, they are very similar to those classically observed for fcc metals (reviewed by Nabarro et al.).'' The beginning of deformation is characterized by a region of decreasing hardening rate, stage 0, which is followed by a region of low linear hardening, stage I, and then a region of higher linear hardening, stage 11. At the higher temperatures, stage 111 is observed, a region of decreasing hardening rate. Over the intermediate temperature range, the extent of stage 0 and of the slow transition between stages I and I1 decreases with increasing temperature. Total ductility is large, often greater than 300 pct shear. As the temperature is either increased or decreased, the extent of stage I is decreased, giving rise to parabolic type flow and reduced ductility. Similar temperature effects have been reported for bcc ~r~stals.~~-~~ Below -14O°K, hardening is terminated in brittle fracture while above -400°K. initial hardening is followed first by work-softening and then by chisel-edge type ductile fracture. Stoichiometric (50.0 at. pct Au) and Zn-rich (51.0 at. pct Zn) crystals were also tested from 77" to -500°K. The effect of composition on the flow behavior is illus-

Jan 1, 1970

By William P. Kimball, Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expressioll for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: , = Zlxl{xl - P) + ZsXsiP - xs) [I] Zl(xl -P)+ Zs{P - xs) where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, xl and xs are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The d equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid-to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling. the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By T. E. Watkins, M. D. Nelson

INTRODUCTION Deeper drilling for oil is becoming more and more the rule rather than the exception. With deeper drilling come additional problems, perhaps the greatest being those brought on by the higher temperatures encountered down the hole. particularly in the Gulf Coast region of Texas and Louisiana. Temperature gradients of the order of 1.8° to 2.0°F/100 ft are not unusual, and a gradient of 2.3"F.'100 ft is found in some areas of Texas. With a mean surface temperature of 74oF, the following temperatures could be expected for a geothermal gradient of 2.0°F; 100 ft: at 10,000 it. 271°F. 12,000 ft, 314°F: 14,000 ft, 354,oF; and 16.000 ft. 394°F. Severe gelation of lime-base drilling fluid in wells that have high bottom hole temperatures has become perhaps the most serious difficulty enconntered in drilling under such conditions. Lime-base drilling fluids have been very succesefully and widely used in the drilling of wells in the Gulf Coast region because of their inherent stability toward contaminants. their ability to suppress the swelling dispersion of bentonitic shales, and their ease of maintainance. The gradual recognition: during the past few years, that these muds were. in themselve. the cause of many difficulties experienced in drilling has led to wide-pread efforts by the drilling industry. to determine the reasons for the failure of these mud systems and to develop mud systems capable of performing satisfactorily under high-temperature conditios. MANIFESTATIONS OF HIGH-TEMPERATURE GELATION it is generally possible to recognize the symptons of high-temperature gelation early enough that advance predictions can be made of serious difficulties. in mud control, and the useful life of the drilling fluids can be extended by proper treatment. Following i.; a list of the manifestations of high-temperature gelation: (1) The drill string 'takes weight' while going in the hole after a trip. In early stages of high-temperature gelation it is possible to notice a slight reduction in drill string weight as the drill pipe is lowred near the bottom of the hole. (2) Excessive pump pressure is required to .tart the circulation of drilling fluid at or near the bottom of the hole when going hack to bottom after a trip. As the severity of the gelation increases it may be necessary to break circulation a number of times when going in the hole. (3) The drilling fluid from the bottom of the hole is thick and often granular or lumpy when pumped up after making a round trip. In a severely gelled drilling fluid system such a condition may be irreversible; that is, it cannot be stirred or chemically treated to produce a satisfactory drilling fluid. (4) Completion tool.. such as logging tools or perforating guns will not sink to the bottom of the hole. On some occasions completion tools will become stuck and require a fishing job to retrieve them if the wire line attached to them is broken. It is often difficult to determine whether the condition of the drilling fluid is responsible for sticking the tool or whether the wire line becomes key seated in a crooked hole and causes the allow difficulty. When there are 110 other symptoms of high-temperature gelation. then the difficulty may usually be attributed to the latter cause. (5) In extreme cases of high-temperature gelation it is necessary to "wash" and "ream" when going back to bottom after coming out of the hole. (6) In many -instance. it has been found to be extremely difficult and expensive to 1111 production packers 2nd tubing in moderately deep oil wells which had been drilled with a lime-base drilling fluid. In such instances-the original mud had apparently "set" to a consistency approaching that of a weak cement. CAUSES OF HIGH-TEMPERATURE GELATION Extensive test; have indicated that a lime-base mud does not develop a highly gelled condition at temperatures below 250°F. whereas above that temperature such condition often develops rapidly. (Fig. 1) concurrently. the following changes are evident ill the mud: (1) The alkalinity of the mud decreases to a very low value. with both caustic soda and lime being consumed. (2) The quartz content of the mud decreases sharply. (3) The bentonitic content of the mud decreases or di-appears, with concurrent decrease or loss of base exchange capacity of mud solids. (4) New compounds formed in the mud have been found to be cal-cium silicate, calcium aluminum silicate, and calcium sodium aluminum silicate. (5) The mud loses the ability to form a filter cake of low permeability. The above characteristics have been discussed, in part. by other authors

Jan 1, 1953

By W. D. Bennett

AN interesting effect has been observed in the vacuum etching of titanium in the high temperature ß phase. Using a high vacuum annealing furnace, operating at less than 2x10-6 mm with a tubular titanium liner, it has been found possible to etch polished metallographic specimens at different temperatures between room temperature and 1000°C without contamination or increase in hardness.' Heat etching of titanium has been reported by other workers,' but the following example is of interest as an experiment under high vacuum in the absence of any contamination. Two polished specimens of iodide-processed titanium are placed at different positions along the axis of the furnace corresponding to temperatures of 900" and 800°C above and below the a-ß transus. The specimens are then raised to these temperatures and annealed simultaneously for 3 hr under the same high vacuum conditions. After cooling and withdrawing the specimens, their surfaces are photographed without further treatment. Figs. 1 and 2 show the results for the 800" and 900°C specimens, respectively. Fig. 1, corresponding to a vacuum etch in the a region, shows a typical equiaxed structure with what appears to be a slight shift of grain boundaries. Fig. 2, corresponding to a vacuum etch in the ß region, shows an equiaxed type of structure with the growth of striations in certain grains. The striations are only superficial, as a light polish and chemical etch restores the clean equiaxed structure. The vacuum etch, occurring as it does above the a-ß transus, records the state of the metal in the ß phase by means of the surface relief produced by the selective evaporation of metal from different grains; the metal itself reverts to the equiaxed a on cooling. The nature of the ß etch" (Fig. 2) suggests that, in transforming from the close-packed-hexagonal a to the body-centered-cubic ß lenticular-shaped laminae are formed parallel to common planes of the two structures. This would explain why some grains appear to be unaffected by the etch. The technique has interesting possibilities in the investigation of the mechanics of high temperature transformation. Acknowledgment This note is published by permission of the Deputy Minister, Dept. of Mines and Technical Surveys, Ottawa, Ont., Canada.

Jan 1, 1956

By Charles Catlett

Some years ago the writer was struck by what might be called the remarkable vitality of the Virginia furnaces during the panic of 1893; and attention was called to the fact in the American Manufacturer of February 8,1895. From the second half of 1892, which was a period of maximum output, to the second half of 1893, when the full effects of the depression had been reached, the output of pig-iron had fallen off in Illinois 85; in New York, 66; in Ohio, 51; in Tennessee, 44; in Pennsylvania, 28; and in Virginia only 15 per cent. It seemed a reasonable inference that the State which had thus shown its marked ability to meet hard times could make and market its product with a larger margin of profit than any of the other States. This was true at that time, and to a certain extent the reasoning still holds good; but my mistake was in not fully realizing the marked effect of the Mesabi development, combined with reduced economies in transportation, and the consequent advantage to those furnaces which were so situated as to utilize these new commercial factors. The effect of these factors is seen in comparing the second half of 1894 with the second half of 1892. New York had dropped off 44, Alabama 23, Tennessee 21, Illinois 19, and Virginia 16 per cent., while Pennsylvania had increased 5 and Ohio 10 per cent. While there is no question of the great economy which has been made possible for certain interests which are peculiarly situated with reference to the ores of the Northwest, it is yet too early to say what furnaces not so fortunate will have to pay for their raw material. Already an increase of twenty cents per ton of ore has been announced, based upon increased cost of production.

Jan 1, 1900

By Boyd Dudley, R. H. Richards

In nearly all ore-dressing operations it is a common practice to discharge mixtures of fine ore and water through spigots; for example, from classifier pockets, from jig hutches, from settling tanks, etc. As a general rule it is desirable to regulate the composition, i.e., the ratio of water to sand, of such discharged products; and this can usually be done by varying the size of the orifice or spigot through which the material is discharged. Thus it is that problems similar to the following are frequently encountered: With a given quantity of solids per unit time, of a given specific gravity, to be discharged with water under a given head, and with a given ratio of water to solid, what must be the size of the spigot opening? If the spigot is to be open continuously, there are, aside from its form, but three factors governing the rate at which it will discharge a mixture of sand and water, namely: the head of water above the spigot; the area of the spigot opening; and the viscosity of the material to be discharged. The term viscosity, as used here, means the ratio of the volume of pure water that will flow through a given orifice under a given head in a given time to the volume of the material under consideration that will flow through the same orifice in the same time under the same conditions. While the actual viscosity of water containing sand in suspension is not increased by the presence of the sand, nevertheless the volume-rate at which such a mixture will flow through an orifice is less than that at which pure water will flow, by reason of the friction of the particles of sand against each other and against the sides of the orifice. In other words, the flow is retarded as it would be by increased viscosity; and therefore, for the purpose in view, we may speak of the viscosity of a mixture of ore grains and water as defined above. The head of water above the spigot is generally fixed by the form and design of the classifier or tank to which the spigot is attached. So, with the head known, in order to determine the size of the spigot required it is necessary to know the viscosity of the desired mixture, and the coefficient of discharge of

Jan 1, 1915

HenRy Clay FRick, a pioneer in modern coke and steel industry and, in more recent years, one of the outstanding financiers of America, died on Dec. 2, 1919, at his home on Fifth Avenue, New York. Although he had been ill since election day, when he had an attack of indigestion which developed into ptomaine poisoning, his death was a surprise to all. He is survived by his widow, Adelaide Howard Childs Frick; a son, Childs Frick, one unmarried daughter, Helen C. Frick, and four grandchildren. A quiet funeral service was conducted at the Frick home on Wednesday afternoon by the Rev. Dr. Leighton Parks, pastor of St. Bartholomew's Episcopal Church. This was attended by members and very intimate friends of the family, Trustees of the Metropolitan Museum of Art, Officers of the Links Club, and Directors of the United States Steel Corpn. Henry Clay Frick was born Dec. 19, 1849, in West Overland, Westmoreland Co., Pa. His father, John W. Frick, was a farmer of Swiss ancestG, and his mother, Elizabeth Overholt Frick, a member of an old Mennonite family. Until he was sixteen, he spent his time at school, on his father's farm, and in his grandfather's distillery, where he kept books. He attended Otterbein University, in Ohio, for a year. Frick, learning that coke was an essential of the already rapidly developing steel business, early invested every cent he could get in coking-coal lands. With the help of an associate of his grandfather, he formed the corporation of Frick & Co., coke dealers, and acquired fifty-one ovens in the Connellsville region and 300 acres of soft-coal lands. During the panic of '73, with the help of Judge Thomas Mellon, a Pittsburgh 'banker, he bought out his partners and while coke was selling at 90 cents a ton enlarged his purchases of suitable lands. Later, the price of coke increased until it was selling at $5 a ton. Before he was 30 years old, Frick was rated a millionaire. Association with CaRnegie In 1878, he sold an interest in the business Do E. M. Ferguson of New York, and later a share to Mr. Ferguson's brother. Four years later the business was reorganized into the H. C. Frick Coke Co. with vast coal lands, great banks of ovens, and a capitalization of $2,000,000. Then began his association with Andrew Carnegie. He exchanged a part of his coke interest for shares in Carnegie Brothers of Pittsburgh,

Jan 1, 1920

By Benj. Lazer

Multiple seam mining has been studied and writ- ten about extensively in the past and in the latest review of the subject in 1956 David Stemple covered it exhaustively. The present discussion has to do with only one phase of the problem-"The effects on upper seams when the lower seams have been mined first." The study presented here is based on observations made in mining operations in southern West Virginia and adjoining areas of Virginia and Kentucky during the past 43 years. These observations are largely confined to the Pocahontas coalfields of southern West Virginia which have, since 1883, produced well over one billion tons of coal from an area of about 300 sq miles and where multiple seam mining has been active, or is now active, at more than 40 operations. The observations and conclusions as to the effects on upper seams when lower seams have previously been mined are therefore related only to the local coalfields in the area of the three states named but I believe that they can be applied generally to other coalfields.

Jan 9, 1965

Christopher R. Corning was one of the ablest mining engineers and geologists in America and one whose name was well known also in Mexico, Cuba, South America and many European countries. He was educated at Zurich, Switzerland, and at the Bergakademie, Freiberg, where he was graduated in 1883 with the degrees of Markscheider and Bergingenieur. He continued his studies at Heidelberg until 1886, chiefly in chemistry, under Bunsen, and mineralogy and petrography under Rosenbusch. Although he received a Ph.D. in chemistry, he never used the title. During holidays of 1883-86, he traveled, seeing mines and studying geology in Spain, France, England, Italy, Germany, and Austria. In 1886, he returned to America and in 1887 he was in the Lake Superior iron ore country on the staff of John F. Stevens, then building the Duluth South Shore and Atlantic Railway. In 1889, Mr. Corning was at the Bunker Hill & Sullivan mines at Wardner, Idaho, with John Hays Hammond, and there met E. E. Olcott. Although Mr. Corning was not long connected with the Bunker Hill & Sullivan mines, he left the imprint of his ability and splendid personality upon the men and the property. That his friendship was cherished was manifested by the cordiality, hospitality and frequency of letters of good counsel and cheer. In 1897, Mr. Corning, with E. E. Olcott and Prof. Robert Peele of Columbia University, formed the firm of Olcott, Corning & Peele, consulting mining engineers. Pressure of university duties compelled Professor Peele to withdraw in 1904, and later Mr. Olcott was forced to retire by reason of other important business interests, but the friendship and high mutual regard of the three men continued undiminished. About 1902, Mr. Corning and Professor Peele translated into English Riemer's book on "Shaft Sinking under Difficult Conditions." Mr. Corning's knowledge of structural geology, mineralogy and ore deposits was extensive and accurate. He was a close and intelligent observer. When he became interested in a problem, no amount of trouble was too great in endeavoring to reach a satisfactory solution. He had professional experience in the West, notably in the Coeur d'Alenes, Mexico and South America, and several times was called on to attempt to straighten up mismanaged properties. In 1912, at the request of a large number of members, Mr. Corning headed the "Committee of FiveJ' that investigated the affairs of the American Institute of Mining Engineers and brought about beneficial changes in the organization and its policies. He was one of the organizers

Jan 1, 1924

By B. H. Caudle, R. E. Watson, I. H. Silberberg

The production history of an inverted nine-spot injection pattern was studied with a porous plate model similar to Habermann's. Colored fluids were used so the boundary movements could be photographed. By varying the production rates of the side and corner producing wells, the optimum pattern sweep efficiency can be obtained. Results of the laboratory tests indicate that interpolation of the pattern sweep and conductivity ratio data will permit application of the data to predicting fluid injection operations with mobility ratios between 0.1 and 10 and production rate ratios between I and the optimum values. INTRODUCTION The inverted nine-spot injection pattern in Fig. 1 has some unique advantages over other regular injection patterns (five spot, line drive, etc.) used in secondary recovery operations. It has three producing wells for each injection well, while the five-spot and line-drive patterns require an equal number of injectors and producers. Futher-more, of the eight producing wells surrounding each injection well, four are of the "side well" type which lie nearer the injection well than the remaining four "corner wells". This allows the production rates of these two types of wells to be adjusted independently of each other to obtain better pattern sweep efficiency. This latter advantage may well be the reason why the nine-spot patterns have not been studied as extensively as the patterns containing only one type of injection or producing well. The pattern sweep efficiency of the inverted nine spot is affected almost as much by operating with different producing rates of the comer and side wells as by differing mobility ratios. Possibly because of this added operating parameter, published studies of nine-spot systems have been limited in their coverage of the pertinent variables.'-' The model studies reported here covered the mobility-ratio range normally found in waterflood operations, as well as the variation in well production rates necessary to achieve optimum pattern sweep efficiency. Conductivity ratios — a measure of the change in total flow at constant pressure difference — were obtained during each model run. A porous-plate model with miscible fluids representing the in-place and injected fluids was used in this study. This model technique is the same as that used in both X-ray shadowgraph" and visual techniques4 described in the literature. Using miscible fluids eliminates residual oil in the model, and the permeability to the injected fluid is the same as to the in-place fluid. Thus the mobility ratio in the model is given by the ratio of the viscosity of the displaced fluid to the viscosity of the injected fluid. Because of the non-linear nature of the viscosity vs composition curve for two miscible liquids, the mobility change across the boundary between the two fluids is reasonably sharp. This technique thus represents the displacement of a region of one fluid mobility by a region of possibly different mobility in an isotropic system under steady-state flow conditions. Table 1 shows the dimensionless similarity groups used to scale the model conditions and results to

Jan 1, 1965