Search Documents

By Cleland N. Conwell

Reclaiming mined land in northern regions is less difficult than reclaiming semiarid lands. In 1972, the Usibelli coal mine near Healy, Alaska, initiated experimental plots to determine the proper grasses and amounts of fertilizer. The following spring, approximately 1600 acres of land disturbed by mining were seeded by low-flying aircraft. The reclamation project was evaluated by the State of Alaska and has been adjudged successful. The information gained is being used in reviewing prospecting permits and granting coal leases on state lands.

Jan 1, 1977

By A. E. Jenkins, L. A. Baker, N. A. Warner

Rates oj decarburization of levilated Fe-C droplets conlaining 5.5 to 0 pct C have been measured at 1660°C. Gas mixtures of 1, 10, and 100 pct 0, with helium diluenl were used at velocities of 12.5 and 62.5 cm per sec. Rates were independent of carbon concentration in the mell and in good agreement with the calculated rule of oxygen diffusion through the gas boundary layer. The effects of flow rale and total pressure are as predicled and the rates are approxitnalely 2.5 times those with CO2 as oxidant. The mass-transfer correlation used incorporaled the efject of natural convection as well as forced conrection. Graphile spheres are shown to oxidize at the same rate as Fe-C droplets under the same experimental codlions. It is concluded that, for high carbon concentrations in the melt, the rate of- decarburizalion is controlled wholly by the rate of gaseous diffusion. Rate measurements with pure CO, are reported for low carbon concentrations where CO bubbles nucleate within the droplet. Under these circumstances the decarburi-zation decreased with carbon concentration and it is proposed that carbon diffusion is significant in conlrolling the decnvburization rate. In an earlier paper1 decarburization rate measurements were reported for levitated Fe-C alloys at 1660°C but with CO2 as the oxidant. The decarburization rate was found to be independent of carbon concentration in the melt but slightly affected by total pressure. The authors were unable to explain the slight pressure effect but in all other respects the results were consistent with control by diffusion in the gas boundary layer. Subsequent work has been directed at finding the reason for the slight pressure effect and whether the kinetics with oxygen as oxidant parallel those with CO2. Recently Ito and Sano2 have shown that with water vapor-argon atmospheres the decarburization rate is gaseous diffusion controlled until an oxide film appears on the surface. In this work the melts were contained in crucibles. MASS TRANSFER IN THE GAS PHASE In the earlier analysis1 only forced-convection mass transfer was considered. Subsequent recognition of the existence of some free-convection mass transfer explained the observed small effect of total pressure on the decarburization rate. Steinberger and Treybal3 and Kinard, Manning, and Manning4 have developed correlations involving the linear addition of the contribution of radial diffusion, free and forced convection. Steinberger and Treybal&apos;s correlation was chosen as the most applicable to the present work since it correlated most of the data available in the literature and handled the low Reynolds number region exceptionally well. The correlation for (Gr&apos;Sc) < 108 is where Nu&apos; is the Nusselt number for mass transfer based upon the total surface of a sphere in an infinite medium, G&apos; is the mean Grashof number for mass transfer defined by Eq. [2], Sc is the Schmidt number (µ/pDAB)f, Re is the sphere Reynolds number (dpu,pf/µf), p is the viscosity of the gas (poise), p is the density of the gas (g cm-3), Dab is the binary diffusivity for the system A-B (sq cm sec-&apos;), dp is the sphere diameter (cm), u is the approach velocity of the gas (cm sec-I), and subscript f denotes the property value is computed at the film temperature Tf defined by Tf = +1/2(To + Tr) where To is the specimen temperature and T, is the approach gas temperature (oK). Natural convection occurs when inhomogeneities exist in gas density. These may be caused by concentration gradients, temperature gradients, or both. In the present work the temperature gradient between the sphere and the bulk gas was very large and in some cases, for example the runs with pure oxygen, the concentration gradient was also appreciable. The Grashof number defined by Mathers, Madden, and piret5 was used since it took account of both temperature and concentration gradients: where Gr&apos; is the Grashof number for mass transfer (p2fgd3|-yA-yA|/µ2f), Gr is the Grashof number for heat transfer (p2f gd3p|To - T,]/µ2fTf), Pr is the Prandtl number (cpµ/k)f, g is the acceleration due to gravity (cm sec-&apos;f, a is the concentration densification coefficient (1/p)(ap/ayA)T, yA is the mole fraction of component A at the gas-metal interface, yA is the mole fraction of component A in the bulk gas stream, cp is the heat capacity of the gas per unit mass at constant pressure (cal g-I OK-&apos;), and k is the thermal conductivity of the gas (cal cm-&apos; sec-1 OK-1). Mathers et al. tested this combined Grashof number

Jan 1, 1968

By L. R. Flint, W. L. Freyberger, W. J. Howarth

W. L. Freyberger (Director, Institute of Mineral Research, Michigan Technological University, Houghton, Mich.)-The authors are to be complimented on their theoretical analysis of a column flotation process, and the comment I wish to make is not related to that analysis, but to the use of the word "countercurrent" to describe that process. Strictly speaking, the process the authors have described is countercurrent only in the sense of particle-bubble contact. That is, as solid particles and air bubbles pass through the column, the leanest flotation feed (the tailing) comes in contact with the greatest concentration of mineral-free bubbles. However, air bubbles alone do not comprise the complete extracting phase in a flotation system. A second component of this extracting phase is the collector, which is really the extractant inducing transfer of mat-

Jan 1, 1972

By Wolfram Ruff, H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ‡ There is, however, a distinct metallographic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others 1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1935

By T. A. Rickard

A knowledge of the principles of punctuation is essential to effective and intelligible writing, for the ease and pleasure of the reader, and even his understanding, may depend upon the choice and the placing of punctuation marks. To &apos;punctuate&apos; is to mark with stops or points; the word comes from the medieval Latin punctuare (punctuatus), which in turn is derived from the Latin punctum, a point. The purpose of punctuation is to show the manner in which the writing is to be understood; to indicate the relations between parts of a sentence and between successive sentences. To some extent "it does for the eye what vocal stress does for the ear", but especially it marks logical relations. Some punctuation marks, such as those indicating admiration, exclamation, and interrogation, are rhetorical as well as grammatical, but most of the common ones are logical, or grammatical. My discussion will be confined to grammatical punctuation in ordinary writing. .&apos;The problem of punctuation in text matter", as George Summey * says, "is to employ words, points, and paragraph breaks in such a way as to achieve at the same time clearness; proper distribution of emphasis, and the desired kind of movement." The criticism of the punctuation of a sentence or of a group of sentences is not final until the context, within the paragraph, is read. A paragraph is a sentence or a group of sentences forming an independent unit of the composition; it represents a unit of thought. A multiplicity of paragraphs produces a choppy effect; &apos;on the other hand, paragraphs of. excessive length are tiresome, because the belaboring of one unit of thought wearies the reader. The aim should be to

Jan 1, 1931

By William Glenn

Almost beyond doubt, the most important contribution to the assaying of copper yet made, is that of Mr. Eustis (Bans., xi., 120) on the " Comparison of Various Methods of Copper Analysis," which indicates in a manner for which the assayer cannot but feel grateful, how a copper sample ought to be treated from the moment it enters the laboratory until the copper is finally weighed. Admitting, as the present writer is inclined to do, that this paper establishes, as the official standard, the method of electrolysis, we may note as one of the few details which it does not finally fix, the kind of battery most desirable for precipitating the copper upon platinum. In this respect each assayer appears to be a law unto himself, while all feel more or less " shaky " as to the results. Classsen seems to suggest a remedy when he directs the measuring of the -gases liberated by the battery employed. But, in fact, that measure is not a constant in the Bunsen elements which he prescribes for copper determination. Furthermore, measuring gases necessitates more machinery and labor than the average assayer has a stomach for. It is, however, but just to Classen, to whom we owe so much, to reeall that he wrote more especially for students in the schools.

Jan 1, 1889

By Warren B. Weeks

Continued development in the deeper fields discovered during 1937 and 1938 was largely responsible for the 16 per cent (2,913,400-bbl.) increase in production, bringing the 1939 output to 21,376,230 bbl., the largest for South Arkansas since 1929. The older settled fields continued to decline and Rodessa was added to this classification. Magnolia field accounted for much of the increase, with Schuler field showing only a slight increase. There were 248 wells drilled during 1939, five more than during the previous year. Of 198 wells drilled in proven fields, 21 were dry; 46 of the 50 wildcats drilled were dry. The old depth record of 8332 ft. was increased to the present record of 9028. Trend of Prospecting Production from the porous " Reynolds " oolite zone of the Smackover limestone continued to be the objective of prospecting. During the year 20 seismograph, 3 gravity meter, 1 magnetometer, 1 soil analysis and 1 electromagnetic crews were reported in the state. The geophysical work was largely concentrated in three southern counties: Columbia, Lafayette and Union. As indicated in Table 2, the same three counties received most of the important drilling tests. At the end of the year only three seismograph crews remained in the areas. The area for prospecting Smackover limestone was greatly narrowed during the year by the failure of two "fault zone" wells to find satisfactory permeability in the oolite zone, and by the relatively thin sections of porosity found in wells drilled in townships 18 and 19 South. Geology Most of the wells listed in Table 2 afforded additional control on structure of the lower beds, but gave little new information on stratigraphy. Of the 248 wells drilled, 3 ended in Tertiary, 34 in Gulf, 1 in Paluxy, 29 in Glen Rose, 15 in Travis Peak, 15 in Cotton Valley, 139 in Smackover, 2 in Eagle Mills and 10 in Carboniferous. The age of the beds between the Travis Peak formation and Carboniferous is still questionable. Most

Jan 1, 1940

By Warren B. Weeks

Continued development in the deeper fields discovered during 1937 and 1938 was largely responsible for the 16 per cent (2,913,400-bbl.) increase in production, bringing the 1939 output to 21,376,230 bbl., the largest for South Arkansas since 1929. The older settled fields continued to decline and Rodessa was added to this classification. Magnolia field accounted for much of the increase, with Schuler field showing only a slight increase. There were 248 wells drilled during 1939, five more than during the previous year. Of 198 wells drilled in proven fields, 21 were dry; 46 of the 50 wildcats drilled were dry. The old depth record of 8332 ft. was increased to the present record of 9028. Trend of Prospecting Production from the porous " Reynolds " oolite zone of the Smackover limestone continued to be the objective of prospecting. During the year 20 seismograph, 3 gravity meter, 1 magnetometer, 1 soil analysis and 1 electromagnetic crews were reported in the state. The geophysical work was largely concentrated in three southern counties: Columbia, Lafayette and Union. As indicated in Table 2, the same three counties received most of the important drilling tests. At the end of the year only three seismograph crews remained in the areas. The area for prospecting Smackover limestone was greatly narrowed during the year by the failure of two "fault zone" wells to find satisfactory permeability in the oolite zone, and by the relatively thin sections of porosity found in wells drilled in townships 18 and 19 South. Geology Most of the wells listed in Table 2 afforded additional control on structure of the lower beds, but gave little new information on stratigraphy. Of the 248 wells drilled, 3 ended in Tertiary, 34 in Gulf, 1 in Paluxy, 29 in Glen Rose, 15 in Travis Peak, 15 in Cotton Valley, 139 in Smackover, 2 in Eagle Mills and 10 in Carboniferous. The age of the beds between the Travis Peak formation and Carboniferous is still questionable. Most

Jan 1, 1940

By W. N. Logan

THE petroleum industry of Indiana made somewhat notable progress during the year 1923, considering the number of handicaps it encountered. The price of labor and materials continued to have an upward slant while the price of crude oil took a decidedly downward course. In spite of these adverse conditions, the quantity production will closely approximate that of 1922, when it passed the million-barrel mark. The progress of the industry in Indiana should be considered fairly satisfactory as long as the present production is maintained. In other words, if the loss of production from the waning old wells can be offset by the production from the new for a period of 10 or 15 years longer, the industry may have cause for congratulation. SUB-TRENTON INVESTIGATIONS In recent years a number of tests of strata lying below the Trenton limestone have been made in Indiana. Several of these tests were completed in 1923. Indications of oil were reported by drillers from several horizons below the Trenton. The most satisfactory of these came from the St. Peter sandstone lying immediately below the Trenton limestone, but no production has yet been obtained from any of the Sub-Trenton horizons. Glen Valley Wells.-Two wells in Marion County were drilled into the St. Peter sandstone, 1 mi. north of Glen Valley and 9 mi. south of Indianapolis. About 30 ft. of sand saturated with a dense asphaltic oil was found in the upper part of the St. Peter sandstone in one of the wells, which contained about 10 per cent. of the light oils, or more easily volatile constituents, and about 90 per cent. of a dark, dense, asphaltic residue. The oil resembled the residue of an asphaltic petroleum from which the more volatile oils had disappeared.

Jan 3, 1924

By Charles B. Forgan

THE Stan Trg ore body now being exploited by Trepca Mines, Ltd., originated by the metasomatic replacement of limestone and consists mainly of an intimate mixture of sulfides associated with little admixed gangue. The chief sulfides are galena, marmatite, pyrite, and pyrrhotite. Geological structure, embracing both igneous and sedimentary agencies, exerts important control on ore deposition and presents many features of great interest. Geological Formations and Intrusives Stag Trg Series-The dominant formation is the Stan Trg series, which

Jan 1, 1936

George W. Maynard, New York, N. Y.:—It is well known that there are many magnetite-mines of which the ore is too low-grade for direct use in the blast-furnace. For carrying out the sintering process, the preliminary step, in the case of magnetites, is the separation of the ore from the gangue by magnetic concentration. The resulting fine-grain product is very objectionable in the blast-furnace, and when used must be a very small percentage of the charge. The sintering process has saved the situation by furnishing a product which is absolutely ideal on account of its cellular structure. (In reply to questions by W. J. Tudor, and Joseph W. Richards, the following additional information was given by Dr. Maynard.) The percentage of iron in the product is determined entirely by the degree of concentration of the raw material and is practically not increased by the sintering operation. The magnetic concentrates at Port Henry and at the Benson and one or two other mines contain from 65 to 67 per cent. of metallic iron. The cost of sintering is from 39 to 41 cents per ton of product, including superintendence, depreciation, and repairs. The itemized figures are about as follows : Mixing (including labor), 24; power, 9; ignition, 5; repairs, 3; total, 41 cents. Prof. J. W. Richards, South Bethlehem, Pa.:—From a metallurgical standpoint I question the accuracy of the statement on p. 374: " C.—An increased reducibility of the iron so treated. (This has been conservatively estimated as 5 per cent. better than the best available ore.)" It seems to me that when a material is&apos; sintered in this way, the constituents present, as lime, silica, and alumina, have a chance to form a compound with the iron oxide; that such a compound, if formed before the material goes into the blast-

Jan 1, 1913

By W. T. Isbell, Carleton C. Long

Zinc recovery from lead blast-furnace slags has heretofore been an indirect process, involving, first, the fuming off and collecting of an impure zinc oxide, and second, the reduction of the zinc portion of this oxide to metal either by electrolytic or pyrolytic means. (In a variation of this process, blue powder is the intermediate product rather than zinc oxide fume.) In 1940, W. T. Isbell proposed that molten slag from the lead blast furnace or stock-pile slag melted down in a blast or cupola-type furnace be charged directly into an airtight container (i.e., furnace) provided with means to heat further the slag by passage of electric current and means to introduce the carbon (coke) necessary to reduce the ZnO constituent of the slag to zinc as a zinc vapor and CO. He also proposed that the zinc vapors so obtained be condensed in a Weaton-Najariant internal condenser directly connected to the proposed furnace. It was thought that the Weaton-Najarian condenser could liquefy zinc vapor from lean mixtures of vapor and noncondensable gases. Such condensers have been in commercial use! since 1936 at Josephtown smelter, where the source of zinc vapor is a column of coke and zinc-bearing sinter electrically heated (charge resistor). Condenser output when supplied with vapor-gas mixtures containing approximately 45 per cent zinc and 55 per cent noncondensable gases, varies from 18 to 30 tons of slab zinc per day per condenser, depending upon the heat-transfer area (length) of the condenser and the volume of vapor (furnace size) fed to it. Lead-smelting operations at the St. Joseph Lead Company&apos;s plant at Hercu-laneum, Mo., produce a slag containing 12 to 16 per cent zinc. For several years this slag has been stock-piled with the object of recovering the zinc values if and when a commercial method was invented. Evaluation of the possibilities of the proposed method was made by pilot-plant operation at Josephtown. The first plant, designed in 1940 and operated in early 1941, consisted of a single-phase, two-electrode furnace. The evolved vapors were burned. Electrical characteiistics of the molten slag, power requirements, coke requirements, and extent of zinc elimination indicated the feasibility of the proposed method. In the latter part of 1941 a second pilot furnace was constructed, to which "was attached a small (6 ft. long) Weaton-Najarian condenser in order to develop an over-all picture of zinc-in-slag to zinc-in-slabs. This furnace was operated in the early part of 1942 and yielded such promising results that a decision was made to design- and construct a commercial furnace. Feed for the pilot-plant furnaces was granulated slag. A suitable deduction (300 to 350 kw-hr. per ton slag) was calculated in estimating power require-

Jan 1, 1944

By H. Foster Bain

THE "miracle of production." which was such an essential element in winning the European war, was nowhere more in evidence than in our Western States. In shipbuilding alone the Pacific Coast States -et a mark never before equaled, and in production of war goods of many kinds, both Rocky Mountain and Coast States accomplished more than their proportionate share if measured by population standards. This was only possible because of the building of immense new plants of many types, largely financed with Government money. Their operation has built up payrolls in the West and brought a measure of prosperity which Westerners are naturally anxious to have made permanent. A widespread doubt obtains, however, throughout the nation and even in the Western States themselves, as to whether, and if so to what extent, this may prove possible. The question has been raised as to whether the national treasury has not been raided to stock the Western ranges with a voracious breed of white elephant .

Jan 1, 1945

By S. FROES ABRUE

No new oil fields were discovered in Brazil during 1945. Production for the year reached a total of 79.329 bbl., all coming from the four fields in the Baia basin; the Lobato-Joanes field produced 6728 bbl.; Aratu, 6717 bbl.; Candeias, 36,663 bbl. and Itaparica, 29,211 bbl. The total cumulative production from the Baia basin from 1939 to 1945 inclusive amounts to 210,000 bbl., all of which is utilized locally.

Jan 1, 1946

By R. L. Fullman

IN the investigation of metallurgical transformations and the relationships between microstructure and properties of metals, it frequently is desirable to obtain a measurement of the relative amounts of the various phases present and of the mean size of particles into which each phase is dispersed. The relative amounts of the phases can be measured by the classical methods of area, lineal, and point analysis,1-5 in accordance with the principle that the volume fraction of a phase, the fraction of a polished cross section occupied by the phase, the fraction of a random line occupied by the phase, and the fraction of randomly arrayed points occupied by the phase are all equal. The validity of this relationship depends only on the attainment of a truly random sample of area, length, or points, and not on the size, shape, or distribution of the particles constituting the phase. Smith and Guttman8 have derived a relationship between the interface area per unit volume S, and the measurable quantities L., the interface length per unit area on a cross section, and NL, the number of interfaces per unit length intersected by a random line. Their equation, Sv = — L8 = 2NL is also valid regardless of the distribution of particle sizes and shapes. In contrast to the situation concerning measurement of relative fractions of phases and of interface area, the measurement of particle sizes in opaque samples has not been subjected to a complete analysis. It has been common to measure some lineal or area dimension of particles on a polished cross section and to use the mean value as a qualitative measure of particle size. In the present paper, quantitative relationships are established among the various mean dimensions on a polished cross section and the actual dimensions of the particles present. Particles of Uniform Size Spheres: If a metal sample contains particles of a phase a dispersed in the form of spheres of uniform size, a polished cross section through the sample will reveal circular areas of phase a with radii from 0 to ?, the radius of the spheres. Consider a cube of unit dimensions to be cut from the sample. If a cross section parallel to one of the cube faces is examined, the average number of particles per unit area (N,) equals the number of particles per unit volume (Nv) times the probability p1 that the plane would intersect a single sphere positioned at random within the unit cube. Since, of the various possible positions for the cross-sectional plane over the unit length from top to bottom of the cube, only those positions existing over the length 2r would lead to the plane intersecting the sphere, the probability of intersecting a single sphere is just 2r. N8= Nvp1 = Nd-2r [1] Applying the equality of area and volume fractions, the relationship is found between sphere size and average area s of uniform spheres intersected by a random cross section, 4 - f = NV V = Nr . — pra = N s = Nd . 2rs S = —pr2 [2] A similar analysis reveals the average traverse length across spheres of uniform size when random lines are passed through the sample. If a randomly oriented unit cube is cut from the sample and a randomly positioned line is passed through the cube parallel to a cube edge, the number of spheres intersected by the line (Nl) equals the number of spheres per unit volume times the probability p1 of the line hitting a single randomly placed sphere in the cube. Since possible positions of the line occupy unit area, and possible positions for which it will pass through the sphere occupy an area of pr2, the probability of the line hitting a randomly placed single sphere is pr2. NL = Nv p1 = Nvpr2 [3] Combining this relationship with the equality of volume and lineal fraction, the desired relationship is obtained between radius and mean lineal traverse length -i, for spheres of uniform size. 4 - - 3 l=4/3r [4] Circular Plates: Consider a sample containing particles of a phase a in the form of circular plates of uniform radius r and thickness t, where r >> t. If the plates are randomly oriented, as in a sufficiently large sample of a fine grained polycrystalline material, area and lineal analysis may be carried out with parallel cross-sectional planes and lineal traverses. If the plates are not randomly oriented, it is necessary to randomize the orientation of the cross-sectional planes and traverse directions. Let a unit cube be cut from the sample, and a cross-section plane be passed through the cube parallel to one of the cube faces. The number of plates cut by the cross-sectional plane per unit area is equal to the number of plates per unit volume times the probability of a plate intersecting a single randomly positioned and randomly oriented plate in the cube. If J is the component of the plate diameter in the direction normal to the cross-sectional planes, the probability of a plane cutting a single randomly oriented plate is equal to J, the mean value of J for all possible orientations of the plate. Let 4 be the dihedral angle between a plate and the cross-sectional plane, and let p?, d? be the probability that a plate makes an angle between 4 and ? + d? with the cross-sectional plane. Then for ran-

Jan 1, 1954

By T. A. Rickard

INTRODUCTORY. THE presentation to the Institute, eight years ago, of the paper of Pošepny on " The Genesis of Ore-Deposits " has borne fruit in much fresh: investigation, as is evidenced, for example, by the group of very valuable papers, by distinguished members" of the United States Geological Survey, read at the Washington meeting-discussions of general principles particularly suggestive to those who are engaged in mining. Pošepny, in the discussion of his famous treatise, said that the present writer seemed to look at every new conception in ore-deposition" from the sole standpoint of its immediate usefulness in mining."* Protesting mildly against " sole " and "immediate," I accept the impeachment. It calls for no defence. THE DEVELOPMENT OF RECENT THEORIES. Given the idea of an underground water-circulation as the chief factor in the deposition of ore, the next step in the inquiry as to the genesis of such deposits is, the endeavor to determine which particular part of the general water-circulation is responsible for the results. Around this question have centered the controversies of a generation, and to these controversies we owe the gradual clarification of our ideas upon the processes of ore-formation. It is unnecessary to sketch here their progress from Werner to Le Conte, who combated in 1883 the extreme views of the lateral-seeretionists, and in 1893 opposed the narrow interpretation of the ascensionist-theory. The generally accepted opinions of to-day are a well-deserved tribute to his philosophic discrimination. Thanks to Prof. Van Hise and Mr. Slichter, whose work he utilizes, we have now arrived at a comprehensive conception

Jan 1, 1902

By A. W. Edelen, H. V. Lee

THE Teziutlan copper-zinc deposit is supposed to be of late Cambrian or early Paleozoic age. The country rocks are a series of schists or phyllites, flat lying and in the form of a plunging anticline. The ore deposit occupies a single horizon in the schist for a known horizontal extent of 1200 meters. Along its strike occur four large lenses or ore bodies. These ore bodies occupy positions along the flank and extend to the crest of the anticline. The primary mineralization is in the form of quartz, pyrite, sphalerite, chalcopyrite and galena, with a few scattered silver anti-monides. Quartz and pyrite form the mineralization between the ore lenses. In the ore lenses the sulphides appear as a massive, very he-grained intergrowth of minerals. The intergrowth suggests a contemporaneous deposition of the heavy sulphides. The grain size, usually under 0.09 mm., makes the separation difficult and fine grinding important. The ore bodies were formed at great depth by solutions probably originating in the same basic magma that gave rise to the dolerite sills that are so common in their vicinity. INTRODUCTION The Teziutlan copper-zinc deposit is distinctly different from other ore deposits of Mexico in age and type. Previously stated to be pre- Cambrian in age, it is now quite generally supposed to belong to the late Cambrian or to the early Paleozoic period. Also, in contrast to the usual shallow-vein zone type of mineralization in Mexico, there is here exemplified an intermediate vein zone deposit of copper and zinc. So far as is known, the Teziutlan vein is unique in the history of Mexican geology and in a class by itself, its closest counterpart probably being the copper veins of the pre-Cambrian of Canada. The Teziutlan district is in the extreme northwestern corner of the State of Puebla, Mexico. Teziutlan, the terminus of a branch line of the National Railways from Mexico City, is connected to the mine at Aire Libre by a 17-km. narrow-gauge railroad owned and operated by the Teziutlan Copper Co. Owing to excessive grades on this short line, Shay-geared locomotives are used for the transportation of concentrates and supplies.

Jan 1, 1937

By P. Niessen, S. J. Bercovici

RECENTLY Aust et al.&apos; proposed a model of non-equilibrium grain boundary segregation based on a vacancy gradient induced uphill diffusion process of solute to grain boundaries. According to their proposal, solute atoms which are attracted to vacancies would, during the cooling of a sample, migrate with vacancies toward grain boundaries (vacancy sinks) and thereby enhance the solute concentration in boundary regions. For solute atoms which are not attracted to vacancies no such boundary solute enrichment would be expected. These concepts were given experimental support by boundary and bulk mi-crohardness measurements of various thermally treated dilute zinc and lead alloys and also doped aluminum oxide. The underlying assumption in their work was that solute enrichment in boundary regions is indicated by higher microhardness values. From thermodynamic considerations1&apos;2 it appears that the solid-liquid solute distribution coefficient (K), defined as the concentration of solute in the solid to the concentration of solute in the liquid at equilibrium, indicates whether attractive or repulsive forces exist between vacancies and solute atoms. K < 1 indicates a solute-vacancy attractions, K > 1 indicates no, or a repulsive, vacancy-solute interaction. This note is to report on observations of different grain boundary etching phenomena in high purity zinc alloys. These phenomena appear to depend on whether a K < 1 or K > 1 solute is present. In experiments designed to measure directly the solute enrichment in grain boundary regions, samples of zone refined zinc with 0.1 at. pct solute additions were cooled from 380°C at a rate of 3°C per min. A surface layer of approximately 50 was then removed from the samples by chemical polishing. The samples&apos; surfaces were then protected by a chromating treatment such that in a subsequent etch only grain boundary regions were dissolved. The dissolved regions were approximately semicircular troughs, 10 µ in width. The grain boundaries were usually in the middle, i.e., at the bottom, of this trough. For zinc containing the K < 1 solutes cadmium and aluminum, the grain boundary was always indicated by a ridge as shown in Fig. 1. For pure zinc, and zinc containing the K > 1 solutes copper and gold, a groove at the bottom of the trough indicated the boundary position, Fig. 2., To test if these different grain boundary etching behaviors were possibly connected with the segregation process discussed above, the Zn-Cd alloy was again heated to 380°C and quenched into brine. After surface protection and etching it was found that this specimen no longer exhibited the grain boundary ridges but rather grain boundary grooves as shown in Fig. 2. It would appear, therefore, that the boundary ridge is a consequence of a process occurring during the slow cooling of the samples. From absorption spectrophotometric analysis it was found that for slowly cooled samples containing K < 1 solutes, the solute/zinc ratios of the material from the boundary trough were consistently considerably higher than the solute/zinc ratios of the bulk alloys. This boundary region solute enrichment was not observed in quenched samples. It is concluded therefore, that the boundary ridge shown in Fig. 1 is directly or indirectly connected with nonequilibrium solute segregation.

Jan 1, 1970

By W. R. Davis

This paper presents a sunimary of the results of a study of the Dornick Hills-Springer sand reservoir of the Velma Pool. Stephens County, Oklahoma. The data are of interest because this type of reservoir is unusual in the mid-continent area. The reservoir is characterized by very steep dips and a relatively thick producing section. Its up-dip productive limit is defined by truncation of the productive sands, and the down-dip limit is defined by deterioration of sand quality rather than by the presence of an oil-water contact. The crude oil is of 29" API gravity, is relatively viscous and was saturated with dissolved gas at the original reservoir pressure. Consideratiqn of the physical characteristics of the reservoir indicates that natural water encroachment will be negligible, and that the producing mechanism will be a dissolved gas drive augmented by gravity drainage. Performance to date tends to confirm this. INTRODUCTION It is the purpose of this paper to present some of the features of the Dor-nick Hills - Springer sand reservoir which are unusual in mid-continent operations. The study was undertaken in an attempt to define the producing mechanism or mechanisms that will control reservoir performance, as an aid in determining well completion and production practices. GEOLOGY The reservoir under consideration is a series of sand bodies of Pennsylva-nian age found in the Lower Dornick Hills and/or Springer formations. For the purpose of this paper, the sand series is referred to as the Dornick Hills-Springer sand. This sand series lies on the northeast flank of the Velma anticline, and dips very sharply to the northeast in TWP 1S-5W, the average dip being about 45º. However, as shown in Fig. 1. the trend of the pool swings eastward in TWP 1S-4W with a coincident de- crease in dip angle. In this portion of the pool the average dip is about 25". Faults in Sections 30-1S-4W and 32-1S-4W are shown in Fig. 1. These faults show only minor displacements for the horizon contoured in Fig. 1, but they do show a pronounced displacement of the immediately overlying beds. Similar faults are thought to exist in TWP 1S-5W; however, since the detailed geological studies necessary to properly define these faults were not available to the author, no attempt to show them in Fig. 1 has been made. The up-dip productive limit throughout the pool is determined by the truncation of the Lower Dornick Hills-Springer sand. The down-dip productive limit does not appear to be defined by edge water, but by a gradual reduction in permeability of the sands. No dry hole has produced a significant volume of water from this sand section. There was a small gas cap in TWP 1S-5W. Most of the wells in TWP 1S-SW encountered an oil sand 70 ft to 150 ft thick, a shale 20 ft to 80 ft thick, and another oil sand 50 ft to 130 ft thick. A few scattered wells in this area encountered other and bodies below these

Jan 1, 1951

By W. R. Davis

This paper presents a sunimary of the results of a study of the Dornick Hills-Springer sand reservoir of the Velma Pool. Stephens County, Oklahoma. The data are of interest because this type of reservoir is unusual in the mid-continent area. The reservoir is characterized by very steep dips and a relatively thick producing section. Its up-dip productive limit is defined by truncation of the productive sands, and the down-dip limit is defined by deterioration of sand quality rather than by the presence of an oil-water contact. The crude oil is of 29" API gravity, is relatively viscous and was saturated with dissolved gas at the original reservoir pressure. Consideratiqn of the physical characteristics of the reservoir indicates that natural water encroachment will be negligible, and that the producing mechanism will be a dissolved gas drive augmented by gravity drainage. Performance to date tends to confirm this. INTRODUCTION It is the purpose of this paper to present some of the features of the Dor-nick Hills - Springer sand reservoir which are unusual in mid-continent operations. The study was undertaken in an attempt to define the producing mechanism or mechanisms that will control reservoir performance, as an aid in determining well completion and production practices. GEOLOGY The reservoir under consideration is a series of sand bodies of Pennsylva-nian age found in the Lower Dornick Hills and/or Springer formations. For the purpose of this paper, the sand series is referred to as the Dornick Hills-Springer sand. This sand series lies on the northeast flank of the Velma anticline, and dips very sharply to the northeast in TWP 1S-5W, the average dip being about 45º. However, as shown in Fig. 1. the trend of the pool swings eastward in TWP 1S-4W with a coincident de- crease in dip angle. In this portion of the pool the average dip is about 25". Faults in Sections 30-1S-4W and 32-1S-4W are shown in Fig. 1. These faults show only minor displacements for the horizon contoured in Fig. 1, but they do show a pronounced displacement of the immediately overlying beds. Similar faults are thought to exist in TWP 1S-5W; however, since the detailed geological studies necessary to properly define these faults were not available to the author, no attempt to show them in Fig. 1 has been made. The up-dip productive limit throughout the pool is determined by the truncation of the Lower Dornick Hills-Springer sand. The down-dip productive limit does not appear to be defined by edge water, but by a gradual reduction in permeability of the sands. No dry hole has produced a significant volume of water from this sand section. There was a small gas cap in TWP 1S-5W. Most of the wells in TWP 1S-SW encountered an oil sand 70 ft to 150 ft thick, a shale 20 ft to 80 ft thick, and another oil sand 50 ft to 130 ft thick. A few scattered wells in this area encountered other and bodies below these

Jan 1, 1951