Search Documents

By Charles Hart

The art of electric smelting came with the turn of the present century and owes its existence to the introduction of alternating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N. Y. Prior to that time current was largely direct. The furnaces were electrolytic in nature and found their first metallurgical use in the production of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific : publications and books written during the first two decades of this century. Types of Furnaces The 40 years devoted to the practice of electric smelting may be divided into two . periods of 20 years each. The first was devoted to experimentation with furnace types and with many publications on theories and processes. The second half of this term was devoted to perfecting the types of furnaces and their active commercial operation. The arc furnace may be found in three types: (1) the direct-heating arc furnace with the positive electrode included in the bottom and the other electrode suspended above; (2) the independent arc furnace with its electrodes entirely above the charge, which of necessity depends upon heat reflected from the roof; (3) the direct-heating series arc furnace equipped with two or more electrodes suspended from the roof. Of these three types, only the last is used in electric smelting of iron ore at the present time. The elimination of the other types automatically removed many of the early designs, to the end that there are now only two general types in operation: (I) the " Electrometalls" or high-shaft furnace of Sweden, and (2) the low-shaft or pit-type furnace as offered by Tysland-Hole and Siemens-Halske. The "Electrometalls" furnace takes its name from the corporation formed by the engineers that had undertaken its perfection. After trying several designs they brought forward the furnace shown in Fig. I, which by the way is the highest development of this type of furnace as of today.l Note the trend in the lines, which have kept pace with modern blast-furnace design. The high-shaft furnace lends itself to skip filling and is fitted with tuyeres immediately under the crucible roof, whereby the gases are recycled and the roof preserved. The failure of the Electrometalls furnace in Norway, because of its inability to meet

Jan 1, 1941

By Charles Hart

The art of electric smelting came with the turn of the present century and owes its existence to the introduction of alternating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N. Y. Prior to that time current was largely direct. The furnaces were electrolytic in nature and found their first metallurgical use in the production of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific : publications and books written during the first two decades of this century. Types of Furnaces The 40 years devoted to the practice of electric smelting may be divided into two . periods of 20 years each. The first was devoted to experimentation with furnace types and with many publications on theories and processes. The second half of this term was devoted to perfecting the types of furnaces and their active commercial operation. The arc furnace may be found in three types: (1) the direct-heating arc furnace with the positive electrode included in the bottom and the other electrode suspended above; (2) the independent arc furnace with its electrodes entirely above the charge, which of necessity depends upon heat reflected from the roof; (3) the direct-heating series arc furnace equipped with two or more electrodes suspended from the roof. Of these three types, only the last is used in electric smelting of iron ore at the present time. The elimination of the other types automatically removed many of the early designs, to the end that there are now only two general types in operation: (I) the " Electrometalls" or high-shaft furnace of Sweden, and (2) the low-shaft or pit-type furnace as offered by Tysland-Hole and Siemens-Halske. The "Electrometalls" furnace takes its name from the corporation formed by the engineers that had undertaken its perfection. After trying several designs they brought forward the furnace shown in Fig. I, which by the way is the highest development of this type of furnace as of today.l Note the trend in the lines, which have kept pace with modern blast-furnace design. The high-shaft furnace lends itself to skip filling and is fitted with tuyeres immediately under the crucible roof, whereby the gases are recycled and the roof preserved. The failure of the Electrometalls furnace in Norway, because of its inability to meet

Jan 1, 1941

By AIME AIME

THE quarters provided for the session on Milling Methods, Monday afternoon, Feb. 17, were filled to capacity. Galen H. Clevenger presided and notables, such as A. W. Fahrenwald, A. O. Gates, F. A. Thomson, W. L. Zeigler and others who had not graced a milling meeting in New York in recent years, or per- haps even never before, were actually present and spoke "in person." The first paper, by A. W. Fahrellwald (T. P. 275), entitled "Classifier Efficiency ; An experimental Study," was summarized by the author, who clearly showed the inconsistency of determining the efficiency of a classifier by means of sizing tests, especially where the material classified consists of a mixture of minerals of different specific gravities. In place of sieve analysis the procedure recommended involves the use of a glass settling-tube which is considered to give ideal classification and thus serve as a standard against which mill classification will be compared and relative efficiency calculated. This procedure sounds logical. Perhaps the greatest difficulty may lie in securing an ideal classifier acceptable to every one.

Jan 1, 1930

By A. F. Lucas

Belle Isle, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward published a brief account of the geology of Belle Isle and the neighboring salt islands.' In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris13 and Knapp.4 The writer's early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing hydrogen sulphide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer's direction, six wells were drilled for this syndicate during the winter of 1916-17: The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 1, 1918

By Frank E. Shepard

Electric power in mining-operations is now successfully applied to haulage, hoisting, lighting and pumping; and until lately, drilling was the one department of mining in which an electric source of energy had not been introduced. Drilling by electric power has been the field for much investigation and several forms of electric-drills have been tried; but in the severe service of rock-drilling many dieculties have been encountered, and the heavy cost of repairs has caused a deep prejudice against this system of drilling. In the majority of electric rock-drills previously placed on the market, two principal factors have been considered; first, a portable electric motor usually of heavy pattern, coupled to the driving-mechanism of the drill proper by means of a flexible shaft; and second, the coupling of some form of reciprocating cross-head to a piston by means of a spiral spring, the drill-bit being fastened to the piston-rod by some suitable form of chuck with fastening bolts and nuts. In this latter form of drill, the cross-head has a fixed stroke, while the piston with drill-bit attached is allowed a variable stroke through the

Jan 1, 1904

By A. Wahab Khair

This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally con- fined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage.

Jan 1, 1984

By Paul D. Merica

DURING the Dark Ages, when metallurgy was practiced by the alchemists, any unusual or disturbing variation in metallurgical operations was ascribed to the, presence, in the metals or ores, of an evil spirit, and it was necessary to exorcise and drive it out "by suitable incantations. In this day of science and of engineering, things still incomprehensibly go wrong in the metallurgist's work shop. The metallurgist is even now not unwilling to lay the blame for many such experiences at the door of something which intellectually- much resembles an evil spirit, "gas in the metal." The presence of gases in his metal, he knows, occasions him many very definite troubles which he can clearly distinguish and diagnose-why may it not be also responsible for those which he cannot so well understand?

Jan 1, 1931

By Joseph Lindmayer, Karl M. Busen

If silicon is in contact with silicon oxide, a heterojunction is formed which induces an inversion layer ("channel"). Influences of impurities and structural parameters on the channel are discussed. There seems to be no relation between surface damage in silicon and the channel. Phosphorz~s doping of the silicon oxide has no pronounced effect on the channel. Channels which were well above the range predicted by the heterojunction model were related to the action of H* at the silicon/silicon oxide interface. Channels which were well below tlze range predicted by the heterojunc-tion model were related to a transition region in the oxide adjacent to the interface. In support of the assumed transition region and the H+ are the ex-periments described on the paper. Furthermore, the concept of metastable OH groups in silzca, known from other publications, has been used to explain certain channel characteristics by the formation and the accommodation of hydrogen in the silicon oxide. THE electrical characteristics of a semiconductor device in many cases are influenced by the conditions of its surface. Because these conditions often are changing with temperature, time, ambient, or other parameters, numerous attempts have been undertaken to stabilize them by suitable processes. Several years ago Atallal studied the silicon/silicon dioxide interface and since then increasing attention has been given to the silicon dioxide as a means to stabilize silicon surfaces. This led to the evolution of the planar silicon devices where oxide layers are used to protect places at which the junctions are intersecting the surface. The formation of the oxide layers on silicon can be carried out by a variety of processes: high-temperature thermal oxidation (exposing the silicon surface to oxidizing agents such as 02, HzO, COz), evaporation of SiOz, or anodic oxidation of silicon. Originally the oxides were considered able to "passivate" the silicon surface and it was understood that they 1) protected the surface against any influence from the ambient and 2) stabilized surface conditions which were necessary for proper device performance. It soon was realized that the second quality was not always obtainable: Atalla and Tannenbaum showed that, in the process of forming a layer on doped silicon by thermal oxida- tion, electrically active impurities in the silicon near the interface are redistributed, thus giving rise eventually to the formation of unwanted charge distributions. The degradation of planar junctions during reoxidation of silicon was observed by Barson et a. Surface studies with silicon planar junction structures indicated that the breakdown voltage depended on the kind of procedure which was applied during or after oxidation.*" Yamin and worthinge report on charge storage and dielectric properties of SiOz films at elevated temperatures. Another influential parameter on the silicon surface is discussed by Lindmayer and usen,' namely the appearance of a surface potential on silicon as a consequence of the heterojunction formed by the silicon/silicon oxide interface. In the present paper the influence of impurities and structural parameters in silicon oxide in connection with the heterojunction is a particular object of our investigations. I) EXPERIMENTAL The material used was 10 ohm-cm p-type silicon slices with either damaged surfaces (mechanically lapped or polished) or damage-free surfaces (chemically polished). The majority of the slices were oxidized for 1 hr and 20 min at 1250°C in a steam + oxygen atmosphere generated by passing O2 through HzO at 90°C (wet oxygen). This led to oxide layers of about 9000 A. On some slices oxide layers were grown in pure oxygen (dry oxygen). By a photoresist process a set of 20 by 200 mil windows was then etched out from the oxide layer. The pattern of the windows is shown in Fig. 1. In a subsequent process n-type pockets with surface concentrations between 2 x 10" and 5 x 10" cm"3 were formed by phosphorus diffusion. This allowed ohmic contacts between the silicon surface and tungsten probes which for electrical measurements were placed into two adjoining windows and

Jan 1, 1965

By J. L. LeBlanc, R. L. Lewis

This study presents an analysis of annular backpressure variations associated with controlled gas kicks and their pronounced effect on casing .strings and exposed under lying formations. A mathematical model describing the volumetric behavior of an extraneous gas as it is transported from reservoir to .surface conditions under changing temperatures and pressures has been programmed in a Kingston FORTRAN II language for digital computer analysis. The gases under investigation typify Gulf Coast reservoir gases within a 0.6 to 0.7 .specific gravity range. The program output has been substantiated by actual field cases. of gas kicks encountered in Gulf Coart we1l.s. The development of empirical equations for calculating suitable gamy deviation factors for unique temperatures and pressures was incorporated in the program to provide realistic solution.. An output listing of annular backpressures and corresponding equivalent fluid densities resulting at a predetermined critical depth (casing setting depth) and total depth for selected .stages of circulation is provided in a chronological .sequence. Additional information including reservoir pressure and temperature, kill rnrid density, produced gas or surface volume of the expanded gas intro vion, drill pipe and annular volumes can he obtained from the model. This paper illustrates that a precise knowledge of the volumetric behavior of extraneous gases in annular flow and its effect on equivalent fluid densities at a critical depth is significant and should receive .serious consideration in controlling threatened blowouts and in the design of drilling programs. Surface pressures in excess of formation limitations are a threat to zones of lost circula/ion and are potentially injurious to productive intervals. A knowledge of annular backpressure and equivalent fluid density profiles for probable gas kicks aids in a technological accomplishment of drilling programs and provides a .sale tolerance in the event a threatened blowout is encountered. Introduction Drilling operations are frequently interrupted when the drill bit penetrates permeable gas sands with reservoir CtfuJ manuscript was received in Society of Petroleum Engineers ofice Am. 1 1967. Revised manuscript received JuIy 7. 1968. Paper (SPE 1860) kae presented at SPE 42nd Annual Fall Meeting held in Houston. Tex., Oct 1-4, 1967. @ Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineem, Inc. pressures greater than that exerted by the drilling fluid. The differential pressures resulting permit an extraneous influx of gas into the wellbore. A suspension in drilling progress is necessary to restore fluid equilibrium throughout the system. Whether formation gas kicks originate unintentionally or by design, the prospect of a threatened or actual blowout exists and a method assuring a safe and effective well control procedure must be observed. A significant contribution to well control technology was advanced by Records et a1.l in 1962. Using the concept of transmitting a constant equivalent formation pressure at the point of intrusion, Records et al. introduced a calculation technique providing the annular backpressures encountered in a well control environment as a func tion of the volumetric behavior of a 0.6 specific gravity natural gas. In essence, the procedure outlined an annular backpressure schedule in terms of fluid volume circulated at different stages of a well control operation. A number of other publications2-' proposing various techniques for controlling gas intrusions in a wellbore achieve pressure control essentially through maintenance of a constant bottom-hole pressure by surface choke adjustments. The subsequent pressure effects induced in the annulus unfortunately receive little emphasis. Due to the tedious and repetitive nature of annular backpressure computations, a theoretical solution by digital computer is introduced for predicting annular backpressure and equivalent fluid density profiles associated with controlled gas kicks. We point out the effects of volumetric behavior of extraneous gases in annular flow and related field phenomena on equivalent fluid densities at a critical depth. The investigation indicated that equivalent fluid densities at a critical depth are of significance and should receive consideration in the control of threatened blowouts and in the design of drilling programs. Theoretical Considerations The mechanism of vertical gas flow through an annulus is governed by the PVT properties of the fluid, the pressure distribution within the system, the fluid flow rates and the geometry of flow. Due to the numerous variables involved in this type of problem, certain assumptions were imposed in deriving the mathematical model and in establishing the solutions. Two gases, characterized by specific gravities of 0.6 and 0.7, were selected to typify Gulf Coast reservoir fluids. The gas intrustion entered the wellbore as an immiscible 'References given at end of paper. JOURNAL OF PETROLEUM TECHNOLOGY

Jan 1, 1969

By A. J. Opinsky

THE purpose of this note is to indicate the locations and sizes of various interstitial holes in the orthorhombic uranium lattice based on a hard-sphere model. First, plane configurations of three and four atoms will be examined, and then the true interstices surrounded by four atoms in space and by five atoms in space will be obtained. The data and notation contained in a report by Tucker' will be used. Plane Configurations Fig. 1 presents the orthorhombic uranium lattice made of spheres touching at the closest interatomic distance. The three light-colored spheres in the ab plane are illustrative of the first type of configuration to be examined. If one edge of the unit cell is taken as the origin, the three atoms can be represented by the vectors [Oi + Oj + Ok], [ai + Oj + Ok] and [(a/2)i + (b/2)j + Ok] where i, j, and k are respectively parallel to a, b, and c. In the future, this notation will be shortened to [000], [a00] and [a/2 b/2 0], respectively. A vector R = [r s t] de-scribes the position of the hole surrounded by the atoms. Since the center of the hole must be equidistant from the three atoms R2 = r2 + s2 + t2 = (r-a)2 + s2 + t2 = (r-a/2)2 + (s-b/2)2 + t2. R = [a/2 (b/4) - (a2/4b) 0] is the solution of these

Jan 1, 1955

By Kenneth A. Grace

Jan 1, 1985

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct Cr region were carefully resolved. Phase relationships in the 50 to 100 atomic pct region were outlined. A single intermediate phase, ZrCr,, was established in the system. A eutectic and a eutectoid were found in the zirconium-rich region of the system, while a eutectic was located in the chromium-rich region. Limited solubility of chromium in both a and a zirconium was observed. THIS is another in a series of papers on zirconium-base binary phase diagrams based on a program sponsored by the Atomic Energy Commission. The Zr-Sn,' Zr-Si,' and Zr-Mo and Zr-W" systems have already been published. Previous work on the Zr-Cr system includes a partial diagram by Hayes, Roberson, and Davies' and a complete diagram by McQuillan." The phase relationships reported by these authors were determined with magnesium-reduced zirconium, whereas those reported herein are based on iodide metal. Some X-ray work on the intermediate phase in this system was also reported by Hayes et al., as well as by Wallbaum.' Comparisons with these data are made in the appropriate sections. Thermal analysis, metallographic and incipient melting techniques were employed to accurately resolve phase relationships in the 0 to 50 atomic pct Cr region, while the remainder of the diagram is outlined on a basis of cast structures and thermal analysis. A description and analyses of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar (Westinghouse "Grade 3") was used. This material was produced by the decomposition of a volatile iodide onto a hot zirconium filament. The as-received crystal bar was coated with corrosion product from a standard autoclave test by which its grade designation is determined. A sand-blasting and subsequent HF-HNO, pickling treatment was employed to remove this contamination. The bars were cold-rolled to approximately 1/32-in. sheet, pickled again, sheared to 1/4-in. squares, washed with acetone, and stored for use. Ingot chromium metal from National Research Corp. and electrolytic chromium flakes from Johnson, Matthey and Co., Ltd., were available as alloy additions. The ingot chromium was received in granular form. The large granules were sized by crushing, treated for iron removal, rinsed with acetone, and stored. The flakes were broken to approximately 1/8 in. with mortar and pestle, cleaned with acetone, and stored for charging. Experimental Procedure A nonconsumable electrode arc furnace identical to that described by Hansen, Kessler, and McPher-son,' was used in this work. A 400 amp dc welding generator was the source of power. To insure homogeneity, ingots were melted in a water-cooled spun copper crucible, a total of four times without opening the furnace. No difficulties were encountered in the preparation of these binary alloys. Analyzed chromium contents were found to agree very well with the intended content. Melts of pure zirconium were interspersed in the course of preparing the alloys and their hardness was measured to keep a constant check on the melting technique. Vycor and quartz bulbs were used to contain the samples for isothermal annealing treatments. Vycor bulbs were employed for temperatures up to 110O°C, while quartz was used above this temperature. For treatments up to 950°C the bulbs were evacuated before sealing, but for higher temperatures a partial pressure of argon was admitted to the

Jan 1, 1954

By L. Wahl, M. Allard, B. Trentini

REMOVAL of sulfur in steelmaking is presently a problem of utmost importance as requirements on final sulfur contents in finished steels become increasingly strict. This is in spite of often increased sulfur contents in the fuels used during the different stages of steel processing. According to local conditions or current economic factors, sulfur can be removed during one or more of the processing operations; for instance, in a blast furnace operated under high temperatures and with a high slag basicity ratio and also by means of high inputs of manganese into the burden. These methods of proceeding are, however, expensive and in contradiction with the acid practice which is gradually being developed owing to the fact that it allows coke and lime savings and usually permits an increase of productivity. In the melting-shop, desulfurization can proceed in the open-hearth or electric furnace with one or several very basic slags, or with special prefused slags (Perrin process) mixed with steels poured from the open-hearth, electric furnace, or converter. Liquid pig iron has also been treated separately before being used in the melting shop, in order to reduce high sulfur contents. This external desul-furization has been developed in Europe for the basic Bessemer Thomas process, which is again in favor owing to the great flexibility of such installations and to the fact that the steel produced is not polluted by impurities coming from the scrap. Since the basic Bessemer process, as usually practiced, has a low desulfurizing power, external desulfurization is generally carried out in ladles by means of alkalies such as soda ash. This method, which has the advantage of being simple and costing little, has only a medium desulfurizing power, which implies the necessity for repeating the operation several times when a substantial amount of sulfur has to be removed or when very low sulfur contents are desired. Thermal losses are high and there is a considerable decrease in output. Moreover, the resulting fluid and corrosive slag, which is extremely difficult to eliminate, attacks the refractory linings of the mixers and steel furnaces. Therefore, it seems necessary to devise a simple method for external desulfurization which would not only remove substantial quantities of sulfur from the hot metal coming from an acid blast furnace, but which would also bring the sulfur contents down to the low level required in the making of high quality steel and iron. Principle of the Process In this paper a new method will be described for desulfurizing hot metal. It has been perfected by

Jan 1, 1958

By C. Norman Bowers, Blaine B. Wescott

Marked improvement in the serviceability of sucker rods has been effected in the last two years, partly because of the insistent necessity for greater economy in the operating costs of crude oil production growing out of the general industrial depression and partly because many of the recently developed fields have imposed more severe operating conditions upon both surface and underground equipment. The latter is particularly true of Kansas, where practically all of the oil produced is associated with damaging amounts of hydrogen sulfide brine and where the method of establishing potential production demands equipment capable of being operated at maximum capacity without interruptions. The decline of flush production in the Oklahoma City field created new problems in deep-well pumping on a scale heretofore unequaled and the increased proportion of water it has been necessary to produce in the fields of the Greater Seminole area presented conditions that were acutely in need of betterment. The problem in the latter fields was complicated by the shift towards sulfide characteristics, which accompanied water encroachment, and it is probably true that nowhere, at the present time, are pumping conditions generally as severe as in this territory. The Mid-Continent district, therefore, has become the proving ground for the numerous materials that have been proposed for sucker-rod fabrication. The information that ultimately will be obtained from an unprecedented amount of field experimentation will pay ample dividends when the decline of East Texas increases the demand for the vast reserves of sour crude in West Texas. It is a rare occurrence in industry that the use of such a simple piece of equipment as a sucker rod presents so complicated a problem for solution. As proof of this, it is only necessary to consider the numerous types of sucker rods on the market at the present time and contrast this condition with that of less than four years ago, when it was the common aim of manufacturers to develop a single sucker rod for all conditions of

Jan 1, 1935

THE meeting was opened, Tuesday evening, May 25th, by an address from the President, R. W. Raymond. The following persons having been duly proposed for members and associates of the Institute, were recommended by the Council for election. They were unanimously elected MEMBERS. Florian Alexander, - Newark, N. J. Charles A. Ashburner, - Philadelphia, Pa. Phineas Barnes, - Pittsburgh, Pa. J. Y. Bergen, - Chicago, 111. Leopold C. Bierwirth, - Dover, N. J. Charles E. Billin, - Philadelphia, Pa. Jerome L. Boyer, - Temple, Berks County, Pa. William S. Cherry, - Streator, Ill. Thomas Couch, - Salt Lake City, Utah. W. S. De Camp, - Boonton, N. J. Thomas Donaldson, - Boise City, Idaho. H. Firmstone, - Longdale, Va. Franz Fohr, - New York City. Richard George, - Dover, N. J. John M. Hartman, - Philadelphia, Pa. C. W. Kempton, - Newburyport, Mass. James B. Lewis, - Dover, N. J. James F. Lewis, - Amenia, Dutchess County, N. Y. Arthur H. Meyer, - St. Louis, Mo. Edward H. Morrison, - Boonton, N. J. Charles J. Norwood, - Lexington, Ky. John R. Peters, - Dover, N. J. Charles I. Rader, - Vinton Furnace, Ohio. W. M. Rees, - Stockton, Luzerne County, Pa. George Richards, - Dover, N. J. Alexander H. Sherrerd, - Scranton, Pa. W. S. Sweeny, - Easton, Pa. W. J. Taylor, - Chester, N. J. Walter Tefft, - Mineville, Essex County, N. Y. J. Alexander Tyler, - New York City. J. D. Weeks, - Pittsburgh, Pa. William Wheatley, Jr., - New York City. Moses D. Wheeler, - Virginia, Nevada. Henry Woods, - Streator, III.

Jan 1, 1876

By James K. Greenlee, David W. Wisecarver

It is estimated conservatively that some 14 billion tonnes of coal reserves in the United States exist in beds considered steeply dipping, i.e. at pitches or slopes in excess of 15O - a slope too steep for practical use of mobile wheel or crawler drive mining equipment. Past attempts to mine these steep reserves are limited owing to production difficulties and high costs, an expected result when mining of slopes must be done conventionally and mining on strike with mobile mining equipment is restricted because of limited cross sectional opening and operating room. In Europe, these adverse conditions are countered through the use of the longwall mining method. In fact, longwall mining is employed along pitches up to 55°. However, both operating and administrative - conditions in foreign steep seam coal mines differ from ours in that (1) the mine does not necessarily have to make a profit and (2) single entry development of retreat mining panels is acceptable practice. In the United States development can be done with a minimum of two entries only, provided belt haulage is not used during development.

Jan 1, 1981

By G. Sachs, A. W. Dana, C. C. Chow

A great number of the investigations on the plastic flow of metals have been concerned with the establishment of a "universal" stress-strain relation. In such a relation some stress function when plotted against a strain function should yield identical curves for the various stress states. In the first investigation of this type, Ludwik and Scheu1 plotted the maximum shearing stress as a function of the maximum principal strain. Later Ros and Eichinger2 introduced two universal stress-strain relations, the one relating the maximum shearing stress to the maximum shearing strain, and the other relating a stress invariant, suggested by von Mises and Haigh, to the corresponding strain invariant. (In more recent investigations the stress and strain invariants are frequently supplemented with some factor to render their meaning more lucid.) A further suggestion which has not attracted appreciable attention is that by Baranski³ who used stress and strain deviators. The most common means of experimentation to determine the relation between stress and strain consists in subjecting thin walled tubes to combined internal pressure and axial tension.4a,4b,4c This method allows the study of plastic flow under stresses which are variable in two directions. However, the plastic flow which can be obtained in this manner is comparatively small, being limited by either tension failure or instability. For copper,'. only the relation between maximum shearing stress and maximum shearing strain yielded good agreement. On the other hand, tests on a stee14b and on an aluminum alloy4c. resulted in systematic deviations if any of the discussed universal stress-strain relations were used. It would seem, therefore, that the agreement mentioned above for copper is only incidental and explained by its high rate of strain hardening compared to that of other metals. Much larger strains than experienced in the tube tests can be obtained by subjecting a thin membrane of a ductile metal, which is restrained at its periphery, to a uniform hydraulic pressure. The thin sheet forms a deep bulge before it fails. The stresses and strains in such a bulge increase with increasing distance from the edge of the clamping "die," the maximum stresses and strains occurring at the pole (crown) of the bulge. While the stress and strain states are determined by the contour of the bulge, the absolute magnitude of the stresses and strains depends upon the hydraulic pressure. The bulge contour is in turn correlated with the geometry of the die opening. The deformation and fracture characteristics of circular bulges, that is, bulges formed with circular clamping dies, have been the subject of numerous experimental and analytical investi-gations.5,6,7 It has been shown that plastically deformed circular bulges develop large and comparatively uniform strains before failure by instability"6b,6c,6d and closely assume a spherical shape.6d Also the distribution of strains across the contour of the bulge is dependent on the metal being investigated and is correlated with, but cannot be predicted from, the metal's stress-strain characteristics. On the other hand, oblong or elliptical bulges, that is, bulges formed with elliptical clamping dies, are not as susceptible to analytical analysis and have not been investigated to the extent that circular bulges have. The few available data6c,7c indicate that stress states are obtained at the poles of the bulges, varying between plane strain and balanced biaxial tension, depending upon the geometry of the die opening. In this paper, the strain state and curvatures exhibited by three bulge shapes, a circular and two elliptical bulges, Fig 1, are analyzed experimentally using methods described in previous publications.6a,6c An attempt is made to derive the stress-strain relations for these bulges, which represent strain states in which the ratio of the two positive principal strains varied between 1.0 and 0.35. In addition, tension tests yielded data for a value of —0.5 for this strain ratio. Such an analysis should indicate the applicability of the various laws correlating stress with strain to the stress and strain states occurring in bulged shapes. Definitions and Nomenclature The definitions of the major stress and strain quantities used in this paper are as follows: s1, s2, s3 = principal normal stresses Sl > s2 > S3 t = shear stress e = conventional (unit) strain e = In (1 + e) El, E2, E3 = principal natural strains 7 = shear strain The maximum shear stress: , _ S1 — S3 lmax = 2 Frequently, the flow stress, s1 — s3 = 2lmax rather than the maximum shear stress is used.

Jan 1, 1950

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the' second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson' argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By T. Toda, R. Maddin

A study has been made of the microstructure and mechanical properties of splat-cooled aluminum-base gold alloys with gold concentration from 0.25 to 5.0 wt pct. These alloys have been quenched from the liquid state by a torsion-catapult technique, which has made it possible to pepare specimens suitable for mechanical property measwements. From the electron micrographs it has been shown that the solid solubility of gold in aluminum can be extended to 2.5 wt pct (0.35 at. pct) by splat-cooling, while the maximum equilibrium solubility is known to be less than 0.3 wt pct (0.04 at. pct). The very fine grain size (several tenths of a micron), the extended solid solubility, and the fine dispersion of a second phase (AuAl2) contribute concurrently to a substantial strengthening effect. In Al-5 wt pct Au splat-cooled specimens of less than 50 thickness, the yield strength is 17 kg per sq mm or 6 times as large as the strength of bulk specimens. For the Al-1.0 to 2.5 wt pct Au solid solution obtained by splat-cooling, the yield strength reaches 7.5 kg per sq mm after an aging treatment (for 10 hr at 200°C), while it is 3.7 kg per sq mm for the corresponding bulk specimens. A great deal of research has been done in recent years on the structure and the properties of metals and alloys rapidly quenched from the liquid state.' The term "splat-cool" has been used with the meaning of a rapid quenching from the liquid state., The splat-cooling techniques have produced large numbers of new structures, which are expressed in terms of metastable phases,3 concentrated solid solutions,4 amorphous phases,5'6 new phases,7 and so forth. Nearly all previous studies have concentrated on the physical properties; i.e., crystallography, structure, electrical resistivity, magnetism, and so forth, of the splat-cooled metals and alloys. The mechanical strength of splat-cooled metals and alloys has hardly been investigated except for some recent work by MOSS' on A1-V alloys. The principle common to all experimental techniques developed to obtain very rapid quenching rates is based on the heat transfer by conduction. Liquid must be in good thermal contact with a substrate of high heat conductivity. Both of the published devices known as the "gun" and the "piston and anvil" techniques suffer from certain shortcomings. For example, the specimen obtained by the gun technique is very small and flaky, and hence inadequate for mechanical properties measurements. On the other hand if the material is forced to yield a continuous speci- men by the piston and anvil technique, it is probable that some plastic deformation occurs during the quench. A novel method for rapid quenching of a liquid metal or alloy, the "torsion-catapult", has been devised by Roberge and Herman9 at the University of Pennsylvania. In the apparatus the melt is thrown out of a curved furnace by a catapult and impinges on a copper substrate. The apparatus has the advantage of producing a continuous foil which is relatively large in size and of a quality suitable for the measurements of mechanical properties. The quenching rate is estimated to be of the order of l05 to l06 ºC per sec, (comparable to rates achieved by the piston and anvil technique). In selecting an alloy to be studied we were made aware of the fact that gold was believed to be "insoluble" in in and consequently age hardening in the A1-Au system appeared to be interesting. Quite recently Heirnendahl13-15 revealed that the solid solubility, as determined by transmission electron microscopy, was 0.3 wt pct Au at 640°C and 0.25 wt pct Au at 600°C, decreasing with decreasing temperature. In an A1-0.2 pct Au alloy after quenching from a solution treating temperature of 600°C the yield stress was 2 kg per sq mm, and it increased up to 6 kg per sq mm after aging for 1 to 10 hr at 200°C. The precipitation occurred in the form of platelike particles mainly on (100) matrix planes. The intermediate phase n', the equilibrium phase n (AuAl2), and lattice relationships between both precipitates and the matrix were also investigated by electron microscopy. One of the purposes of the present research is to determine whether or not the solid solubility in this system, in which gold has a very small solubility in

Jan 1, 1970

By C. D. Demond

IN reverberatory smelting, fuel is the chief item of expense, as it commonly is in processes using large percentages of it. Hence the most suitable supply is eagerly sought; that is, the supply which, in the end, yields the greatest net profit. The better grades are not infrequently bought, even at an advanced price, because they are apt to be decidedly more economical. High price, of itself, however, is no merit, for freight is generally the largest part of the cost of fuel, and the nearby supply may yield as high efficiency as that from a greater distance. If a poorer grade is reasonably good, and if its cost is low enough to more than offset the decreased technical efficiency, it is of course the more suitable. Any smelting, operation depends for both efficiency and economy on raising the furnace atmosphere considerably above the "critical" temperature; that is, above the temperature at which smelting is completed. If this temperature is not exceeded, smelting stops, no matter how much coal is burned; and the real value of a fuel depends on the number of degrees that the temperature is continuously kept above this point. For example, if one fuel maintains 2,500° F. and another only 2,100° F., while the "critical" temperature is 2,000° F., the first is worth at least five times as much as the second, although the increase above atmospheric temperature is only one-fifth more in one case than in the other. This "margin of temperature" above the smelting point is much more significant than the total number of heat units developed from the fuel. The case is parallel to that of water flowing from a pipe. The reservoir may contain a billion gallons of water; but, even though the fluid has come to the nozzle, not a drop will run out, where it can be of practical use, unless the level in the reservoir is higher than the nozzle; and the speed and volume of flow depend on how much higher the level is in the reservoir than at this point. If the temperature inn a furnace is not above the critical level there will be no slag to flow over the skimming plate, even though there are enough heat units to bring an unlimited quantity of charge up to the point of slag formation; and just as the value of a water supply for the purpose of putting out a fire depends largely on the effective head, so the difficulties of furnace management

Jan 8, 1914